Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “SLIP”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8

Modeling of Stick-Slip Behavior in Sheared Granular Fault Gouge Using the Combined Finite-Discrete Element Method

Sheared granular layers undergoing stick-slip behavior are broadly employed to study the physics and dynamics of earthquakes. In this paper, a two-dimensional implementation of the combined finite-discrete element method (FDEM), which merges the finite element method (FEM) and the discrete element method (DEM), is used to explicitly simulate a sheared granular fault system including both gouge and plate, and to investigate the influence of different normal loads on seismic moment, macroscopic friction coefficient, kinetic energy, gouge layer thickness, and recurrence time between slips. In the FDEM model, the deformation of plates and particles is simulated using the FEM formulation while particle-particle and particle-plate interactions are modeled using DEM-derived techniques. The simulated seismic moment distributions are generally consistent with those obtained from the laboratory experiments. In addition, the simulation results demonstrate that with increasing normal load, (i) the kinetic energy of the granular fault system increases; (ii) the gouge layer thickness shows a decreasing trend; and (iii) the macroscopic friction coefficient does not experience much change. Analyses of the slip events reveal that, as the normal load increases, more slip events with large kinetic energy release and longer recurrence time occur, and the magnitude of gouge layer thickness decrease also tends to be larger; while the macroscopic friction coefficient drop decreases. Finally, the simulations not only reveal the influence of normal loads on the dynamics of sheared granular fault gouge, but also demonstrate the capabilities of FDEM for studying stick-slip dynamic behavior of granular fault systems.

58 GEOSCIENCES↗

The influence of alloying on slip intermittency and the implications for dwell fatigue in titanium

Dwell fatigue, the reduction in fatigue life experienced by titanium alloys due to holds at stresses as low as 60% of yield, has been implicated in several uncontained jet engine failures. Dislocation slip has long been observed to be an intermittent, scale-bridging phenomenon, similar to that seen in earthquakes but at the nanoscale, leading to the speculation that large stress bursts might promote the initial opening of a crack. Here we observe such stress bursts at the scale of individual grains in situ, using high energy X-ray diffraction microscopy in Ti–7Al–O alloys. This shows that the detrimental effect of precipitation of ordered Ti 3 Al is to increase the magnitude of rare pri $\langle$a$\rangle$ and bas $\langle$a$\rangle$ slip bursts associated with slip localisation. By contrast, the addition of trace O interstitials is beneficial, reducing the magnitude of slip bursts and promoting a higher frequency of smaller events. This is further evidence that the formation of long paths for easy basal plane slip localisation should be avoided when engineering titanium alloys against dwell fatigue.

36 MATERIALS SCIENCE↗

Wall Slip of Semi-Solid A356 in Couette Rheometers

Wall slip of suspensions in a couette rheometer is caused by segregation of a thin layer of liquid phase adjacent to the rheometer cylinder and cup, respectively. This causes the bulk phase to slide along the walls, which means that the fluid flow velocities respective to the walls are not zero. This affects the evaluation of the rheological properties and results in apparent flow curves. Despite of the importance of understanding and controlling segregation effects, little research has been done on this subject area. Indeed in industrial casting, the die filling behaviour, and therefore the product quality, may depend on the segregation phenomena. The wall slip occurring while investigating the semi-solid aluminium alloy A356 in a couette rheometer was investigated in the present work, employing the Kiljanski method. The goal of the present work was to obtain a true flow curve of the material, eliminating the effects of wall slip. Employing the method of Kiljanski, the wall slip velocity was calculated and subtracted from the apparent velocity of the alloy. Hence, the true shear rate in the medium and the true flow curve were estimated. The wall slip effect is assumed to be negligible in a couette system with a grooved rotational rod. This assumption was set to test by comparing the flow curve calculated from a system with grooved rotational rod with the flow curve calculated with the Kiljanski method. Both methods result in identical flow curves which can be assumed to be the physically correct one.

