Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Powder”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8
All sourcesNASA NTRSDOE OSTI
NASA NTRS1996

Gas-Phase Combustion Synthesis of Aluminum Nitride Powder

Due to its combined properties of high electrical resistivity and high thermal conductivity aluminum nitride (AlN) is a highly desirable material for electronics applications. Methods are being sought for synthesis of unagglomerated, nanometer-sized powders of this material, prepared in such a way that they can be consolidated into solid compacts having minimal oxygen content. A procedure for synthesizing these powders through gas-phase combustion is described. This novel approach involves reacting AlCl3, NH3, and Na vapors. Equilibrium thermodynamic calculations show that 100% yields can be obtained for these reactants with the products being AlN, NaCl, and H2. The NaCl by-product is used to coat the AlN particles in situ. The coating allows for control of AlN agglomeration and protects the powders from hydrolysis during post-flame handling. On the basis of thermodynamic and kinetic considerations, two different approaches were employed to produce the powder, in co-flow diffusion flame configurations. In the first approach, the three reactants were supplied in separate streams. In the second, the AlCl3 and NH3 were premixed with HCl and then reacted with Na vapor. X-ray diffraction (XRD) spectra of as-produced powders show only NaCl for the first case and NaCl and AlN for the second. After annealing at 775 C tinder dynamic vacuum, the salt was removed and XRD spectra of powders from both approaches show only AlN. Aluminum metal was also produced in the co-flow flame by reacting AlCl3 with Na. XRD spectra of as-produced powders show the products to be only NaCl and elemental aluminum.

Axelbaum, R. L.↗
NASA NTRS2002

Initial Assessment of the Effects of Nonmetallic Inclusions on Fatigue Life of Powder-Metallurgy-Processed Udimet(TM) 720

The fatigue lives of modern powder metallurgy (PM) disk alloys are influenced by variabilities in alloy microstructure and mechanical properties. These properties can vary due to the different steps of materials/component processing and machining. One of these variables, the presence of nonmetallic inclusions, has been shown to significantly degrade low-cycle fatigue (LCF) life. Nonmetallic inclusions are inherent defects in powder alloys that are a by-product of powder-processing techniques. Contamination of the powder can occur in the melt, during powder atomization, or during any of the various handling processes through consolidation. In modern nickel disk powder processing facilities, the levels of inclusion contamination have been reduced to less than 1 part per million by weight. Despite the efforts of manufacturers to ensure the cleanliness of their powder production processes, the presence of inclusions remains a source of great concern for the designer. the objective of this study was to investigate the effects on fatigue life of these inclusions. Since natural inclusions occur so infrequently, elevated levels of inclusions were carefully introduced in a nickel-based disk superalloy, Udimet 720 (registered trademark of Special Metals Corporation), produced using PM processing. Multiple strain-controlled fatigue tests were then performed on this material at 650 C. Analyses were performed to compare the LCF lives and failure initiation sites as functions of inclusion content and fatigue conditions. A large majority of the failures in specimens with introduced inclusions occurred at cracks initiating from inclusions at the specimen surface. The inclusions could reduce fatigue life by up to 100 times. These effects were found to be dependent on strain range and strain ratio. Tests at lower strain ranges and higher strain ratios produced larger effects of inclusions on life.

Gabb, T. P.↗
NASA NTRS2003

Use of an Ultrasonic/Sonic Driller/Corer to Obtain Sample Powder for CHEMIN, a Combined XRD/XRF Instrument

