Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Pelleting Process”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Reduction of Iron‐Ore Pellets Using Different Gas Mixtures and Temperatures

Direct reduction of iron ore (DRI) is gaining an increased attention due to the growing need to decarbonize industrial processes. The current industrial DRI processes are performed using reformed natural gas, which results in CO 2 emission, although it is less than carbothermic reduction in the blast furnace. Carbon‐free reduction may be realized through the utilization of green H 2 as a reducing agent, in place of natural gas. Herein, the effects of various gas mixtures and temperature on the reduction kinetics of the hematite iron‐ore pellets are focused on in this work. Pellets are reduced at 700, 800, 850, and 900 °C in hydrogen and using various gas mixes at 850 °C. Morphology of the pellets is investigated with the help of scanning electron microscopy and mercury intrusion porosimetry. The effects of temperature and gas composition on the reduction kinetics and porosity of the pellets are discussed. A notable effect of reduction rate on the internal structure of the pellets is detected, slower reduction rate yielded bigger pores offsetting the gas composition. Higher temperature results in coarser pores and higher porosity. Finally, increase of CO content in the gas mix also leads to bigger pore size.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Influence of Pelletization and Moisture Content of Oil Palm Empty Fruit Bunches (EFBs) on Dynamic Gasification Performance

Wet-ground empty fruit bunches (EFBs), dry-ground EFB, and pelletized EFB were gasified in a laboratory-scale updraft fixed-bed reactor at differing temperatures and equivalent ratios (ERs) between 0.19 and 0.78 to evaluate the performance and quality of the syngas under autothermal operating conditions. In addition, the theoretical estimation of the key performance indicator of the ashes on the performance of the gasification process was obtained. The results show that for ERs > 0.4 the autothermal operating condition was achieved for pretreatments with pelletized and dry-ground EFBs, with reactor operating temperatures T > 700 °C. With wet EFB, this condition is achieved at any ER value. The average composition of the syngas from pelletized EFB presented the best average concentrations of the combustible species CO, H2, and CH4 when the ER values were between 0.25 and 0.40. The highest hot and cold thermal efficiency values were obtained for the gasification of EFB pellets with ER values between 0.25 and 0.40. For ground EFB, increases in the ER value led to improvements in hot thermal efficiency. Finally, during the EFB pellet gasification tests, no agglomeration and sintering problems were evidenced in comparison with wet-ground and dry-ground EFBs that showed slag formation, especially at ER < 0.46.

29 ENERGY PLANNING, POLICY, AND ECONOMY↗
NASA NTRS2004

Identifying the Parent Body of the Tagish Lake Meteorite and Characterizing its Internal Heating History and Surface Processes

This short (1-year) funded research encompassed laboratory measurements of the Tagish Lake meteorite samples, experiments of simulated space weathering on them, and comparison with D, T, and P asteroids in reflectance spectrum. In spite of its limited funding and period, we have performed said experiments here at Brown University and at University of Tokyo. Some of the major results were reported at the Lunar and Planetary Science Conference held in Houston in March, 2004. The Tagish Lake meteorite shows a unique visible reflectance spectrum identical to that of the D and T type asteroids. After the present heating experiments at even the lowest temperature of 100 C, the characteristic spectral slope of the Tagish Lake meteorite sample increased. On the other hand, after irradiating its pellet sample with pulse laser, the slope decreased. As the result, the Tagish Lake meteorite and its processed samples have come to cover a wide range of visible reflectance spectra in slope from the C-type asteroids to some extreme T/D-type asteroids, including the P-type asteroids in between. Therefore, logically speaking, our initial affirmation that the Tagish Lake meteorite must have come from one of the D-type asteroids can be wrong if such a meteoritic material is hidden under a space-weathered surface regolith of a C-type asteroid. However, such a case is likely to have a small probability in general. Other major hits of this research includes the first spectral fitting of the P-type asteroids using reflectance spectra derived from the present research. This topic needs more experiments and analysis to be addressed uniquely, and thus further efforts will be proposed.

