Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Pretreatment”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Improved valorization of sewage sludge in the circular economy by anaerobic digestion: Impact of an innovative pretreatment technology

Anaerobic digestion (AD) of sewage sludge shows low carbon conversion efficiency (CCE) due to the poor biodegradability of sewage sludge. Here, the lack of digestibility is specifically linked to the waste-activated sludge (WAS) making up the majority of sewage sludge along with a smaller portion of primary sludge, depending on the wastewater treatment plant configuration. In this study, we examine the Advanced Wet Oxidation & Steam Explosion process (AWOEx) for improving the CCE of digested sewage sludge (DSS) by thermophilic AD. The effect of the pretreatment temperature in the range between 160 and 185 °C at a fixed residence time of 20 min with and without oxygen added at a dosage of 5 % of the organics present was tested. Methane yield improved by 97.92 % to 183.91 ± 4.93 mL/g vS over the untreated DSS (control), whose methane yield was 92.92 ± 9.07 mL/g vS We have demonstrated for the first time that 84 % of the organics in sewage sludge can successfully be transformed into biogas following AWOEx pretreatment, which can contribute significantly to the circular economy instead of greenhouse gas emissions from landfilling.

09 BIOMASS FUELS↗
DOE OSTI2022

The bamboo delignification saturation point in alkaline hydrogen peroxide pretreatment and its association with enzymatic hydrolysis

A delignification saturation point (DSP) was observed for bamboo alkaline hydrogen peroxide pretreatment (AHP). Lignin removal was increased from 52.23% to ~70% when increasing H 2 O 2 dosage from 0% to 2% at the optimum pH, but it cannot be further reinforced as increasing the H 2 O 2 . With partial lignin preserved, the glucan hydrolysis yield was found to have a ceiling of ~80%. This work indicated a strong association between enzymatic digestibility and lignin removal. Anatomical analysis by fluorescence microscope and confocal Raman microscope revealed that the undegradable lignin was mainly existing in the cell corner of sclerenchyma fibers, causing the DSP in the bamboo AHP. Finally, the residual lignin in pretreated bamboo was characterized with GPC, HSQC NMR, and 31 P NMR, which revealed the nature of DSP. This study could help to understand the lignin modification during the AHP and further contribute to the establishment of a chemical-saving biorefinery.

09 BIOMASS FUELS↗
DOE OSTI2023

Atomistic origins of biomass recalcitrance in organosolv pretreatment

Separation of lignocellulosic biomass components for use in sustainable energy and biomaterials applications remains challenging, since biopolymers such as cellulose and hemicellulose carbohydrates and polyaromatic lignin are found in close proximity within the plant secondary cell wall. Organic solvents have been used to pretreat recalcitrant biomass and separate the interacting polymers, solubilizing the lignin fraction for lignin-first valorization approaches. However, no single organosolv pretreatment approach has proven superior for heterogeneous biomass samples. Here we present a complementary atomic view of interactions between biomass components using molecular simulations, specific to lignin and cellulose, resolving mechanistic hypotheses for how lignin-cellulose composition influences separation processes. Further, using lignin-cellulose binding free energy calculated using molecular simulations, we find polar protic solvents such as methanol and ethanol separate lignin from cellulose, irrespective of the charge on the lignin monomer. Aprotic organic solvents (DMSO, THF, 1,4-dioxane) separate uncharged lignin (phenols and monolignols) from cellulose, while charged lignin (cinnamates) prefer binding to cellulose.

09 BIOMASS FUELS↗
DOE OSTI2020

The effect of lignin degradation products on the generation of pseudo-lignin during dilute acid pretreatment