A miniature CHEMIN XRD/XRF (X-Ray Diffraction/X-Ray Fluourescence) instrument is currently being developed for definitive mineralogic analysis of soils and rocks on Mars. One of the technical issues that must be addressed in order to enable XRD analysis on an extraterrestrial body is how best to obtain a representative sample powder for analysis. For XRD powder diffraction analyses, it is beneficial to have a fine-grained sample to reduce preferred orientation effects and to provide a statistically significant number of crystallites to the X-ray beam. Although a 2-dimensional detector as used in the CHEMIN instrument will produce good results with poorly prepared powders, the quality of the data will improve if the sample is fine-grained and randomly oriented. An Ultrasonic/Sonic Driller/Corer (USDC) currently being developed at JPL is an effective mechanism of sampling rock to produce cores and powdered cuttings. It requires low axial load (< 5N) and thus offers significant advantages for operation from lightweight platforms and in low gravity environments. The USDC is lightweight (<0.5kg), and can be driven at low power (<5W) using duty cycling. It consists of an actuator with a piezoelectric stack, ultrasonic horn, free-mass, and drill bit. The stack is driven with a 20 kHz AC voltage at resonance. The strain generated by the piezoelectric is amplified by the horn by a factor of up to 10 times the displacement amplitude. The tip impacts the free-mass and drives it into the drill bit in a hammering action. The free-mass rebounds to interact with the horn tip leading to a cyclic rebound at frequencies in the range of 60-1000 Hz. It does not require lubricants, drilling fluid or bit sharpening and it has the potential to operate at high and low temperatures using a suitable choice of piezoelectric material. To assess whether the powder from an ultrasonic drill would be adequate for analyses by an XRD/XRF spectrometer such as CHEMIN, powders obtained from the JPL ultrasonic drill were analyzed and the results were compared to carefully prepared powders obtained using a laboratory bench scale Retsch mill.

Chipera, S. J.↗
NASA NTRS2022

(Preliminary) Effects of Ball Milling Zeolite Powders for Use in Additively Manufactured Solid Sorbents

Zeolite 13X is favorable to be used as an adsorbent in carbon dioxide (CO2) removal from the spacecraft cabin air. Reducing the size of the zeolite particles and particle size distribution is thought to increase the capacity of CO2 adsorption of the zeolite 13X powder, and potentially increase its manufacturability as a paste for additive manufacturing or slip casting. This paper will go into detail on the process of using ball milling in order to reduce particle size and particle size distribution of commercial zeolite 13X powder, as well as to characterize CO2 adsorption and manufacturability of the milled powder. Both dry and wet ball milling was analyzed during the experiment. Studies were also ran on the amount of time the powder was milled, rotational speed of the milling machine, ball to powder ratio, ball to jar ratio, and ethanol to powder ratio. The processed powder was then characterized through laser diffraction, SEM, and surface measurement techniques to show that particle size and particle size distribution could be reduced, and to show the effect of the reduced particle size and particle size distribution on CO2 adsorption and manufacturability.

zeolite↗
DOE OSTI2021

Modelling the complex evaporated gas flow and its impact on particle spattering during laser powder bed fusion

The additive manufacturing (AM) of metals is becoming an increasingly important production process with the potential to replace traditional techniques such as casting. Laser Powder Bed Fusion (LPBF) is used in many applications to print metal parts from powder. The metal powder is heated locally with sufficient laser radiation that the liquid melt easily reaches its boiling temperature, which leads to a metallic vapour jet that can entrain both powder bed particles and molten droplets. The small size of laser-matter interaction site makes a detailed experimental analysis of the process challenging. Synchrotron X-ray imaging experiments are one of the few methods which can capture the dynamic melting and solidification processes. Comparing such experiments with computer simulations of the process is an important approach in order to better understand the manufacturing process and to analyse the influence of process parameters on the evaporated gas jet and the subsequent impact on particle ejection, leading to potentially reduced AM component quality. The melting and solidification of the metal powder is simulated using an Eulerian multiphase approach based on a control volume discretization of powder bed and substrate and a volume of liquid separation from melt and gas phase. The gas phase modelled as an ideal gas reaches velocities up to 100 m/s. Lagrangian particle tracking in the simulation demonstrates that the velocity fields calculated by the Eulerian multi-phase approach in combination with a standard drag-force model lead to particle accelerations in good agreement with those measured experimentally. In order to avoid numerical laborious Lagrangian calculations, a direct method to compare an Eulerian multiphase simulation with synchrotron X-ray experiments was introduced and validated. This approach is used to analyse the influence of process parameters including laser power and laser speed on the maximal acceleration of particles from the melt pool area. While the particle acceleration increases linearly with line energy in the conduction mode, a linear decrease of the acceleration with increasing line energy can be found in the transition mode before the accel-eration increases again with line energy in the keyhole mode.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Production of mechanically-generated 316L stainless steel feedstock and its performance in directed energy deposition processing as compared to gas-atomized powder