Hiroi, Takahiro↗
DOE OSTI2026

Revisiting the Anisotropic Complex Refractive Indices of Sodium Nitrate for Interpretation of the Reflectance Spectrum of Pressed Pellets

Reflectance spectroscopy is notoriously confounding in that the measured spectral response is highly dependent upon the morphology of the sample. Fortunately, all such perturbations are neatly encoded by the complex refractive index of the sample. Herein, we seek to quantitatively model the measured infrared reflectance spectrum of a specularly flat pressed pellet sample of the birefringent compound, sodium nitrate. Single crystals of sodium nitrate were synthesized via a slow evaporation process and spectroscopically analyzed using polarization-dependent infrared single-angle reflectance spectroscopy. The anisotropic complex refractive index was measured from 7500 to 300 cm-1 (1.33 to 33.33 µm). The deduced anisotropic optical constants were found to be consistent with those previously reported. Once measured and validated, the optical constants were applied to model the pressed pellet reflectance spectrum. It was evident that an average of the anisotropic refractive indices was insufficient to account for the measured pellet reflectance. In order to account for contributions of all possible microcrystalline orientations within the pellet, the Python package PYELLI was used to calculate a basis set of orientation-dependent reflection spectra spanning the distinct ? and ? Euler rotations of the uniaxial crystal. When the population of orientations was allowed to vary freely in a spectral fit analysis, the fit-deduced orientations were tightly clustered along f = 45º, hinting at residual anisotropy in the pressed pellet sample. Conversely, an equally valid spectral fit (with marginally worse fit metric) was obtained when the population was constrained to an isotropic distribution of orientations. Subsequent non-zero cross-polarization reflectance measurements likewise suggested anisotropy in the pellet. However, both grazing incidence wide-angle x-ray scattering and scanning electron microscopy measurements revealed that the microcrystal orientations at the surface of the pressed pellet sample were isotropically distributed (and that the average crystallite size was larger than ?/10). Application of the measured complex refractive indices for modeling the reflectance spectrum of the pressed pellet, and rectification of these seemingly contradictory observations will be discussed.

Wilhelm, Michael J.↗
DOE OSTI2020

Multi-scale model based design of membrane reactor/separator processes for intensified hydrogen production through the water gas shift reaction

This paper aims to first quantify the impact of various diffusion models (Maxwell-Stefan, Wilke, Dusty-Gas) on the predictions of a multi-scale membrane reactor/separator mathematical model, and to then demonstrate this model's use for the design and process intensification of membrane reactor/separator systems for hydrogen production. This multi-scale model captures velocity, temperature and species' concentration profiles along the catalyst pellet's radial direction, and along the reactor's axial direction, by solving the momentum, energy, and species transport equations, accounting for convection, conduction, reaction, and diffusion mechanisms. In the first part of work, the effect of pellet-scale design parameters (mean pore diameter, volumetric porosity, tortuosity factor, etc.) and various species' flux models on the model predictions is studied. In the second part, the study focuses on the comparison, in terms of their process intensification characteristics, of various hydrogen production processes. These include a conventional high-temperature shift reactor (HTSR)/low-temperature shift reactor (LTSR) sequence, a novel HTSR/membrane separator (MS)/LTSR/MS sequence, and a process that involves low-temperature shift membrane reactors-LTSMR in a series.

08 HYDROGEN↗
DOE OSTI2021

Characterizing mechanical and microstructural properties of novel montmorillonite-rich polyethylene composites

Montmorillonite (MMT) clays are important industrial materials used as catalysts, chemical sorbents and fillers in polymer–clay nanocomposites. The layered structure of these clays has motivated research into further applications of these low-cost materials, including use as ion exchange media and solid-state ionic conductors. In these applications, the mechanical properties of MMT are key when considering long-term, reliable performance. Previous studies have focused on the mechanical properties of nanocomposites with MMT as the minority component or pure MMT thin films. In this work, the microstructure and mechanical properties of pure MMT and majority MMT/polyethylene composites pressed into dense pellets are examined. Characterization methods such as X-ray diffraction, atomic force microscopy and scanning electron microscopy together with nanoindentation reveal important structure–property relationships in the clay-based materials. Here, utilizing these techniques, we have discovered that MMT processing impacts the layered microstructure, chemical stability and, critically, the elastic modulus and hardness of bulk MMT samples. Particularly, the density of the pellets and the ordering of the clay platelets within them strongly influence the elastic modulus and hardness of the pellets. By increasing pressing force or by incorporating secondary components, the density, and therefore mechanical properties, can be increased. If the layered structure of the clay is destroyed by exfoliation, the mechanical properties will be compromised. Understanding these relationships will help guide new studies to engineer mechanically stable MMT-based materials for industrial applications.