36 MATERIALS SCIENCE↗

Determining anisotropic slip system rate sensitivities of Ti-6Al-4V using high-energy X-ray diffraction microscopy

Variation of strain rate sensitivity among different families of slip systems in the hexagonal close-packed (α) phase of titanium (Ti) alloys has the potential to alter microscale load redistribution during both creep and dwell fatigue loading. However, existing literature contains conflicting reports regarding the degree of anisotropy present in the strain rate sensitives between α slip system families across Ti alloys. Here, we quantify the strain rate sensitivity of α slip system families in Ti-6Al-4V using high-energy X-ray diffraction microscopy (HEDM). We present a novel procedure in which we utilize the HEDM-measured grain-scale stress states during stress relaxation to determine the strain rate sensitivities of the basal $\langle a \rangle$ , prismatic $\langle a \rangle$, and first-order pyramidal $\langle c + a \rangle$ slip system families. In addition, we measure the strain rate sensitivity exponent of the macroscopic response and the α phase for comparison. We find rate sensitivities for the different slip system families to range from 0.02 to 0.04, which—while varied—are relatively isotropic in comparison with some values presented in the literature. We also demonstrate the effects of the measured anisotropic rate sensitivities using crystal plasticity finite element simulations.

Peterson, Kenneth M. [Pennsylvania State Univ., Un↗

Twin nucleation and growth in hexagonal close-packed metals: The role of slip-mediated plasticity on twin embryo formation and evolution

Twinning is a key deformation mechanism in hexagonal close-packed (hcp) metals, which are typified by a lack of easily activated slip systems that can accommodate a general state of loading. Pragmatically, the nucleation and evolution of twin domains occurs concomitantly with slip, such that the eventual twin network is conditioned by both external and internal stresses resulting, among others, from the evolution of dislocations. However our understanding of the interplay between dislocations, and twin nucleation and stability remains limited. This work focuses on elucidating the influence of dislocation-mediated plasticity on the formation, growth, and stability of twin embryos. First, a new mesoscale spectral crystal plasticity-twinning framework is developed and used to quantify the change in the free energy landscape following the nucleation {$10\bar{1}2$} of twins in Mg. Representative twin morphologies are modeled under conditions of limited and profuse slip activity, which are emulative of small- and bulk-scale samples, respectively. Then, the driving traction profiles around twin embryos are investigated via a sharp interface approach to obtain insights into how concurrent slip-mediated plasticity can influence the growth/stabilization of nanometric twins. The driving traction profiles are further utilized to determine the stability of twin embryos post loading. The initial dislocation density in the samples, and within the different domains (i.e., twin vs. parent), is seen to have a significant effect on the twin nucleation stress. Namely, the activation of high levels of concomitant plasticity in the parent grain is seen to significantly drive the formation of nanometric twin nuclei at stresses as low as 250 MPa. Further, the sharp interface analysis reveals that profuse plasticity in the parent grain simultaneously alters the forward and back stresses, such that the magnitude/polarity of the driving tractions become increasingly favorable for nanometric twin growth when slip is active. Finally, prior plasticity in the parent grain is seen to result in favorable driving tractions for nanometric twin growth, even at applied stresses as low as ~ 100 MPa. In conclusion, these results are in stark contrast to a case without any dislocations, wherein applied stresses as high as ~ 500 MPa are necessary to grow the twin domains.

36 MATERIALS SCIENCE↗

Intermittent Criticality Multi‐Scale Processes Leading to Large Slip Events on Rough Laboratory Faults