The objective of this work is to study the feasibility of mechanically-generated feedstock for use in directed energy deposition (DED) processing. Mechanically-generated powder was created by machining 316L stainless steel bar stock followed by comminution of the resulting chips through oscillation ball milling. This methodology's production yield and processing time for the specifications of a commercially available DED system are presented along with resulting powder morphology. Performance of the mechanically-generated feedstock was compared to gas-atomized powder and evaluated based on the following figures of merit: flowability, printed part height, printed part density, and chemical compositional stability throughout processing. Mechanically-generated feedstock was created to meet deposition system requirements. Compared with gas-atomized powder, mechanically-generated powder did not flow as well through the powder-delivery system. Parts printed from mechanically-generated feedstock were generally taller than their counterparts from gas-atomized feedstock, but their densities were less predictable. As a result, chemical composition of prints using both feedstocks was within standard nominal compositions for 316L stainless steel.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Advancing the Performance of Anion Exchange Membrane Electrolysis by Employing a Powder-Based Ionomer during Anode Catalyst Layer Fabrication

The performance of anion exchange membrane water electrolysis (AEMWE) can be significantly improved by utilizing powdered ionomers during the fabrication of the anode catalyst layer (CL) to modify the CL properties. When comparing powdered ionomers to dispersed ionomers across various catalysts including cobalt oxide (Co 3 O 4 ), nickel−iron oxide (NiFe 2 O 4 ), and iridium oxide (IrO 2 ) the anode fabricated with powdered ionomers demonstrates improved performance in polarization curves, enhanced charge transfer kinetics, and reduced ohmic and transport losses, as evidenced by voltage breakdown and electrochemical impedance spectroscopy analyses. Optimal performance is achieved using a Co 3 O 4 catalyst with a 10 wt % powdered ionomer via the catalystcoated substrate method. Microscopy analyses reveal that electrodes formed with powdered ionomers during fabrication exhibit a more uniform catalyst and ionomer distribution, increased porosity with smaller pore areas, improved electronic conduction with less catalyst agglomeration isolated by a nonconductive ionomer, and enhanced interfacial contact with the membrane and transport layer. These findings highlight that ionomers in a powdered form can promote beneficial properties and are a promising approach to improving AEMWE efficiency.

08 HYDROGEN↗
DOE OSTI2022

Initial results from boron powder injection experiments in WEST lower single null L-mode plasmas

Using a recently installed impurity powder dropper (IPD), boron powder (<150 μm) was injected into lower single null (LSN) L-mode discharges in WEST. IPDs possibly enable real-time wall conditioning of the plasma-facing components and may help to facilitate H-mode access in the full-tungsten environment of WEST. The discharges in this experiment featured I p = 0.5 MA, B T = 3.7 T, q 95 = 4.3, t pulse = 12–30 s, n e,0 ~ 4 × 10 19 m –2 , and P LHCD ~ 4.5 MW. Estimates of the deuterium and impurity particle fluxes, derived from a combination of visible spectroscopy measurements and their corresponding S/XB coefficients, showed decreases of ~50% in O + , N + , and C + populations during powder injection and a moderate reduction of these low-Z impurities (~50%) and W (~10%) in the discharges that followed powder injection. Along with the improved wall conditions, WEST discharges with B powder injection observed improved confinement, as the stored energy W MHD , neutron rate, and electron temperature T e increased significantly (10%–25% for W MHD and 60%–200% for the neutron rate) at constant input power. Notably, these increases in confinement scale up with the powder drop rate and are likely due to the suppression of ion temperature gradient (ITG) turbulence from changes in Z eff and/or modifications to the electron density profile.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2022

Mitigation of plasma–wall interactions with low-Z powders in DIII-D high confinement plasmas