36 MATERIALS SCIENCE↗
NASA NTRS2009

Engineered Structured Sorbents for the Adsorption of Carbon Dioxide and Water Vapor from Manned Spacecraft Atmospheres: Applications and Testing 2008/2009

This paper describes efforts to improve on typical packed beds of sorbent pellets by making use of structured sorbents and alternate bed configurations to improve system efficiency and reliability. The benefits of the alternate configurations include increased structural stability gained by eliminating clay bound zeolite pellets that tend to fluidize and erode, and better thermal control during sorption to increase process efficiency. Test results that demonstrate such improvements are described and presented.

Howard, David F.↗
DOE OSTI2021

The effects of electrically exploding gold bridgewires into inert and explosive powder beds

Abstract The particle velocity created in beds of both low-density inert sugar and explosive PETN as a function of distance from an exploding bridgewire was measured using optical velocimetry and a silvered PMMA window. As expected, more violent bridge-bursts (from a greater-stored-energy capacitive discharge unit) resulted in greater particle velocities and a better supported compaction wave in sugar. In all cases, ramp waves, not shocks, were observed in the inert sugar. Large window velocities were observed for very powerful bursts (up to 270 m/s), but bursts required for stochastic detonator operation conditions resulted in sugar/PMMA window velocities of only 8–10 m/s 0.85 mm from the bridge location. In contrast, after a distance of only 0.65 mm, a building shock wave was observed in PETN under both threshold and reliable firing conditions. Subsequently a hot-spot-driven shock-to-detonation (SDT) process was observed prior to full detonation. The measured buildup process accounts for $$\approx $$ ≈ 66% of the so-called excess transit time (ETT) between the observed and theoretical total function time for the particular exploding-bridge-wire (EBW) detonator studied. The remainder must occur in the powerful output pellet region. In contrast to a common understanding, the ETT is found to be a weak function of the discharge energy. Thus, the operation of the detonator after a bridge-burst energy-to-powder reaction transition process is found to be hot-spot-driven SDT in both the low- and high-density pellets.

45 MILITARY TECHNOLOGY, WEAPONRY, AND NATIONAL DEF↗
DOE OSTI2022

Yield stress and flow behavior of enzyme liquefied slurries from corn cobs and corn stover pellets

With the increase in population, the world will depend on renewable sources to meet the increasing energy needs. The use of lignocellulosic biomass as a renewable source has been proven efficient for conversion to cellulosic ethanol and capable of contributing to thresholds for energy demand while reducing greenhouse gases by 90% when compared with fossil fuels. However, limitations in feeding and flow within biorefineries is encountered when system plugging occurs due to biomass compaction and a high yield stress for slurries formed during its processing, thereby preventing transport of biomass materials between plant unit operations. In some cases, this leads to unexpected plant shutdowns increasing industrial operational costs. As an alternative, enzyme-assisted liquefaction for slurry creation from corn stover at solids loadings up to 30% is reported in this work. Two different kinds of biomass (pelleted corn stover and cobs) were liquefied in a fed-batch process using commercial enzymes Celluclast 1.5L or Ctec-2 at 1FPU or 3 FPU per gram of dry solids in 10 mM sodium citrate buffer solution (pH 4.8). Pellets were fed into a 1 L stirred bioreactor according to a pre-defined fed-batch protocol over the first 5 hours until reaching 30% of solids loading. After 6, 24 and 96 hours, samples were taken and characterized with respect to their sugar composition, rheology and water absorption. Successful slurry creation with dramatically reduced yield stress was achieved for corn stover for both assessed enzymes. Yield stresses of 178±7 Pa (3 FPU, Celluclast 1.5L) and 79±6 Pa (3 FPU, Ctec-2) were measured for corn stover at 24 hours, compared to 6,000 Pa for samples without enzyme. Yield stress was 155± 29 Pa (3FPU, Ctec-2) and 257 ± 72 Pa (1 FPU,Celluclast 1.5L) for corn cobs at 24 hours. Yield stress decreased when residence time increased with an enhanced fluidity noted for higher enzyme concentrations. A profile for 6, 24 and 96h of yield stress measurements is presented.