Abstract We discuss data of three laboratory stick‐slip experiments on Westerly Granite samples performed at elevated confining pressure and constant displacement rate on rough fracture surfaces. The experiments produced complex slip patterns including fast and slow ruptures with large and small fault slips, as well as failure events on the fault surface producing acoustic emission bursts without externally‐detectable stress drop. Preparatory processes leading to large slips were tracked with an ensemble of ten seismo‐mechanical and statistical parameters characterizing local and global damage and stress evolution, localization and clustering processes, as well as event interactions. We decompose complex spatio‐temporal trends in the lab‐quake characteristics and identify persistent effects of evolving fault roughness and damage at different length scales, and local stress evolution approaching large events. The observed trends highlight labquake localization processes on different spatial and temporal scales. The preparatory process of large slip events includes smaller events marked by confined bursts of acoustic emission activity that collectively prepare the fault surface for a system‐wide failure by conditioning the large‐scale stress field. Our results are consistent overall with an evolving process of intermittent criticality leading to large failure events, and may contribute to improved forecasting of large natural earthquakes.

Geochemistry & Geophysics↗

Sequential slip transfer of mixed-character dislocations across Σ3 coherent twin boundary in FCC metals: a concurrent atomistic-continuum study

Sequential slip transfer across grain boundaries (GB) has an important role in size-dependent propagation of plastic deformation in polycrystalline metals. For example, the Hall–Petch effect, which states that a smaller average grain size results in a higher yield stress, can be rationalised in terms of dislocation pile-ups against GBs. In spite of extensive studies in modelling individual phases and grains using atomistic simulations, well-accepted criteria of slip transfer across GBs are still lacking, as well as models of predicting irreversible GB structure evolution. Slip transfer is inherently multiscale since both the atomic structure of the boundary and the long-range fields of the dislocation pile-up come into play. In this work, concurrent atomistic-continuum simulations are performed to study sequential slip transfer of a series of curved dislocations from a given pile-up on Σ3 coherent twin boundary (CTB) in Cu and Al, with dominant leading screw character at the site of interaction. A Frank-Read source is employed to nucleate dislocations continuously. It is found that subject to a shear stress of 1.2 GPa, screw dislocations transfer into the twinned grain in Cu, but glide on the twin boundary plane in Al. Moreover, four dislocation/CTB interaction modes are identified in Al, which are affected by (1) applied shear stress, (2) dislocation line length, and (3) dislocation line curvature. Our results elucidate the discrepancies between atomistic simulations and experimental observations of dislocation-GB reactions and highlight the importance of directly modeling sequential dislocation slip transfer reactions using fully 3D models.

36 MATERIALS SCIENCE↗

Divergent evolution of slip banding in CrCoNi alloys

Abstract Metallic materials under high stress often exhibit deformation localization, manifesting as slip banding. Over seven decades ago, Frank and Read introduced the well-known model of dislocation multiplication at a source, explaining slip band formation. Here, we reveal two distinct types of slip bands (confined and extended) in compressed CrCoNi alloys through multi-scale testing and modeling from microscopic to atomic scales. The confined slip band, characterized by a thin glide zone, arises from the conventional process of repetitive full dislocation emissions at Frank–Read source. Contrary to the classical model, the extended band stems from slip-induced deactivation of dislocation sources, followed by consequent generation of new sources on adjacent planes, leading to rapid band thickening. Our findings provide insights into atomic-scale collective dislocation motion and microscopic deformation instability in advanced structural materials.

Science & Technology - Other Topics↗

Physics informed neural network can retrieve rate and state friction parameters from acoustic monitoring of laboratory stick-slip experiments

Various machine learning (ML) and deep learning (DL) techniques have been recently applied to the forecasting of laboratory earthquakes from friction experiments. The magnitude and timing of shear failures in stick-slip cycles are predicted using features extracted from the recorded ultrasonic or acoustic emission (AE) signals. In addition, the Rate and State Friction (RSF) constitutive laws are extensively used to model the frictional behavior of faults. In this work, we use data from shear experiments coupled with passive acoustic (variance, kurtosis, and AE rate) interleaved with active source ultrasonic monitoring (transmitted wave amplitude) to develop physics-informed neural network (PINN) models incorporating the RSF law and AE rate generation equation with wave amplitude serving as a proxy for friction state variable. This PINN framework allows learning RSF parameters from stick-slip experiments rather than measuring them through a series of velocity step experiments. We observe that when the stick-slip cycles are irregular, the PINN models outperform the data-driven DL models. Transfer learning (TL) PINN models are also developed by pre-training on data collected at one normal stress level followed by forecasting shear failures and retrieving RSF parameters at other stress levels (i.e., with different recurrence intervals) after retraining on a limited amount of new data. Our findings suggest that TL models perform better compared to standalone models. Both standalone and TL PINN-estimated RSF parameters and their ground truth values show excellent agreements thus demonstrating that RSF parameters can be retrieved from laboratory stick-slip experiments using the corresponding acoustic data and that the transmitted wave amplitude provides a good representation of the evolving frictional state during stick-slips.