Pseudo-lignin is an insoluble material that tends to deposit on acidic pretreated fiber surface and negatively impacts the biological conversion of biomass to valued added products. Employing a laboratory generated acidic hydrolysate solution from dilute acid pretreatment of bamboo residues, we sought to seek an improved understanding of pseudo-lignin formation from fragmented carbohydrates. In addition, we also performed experiments to investigate how lignin model compounds interact with carbohydrates en route to pseudo-lignin’s formation. The yields of pseudo-lignin generated from xylose (CXPL) were higher than those generated from glucose (CGPL). Gas chromatography-Mass spectrometry and Foloin-Ciocalteau analysis suggested that there were more aromatic compounds in hydrolyzate during CGPL’s formation. The presence of lignin phenolic model compounds had both a positive and negative effect upon quantitative yields of pseudo-lignin. Gel permeation chromatography and NMR analysis ( 31 P and 2D-HSQC NMR) of the pseudo-lignin samples generated in the presence and absence of 4-hydroxybenzoic acid (4-HA), employed as a lignin model compound, revealed drastic differences in molecular weight, changes in hydroxyl group content, and hydrocarbon bonds, suggesting significant differences in the pseudo-lignin reaction pathways when certain lignin model compounds are present. Finally, our findings demonstrate the effects of both hemicellulose carbohydrate makeup and lignin model compound impact on the formation of pseudo-lignin and its chemical properties, suggesting a potential way to minimize pseudo-lignin formation.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2025

A “Sweet” Biorefinery: Sugar-derived ionic liquids for the pretreatment of lignocellulosic biomass

Sugar-based ionic liquids (ILs) derived from biomass-based cations (choline, betaine) and sugar-derived anions were developed as sustainable pretreatment solvents to advance the concept of self-reliant biorefinery. Cholinium gluconate ([Ch][GlcA]) enabled streamlined one-pot sorghum pretreatment without the need for pH adjustment or washing, while betainium gluconate ([Bet][GlcA]) achieved higher sugar yields, improving overall process efficiency and economics. Both ILs produced hydrolysates fully compatible with microbial fermentation, demonstrating their potential for efficient, simplified biomass conversion. This work positions sugar-based ILs as powerful platforms that unite sustainable chemistry with integrated bioprocessing, marking a pivotal step toward realizing the self-reliant biorefinery.

Biomass-based ions↗
DOE OSTI2024

Impacts of Hydrogen Bond Donor Structures in Phenolic Aldehyde Deep Eutectic Solvents on Pretreatment Efficiency

As a green solvent for biomass processing, deep eutectic solvents (DESs) have shown effectiveness in biomass processing. Here, in this study, phenolic aldehydes with different numbers of methoxy groups, including 4-hydroxybenzaldehyde (HBA, no methoxy), vanillin (VA, monomethoxy), and syringaldehyde (SA, dimethoxy) were employed to synthesize DESs with choline chloride (ChCl). The presence of methoxy groups in the hydrogen bond donor structure affected DES properties, as well as biomass pretreatment performance. The high thermal stability of phenolic aldehyde DESs was shown with over 225 °C onset temperature. The hydrogen bond donor with one aldehyde and one hydroxyl group at the para position without a methoxy group (ChCl-HBA) showed the highest xylan removal and delignification, reaching 59.3 and 88.0%, respectively, leading to the highest enzymatic hydrolysis yield. Sonication after pretreatment further enhanced the hydrolysis yields, achieving 83.3% glucan conversion and 50.1% xylan conversion. In the lignin-rich fraction, the recovered lignin showed a low weight–average molecular weight under 2100 g/mol with a relatively uniform molecular weight dispersity below 1.5. This study provides insights into how the chemical structure of hydrogen bond donors in DESs affects biomass processing and paves the way for designing effective lignin-derived DES in future biorefinery processes.

09 BIOMASS FUELS↗
DOE OSTI2025

Redistribution of Ru in Fe 2 O 3 –Ru Nanocatalysts through an Oxidative Pretreatment Improves Reverse Water–Gas Shift Activity

We have synthesized Fe–Ru nanoparticles via a solvothermal method to create catalysts for the reverse water–gas shift reaction and demonstrated the impact of reductive and oxidative pretreatments on both catalytic performance and structure. Catalytic testing showed improved activity after exposure to O 2 at 600 °C. In contrast, the activity became lower if then exposed to H 2 at 600 °C. Environmental scanning transmission electron microscopy and scanning electron microscopy showed that exposure to O 2 at 600 °C changes the morphology and completely oxidizes Fe into Fe 2 O 3 . Exposure to H 2 at elevated temperature caused Ru coalescence at the surface of the nanoparticle, forming clusters which decreased the optimization of Ru. Reoxidation of the particles exposed to H 2 , however, caused a redistribution of Ru that appears beneficial in maximizing Ru exposure and synergy with Fe oxide, with no major changes in the morphology and oxide structure. Furthermore, our diagnostics demonstrate the complex and reversible rearrangements possible in these multicomponent particles and the benefits of oxidative pretreatment to enhance or regenerate Fe–Ru catalysts in other important catalytic reactions such as Fischer–Tropsch synthesis.