Guitierrez, Diana↗
NASA NTRS1980

Silicon web process development

A barrier crucible design which consistently maintains melt stability over long periods of time was successfully tested and used in long growth runs. The pellet feeder for melt replenishment was operated continuously for growth runs of up to 17 hours. The liquid level sensor comprising a laser/sensor system was operated, performed well, and meets the requirements for maintaining liquid level height during growth and melt replenishment. An automated feedback loop connecting the feed mechanism and the liquid level sensing system was designed and constructed and operated successfully for 3.5 hours demonstrating the feasibility of semi-automated dendritic web growth. The sensitivity of the cost of sheet, to variations in capital equipment cost and recycling dendrites was calculated and it was shown that these factors have relatively little impact on sheet cost. Dendrites from web which had gone all the way through the solar cell fabrication process, when melted and grown into web, produce crystals which show no degradation in cell efficiency. Material quality remains high and cells made from web grown at the start, during, and the end of a run from a replenished melt show comparable efficiencies.

Duncan, C. S.↗
DOE OSTI2025

Fracture toughness measurement of ceramics with fuel pellet geometry

The crack initiation of nuclear fuel pellets, driven by extreme temperature gradients, is a critical factor impacting reactor performance. Although this fact is widely acknowledged, there is limited fracture toughness data for specimens with representative geometry and fabricated using relevant processing methods. Here, to address this, a new chevron-notched short-rod specimen configuration with diameter and length both equal to 10 mm, representative of a conventional fuel pellet and tested in tension, was developed in an attempt to validly measure Mode I fracture toughness, K Ic . Test calibration was carried out by testing polycrystalline ZrO 2 , SiC, and Si 3 N 4 ceramics fabricated with conventional fuel pellet geometry and known fracture toughnesses. The results suggest that the method described in this paper produces valid K Ic measurements using conventional ceramic fuel pellets.

Ceramics↗
DOE OSTI2021

Degradation Comparison of Cyclic and Linear Siloxane Contamination on Solid Oxide Fuel Cells Ni-YSZ Anode

The solid oxide fuel cell (SOFC) nickel-yttria stabilized zirconia (Ni-YSZ) anode degradation due to different types of siloxane contamination is investigated. A cyclic structure siloxane, octamethylcyclotetrasiloxane (D4), and a linear structure siloxane, decamethyltetrasiloxane (L4), are mixed with H 2 +N 2 as the fuel for SOFCs at 750°C. The electrochemical characterization results after stability experiments suggest that the SOFC contaminated with cyclic siloxane, D4, had higher degradation. Pure YSZ pellets with different surface hydroxylation extents were also tested to investigate the D4/L4 adsorption and deposition process. Postmortem SEM/WDS, XRD and Raman analysis all indicate that cyclic siloxane has more deposition than linear siloxane on the anode. Further analysis demonstrates that high adsorption and low desorption rates of cyclic siloxane on YSZ are linked to the degradation. Besides the silicon deposition, SiC and amorphous carbon deposition were also observed from the XRD and Raman analysis.

25 ENERGY STORAGE↗
NASA NTRS1984

Sampling of Silicon Powder for Impurity Analysis

Electron beam forms dense pellets of powdered silicon for Zeeman analysis. Sampling method focuses electron beam on submicron silicon powder. Process enhances quality control in production of low-cost silicon powder for semiconductor industry.

