Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “PBX 9502”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8

Quantifying CTFE content in FK-800 using ATR-FTIR and time to peak crystallization

The chlorotrifluoroethylene (CTFE) content in vinylidene fluoride (VDF)-CTFE copolymers greatly influences the chemical and physical properties and ultimately determines the application. The copolymer known as FK-800 has a VDF:CTFE ratio of ~1:3 and is used almost exclusively as the binder in the insensitive high explosive (HE) formulation PBX 9502. Due to the dangerous nature of HE work and the effect CTFE content variations have, the ability to quickly and easily quantify CTFE content is of interest. Two techniques, attenuated total reflectance-Fourier transform infrared spectroscopy (ATR-FTIR) and time to peak crystallization measured by heat flow calorimetry, were evaluated here as potential means for quantifying CTFE content. Based on the certificate of analyses (COAs), FK-800 lots with varied CTFE content encompassing the range historically used in HE applications were used as standards for both methodologies. For FTIR, a linear regression was performed on the peak area of the C-Cl IR stretch and the CTFE content; the methodology was then demonstrated on four samples, two lots of unadulterated material and material recovered from two HE samples. The calculated CTFE content and COAs were in good agreement for all four samples. Heat flow calorimetry revealed the relationship between time to peak crystallization and CTFE content was best fit by a power regression; the methodology was then tested on two different FK-800 lots. Only one sample showed good agreement between the calculated CTFE content and the COA. This discrepancy indicates the method developed is not suitable for quantifying CTFE, but provides valuable insight regarding the crystallization behavior of VDF-CTFE copolymers.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Continuous wave laser irradiation of explosives

Quantitative measurements of the levels of continuous wave (CW) laser light that can be safely applied to bare explosives during contact operations were obtained at 532 nm, 785 nm, and 1550 nm wavelengths. A thermal camera was used to record the temperature of explosive pressed pellets and single crystals while they were irradiated using a measured laser power and laser spot size. A visible light image of the sample surface was obtained before and after the laser irradiation. Laser irradiation thresholds were obtained for the onset of any visible change to the explosive sample and for the onset of any visible chemical reaction. Deflagration to detonation transitions were not observed using any of these CW laser wavelengths on single crystals or pressed pellets in the unconfined geometry tested. Except for the photochemistry of DAAF, TATB and PBX 9502, all reactions appeared to be thermal using a 532 nm wavelength laser. For a 1550 nm wavelength laser, no photochemistry was evident, but the laser power thresholds for thermal damage in some of the materials were significantly lower than for the 532 nm laser wavelength. No reactions were observed in any of the studied explosives using the available 300 mW laser at 785 nm wavelength. Tables of laser irradiance damage and reaction thresholds are presented for pressed pellets of PBX9501, PBX9502, Composition B, HMX, TATB, RDX, DAAF, PETN, and TNT and single crystals of RDX, HMX, and PETN for each of the laser wavelengths.

45 MILITARY TECHNOLOGY, WEAPONRY, AND NATIONAL DEF↗

xRage: HE Initiation Models

The xRage code contains three HE ignition models: Forest Fire, Cerro Grande and Ignition and Growth. After describing these models we present results of verification and validation (V and V) tests. These include simulations to determine the Pop-plot for each model and comparision with embedded velocity gauge data for shock-to-detonation transition (SDT) experiments. The data for the SDT experiments on PBX 9502 is taken from the recently developed high explosive database (HED). The HED data files contains additional meta-data with the key experimental parameters. This enables the use of scripts to automate testing: generating xRage input file, running simulation and generating comparison plots with experimental and simulated data. The simulations show that the models are robust. But there is a mesh dependence with the time for transition-to-detonation varying by several tenths of microseconds. After the transition to a detonation wave, the detonation speed and pressure may vary by a few per cent.

36 MATERIALS SCIENCE↗

Effect of pressure vents on the fast cookoff of energetic materials.

