Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Sample size determination”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8
All sourcesNASA NTRSDOE OSTI
NASA NTRS1972

Effect of carbide size, area, density on rolling-element fatigue

A carbide parameter that can be used to predict rolling element fatigue life was developed.The parameter is based on a statistical life analysis and incorporates the total number of particles per unit area, particle size, and percent carbide area. These were determined from quantimet image analyzing computer examinations of random samples selected from eight lots of material previously tested in rolling fatigue. The carbide parameter is independent of chemical composition, heat treatment, and hardening mechanism of the materials investigated.

Chevalier, J. L.↗
NASA NTRS1983

Analysis of a MIL-L-27502 lubricant from a gas-turbine engine test by size-exclusion chromatography

Size exclusion chromatography was used to determine the chemical degradation of MIL-L-27502 oil samples from a gas turbine engine test run at a bulk oil temperature of 216 C. Results revealed a progressive loss of primary ester and additive depletion and the formation of higher molecular weight products with time. The high molecular weight products absorbed strongly in the ultraviolet indicating the presence of chromophoric groups.

Jones, W. R., Jr.↗
NASA NTRS1983

Measurements and predictions for nonevaporating sprays in a quiescent environment

Yule et al. (1982) have conducted a study of vaporizing sprays with the aid of laser techniques. The present investigation has the objective to supplement the measurements performed by Yule et al., by considering the limiting case of a spray in a stagnant environment. Mean and fluctuating velocities of the continuous phase are measured by means of laser Doppler anemometry (LDA) techniques, while Fraunhofer diffraction and slide impaction methods are employed to determine drop sizes. Liquid fluxes in the spray are found by making use of an isokinetic sampling probe. The obtained data are used as a basis for the evaluation of three models of the process, including a locally homogeneous flow (LHF) model, a deterministic separated flow (DSF) model, and a stochastic separated flow (SSF) model. It is found that the LHF and DSF models do not provide very satisfactory predictions for the test sprays, while the SSF model does provide reasonably good predictions of the observed structure.

Solomon, A. S. P.↗
NASA NTRS1984

Elemental composition of arctic particulate matter

Measurements were made of the elemental composition of particulate matter collected in flights in the Arctic in spring 1983 as part of the Arctic Gas and Aerosol Sampling Program (AGASP). Ten samples of size-selected particles were analyzed by four nondestructive techniques at Davis. Concentrations were determined for H, C, N, and O by Forward Alpha Scattering Techniques (FAST) and for elements heavier than fluorine by Particle Induced X-ray Emission (PIXE). Total mass was measured gravimetrically, and optical absorption was measured using the Laser Integrating Plate Method (LIPM). Results of the analyses show dramatic differences in concentrations and elemental ratios from the Alaskan Arctic to the Norwegian Arctic, with indications of wood smoke and sulfuric acid in the arctic atmosphere.

Cahill, T. A.↗
NASA NTRS1991

Errors of five-day mean surface wind and temperature conditions due to inadequate sampling

Surface meteorological reports of wind components, wind speed, air temperature, and sea-surface temperature from buoys located in equatorial and midlatitude regions are used in a simulation of random sampling to determine errors of the calculated means due to inadequate sampling. Subsampling the data with several different sample sizes leads to estimates of the accuracy of the subsampled means. The number N of random observations needed to compute mean winds with chosen accuracies of 0.5 (N sub 0.5) and 1.0 (N sub 1,0) m/s and mean air and sea surface temperatures with chosen accuracies of 0.1 (N sub 0.1) and 0.2 (N sub 0.2) C were calculated for each 5-day and 30-day period in the buoy datasets. Mean values of N for the various accuracies and datasets are given. A second-order polynomial relation is established between N and the variability of the data record. This relationship demonstrates that for the same accuracy, N increases as the variability of the data record increases. The relationship is also independent of the data source. Volunteer-observing ship data do not satisfy the recommended minimum number of observations for obtaining 0.5 m/s and 0.2 C accuracy for most locations. The effect of having remotely sensed data is discussed.