58 GEOSCIENCES↗

Cross slip of extended dislocations in face-centered cubic metals through phase-field modeling

Cross slip is a dislocation mechanism that significantly impacts the mechanical behavior of engineering alloys. Here, in this work, we advance a 3D phase-field dislocation dynamics (PFDD) mesoscale technique to simulate cross slip across a broad range of face-centered cubic (FCC) metals. The formulation incorporates elastic anisotropy, an FCC numerical grid, and a high-fidelity representation of the entire γ -surface from density functional theory for eight FCC metals and no adjustable parameters or rules. The relaxed core structures under zero stress for all metals are predicted to extend in plane. The analytical model for stacking fault width agrees well with the PFDD result under the assumption of elastic isotropy but overestimates it under elastic anisotropy, when the degree of anisotropy is large. The dynamic simulations are designed to elucidate the material parameters that influence the propensity for cross slip. Whether cross slip occurs under a non-Schmid stress or to bypass a hard obstacle, the critical stress to cross slip scales strongly with the anisotropic energy coefficient for a screw dislocation.

36 MATERIALS SCIENCE↗

Dephasing in Fluxonium Qubits from Coherent Quantum Phase Slips

Phase slips occur across all Josephson junctions (JJs) at a rate that increases with the impedance of the junction. In superconducting qubits composed of JJ-array superinductors—such as fluxonium—phase slips in the array can lead to decoherence. In particular, phase-slip processes at the individual array junctions can coherently interfere, each with an Aharonov-Casher phase that depends on the offset charges of the array islands. These coherent quantum phase slips (CQPS) perturbatively modify the qubit frequency, and therefore charge noise on the array islands will lead to dephasing. By varying the impedance of the array junctions, we design a set of fluxonium qubits in which the expected phase-slip rate within the JJ array changes by several orders of magnitude. We characterize the coherence times of these qubits and demonstrate that the scaling of CQPS-induced dephasing rates agrees with our theoretical model. Furthermore, we perform noise spectroscopy of two qubits in regimes dominated by either CQPS or flux noise. We find that the noise power spectrum associated with CQPS dephasing appears to be featureless at low frequencies and not 1 / f . Numerical simulations indicate that this behavior is consistent with charge noise generated by charge-parity fluctuations within the array. Our findings broadly inform JJ-array-design trade-offs, relevant for the numerous superconducting-qubit designs employing JJ-array superinductors. Published by the American Physical Society 2024

Physics↗

Stabilization of fault slip by fluid injection in the laboratory and in situ

Faults can slip seismically or aseismically depending on their hydromechanical properties, which can be measured in the laboratory. Here, we demonstrate that fault slip induced by fluid injection in a natural fault at the decametric scale is quantitatively consistent with fault slip and frictional properties measured in the laboratory. The increase in fluid pressure first induces accelerating aseismic creep and fault opening. As the fluid pressure increases further, friction becomes mainly rate strengthening, favoring aseismic slip. Our study reveals how coupling between fault slip and fluid flow promotes stable fault creep during fluid injection. Seismicity is most probably triggered indirectly by the fluid injection due to loading of nonpressurized fault patches by aseismic creep.

