Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “RAM”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8

Free-jet Altitude Investigation of a 20-inch Ram-jet Combustor with a Rich Inner Zone of Combustion for Improved Low-temperature-ratio Operation

An investigation of the altitude performance of a 20-inch-diameter high-temperature-ratio ram-jet combustor which had been redesigned to provide good combustor efficiency over a wide range of temperature ratios was conducted at zero angle of attack in a free-jet facility at a Mach number of 3.0. Configurations investigated incorporated a cylindrical control sleeve which confined the injected fuel at low over-all fuel-air ratios to about 40 percent of the engine air flow. This provided an optimum fuel-air mixture over a portion of the flame holder when the over-all fuel-air ratio was about 0.02. The configurations with the control sleeve operated with good combustor efficiency at fuel-air ratios as lean as 0.015, whereas the original engine had a lean blow-out limit at a fuel-air ratio of about 0.03. The control sleeve had little effect upon the high-fuel-air-ratio performance of the engine.

COMBUSTION, RAM-JET ENGINES↗

Effect of Fuel-air Ratio Concentration in Combustion Zone on Combustion Performance of a 16-inch Ram-jet Engine

The results of fuel-air ratio and temperature surveys made in the flame stabilizing zone of a 16-inch ram-jet combustor indicated that the distribution of combustible mixture immediately downstream of a flame holder should be mechanically controlled if a preferred mixture composition is to be maintained in that zone. A sloping-baffle combustor configuration gave combustion efficiencies of 90 percent or greater over a range of fuel-air ratios from 0.010 to 0.045.

COMBUSTION - RAM-JET ENGINES↗

Effect of fuel density and heating value on ram-jet airplane range

An analytical investigation of the effects of fuel density and heating value on the cruising range of a ram-jet airplane was made. Results indicate that with present-day knowledge of chemical fuels, neither very high nor very low fuel densities have any advantages for long-range flight. Of the fuels investigated, the borohydrides and metallic boron have the greatest range potential. Aluminum and aluminum hydrocarbon slurries were inferior to pure hydrocarbon fuel and boron-hydrocarbon slurries were superior on a range basis. It was concluded that the practical difficulties associated with the use of liquid hydrogen fuel cannot be justified on a range basis.

MISSILES↗

Investigation of Three Low-temperature-ratio Combustor Configurations in a 48-inch-diameter Ram-jet Engine

A preliminary evaluation was made of three types of combustor configurations in a 48-inch-diameter ram-jet engine to determine the one with the greatest promise of ultimately achieving efficient and stable combustion at low fuel-air rations and low combustor-inlet pressure. The combustor configurations evaluated include (1) a can-piloted configuration using a gutter-type flame holder with can-type pilot burners for stability, (2) an annular-piloted configuration using a gutter-type flame holder with an annular pilot burner to provide stability and to serve as a flow divider for confined fuel-air mixing, and (3) a can-type configuration using a flow divider for confined fuel-air mixing. No modifications were made to optimize the performance of any configuration. On the basis of this preliminary evaluation at an inlet-air temperature of about 990 degrees R, the annular-piloted combustor configuration appeared to have the greatest promise of permitting combustion efficiencies in excess of 0.90 at low fuel-air ratio with combustor-inlet pressures as low as 700 pounds per square foot absolute.

COMBUSTION - RAM-JET ENGINES↗

Simulation of aerosol direct radiative forcing with RAMS-CMAQ in East Asia

The air quality modeling system RAMS-CMAQ is developed to assess aerosol direct radiative forcing by linking simulated meteorological parameters and aerosol mass concentration with the aerosol optical properties/radiative transfer module in this study. The module is capable of accounting for important factors that affect aerosol optical properties and radiative effect, such as incident wave length, aerosol size distribution, water uptake, and internal mixture. Subsequently, the modeling system is applied to simulate the temporal and spatial variations in mass burden, optical properties, and direct radiative forcing of diverse aerosols, including sulfate, nitrate, ammonium, black carbon, organic carbon, dust, and sea salt over East Asia throughout 2005. Model performance is fully evaluated using various observational data, including satellite monitoring of MODIS and surface measurements of EANET (Acid Deposition Monitoring Network), AERONET (Aerosol Robotic Network), and CSHNET (Chinese Sun Hazemeter Network). The correlation coefficients of the comparisons of daily average mass concentrations of sulfate, PM2.5, and PM10 between simulations and EANET measurements are 0.70, 0.61, and 0.64, respectively. It is also determined that the modeled aerosol optical depth (AOD) is in congruence with the observed results from the AERONET, the CSHNET, and the MODIS. The model results suggest that the high AOD values ranging from 0.8 to 1.2 are mainly distributed over the Sichuan Basin as well as over central and southeastern China, in East Asia. The aerosol direct radiative forcing patterns generally followed the AOD patterns. The strongest forcing effect ranging from -12 to -8 W m-2 was mainly distributed over the Sichuan Basin and the eastern China's coastal regions in the all-sky case at TOA, and the forcing effect ranging from -8 to -4 W m-2 could be found over entire eastern China, Korea, Japan, East China Sea, and the sea areas of Japan