Experiments with low-Z powder injection in DIII-D high confinement discharges demonstrated increased divertor dissipation and detachment while maintaining good core energy confinement. Lithium (Li), boron (B), and boron nitride (BN) powders were injected in H-mode plasmas (I p = 1 MA, B t = 2 T, P NB = 6 MW, < n e > = 3.6–5.0 · 10 19 m –3 ) into the upper small-angle slot divertor for 2 s intervals at constant rates of 3–204 mg s –1 . The multi-species BN powders at a rate of 54 mg s –1 showed the most substantial increase in divertor neutral compression by more than an order of magnitude and lasting detachment with minor degradation of the stored magnetic energy W mhd by 5%. Rates of 204 mg s –1 of boron nitride powder further reduce edge localized mode-fluxes on the divertor but also cause a drop in confinement performance by 24% due to the onset of an n = 2 tearing mode. The application of powders also showed a substantial improvement of wall conditions manifesting in reduced wall fueling source and intrinsic carbon and oxygen content in response to the cumulative injection of non-recycling materials. Furthermore, the results suggest that low-Z powder injection, including mixed element compounds, is a promising new core-edge compatible technique that simultaneously enables divertor detachment and improves wall conditions during high confinement operation.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2022

Initial Results from Boron Powder Injection Experiments in WEST Lower Single Null L-mode Plasmas

Using a recently installed impurity powder dropper (IPD), boron powder (< 150 μm) was injected into lower single null (LSN) L-mode discharges in WEST. IPDs possibly enable real-time wall conditioning of the plasma-facing components and may help to facilitate H-mode access in the full-tungsten environment of WEST. The discharges in this experiment featured Ip = 0.5 MA, BT = 3.7 T, q95 = 4.3, tpulse = 12–30 s, ne,0 ~ 4×1019 m-2, and PLHCD ~ 4.5 MW. Estimates of the deuterium and impurity particle fluxes, derived from a combination of visible spectroscopy measurements and their corresponding S/XB coefficients, showed decreases of ~ 50% in O+, N+, and C+ populations during powder injection and a moderate reduction of these low-Z impurities (~ 50%) and W (~ 10%) in the discharges that followed powder injection. Along with the improved wall conditions, WEST discharges with B powder injection observed improved confinement, as the stored energy WMHD, neutron rate, and electron temperature Te increased significantly (10–25% for WMHD and 60–200% for the neutron rate) at constant input power. These increases in confinement scale up with the powder drop rate and are likely due to the suppression of ion temperature gradient (ITG) turbulence from changes in Zeff and/or modifications to the electron density profile.

Boronization↗
DOE OSTI2022

An Easy‐to‐Use Custom‐Built Cell for Neutron Powder Diffraction Studies of Rechargeable Batteries

Abstract In operando powder diffraction remains one of the most powerful tools for non‐destructive investigation of battery electrode materials. While in operando X‐ray, especially synchrotron radiation, powder diffraction is by now a routine experimental technique, in operando neutron powder diffraction is still less established. We present a new electrochemical cell for in operando neutron powder diffraction, which is, first and foremost, easy to use, but can also cycle electrode materials under electrochemical conditions close to those achieved using standard laboratory cells. The cell has been designed in multiple sizes, and high‐quality electrochemical and neutron powder diffraction data is presented for sample sizes as low as 48 mg total active material. The cell handles lithium‐ion and sodium‐ion materials equally well, with no difference in how the cell is prepared and assembled. The cell is intended to be used as sample environment at powder diffractometers at the neutron facilities MLZ, ORNL and ACNS.

25 ENERGY STORAGE↗
DOE OSTI2023

First of Their Kind: Solar Cells with a Dry-Processed Perovskite Absorber Layer via Powder Aerosol Deposition and Hot-Pressing

Preparing halide perovskite films by solvent-free, powder-based processing approaches currently attracts more and more attention. However, working solar cells employing dry, powder-based halide perovskite thin films, have not been demonstrated so far. Herein, perovskite solar cells are presented where the absorber layer is prepared by transferring readily synthesized perovskite powders into a compact thin film using a fully dry-powder-processing concept. Compact thin films are deposited via an optimized powder aerosol deposition (PAD) process. Pressing at 120 °C further improves the morphology and the optoelectronic film properties. Integrating the perovskite films in a solar cell configuration results in fully working devices, with champion power conversion efficiencies of >6%. While the (optoelectronic) properties of the PAD-processed films are found to be comparable with their solution-processed counterparts, investigations of the solar cell stack suggest deterioration of the electron-transport layer properties due to the PAD process, and the presence of hydrates at the perovskite surface to be important factors that contribute to the limited solar cell efficiency. Herein, perspectives to overcome the identified limitations are outlined, emphasizing the high potential and realizability of efficient perovskite solar cells based on dry-powder-processing approaches in the future.