Legler, David M.↗
NASA NTRS2008

Microwave Nondestructive Evaluation of Dielectric Materials with a Metamaterial Lens

A novel microwave Nondestructive Evaluation (NDE) sensor was developed in an attempt to increase the sensitivity of the microwave NDE method for detection of defects small relative to a wavelength. The sensor was designed on the basis of a negative index material (NIM) lens. Characterization of the lens was performed to determine its resonant frequency, index of refraction, focus spot size, and optimal focusing length (for proper sample location). A sub-wavelength spot size (3 dB) of 0.48 lambda was obtained. The proof of concept for the sensor was achieved when a fiberglass sample with a 3 mm diameter through hole (perpendicular to the propagation direction of the wave) was tested. The hole was successfully detected with an 8.2 cm wavelength electromagnetic wave. This method is able to detect a defect that is 0.037 lambda. This method has certain advantages over other far field and near field microwave NDE methods currently in use.

Shreiber, Daniel↗
NASA NTRS2022

Si5345, SY88422L, LT3482, and MSK130 components Total Ionizing Dose Test Report

The purpose of this test was to characterize the SI-5345, SY88422L, LT3482 and MSK130 parameter degradation for total dose response. The components are associated with REAG ID #21-024. In the test, each device was exposed to high dose rate (HDR) irradiation using gamma radiation. Device parameters such as leakage currents, timing, and overall chip health were investigated. These devices were tested for an interstellar mission on a trajectory between 0.9 AU and 5.3 AU with a 2.5-year mission, yielding an expected overall dose of 29 krad(Si)behind 1 mm of aluminum shielding (at 95% confidence; environment and dose determined through SPENVIS). This test report gives an initial look at candidate parts. Extremely small sample sizes (only 1 or 2 devices tested) do not allow consideration of part-to-part variability. High dose rates were used despite LT3482 and MSK130 having potential enhanced low dose rate sensitivity (ELDRS). Care should be taken in interpreting results given these limitations.

Total Ionizing Dose (TID)↗
NASA NTRS2023

Sintering Behaviors of ZrC, NbC, and TaC Mono-and Binary Carbides

Nuclear Thermal Propulsion (NTP) has undergone development as an alternate in-space propulsion system to traditional chemical propulsion methods since the 1950s. In an NTP system, the energy released from fission in the core is utilized as the heat source to directly heat a propellant for propulsion, rather than chemical combustion in a traditional rocket. NTP has many desirable capabilities including flexible mission launch dates and reduced transit times due to it’s capability for high specific impulse. One of the main challenges with NTP systems is the structural integrity of the fuel. The fuel form required in the reactor core must withstand temperatures above 2700 Kelvin. Ceramic-metallic matrix fuel, ceramic-ceramic matrix fuel, and solid solution carbide fuels are the three strongest candidates for the extreme environments. Solid solution carbides have the potential to exhibit promising behavior as a fuel form in an NTP system. Of the multiple refractory metal carbides of interest, here we focus on zirconium carbide (ZrC), niobium carbide (NbC), and tantalum carbide (TaC). ZrC, NbC, and TaC powders were consolidated in monocarbide (ZrC, NbC, and TaC) and bi-carbide (ZrC-NbC, ZrC-TaC, NbC-TaC) forms using spark plasma sintering (SPS). In addition to the pure endpoint carbides, the examined compositions of the various bi-carbides ranged from 25-75 mol%. The sintering temperatures, pressures, and hold times were varied to determine the ideal sintering conditions. Grain size analysis, Archimedes’ density, scanning electron microscopy (SEM), X-ray diffraction (XRD), and energy dispersion spectroscopy (EDS) were used to determine and characterize the grain size, ideal density, porosity, phase stability, and chemical composition of each sample. The data from each sample was then used to generate a Master Sintering Curve (MSC) unique to each monocarbide or bi-carbide.

nuclear thermal propulsion↗
NASA NTRS1984

The rotation of small asteroids

The Binzel and Mulholland (1983) sample of photoelectrically determined rotational parameters for 17 main belt asteroids with diameters less than 30 km are compared with previous observations of asteroids of that size range. Rigorous statistical tests are applied to investigate bias effects and quantify results on asteroid rotation. The samples are described and compared for rotational frequency, rotational amplitude, frequency distribution, and diameter and frequency dependence. It is concluded that the observed rotational frequency distribution can be acceptably fit by two Maxwellian distributions, which is consistent with the hypothesis that there are separate populations of slow and fast rotating asteroids. The frequency distributions of main belt asteroids less than 15 km in diameter and earth and Mars crossers do not differ significantly, but the larger mean lightcurve amplitude of these crossers is statistically significant. No significant diameter dependence on rotational frequency is found among the sample asteroids.