Fe−Ru nanoparticles↗
DOE OSTI2023

Membrane Pretreatment and Cell Conditioning for Proton Exchange Membrane Water Electrolysis

As the research community studying proton exchange membrane water electrolysis (PEMWE) grows, it is important to develop methods that achieve transparent, reproducible research. Reproducibility of performance and durability is a challenge facing the PEMWE field, as the published literature includes a wide spread of results obtained with nominally similar materials. Prior round-robin performance benchmarking efforts [1] have identified inadequate cell conditioning as a major source of variation in apparent cell performance. Inadequate pre-treatment and conditioning can lead to instability in initial performance and adds ambiguity to durability measurements. However, excessively prolonged conditioning procedures limit the throughput of testing and the pace of research. Pretreatment and conditioning methods vary significantly across the research literature, but little systematic investigation is available into the mechanisms of these procedures or how procedural differences may impact results. This presentation will discuss investigations into the effects of membrane pre-treatment and operating procedures during cell conditioning on initial performance and catalyst-specific accelerated stress tests, with the aim of recommending procedures to enable clear, reproducible, and high-throughput research. Methods investigated include the use of hydrogen peroxide, acids, and hydration at elevated temperature for membrane pretreatment, and conditioning procedures such as current or voltage holds and cycling. The investigations cover both the impacts of these procedures on cell performance and stability as well as underlying mechanisms and processes taking place in the cell materials.

cell↗
DOE OSTI2023

Partial wet oxidation of dairy manure as a pretreatment process to produce acetic acid ‘a Source Growth of Methanogens’

Wet oxidation can be an effective process for the pretreatment of complex biomass such as lignocellulose. However, studies on the use of wet oxidation for treating solid waste such as dairy manure are limited. The use of partial wet oxidation to convert dairy manure into low molecular weight carboxylic acids as final products were investigated. This work focuses on the performance of the sub-critical wet oxidation treatment of dairy cattle manure as a conversion/pretreatment process to release matter from the lignocellulosic fraction rather than a destructive process. The operating conditions were controlled at the short residence time and optimal temperature in the presence of oxygen under a pressure of 120 psi. The thermal hydrolysis under wet oxidation significantly affected conversion manure slurry into organic acids. The concentration of acetic acid reached 1778 mg L –1 , achieved at 190°C (60 minutes reaction time) as the reaction temperature increased within the range of 150°C–200°C, total organic carbon was reduced and monomers in the process liquids decreased. On the other hand, soluble COD in process liquids increased with an increment in reaction temperature. The results provide insights into technical options to pretreat dairy manure to improve biochemical conversion yield.

09 BIOMASS FUELS↗
DOE OSTI2024

Enzymatic depolymerization of polyester: Foaming as a pretreatment to increase specific surface area

Abstract Poly(ethylene terephthalate) (PET) is widely used for its high strength‐to‐weight ratio, gas barrier properties, and chemical resistance. The growing PET use highlights the demand for a better recycling system. Enzymatic recycling, alongside mechanical and chemical methods, is eco‐friendly and yields properties similar to virgin PET. Substrate properties ( T g , crystallinity, and specific surface area [SSA]) and enzyme stability significantly impact conversion efficiency. Higher SSA and lower crystallinity tend to yield improved depolymerization when employing leaf compost‐cutinase (LCC‐ICCG) enzymes. This study explored melt extrusion and foaming as pretreatment techniques to modify PET structural properties, using a low‐cost chemical foaming agent (CFA). The monomer conversion rate and efficiency during depolymerization were measured and related to the processing, extrudate micro‐ and meso‐structure, and polyester type. Pretreated PET substrates showed reduced T g , crystallinity, density, and enhanced SSA, resulting in a 90% mass loss for foamed RPET and VPET substrates within 2 days. In contrast, PET with ~30% of cyclohexanedimethanol comonomer exhibited a nearly 50% lower depolymerization rate, with zero BHET production. It indicates that the combination of low crystallinity, low T g , and high SSA leads to improved monomer conversion. These findings emphasize the significance of amorphization and foaming in enhancing PET enzymatic depolymerization.