14 SOLAR ENERGY↗
DOE OSTI2020

High-Energy X-ray Tomographic Analysis of Precursor Metal Powders (Ti-6Al-4V) Used for Additive Manufacturing

We utilized high-energy x-ray tomography to characterize Ti-6Al-4V metal powders (both as-received and recycled) used in powder-bed additive manufacturing process. The image processing workflow was developed to process and analyze large amount of data objectively by computer program. The distribution of size and shape of the metal particles as well as defect (mainly porosity) inside the particles was analyzed with the statistical representation and resolution in micrometer. The result revealed that circular-shaped porosity with various sizes could be embedded in the powder particles. These porosities could potentially be transferred to the 3D printed part and critically affect the mechanical performance of the component. The present study shows the effectiveness of characterizing metal powders using x-ray imaging techniques where sufficient number of particles can be sampled within tens of minutes with a minimum sample preparation and high accuracy. Clear structural differences in the as-received and recycled powders were delineated that helps in determining the feasibility of using the recycled powders.

36 MATERIALS SCIENCE↗
DOE OSTI2021

In situ X-ray imaging of pore formation mechanisms and dynamics in laser powder-blown directed energy deposition additive manufacturing

Directed energy deposition (DED) additive manufacturing (AM) is receiving growing attention in many applications, such as repair, remanufacturing, and fabrication of functionally graded structures. However, the laser-matter interactions and melt pool dynamics in laser DED with powder flow are still unclear, particularly in how pores form and flow inside the melt pool during the process. Understanding the porosity formation mechanisms is critical in the qualification, certification, and overall properties of a DED AM part. Porosity is a common phenomenon and can significantly hinder the quality of DED fabricated parts, as the pores can act as sites of crack nucleation and propagation. Here in this paper, we reveal four types of pore formation mechanisms through in-situ and operando high-speed high-resolution X-ray imaging in the DED AM process. Our results confirm that porosity within the feedstock powder induces pores in the process. We also observed pore formation mechanisms unique to the laser-based, powder-blown DED process as a result of powder delivery, keyhole dynamics, melt pool dynamics, and shield gas. High-speed X-ray images provide direct evidence for pore formation mechanisms and show that the pores related to the interaction between the delivered powder and melt pool are the largest in size in laser-based powder-blown DED AM. These results will guide porosity mitigation, elimination, and control in DED AM.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Integrated modeling of boron powder injection for real-time plasma-facing component conditioning

An integrated modeling framework for investigating the application of solid boron (B) powder injection for real-time surface conditioning of plasma-facing components (PFCs) in tokamak environments is presented. Utilizing the DIII-D impurity powder dropper (IPD) setup, this study simulates B powder injection scenarios ranging from milligrams to tens of milligrams per second, corresponding to boron flux rates of 10 20 –10 21 B/s in standard L-mode conditions. The comprehensive modeling approach combines EMC3-EIRENE for simulating the deuterium plasma background and the Dust Injection Simulator (DIS) for the ablation and transport of the boron powder particles. EMC3 trace impurity fluid modeling results show substantial boron transport to the inboard lower divertor, predominantly influenced by the main ion plasma flow. The dependency on powder particle size (5-250 µm) was found to be insignificant for the scenario considered. The effects of erosion and redeposition were considered to reconcile the discrepancies with experimental observations, which saw substantial deposition on the outer divertor plasma-facing components. For this purpose, the WallDYN3D code was updated to include boron sources within the plasma domain and integrated into the modeling framework. The mixed-material migration modeling shows evolving boron deposition patterns, suggesting the formation of mixed B-C layers or predominantly B coverage depending on the powder mass flow rate. While the modeling outcomes at lower B injection rates tend to align with DIII-D experimental observations, the prediction of near-pure boron layers at higher rates has yet to be experimentally verified in the carbon environment of the DIII-D tokamak. The extensive reach of boron layers found in the modeling suggests the need for modeling that encompasses the entire wall geometry for more accurate experimental correlations. This integrated approach sets a precedent for analyzing and applying real-time in-situ boron coating techniques in advanced tokamak scenarios, potentially extendable to ITER.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2023