Yamakawa, K. A.↗
DOE OSTI2020

Hot Water Extraction: Short Rotation Willow, Mixed Hardwoods, and Process Considerations

Short rotation woody crops (SRWC) like shrub willow are highly productive biomass resources of interest for energy and fuel applications. Hot water extraction (HWE) as an upgrading tool to enable the use of willow biomass in pellet applications has been proposed, and is of increasing interest. This study treats willow and mixes of willow and conventional mixed hardwood feedstock with HWE in a tumbling laboratory reactor to elucidate the effects of time, temperature, feedstock mixes, and other process considerations (water:biomass ratio, presteaming, counter-current processing) on mass removals and other extraction outcomes (e.g., sugar, acetate, and furan yields). Results demonstrated alignment of extraction outcomes with P-factor from 155 °C to 175 °C, with a good compromise of removed mass and co-product potential in the range from 575–800 P-factor. The preferred condition was chosen as 575 P-factor. HWE of mixes of willow and hardwood feedstocks showed a linear response of extraction outcomes to willow:hardwood ratios. Testing of water:biomass ratios demonstrated that this is a significant consideration, with each outcome being affected somewhat differently, and indicating that HWE is more diffusion dependent than expected. Presteaming shows little to no effect on extraction outcomes, while multi-stage cooks simulating counter-current operation indicate a significant potential value in counter-current extraction.

09 BIOMASS FUELS↗
DOE OSTI2025

Effects of dose rate on the microstructure and deuterium retention in γ-LiAlO 2 pellets

This report presents experimental findings obtained from November 2024 to September 2025. Defect accumulation and microstructural evolution during ion irradiation at elevated temperatures are governed by two competing processes: defect production, driven by dose rate, and defect recovery, controlled by defect diffusion, interaction, and annihilation. At a given dose, the resulting microstructural evolution depends on both the dose rate and irradiation temperature. As a continuation of our FY24 tritium science project, which investigated temperature effects at a fixed dose rate, this study focuses on dose-rate effects at a fixed temperature to provide deeper insights into the irradiated microstructure and compositional changes in γ-LiAlO 2 pellets. The study aims to elucidate the impact of dose rate on microstructure, precipitate morphology, deuterium retention, and lithium volatility in γ-LiAlO 2 pellets under sequential 120 keV He + and 80 keV D 2 + ion irradiation. Three dose rates of 7.3×10 4 , 2.9×10 4 and 6.8×10 5 dpa/s were applied to achieve the same total ion fluence of 2×10 17 (He + +D + )/cm 2 at 500 °C, corresponding to a maximum combined dose of 7.55 dpa at ~255 nm. The irradiated pellets were subsequently characterized using scanning transmission electron microscopy (STEM) and time-of-flight secondary ion mass spectrometry (ToF-SIMS). The microstructural response of γ-LiAlO 2 to ion irradiation was found to be strongly dose-rate dependent. At medium and high dose rates, irradiation produced a surface amorphized layer and an underlying crystalline layer containing LiAl 5 O 8 precipitates, with implanted gases accumulating and forming blisters at the crystalline-amorphous interface. It remains to be investigated whether the amorphized layer was produced by He + ion irradiation prior to D 2 + ion irradiation. In contrast, at low dose rates, the material remained crystalline, with cavities, likely gas-filled, distributed around precipitates, within the γ-LiAlO 2 matrix, and along grain boundaries. While precipitate morphology exhibited anisotropy, their size showed little sensitivity to dose rate in the applied range of this study. This result, however, does not rule out the possibility that further reductions in dose rate could influence precipitate size. High dose-rate irradiation enhanced protonium–deuterium isotopic exchange and lithium depletion in the amorphized region. Collectively, the results show that dose rate governs amorphization, gas redistribution, isotopic exchange, and lithium depletion, providing important insights into the mechanisms underlying structural evolution in γ-LiAlO 2 pellets under reactor-relevant irradiation conditions.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2022

Effect of Remnant Carbon and Etching of Particles on Pyrolysis Bonded Silicon Carbide (PBSC)