42 ENGINEERING↗
DOE OSTI2020

Effect of pretreatment conditions on acidity and dehydration activity of CeO 2 -MeO x catalysts

A series of MeOx-modified CeO 2 (CeO 2 -MnO x , CeO 2 -ZnO, CeO 2 -MgO, CeO 2 -CaO, and CeO 2 -Na 2 O) catalysts were prepared by the impregnation of CeO 2 with corresponding metal nitrates. Acidity and oxidation state of cerium were investigated on both oxidized and reduced catalysts by employing Fourier Transform Infrared spectroscopy (FTIR) on adsorbed pyridine and in situ H 2 -Temperature Programmed Reduction/X-ray Absorption Spectroscopy (H 2 -TPR/XAS) techniques, respectively. Metal oxide addition tended to alter both type and number of acid sites on ceria. EXAFS data showed a significant difference in N Ce-O between unmodified and CeO 2 -MeO x , suggesting that added MeO x interferes with vacancy formation on ceria during reduction. Here, in comparison with air-pretreated samples, H 2 -pretreated ones under similar conversion of 1,5 pentanediol exhibited a higher selectivity towards linear alcohols. Alcohol conversion found to correlate with total acidity (i.e., Brønsted and Lewis). CeO 2 benefited from the addition of alkali (Na) or alkaline earth metals (Mg, Ca) by producing unsaturated alcohols.

1,5-Pentanediol↗
DOE OSTI2022

Investigations into Plasma-Mediated Decomposition of Organoiodide Species as a Pretreatment for Mitigation of Radioiodine Emissions

A plasma-mediated pretreatment step is proposed to decompose methyl iodide (CH 3 I) for facilitating the capture of the iodine radioisotopes present in off-gas streams from used nuclear fuel reprocessing operations. Simulated CH 3 I gas streams were exposed to dielectric barrier discharge (DBD) plasma in a quartz glass continuous-flow reactor using copper electrodes. The kinetics of decomposition of CH 3 I in nitrogen was investigated by varying the applied voltage, inlet concentration, and residence time. The rate of decomposition was proportional to CH 3 I concentration and increased as the applied potential was increased. This effect was incorporated in the kinetics through the dependence of the rate constant on the applied electric field. Decomposition of CH 3 I was not affected by moisture, and the DBD pretreatment is likely to be similarly effective in an air environment as well; however, the results were confounded by a plasma-mediated reaction between nitrogen and oxygen.

38 RADIATION CHEMISTRY, RADIOCHEMISTRY, AND NUCLEA↗
DOE OSTI2021

Effect of Protic Ionic Liquids in Sugar Cane Bagasse Pretreatment for Lignin Valorization and Ethanol Production

Ionic liquids have been called designer solvents because it is possible to fine-tune their properties from a huge range of possible combinations of cations and anions. In this work, we evaluate the potential of protic ionic liquids (PILs) in the fractionation of sugar cane bagasse in a biorefinery context. Here, the PILs were designed to selectively solubilize lignin and leave a polysaccharides solid fraction. The carbohydrate fraction was further hydrolyzed to obtain pentose and hexose sugars, which were fermented using a pentose-consuming yeast. The results have shown that, differently from pretreatments that solubilize hemicelluloses, pentoses could be fermented together with hexoses without a prior detoxification step with high yield and productivity. The lignin recovered was characterized by 2D HSQC NMR, 31 P NMR, and GPC, showing that the design of the PIL influences lignin characteristics, but pretreatment temperature and time do not. The lignins obtained are sulfur-free, and the richness of their functional groups makes them attractive for conversion into a diversity of value-added products, which can make a biorefinery based on the proposed process viable.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Advances in ionic liquid recycling for lignocellulosic biomass pretreatment