A Prediction Method for Catchment Efficiency Loss due to Coaxial Nozzle Wear in Powder Fed Directed Energy Deposition Systems

Abstract Powder fed laser directed energy deposition systems show significant promise and their widespread adoption could greatly advance manufacturing technology; however, a significant amount of gas atomized metal powder is wasted during material deposition. As contaminated powder must be collected and disposed of as hazardous waste, this process is often criticized for its low catchment efficiency. This presents potential implementation and scaling issues, as widespread use of this technology would directly increase the amount of contaminated powder in need of safe disposal. A direct contribution to this waste issue was identified in past work as wearing exterior and interior surfaces on a replaceable nozzle component within the additive head of such a system integrated into a hybrid manufacturing machine tool. A computational fluid dynamics simulation is developed specifically for use within the manufacturing process by predicting catchment efficiency losses before a deposition operation is performed. The model is robust enough to calculate a catchment efficiency estimate within a reasonable transition time before deposition and is designed to replace visual estimation of nozzle deterioration by the machine operator. Both of two previously identified wear modes are represented in the simulation. Their effects on powder stream geometry are discussed in detail and the results are compared with in-situ measurements of powder stream geometry and concentrations. The resulting work contributes to the growing understanding of using prediction and prevention methods on catchment efficiency related part defects within these systems.

DeWitte, Lisa↗
DOE OSTI2020

Discrete Element Method Analysis for Metal Powders Used in Additive Manufacturing, and DEM Simulation Tutorial Using LIGGGHTS-PUBLIC [PowerPoint and paper]

Discrete Element Method (DEM) is a method of analysis to evaluate the dynamic interactions between granular particles. This method has been used in the pharmaceutical industry to improve the powder compaction process for tablet manufacturing. There are also applications in agriculture, food industry, and manufacturing. Direct energy deposition is an additive manufacturing technique which uses metallic powders fed through a nozzle, melted using a directed laser, and transformed into a solid object layer by layer. One way of feeding metal particles into the system involves the use of a vibrating hopper. Given a specified amplitude and frequency input, the hopper will enable the powder to travel up a path, and inject through the system with assistance from a stream of gas. The mechanical properties of a printed object can vary, depending on the characteristics of the powder flow and the particles’ as-received properties. Improved understanding of dynamic interactions of flowing powders could enable additive manufacturing components with 2D or 3D variations in mechanical properties, e.g., density. This work uses DEM simulation software to investigate the effects of particle cohesion, friction, and density on the quality of the flow by performing an angle of repose simulation, which is often used as a metric to evaluate the flowability of powders.

36 MATERIALS SCIENCE↗
NASA NTRS1983

Surface characterization of Ti and Ti (6 percent, Al-4 percent, V) metal powders and interaction with primer solutions

The interaction of Ti and Ti 6-4 powders with water and primer solutions was investigated experimentally by measuring the heats of immersion. Similar comparative studies were made on anatase and rutile TiO2 powders. The surface oxide layers of Ti and Ti 6-4 cracked on heating in vacuum between 300 and 400 C as evidenced by high heats of immersion in both water and primer solutions. Polyimide and polyphenylquinoxaline interacted preferentially, compared with the solvents with both metal powders after outgassing at room temperature. The heats of immersion of Ti 6-4 in water, solvents, and primer solutions increased significantly after pretreatment of the powder by an alkaline etch and a phosphate-fluoride process. The TiO2 powders were not satisfactory models for the surface oxide layer on either Ti or Ti 6-4 powder.

Siriwardane, R. V.↗