Silicon carbide (SiC) formed through pyrolysis of preceramic polymers loaded with SiC particles has gained significant attention for applications such as coatings, composite matrix modifications, and most importantly additive manufacturing. This work presents combined synchrotron XRD, Raman spectroscopy, scanning electron microscopy, nano-indentation, and Vickers indentation of pyrolysis bonded SiC to shed light on the changes of composition and mechanical properties of these materials. Characterization was performed on samples that were heat treated ranging from the synthesis 850 °C up to 1500 °C. Pre-treatments of the powders prior to pellet synthesis, such as heat treatment and etching using a hydrofluoric acid (HF), were investigated. It is shown that the degradation of mechanical properties when exposed to higher temperatures is due to the burnout of amorphous carbon clusters remnant of the pyrolysis process of the preceramic polymer. Furthermore, prior HF etching and removal of the native oxide layer of the powders showed improved density and hardness values in the final pellets. The average Vickers hardness of the control samples were 4.59 GPa and later 3.74 GPa when exposed to 1500 °C, while the samples synthesized using powders that were etched with HF had an average hardness value of 9.37 GPa and later 6.86 GPa when exposed to 1500 °C.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
DOE OSTI2021

Integration of Air Classification and Hydrothermal Carbonization to Enhance Energy Recovery of Corn Stover

Air classification (AC) is a cost-effective technology that separates the energy-dense light ash fraction (LAF) from the inorganic-rich high ash fraction (HAF) of corn stover. HAF could be upgraded into energy-dense solid fuel by hydrothermal carbonization (HTC). However, HTC is a high-temperature, high-pressure process, which requires additional energy to operate. In this study, three different scenarios (i.e., AC only, HTC only, and integrated AC–HTC) were investigated for the energy recovery of corn stover. AC was performed on corn stover at an 8 Hz fan speed, which yielded 84.4 wt. % LAF, 12.8 wt. % HAF, and 2.8 wt. % below screen particles. About 27 wt. % ash was reduced from LAF by the AC process. Furthermore, HTC was performed on raw corn stover and the HAF of corn stover at 200, 230, and 260 °C for 30 min. To evaluate energy recovery, solid products were characterized in terms of mass yield, ash yield, ultimate analysis, proximate analyses, and higher heating value (HHV). The results showed that the energy density was increased with the increase in HTC temperature, meanwhile the mass yield and ash yield were decreased with the increase in HTC temperature. Proximate analysis showed that fixed carbon increased 18 wt. % for original char and 27 wt. % for HAF char at 260 °C, compared to their respective feedstocks. Finally, the hydrochar resulting from HAF was mixed with LAF and pelletized at 180 bar and 90 °C to densify the energy content. An energy balance of the integrated AC–HTC process was performed, and the results shows that integrated AC with HTC performed at 230 °C resulted in an additional 800 MJ/ton of energy recovery compared to the AC-only scenario.

09 BIOMASS FUELS↗
NASA NTRSDate not supplied

Plasma Assisted Nutrient Recovery from Inedible Biomass via Ash Leaching

Sustaining a human presence on the Moon, Mars, or deep space will require closing loops on many life support systems. Some form of agriculture will be required because plants produce the vitamins, antioxidants, and essential oils in our diets that degrade over time in stored foods. In addition, they provide dietary fiber, revitalize air and purify water. It is estimated that 93 kg of plant nutrients are required to support one crew member per year. Growing plants will require recycling nutrients trapped in inedible plant stems, leaves and debris. We examined the effects of using thermal plasma and various carrier gases to breakdown inedible plant biomass and aid in nutrient recovery. Previous work demonstrated a thermally degrading environment such as a muffle furnace improved nutrient recovery from inedible biomass prior to an acid leaching process, however, a muffle furnace is an inefficient process. We tested the ability of a small scale, thermal plasma using carbon dioxide, nitrogen, or air as plasma carrier gases to degrade pelleted plant biomass. The gases were chosen to explore variations in recovery and potential chemical by-products. Plasma treated and untreated biomass was leached with different concentrations of acid to determine the extraction of nutrients (potassium, magnesium, calcium, and. phosphorus) for reuse in the crop production cycle. Results are presented showing the impact of plasma processing prior to acid leaching on recovery of plant nutrients.

Plasma↗