Ionic liquids (ILs) are promising solvents for the pretreatment of lignocellulosic biomass due to their ability to disrupt cellulose, hemicellulose, and lignin structures. However, large-scale implementation requires the development of efficient recovery and recycling methods. This review provides a comprehensive analysis of the recyclability potential of ILs used in biomass pretreatment, emphasizing their mechanisms, recent innovations, and ongoing challenges. We begin by discussing the structural diversity and tunability of ILs, which underlie their effectiveness in biomass deconstruction. The distinct roles of IL anions and cations in dissolving specific biomass components are systematically presented and compared. Advances in IL recycling techniques, including antisolvent precipitation methods, membrane separation, and distillation, are critically examined, with attention to how mechanistic insights can inform the design of more efficient and selective recovery strategies. Despite progress, significant challenges remain to scaling up IL-based biomass processing, including high cost, environmental concerns, and impact of biomass-derived impurities (e.g., lignin residues, sugars, proteins) on IL purity and functionality after reuse. We also review the applicability of different ILs based on life cycle assessments and techno-economic analyses. Lastly, we identify critical research gaps and propose future directions, including the design and development of next-generation ILs with improved recyclability, reduced toxicity, and enhanced economic viability for industrial-scale applications.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Baking and plasma pretreatment of sapphire surfaces as a way to facilitate the epitaxial plasma-enhanced atomic layer deposition of GaN thin films

The growth of high-quality epitaxial gallium nitride (GaN) thin films is achieved by using a baking and plasma pretreatment of the substrate prior to the GaN plasma-enhanced atomic layer deposition (PE-ALD). In this work, it is found that such pretreatment makes the GaN films grow coherently on sapphire substrates, following a layer-by-layer growth mechanism. The deposited GaN film shows high crystalline quality, a sharp GaN/sapphire interface, and a flat surface. The possibility of growing high-quality GaN epilayers in this way broadens the range of applications for PE-ALD in GaN-based devices.

36 MATERIALS SCIENCE↗
DOE OSTI2021

CST R9120-B 30x60 Media Pretreatment and Digestion Standard Development to Support Tank Closure Cesium Removal 1A (TCCR-1A) Operations

In support of continued operations of Savannah River Remediation’s (SRR) ion exchange process to remove radioactive cesium from Savannah River Site (SRS) dissolved saltcake, referred to as the Tank Closure Cesium Removal 1A process (TCCR-1A; containing the second set of at-tank ion exchange columns), SRNL was tasked with: 1) validating the field protocol planned for pretreating the crystalline silicotitanate (CST) ion exchange media to be used in the columns, 2) preparing CST media for use in in-tank batch contact testing, and 3) developing a digestion standard to verify complete CST dissolution prior to characterization following each in-tank batch contact test. A procedure (SRNL L29 Manual, ITS-0229) was developed previously in support of the TCCR Demonstration (which contained the first set of ion exchange columns) based on evaluations of a different CST production lot with a larger particle size range to document the protocol for pretreating CST utilizing conditions similar to what will be performed in the field.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2022

Renewable Schiff-Base Ionic Liquids for Lignocellulosic Biomass Pretreatment

Growing interest in sustainable sources of chemicals and energy from renewable and reliable sources has stimulated the design and synthesis of renewable Schiff-base (iminium) ionic liquids (ILs) to replace fossil-derived ILs. In this study, we report on the synthesis of three unique iminium-acetate ILs from lignin-derived aldehyde for a sustainable “future” lignocellulosic biorefinery. The synthesized ILs contained only imines or imines along with amines in their structure; the ILs with only imines group exhibited better pretreatment efficacy, achieving >89% sugar release. Various analytical and computational tools were employed to understand the pretreatment efficacy of these ILs. This is the first study to demonstrate the ease of synthesis of these renewable ILs, and therefore, opens the door for a new class of “Schiff-base ILs” for further investigation that could also be designed to be task specific.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Unlocking High Capacity and Fast Na + Diffusion of H x CrS 2 by Proton-Exchange Pretreatment

This study presents a new material, “H x CrS 2 " (denotes approximate composition) formed by proton-exchange of NaCrS 2 which has a measured capacity of 728 mAh g -1 with significant improvements to capacity retention, sustaining over 700 mAh g -1 during cycling experiments. This is the highest reported capacity for a transition metal sulfide electrode and outperforms the most promising proposed sodium anodes to date. H x CrS 2 exhibits a biphasic structure featuring alternating crystalline and amorphous lamella on the scale of a few nanometers. This unique structural motif enables reversible access to Cr redox in the material resulting in higher capacities than seen in the parent structure which features only S redox. In conclusion, pretreatment by proton-exchange offers a route to materials such as H x CrS 2 which provide fast diffusion and high capacities for sodium-ion batteries.

25 ENERGY STORAGE↗