54 ENVIRONMENTAL SCIENCES↗

Entry trajectory, entry environment, and analysis of spacecraft motion for the RAM C-3 flight experiment

The RAM C-3 flight experiment was launched to study the problem of radiofrequency blackout at an entry velocity of 24,300 ft/sec. The flight is described, and data for the entry trajectory and environment, which include the effects of actual temperature measured the day of launch, are presented. An analysis of entry spacecraft motions was performed. This analysis included the determination of wind angles from measured accelerations and estimates of wind angles at high altitudes from gyro-measured rotation rates. The maximum wind angles were found to be less than 5 deg to the point of pitch-roll resonance where the total wind angle increased to 8.5 deg and the roll rate started decreasing. A plausible cause for the decrease in roll rate was shown to be a combination of trim angle and an offset center of gravity.

RAM↗

Free-jet Tests of a 1.1-inch-diameter Supersonic Ram-jet Engine

Results are presented of free-jet tests of a 1.1-inch-diameter hydrogen-burning ram-jet engine over a Mach number range from 1.42 to 2.28 and a Reynolds number range from 6.01 times 10 to the 6th power to 15.78 times 10 to the 6th power. Tests demonstrated the reliability and wide operating range of the engine and showed its suitability for installation on wind-tunnel models of airplane and missile configurations. A comparison of engine operation with combustion-chamber lengths of 3.33 and 1.51 engine diameters was made at a Mach number of 2.06. A maximum test thrust coefficient of 0.905 was obtained at fuel-air ratio of 0.034 and a Mach number of 2.06 for the engine with the 3.33-diameter combustion chamber.

ENGINES, RAM-JET↗

Investigation of Combustion in 16-inch Ram Jet Under Simulated Conditions of High Altitude and High Mach Number

Results obtained with three different burner configurations in a connected-pipe investigation of a 16-inch ram jet are presented. The radial position of the fuel injector and the engine-outlet area both affected burner performance. For a given configuration, only slight changes in total-pressure ratio across the combustion chamber were obtained over the complete range of operation. With one burner, combustion efficiencies obtained at a combustion-chamber-inlet static pressure of 800 pounds per square foot absolute were greater than those obtained at 1920 pounds per square foot absolute.

ENGINES, RAM JET↗

Altitude-test-chamber Investigation of Performance of a 28-inch Ram-jet Engine I : Combustion and Operational Performance of Four Combustion-chamber Configurations

An altitude-test-chamber investigation of a 28-inch-diameter ram-jet engine at a simulated flight Mach number of approximately 2.0 for altitudes of 40,000 to 50,000 feet was conducted at the NACA Lewis laboratory. Three different flame holders, varying in the number and size of the annular gutters, in conjunction with several fuel-injection systems were investigated. The combustion efficiency for the flame-holder fuel-injection system that provided the best over-all operational fuel-air-ratio range (0.03 to 0.075) was over 0.9 at a fuel-air ratio of about 0.065 for the altitude range investigated.

MISSILES, SPECIFIC TYPES↗

Free-flight Performance of 16-inch-diameter Supersonic Ram-jet Units III : Four Units Designed for Combustion-chamber-inlet Mach Number of 0.245 at Free-stream Mach Number of 1.8 (units D-1, D-2, D-3, and D-4)

Performance of four 16-inch-diameter ram-jet units was determined at free-stream Mach numbers of 0.49 to 1.78 over range of gas total-temperature ratios of 1.0 to 6.1. Time histories of each flight and data on thrust, drag, diffuser efficiency, and combustion are presented. A maximum thrust coefficient of 0.88 and a maximum net acceleration of 5.13 g's were observed for the four units.