The effect of vents on the fast cookoff of energetic materials is studied through experimental modifications to the confinement vessel of the Radiant Heat Fast Cookoff Apparatus. Two venting schemes were investigated: 1) machined grooves at the EM-cover plate interface; 2) radial distribution of holes in PEEK confiner. EM materials of PBXN-109 and PBX 9502 were tested. Challenges with the experimental apparatus and EM materials were identified such that studying the effect of vents as an independent parameter was not realized. The experimental methods, data and post-test observations are presented and discussed.

Cooper, Marcia A.↗

The Thermal Response of TATB-Based PBXs

In the design mode of operation, TATB-­based PBXs, such as PBX 9502 or LX-­17, are promptly initiated by a detonator and booster system. In abnormal situations, such as accidents, a wide variety of non-­design-­mode insults can arise and it is desirable that these do not produce detonation but rather that, at most, they lead to a low chemical energy release. The most significant abnormal hazard is the direct shock initiation threat arising from high-­velocity fragment impact. This is quite well defined and may result in a detonative response if the fragment is large enough and fast enough. However, it is of considerably greater significance to the safety envelope of these explosives whether they are at all capable of DDT (deflagration-­to-­detonation transition), either at ambient or elevated temperatures since accidental insults to the explosive, either mechanical or thermal, that may produce local burning are both more numerous and more likely than shock loading. The purpose of this document is to demonstrate, based on the accumulated body of conservative experimental testing, that in explosive geometries and masses relevant to the Weapons Program, TATB-­based PBXs do not present a deflagration-­to-­detonation transition (DDT) hazard at any temperature. This is a significant statement since it removes detonative outcome concerns from the majority of insult scenarios on TATB-­based charges. It does not address the response of included detonator and booster assemblies, the response of which must be considered separately.

36 MATERIALS SCIENCE↗

LIHEM Failure Model Development

Previously, a factor of safety criterion for the IHEs (LX-17 and PBX 9502) was defined using the ultimate strength of the material based on uniaxial compression and tension data at various temperatures and strain rates and an experimentally derived failure surface. The probability of failure was subsequently calculated using this factor of safety, uncertainty data, and assumptions. This year, the methodology was extended to incorporate the effect of cyclic loading into the Livermore Insensitive High Explosives Mechanical (LIHEM) model. As mentioned in the previous section, we performed cyclic experiments on three-point-bend specimens in order to find cycles-to-failure as a function of failure load at various temperatures, frequencies, and amplitudes.

42 ENGINEERING↗

Shock-to-detonation transition simulations

Shock-to-detonation transition (SDT) experiments with embedded velocity gauges provide data that can be used for both calibration and validation of high explosive (HE) burn models. Typically, a series of experiments is performed for each HE in which the initial shock pressure is varied. Here we describe a methodology for automating a series of SDT simulations and comparing numerical tracer particle velocities with the experimental gauge data. Illustrative examples are shown for PBX 9502 using the HE models implemented in the xRage ASC code at LANL.

45 MILITARY TECHNOLOGY, WEAPONRY, AND NATIONAL DEF↗

Numerical computation of Pop plot

The Pop plot — distance-of-run to detonation versus initial shock pressure — is a key characterization of shock initiation in a heterogeneous explosive. Reactive burn models for high explosives (HE) must reproduce the experimental Pop plot to have any chance of accurately predicting shock initiation phenomena. This report describes a methodology for automating the computation of a Pop plot for a specific explosive with a given HE model. Illustrative examples of the computation are shown for PBX 9502 with three burn models (SURF, WSD and Forest Fire) utilizing the xRage code, which is the Eulerian ASC hydrocode at LANL. Comparison of the numerical and experimental Pop plot can be the basis for a validation test or as an aid in calibrating the burn rate of an HE model. Issues with calibration are discussed.