58 GEOSCIENCES↗

SLIPPING MAGNETIC RECONNECTION OF FLUX-ROPE STRUCTURES AS A PRECURSOR TO AN ERUPTIVE X-CLASS SOLAR FLARE

We present the quasi-periodic slipping motion of flux-rope structures prior to the onset of an eruptive X-class flare on 2015 March 11, obtained by the Interface Region Imaging Spectrograph and the Solar Dynamics Observatory . The slipping motion occurred at the north part of the flux rope and seemed to successively peel off the flux rope. The speed of the slippage was 30−40 km s{sup −1}, with an average period of 130 ± 30 s. The Si iv λ 1402.77 line showed a redshift of 10−30 km s{sup −1} and a line width of 50−120 km s{sup −1} at the west legs of slipping structures, indicative of reconnection downflow. The slipping motion lasted about 40 minutes, and the flux rope started to rise up slowly at the late stage of the slippage. Then an X2.1 flare was initiated, and the flux rope was impulsively accelerated. One of the flare ribbons swept across a negative-polarity sunspot, and the penumbral segments of the sunspot decayed rapidly after the flare. We studied the magnetic topology at the flaring region, and the results showed the existence of a twisted flux rope, together with quasi-separatrix layer (QSL) structures binding the flux rope. Our observations imply that quasi-periodic slipping magnetic reconnection occurs along the flux-rope-related QSLs in the preflare stage, which drives the later eruption of the flux rope and the associated flare.

79 ASTRONOMY AND ASTROPHYSICS↗

Proposed Cavity for Reduced Slip-Stacking Loss

This paper employs a novel dynamical mechanism to improve the performance of slip-stacking. Slip-stacking in an accumulation technique used at Fermilab since 2004 which nearly double the proton intensity. During slip-stacking, the Recycler or the Main Injector stores two particles beams that spatially overlap but have different momenta. The two particle beams are longitudinally focused by two 53 MHz 100 kV RF cavities with a small frequency difference between them. We propose an additional 106 MHz 20 kV RF cavity, with a frequency at the double the average of the upper and lower main RF frequencies. In simulation, we find the proposed RF cavity significantly enhances the stable bucket area and reduces slip-stacking losses under reasonable injection scenarios. We quantify and map the stability of the parameter space for any accelerator implementing slip-stacking with the addition of a harmonic RF cavity.

Eldred, J.↗

Evaluation of Stimulation by Shear Slip in Fractured Rock Using a 3D Coupled Thermo-Poro-Mechanical FEM

This paper presents a 3D finite element model for simulating shear slip on fractures in rock in response to coupled thermo-poro-mechanical processes. The modeling is part of a broader effort to investigate the role of pore pressure and cooling by cold water injection on shear slip and permeability increase in granitic rock using laboratory shearing experiments under triaxial conditions. In particular, 3D thermo-poro-mechanical finite element modeling and analysis of injection experiment in fractured rock has been carried out to analyze the role of pore pressure, temperature, fracture deformation and their interactions. 4-noded tetrahedral elements are employed for intact rock deformation and transport processes within the matrix. To represent the mechanical response of a fracture surface, zero thickness contact interface element is developed based on recently developed element partitioning algorithm and procedures for applying hydraulic pressure on the fracture surfaces. A Mohr-Coulomb type criterion is adapted to capture the slip on the fracture and to quantify its reversible and irreversible deformation. The numerical model has been calibrated using results from well controlled, advanced laboratory experiments. Excellent agreement between modeling and experimental observations is achieved. Simulation results illustrate that pore pressure increase and rock matrix/fracture surface cooling cause the fracture system to deform and slip. Fracture slip is promoted due to its normal stress reduction associated with cooling effect of cold fluid injection. The numerical model provides a physics-based understanding of the role of coupled processes on shear stimulation phenomenon and the resulting permeability enhancement.