COMBUSTION - RAM-JET ENGINES↗

Force and pressure characteristics for a series of nose inlets at Mach numbers from 1.59 to 1.99 V : analysis and comparison on basis of ram-jet aircraft range and operational characteristics

Performance of four experimentally investigated axially symmetric spike-type nose inlets is compared on basis of ram-jet-engine aircraft range and operational problems. At design conditions, calculated peak engine efficiencies varied 25 percent from the highest value which indicates importance of inlet design. Calculations for a typical supersonic aircraft indicate possible increase in range if engine is flown at moderate angle of attack and result in engine lift utilized. For engines with fixed exhaust nozzle, propulsive thrust increases with increasing heat addition in subcritical flow region in spite of increasing additive drag. For the perforated inlet there is a range of increasing total-temperature ratios in subcritical flow region that does not yield an increase in propulsive thrust. Effects of inlet characteristics on speed stability of a typical aircraft for three types of fuel control is discussed.

ENGINES, RAM JET↗

Some control considerations for ram-jet engines / c Seymour Himmel

Control requirements were determined from calculated engine performance maps for a fixed-geometry ram jet of a configuration suitable for strategic supersonic missile propulsion. Several control schemes for attaining desired engine performance and for stabilizing missile flight velocity during cruise are presented. The advantages and disadvantages of each system are discussed.

MISSILES↗

Shape and Angle-Of-Attack Measurements of Ram-Air Parachutes by Stereo Photogrammetry in the National Full-Scale Aerodynamics Complex

US Army MC-4/5 ram-air parachutes were tested in the 80- by 120-Ft test section of the National Full-Scale Aerodynamics Complex. Arrays of targets on the upper and lower surfaces of the central cell of the canopies were measured by stereo photogrammetry, and the target positions were used to estimate both the shape of the cell and angle of attack of the canopy. Forces and moments were measured by a six-axis load cell. Based on the photogrammetry and load-cell measurements, the relationships between lift, drag, and angle of attack were determined over a range of trailing-edge flap deflections, front riser lengths, and free-stream airspeeds. This paper describes the test, with an emphasis on the photogrammetry measurements, and presents a summary of results.

Ram-Air parachutes↗

Development of RAMS-CMAQ to Simulate Aerosol Optical Depth and Aerosol Direct Radiative Forcing and Its Application to East Asia

The air quality modeling system RAMS (Regional Atmospheric Modeling System)-CMAQ (Models-3 Community Multi-scale Air Quality) is developed to simulate the aerosol optical depth (AOD) and aerosol direct forcing (DF). The aerosol-specific extinction, single scattering albedo, and asymmetry factor are parameterized based on Mie theory taking into account the aerosol size distribution, composition, refractive index, and water uptake of solution particles. A two-stream solar radiative model considers all gaseous molecular absorption, Rayleigh scattering, and aerosols and clouds. RAMSCMAQ is applied to simulate all major aerosol concentrations (e.g., sulfate, nitrate, ammonium, organic carbon, black carbon, fine soil, and sea salt) and AOD and DF over East Asia in 2005. To evaluate its performance, the simulated AOD values were compared with ground-based in situ measurements. The comparison shows that RAMSCMAQ performed well in most of the model domain and generally captured the observed variations. High AOD values (0.2-1.0) mainly appear in the Sichuan Basin as well as in central and southeastern China. The geographic distribution of DF generally follows the AOD distribution patterns, and the DF at the top-of-the-atmosphere is less than -25 and -20 W m -2 in clear-sky and all-sky over the Sichuan Basin. Both AOD and DF exhibit seasonal variations with lower values in July and higher ones in January. The DF could obviously be impacted by high cloud fractions.

54 ENVIRONMENTAL SCIENCES↗

Bounce- and MLT-averaged diffusion coefficients in a physics-based magnetic field geometry obtained from RAM-SCB for the March 17 2013 storm