Binzel, R. P.↗
NASA NTRS1993

A test of the applicability of independent scattering to high albedo planetary regoliths

We show that 'independent scattering' is a useful approximation for high albedo particles whose size and packing density are similar to typical particles in the lunar regolith. Laboratory measurements of the intensity and linear polarization of light scattered from a laboratory sample of glass spheres of know size and composition are compared to radiative transfer calculations of the same observable quantities. Mie scattering is integrated over the size distribution of the particles to determine the mean phase and polarization functions, or phase matrix, of the particle. Assuming that the particles scatter independently, the 'doubling method' is used to rigorously calculate multiple scattering in an optically thick layer of these anisotropically scattering particles. All of the major features 'predicted' in the calculated intensity (double peaks at small phase angles) and polarization (negative branch at small phase angles, large positive peak near 20 degrees phase, and small polarization elsewhere) are observed in the laboratory measurements, with good quantitative agreement indicated at phase angles less than 90 degrees. Even though the particles are supported by physical contact with each other in the sample, as are the particles in planetary regoliths, the independent scattering calculation yields a good approximation to both the intensity and polarization. The physical parameters input to the calculation are only the size distribution of the particles and their complex index of refraction (composition). Significant advantages of this approach are that the phase matrix is calculated from basic physical principles and both the intensity and polarization are determined simultaneously. This model may have broad applications to the interpretation of photometry, spectroscopy, and polarimetry of the icy regoliths of high albedo satellites. The intent of this effort is to perform a controlled experiment that tests the utility of the independent scattering assumption

Goguen, J. D.↗
NASA NTRS2015

Presolar Materials in a Giant Cluster IDP of Probable Cometary Origin

Chondritic porous interplanetary dust particles (CP-IDPs) have been linked to comets by their fragile structure, primitive mineralogy, dynamics, and abundant interstellar materials. But differences have emerged between 'cometary' CP-IDPs and comet 81P/Wild 2 Stardust Mission samples. Particles resembling Ca-Al-rich inclusions (CAIs), chondrules, and amoeboid olivine aggregates (AOAs) in Wild 2 samples are rare in CP-IDPs. Unlike IDPs, presolar materials are scarce in Wild 2 samples. These differences may be due to selection effects, such as destruction of fine grained (presolar) components during the 6 km/s aerogel impact collection of Wild 2 samples. Large refractory grains observed in Wild 2 samples are also unlikely to be found in most (less than 30 micrometers) IDPs. Presolar materials provide a measure of primitive-ness of meteorites and IDPs. Organic matter in IDPs and chondrites shows H and N isotopic anomalies attributed to low-T interstellar or protosolar disk chemistry, where the largest anomalies occur in the most primitive samples. Presolar silicates are abundant in meteorites with low levels of aqueous alteration (Acfer 094 approximately 200 ppm) and scarce in altered chondrites (e.g. Semarkona approximately 20 ppm). Presolar silicates in minimally altered CP-IDPs range from approximately 400 ppm to 15,000 ppm, possibly reflecting variable levels of destruction in the solar nebula or statistical variations due to small sample sizes. Here we present preliminary isotopic and mineralogical studies of a very large CP-IDP. The goals of this study are to more accurately determine the abundances of presolar components of CP-IDP material for comparison with comet Wild 2 samples and meteorites. The large mass of this IDP presents a unique opportunity to accurately determine the abundance of pre-solar grains in a likely cometary sample.

Messenger, S.↗
DOE OSTI2024

Wildland–urban interface wildfire increases metal contributions to stormwater runoff in Paradise, California