58 GEOSCIENCES↗

Loading direction dependence of asymmetric response of pyramidal slip in rolled AZ31 magnesium alloy

Textured magnesium alloys usually exhibit anisotropic mechanical behavior due to the asymmetric activation of different twinning and slipping modes. This work focuses on the pyramidal slip responses of rolled AZ31 magnesium alloy under two loading conditions, compressive and tensile loading along the normal direction. Under the condition where the compressive loading direction is closely parallel to the c-axis of the unit cell, tensile twinning and basal slips are prohibited, dislocations then active and tend to accumulate at grain boundaries and form dislocation walls. Meanwhile, these dislocations exhibit zigzag morphologies, which result from the cross-slip from {$10\bar{1}1$} first-order pyramidal plane to {$11\bar{2}2$} second-order pyramidal plane, then back to {$10\bar{1}1$} first-order pyramidal plane. Under the condition where tensile twins are prevalent, {$10\bar{1}1$} first-order and {$11\bar{2}2$} second-order pyramidal dislocations are favorable to be activated. Both types of dislocations behave climb-like dissociations onto the basal plane, forming zigzag dislocations. first-order pyramidal plane to second-order pyramidal plane, then back to first-order pyramidal plane. Under the condition where tensile twins are prevalent, first-order and second-order pyramidal dislocations are favorable to be activated. Both types of dislocations behave climb-like dissociations onto the basal plane, forming zigzag dislocations.

36 MATERIALS SCIENCE↗

The Pingding segment of the Altyn Tagh Fault (91 °E): Holocene slip-rate determination from cosmogenic radionuclide dating of offset fluvial terraces

Morphochronologic slip-rates on the Altyn Tagh Fault (ATF) along the southern front of the Pingding Shan at ~90.5°E are determined by cosmogenic radionuclide (CRN) dating of seven offset terraces at two sites. The terraces are defined based upon morphology, elevation and dating, together with fieldwork and high-resolution satellite analysis. The majority of the CRN model ages fall within narrow ranges (<2 ka) on the four main terraces (T1, T2, T3 and T3'), and allow a detailed terrace chronology. Bounds on the terrace ages and offsets of 5 independent terraces yield consistent slip-rate estimates. The long-term slip-rate of 13.9 ± 1.1 mm/yr is defined at the 95% confidence level, as the joint rate probability distribution of the rate derived from each independent terrace. It falls within the bounds of all the rates defined on the central Altyn Tagh Fault between the Cherchen He (86.4°E) and Akato Tagh (~88°E) sites. This rate is ~10 mm/yr less than the upper rate determined near Tura at ~87°E, in keeping with the inference of an eastward decreasing rate due to progressive loss of slip to thrusts branching off the fault southwards but it is greater than the 9 ± 4 mm/yr rate determined at ~90°E by GPS surveys and other geodetic short-term rates defined elsewhere along the ATF. Whether such disparate rates will ultimately be reconciled by a better understanding of fault mechanics, resolved transient deformations during the seismic cycle or by more accurate measurements made with either approach remains an important issue.

58 GEOSCIENCES↗

Grain boundary slip – twin transmission in titanium

Here, using a combination of mechanical testing, scanning electron microscopy, and a unified crystal plasticity framework for discrete intragranular shear localization, we investigate intense, localized slip bands on prismatic planes and {10$\bar{1}$2} $\langle$$\bar{1}$011$\rangle$ tensile twins, and their transmission across the grain boundaries (GBs) in commercially pure titanium. The analyses show that the orientation and curvature of the GB influence the local stress fields at the GBs, and consequently, the slip/twin transmission across the boundary. In addition to host grain properties, neighboring grain properties, such as active slip systems and instances of heterogeneity like slip bands and twins, heavily affect the deformation mechanisms in each grain. Finally, the applicability of geometric factors to predict the transmission in the experimentally observed co-located pairs is discussed. The local stress field calculated by the discrete slip and twin band model is shown to be capable of determining whether a transmission has occurred in an observed co-located pair, and also the direction of the transmission.

36 MATERIALS SCIENCE↗