45 MILITARY TECHNOLOGY, WEAPONRY, AND NATIONAL DEF↗

Verification test of the SURF and SURFplus models in xRage

As a verification test of the SURF and SURFplus models in the xRage code we use a propagating underdriven detonation wave in 1-D. This is about the only test cases for which an accurate solution can be determined based on the theoretical structure of the solution. The solution consists of a steady ZND reaction zone profile joined with a scale invariant rarefaction or Taylor wave and followed by a constant state. The end of the reaction profile and the head of the rarefaction coincide with the sonic CJ state of the detonation wave. The constant state is required to match a rigid wall boundary condition. For a test case, we use PBX 9502 with the same EOS and burn rate as previously used to test the shock detector algorithm utilized by the SURF model. The detonation wave is propagated for 10 μs (slightly under 80mm). As expected, the pointwise errors are largest in the neighborhood of discontinuities; pressure discontinuity at the lead shock front and pressure derivative discontinuities at the head and tail of the rarefaction. As a quantitative measure of the overall accuracy, the L2 norm of the difference of the numerical pressure and the exact solution is used. Results are presented for simulations using both a uniform grid and an adaptive grid that refines the reaction zone.

45 MILITARY TECHNOLOGY, WEAPONRY, AND NATIONAL DEF↗

Verification Test of the SURF and SURFplus Models in xRage: Part II

The previous study used an underdriven detonation wave (steady ZND reaction zone profile followed by a scale invariant rarefaction wave) for PBX 9502 as a validation test of the implementation of the SURF and SURFplus models in the xRage code. Even with a fairly fine uniform mesh (12,800 cells for 100mm) the detonation wave profile had limited resolution due to the thin reaction zone width (0.18mm) for the fast SURF burn rate. Here we study the effect of finer resolution by comparing results of simulations with cell sizes of 8, 2 and 1 μm, which corresponds to 25, 100 and 200 points within the reaction zone. With finer resolution the lead shock pressure is closer to the von Neumann spike pressure, and there is less noise in the rarefaction wave due to fluctuations within the reaction zone. As a result the average error decreases. The pointwise error is still dominated by the smearing the pressure kink in the vicinity of the sonic point which occurs at the end of the reaction zone.

97 MATHEMATICS AND COMPUTING↗

Verification Test of the SURF and SURFplus Models in xRage: Part III Affect of Mesh Alignment

The previous studies used an underdriven detonation wave in 1-dimension (steady ZND reaction zone profile followed by a scale-invariant rarefaction wave) for PBX 9502 as a verification test of the implementation of the SURF and SURFplus models in the xRage code. Since the SURF rate is a function of the lead shock pressure, the question arises as to the effect on accuracy of variations in the detected shock pressure due to the alignment of the shock front with the mesh. To study the effect of mesh alignment we simulate a cylindrically diverging detonation wave using a planar 2-D mesh. The leading issue is the magnitude of azimuthal asymmetries in the numerical solution. The 2-D test case does not have an exact analytic solution. To quantify the accuracy, the 2-D solution along rays through the origin are compared to a highly resolved 1-D simulation in cylindrical geometry.

97 MATHEMATICS AND COMPUTING↗

Development and Execution of a Large-scale DDT Tube Test for IHE Material Qualification

Insensitive High Explosive (IHE) Materials are defined in Chapter IX of the DOE Explosive Safety Standard (DOE-STD-1212-2012) as being materials that are massdetonable explosives that are so insensitive that the probability of accidental initiation or transition from burning to detonation is negligible1. There are currently a number of tests included in the standard that are required to qualify a material as IHE, however, none of the tests directly evaluate for the transition from burning to detonation (aka deflagration-to-detonation transition, DDT). Currently, there is a DOE complex-wide effort to revisit the IHE definition in DOE-STD-1212-2012 and change the qualification requirements. The proposal lays out a new approach, requiring fewer, but more appropriate tests, for IHE Material qualification. One of these new tests is the Deflagration-to-Detonation Test. According to the redefinition proposal, the purpose of the new deflagration-todetonation test is “to demonstrate that an IHE material will not undergo deflagration-to-detonation under stockpile relevant conditions of scale, confinement, and material condition. Inherent in this test design is the assumption that ignition does occur, with onset of deflagration. The test design will incorporate large margins and replicates to account for the stochastic nature of DDT events.” In short, the philosophy behind this approach is that if a material fails to undergo DDT in a significant over-test, then it is extremely unlikely to do so in realistic conditions. This effort will be valuable for the B61 LEP to satisfy their need qualify the new production lots of PBX 9502. The work described in this report is intended as a preliminary investigation to support the proposed design of an overly conservative, easily fielded DDT test for updated IHE Material Qualification standard. Specifically, we evaluated the aspects of confinement, geometry, material morphology and temperature. We also developed and tested a thermally robust igniter system.