The 2018 Camp Fire was a large late-year (November) wildfire that produced an urban firestorm in the Town of Paradise, California, USA, and destroyed more than 18 000 structures. Runoff from burned wildland areas is known to contain ash, which can transport contaminants including metals into nearby watersheds. However, due to historically infrequent occurrences, the effect of wildland-urban interface (WUI) fires, such as the Camp Fire, on surface water quality has not been well-characterized. Therefore, this study investigated the effects of widespread urban burning on surface water quality in major watersheds of the Camp Fire area. Between November 2018 and May 2019, 140 surface water samples were collected, including baseflow and stormflow, from burned and unburned watersheds with varying extent of urban development. Samples were analyzed for total and filter-passing metals, dissolved organic carbon, major anions, and total suspended solids. Ash and debris from the Camp Fire contributed metals to downstream watersheds via runoff throughout the storm season. Increases in concentration up to 200-fold were found for metals Cr, Cu, Ni, Pb, and Zn in burned watersheds compared to pre-fire values. Total concentrations of Al, Cd, Cu, Pb, and Zn exceeded EPA aquatic habitat acute criteria by up to 16-fold for up to five months after the fire. To assess possible transport mechanisms and bioavailability, a subset of 18 samples was analyzed using four filters with nominal pore sizes ranging from 0.22 to 1.2 μm to determine the particulate size distribution of metals. Trace and major metals (Al, Ba, Co, Cr, Cu, Fe, Hg, Mn, Ni, Pb, and Zn) were found mostly associated with larger grain sizes (>0.45 μm), and some metals (Al, Cr, Fe, and Pb) also included a substantial colloidal phase (0.22 to 0.45 μm). This study suggests that fires in the wildland–urban interface increase metal concentrations, mainly through particulate driven transport. The metals with the largest increases are likely from anthropogenic disaster materials, though biomass ash also is a major contributor to water quality. In conclusion, the increase in metals following WUI burning may have adverse ecological impacts.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2022

On the Verification of Deep Reinforcement Learning Solution for Intelligent Operation of Distribution Grids

Capabilities of deep reinforcement learning (DRL) in obtaining fast decision policies in high dimensional and stochastic environments have led to its extensive use in operational research, including the operation of distribution grids with high penetration of distributed energy resources (DER). However, the feasibility and robustness of DRL solutions are not guaranteed for the system operator, and hence, those solutions may be of limited practical value. This paper proposes an analytical method to find feasibility ellipsoids that represent the range of multi-dimensional system states in which the DRL solution is guaranteed to be feasible. Empirical studies and stochastic sampling determine the ratio of the discovered to the actual feasible space as a function of the sample size. In addition, the performance of logarithmic, linear, and exponential penalization of infeasibility during the DRL training are studied and compared in order to reduce the number of infeasible solutions

Hosseini, Mohammad Mehdi↗
NASA NTRS1982

Mass-Loss Buttons Monitor Material Degradation

Small button-sized samples attached to parent materials are simple way of monitoring degradation of parent in harsh environments. Samples determine effects of multiple exposures to environmental extremes without disturbing fit or function of parent. They are less costly and more convenient than complex instrumentation normally required to measure complete temperature/pressure time history of parent component.

Webster, C. N.↗
DOE OSTI2021

Grain size dependent high-pressure elastic properties of ultrafine micro/nanocrystalline grossular

We have performed sound velocity and unit cell volume measurements of three synthetic, ultrafine micro/nanocrystalline grossular samples up to 50 GPa using Brillouin spectroscopy and synchrotron X-ray diffraction. The samples are characterized by average grain sizes of 90 nm, 93 nm and 179 nm (hereinafter referred to as samples Gr90, Gr93, and Gr179, respectively). The experimentally determined sound velocities and elastic properties of Gr179 sample are comparable with previous measurements, but slightly higher than those of Gr90 and Gr93 under ambient conditions. However, the differences diminish with increasing pressure, and the velocity crossover eventually takes place at approximately 20–30 GPa. The X-ray diffraction peaks of the ultrafine micro/nanocrystalline grossular samples significantly broaden between 15–40 GPa, especially for Gr179. The velocity or elasticity crossover observed at pressures over 30 GPa might be explained by different grain size reduction and/or inhomogeneous strain within the individual grains for the three grossular samples, which is supported by both the pressure-induced peak broadening observed in the X-ray diffraction experiments and transmission electron microscopy observations. The elastic behavior of ultrafine micro/nanocrystalline silicates, in this case, grossular, is both grain size and pressure dependent.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Lattice Design and Advanced Modeling to Guide the Design of High-Performance Lightweight Structural Materials