Local acceleration via whistler wave and particle interaction plays a significant role in particle dynamics in the radiation belt. In this work we explore gyro-resonant wave-particle interaction and quasi-linear diffusion in different magnetic field configurations related to the March 17 2013 storm. We consider the Earth's magnetic dipole field as a reference and compare the results against non-dipole field configurations corresponding to quiet and stormy conditions. The latter are obtained with the ring current-atmosphere interactions model with a self-consistent magnetic field RAM-SCB, a code that models the Earth's ring current and provides a realistic modeling of the Earth's magnetic field. By applying quasi-linear theory, the bounce- and MLT-averaged electron pitch angle, mixed term, and energy diffusion coefficients are calculated for each magnetic field configuration. For radiation belt (~1 MeV) and ring current (~100 keV) electrons, it is shown that at some MLTs the bounce-averaged diffusion coefficients become rather insensitive to the details of the magnetic field configuration, while at other MLTs storm conditions can expand the range of equatorial pitch angles where gyro-resonant diffusion occurs and significantly enhance the diffusion rates. When MLT average is performed at drift shell L = 4.25 (a good approximation to drift average), the diffusion coefficients become quite independent of the magnetic field configuration for relativistic electrons, while the opposite is true for lower energy electrons. These results suggest that, at least for the March 17 2013 storm and for L ≲ 4.25, the commonly adopted dipole approximation of the Earth's magnetic field can be safely used for radiation belt electrons, while a realistic modeling of the magnetic field configuration is necessary to describe adequately the diffusion rates of ring current electrons.

79 ASTRONOMY AND ASTROPHYSICS↗

A new ionospheric electron precipitation module coupled with RAM-SCB within the geospace general circulation model

Electron precipitation down to the atmosphere due to wave-particle scattering in the magnetosphere contributes significantly to the auroral ionospheric conductivity. In order to obtain the auroral conductivity in global MHD models that are incapable of capturing kinetic physics in the magnetosphere, MHD parameters are often used to estimate electron precipitation flux for the conductivity calculation. Such an MHD approach, however, lacks self-consistency in representing the magnetosphere-ionosphere coupling processes. In this study we improve the coupling processes in global models with a more physical method. We calculate the physics-based electron precipitation from the ring current and map it to the ionospheric altitude for solving the ionospheric electrodynamics. In particular, we use the BATS-R-US (Block Adaptive Tree Scheme-Roe type-Upstream) MHD model coupled with the kinetic ring current model RAM-SCB (Ring current-Atmosphere interaction Model with Self-Consistent Magnetic field (B)) that solves pitch angle-dependent electron distribution functions, to study the global circulation dynamics during the 25–26 January 2013 storm event. Since the electron precipitation loss is mostly governed by wave-particle resonant scattering in the magnetosphere, we further investigate two loss methods of specifying electron precipitation loss associated with wave-particle interactions: (1) using pitch angle diffusion coefficients D αα (E,α) determined from the quasi-linear theory, with wave spectral and plasma density obtained from statistical observations (named as “diffusion coefficient method”) and (2) using electron lifetimes τ(E) independent on pitch angles inferred from the above diffusion coefficients (named as “lifetime method”). We found that both loss methods demonstrate similar temporal evolution of the trapped ring current electrons, indicating that the impact of using different kinds of loss rates is small on the trapped electron population. Furthermore, for the precipitated electrons, the lifetime method hardly captures any precipitation in the large L shell (i.e., 4 < L < 6.5) region, while the diffusion coefficient method produces much better agreement with NOAA/POES measurements, including the spatial distribution and temporal evolution of electron precipitation in the region from the premidnight through the dawn to the dayside. Further comparisons of the precipitation energy flux to DMSP observations indicates that the new physics-based precipitation approach using diffusion coefficients for the ring current electron loss can explain the diffuse electron precipitation in the dawn sector, such as the enhanced precipitation flux at auroral latitudes and flux drop near the subauroral latitudes, but the traditional MHD approach largely overestimates the precipitation flux at lower latitudes.

58 GEOSCIENCES↗

Integration of RAM-SCB into the Space Weather Modeling Framework

We present that numerical simulations of the ring current are a challenging endeavor. They require a large set of inputs, including electric and magnetic fields and plasma sheet fluxes. Because the ring current broadly affects the magnetosphere-ionosphere system, the input set is dependent on the ring current region itself. This makes obtaining a set of inputs that are self-consistent with the ring current difficult. To overcome this challenge, researchers have begun coupling ring current models to global models of the magnetosphere-ionosphere system. This paper describes the coupling between the Ring current Atmosphere interaction Model with Self-Consistent Magnetic field (RAM-SCB) to the models within the Space Weather Modeling Framework. Full details on both previously introduced and new coupling mechanisms are defined. Finally, the impact of self-consistently including the ring current on the magnetosphere-ionosphere system is illustrated via a set of example simulations.

58 GEOSCIENCES↗