Lightweight structural materials are required to increase the mobility of fission batteries. The materials must feature a robust combination of mechanical properties to demonstrate structural resilience. The primary objective of this project is to produce lightweight structural materials whose strength-to-weight ratios exceed those of the current widely used structural materials such as 316L stainless steels (316L SS). To achieve this, advanced modeling and simulation tools were employed to design lattice structures with different lattice parameters and different lattice types. A process was successfully developed for transforming lattice-structures models into Multiphysics Object Oriented Simulation Environment (MOOSE) inputs. Finite element modeling (FEM) was used to simulate the uniaxial tensile testing of the lattice-structured parts to investigate the stress distribution at a given displacement. The preliminary results showed that the lattice-structured sample displayed a lower Young’s modulus in comparison with the solid material and that the unit cell size of the lattice had a minimal effect. The novelty here is to apply up-front modeling to determine the best structure for the application before actually producing the sample. The approach of using modeling as a guiding tool for preliminary material design can significantly save time and cost for material development.

36 MATERIALS SCIENCE↗
NASA NTRS1992

Laboratory Reflectance Spectra of 160 Minerals, 0.4 to 2.5 Micrometers

This reports provides reflectance spectra of 160 minerals in both digital and printed form. In order to demonstrate the effect of particle size on reflectance, the spectral data for 135 of the minerals are presented at three different grain sizes. These are 125-500 microns, 45-125 microns and less than 45 microns. Ancillary information is provided with each mineral spectrum, which includes the mineral name, minerology, supplier, sampling locality and our designated sample number. The purity of every mineral sample was evaluated by X-ray diffraction (XRD). The composition of certain minerals known to deviate strongly from idealized end-member compositions was determined by electron microprobe analysis. The compositional information obtained by microbe analysis and accessory minerals identified by XRD are noted with the ancillary information. In addition, the spectrum acquired from the coarsest grain size available for each sample was processed with a feature-finding algorithm to quantify the characteristics of the spectral absorption features. All the reflectance spectra presented here are provided in digital form on IBM-compatible 3.5" diskettes. Also included on diskette is a program for displaying the spectral data and searching for spectral features that runs on an IBM-compatible PC with standard VCA graphics.

reflectance spectra↗
DOE OSTI2023

Accelerated fission rate irradiation design, pre-irradiation characterization, and adaptation of conventional PIE methods for U-10Mo and U-17Mo

Metallic U alloys have high U density and thermal conductivity and thus have been explored since the beginning of nuclear power research. Alloys of U with modest amounts of Mo, such as U-10 wt % Mo (U-10Mo), are of particular interest because the γ-U crystal structure in this alloying addition shows prolonged stability in reactor service. Historically, radiation data on U-10Mo fuels were collected in Na fast reactors or lower temperature research reactor conditions, but little is known about irradiation behavior, particularly swelling and creep, at irradiation temperatures between 250 and 500°C. This work discusses the methodology and pre-irradiation characterization results from a U-Mo irradiation campaign performed in the High Flux Isotope Reactor at Oak Ridge National Laboratory. U-10Mo and U-17Mo samples irradiations are being completed at temperatures ranging from 250 to 500°C to three targeted fission densities between 2 × 10 20 and 1.5 × 10 21 fissions per cubic centimeter. Swelling measurement of the specimen sizes studied here required development and assessment of new methods for volume determination before and after irradiation. Laser profilometry and X-ray computation tomography (XCT) were used to provide preirradiation characterization of samples to determine the error and applicability of each to determine swelling following irradiation. These outcomes are contextualized through use of BISON simulations performed to assess the predicted expansion of U-Mo fuels subjected to the irradiation conditions of this work. Use of existing BISON fuel performance models predicted a maximum of 7% swelling under the irradiation conditions of this study. Pre-irradiation characterization revealed the as-cast U-Mo fuel samples were uniformly large-grained fully cubic U crystals with small U-C/N bearing precipitates and pores distributed throughout. Samples were found to contain a bulk porosity between .4 and 3% because of the casting process. Local porosity in areas far from large, interconnected pores was found by Slice-and-View to be under .2%. Nanometer-sized precipitates rich in C and N were identified in all samples, likely because of impurities during the fabrication process. Dendritic bands were also observed throughout the samples. These bands were characterized by variable Mo content that deviated from the overall Mo content by 2–3 wt %. No other microstructural features were correlated to these bands. Mechanical properties were found to be slightly strengthened compared to literature reports of bulk U-Mo fuels due to the nano-scale precipitates throughout the sample.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