36 MATERIALS SCIENCE↗

Fine Tuning the CJ Detonation Speed of a High Explosive products Equation of State

For high explosive (HE) simulations, inaccuracies of a per cent or two in the detonation wave speed can result from not suficiently resolving the reaction zone width or from small inaccuracies in calibrating the products equation of state (EOS) or from variation of HE lots. More accurate detonation speeds can be obtained by ne tuning the equation of state to compensate. Here we show that two simple EOS transformations can be used to adjust the CJ detonation speed by a couple of per cent with minimal effect on the CJ release isentrope. The two transformations are (1) a shift in the energy origin and (2) a linear scaling of the speci c volume. The effectiveness of the transformations is demonstrated with simulations of the cylinder test for PBX 9502 starting with a products EOS for which the CJ detonation speed is 1 per cent too low.

45 MILITARY TECHNOLOGY, WEAPONRY, AND NATIONAL DEF↗

A Preliminary Assessment of the SURF Reactive Burn Model Implementation in FLAG

Properly validated and calibrated reactive burn models (RBM) can be useful engineering tools for assessing high explosive performance and safety. Experiments with high explosives are expensive. Inexpensive RBM calculations are increasingly relied on for predictive analysis for performance and safety. This report discusses the validation of Menikoff and Shaw’s SURF reactive burn model, which has recently been implemented in the FLAG code. The LANL Gapstick experiment is discussed as is its’ utility in reactive burn model validation. Data obtained from pRad for the LT-63 series is also presented along with FLAG simulations using SURF for both PBX 9501 and PBX 9502. Calibration parameters for both explosives are presented.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Model comparisons of the reactive burn model SURF in three ASC codes

A study of the SURF reactive burn model was performed in FLAG, PAGOSA and XRAGE. In this study, three different shock-to-detonation transition experiments were modeled in each code. All three codes produced similar model results for all the experiments modeled and at all resolutions. Buildup-to-detonation time, particle velocities and resolution dependence of the models was notably similar between the codes. Given the current PBX 9502 equations of state and SURF calibrations, each code is equally capable of predicting the correct detonation time and distance when impacted by a 1D impactor at pressures ranging from 10-16 GPa, as long as the resolution of the mesh is not too coarse.

45 MILITARY TECHNOLOGY, WEAPONRY, AND NATIONAL DEF↗

Preliminary IHE Qualification of a PATO/Viton-A Formulation: Shock-to-Detonation Experiments

All nuclear weapons in the stockpile require high explosive (HE) components to function. These explosives create safety hazards during storage, handling, and stockpile maintenance operations, where unintentional initiation can cause serious injuries, death, or significant damage to facilities and the environment. To mitigate these risks, the explosive formulation(s) used in these components should be as resistant to accidental initiation as possible. Mass-detonable explosives that are “so insensitive that the probability of accidental initiation or transition from burning to detonation is negligible” are defined by Chapter IX of the DOE Explosive Safety Standard as insensitive high explosives (IHE). The IHE in most common use in the DOE is currently PBX 9502 (95%wt TATB, 5%wt Kel-F800). The Los Alamos and Lawrence Livermore National Laboratories have established a series of experiments used to classify new HE formulations as either conventional HE (CHE) or IHE. This report describes three sets of gas gun experiments on a new candidate IHE formulation consisting of 95.5%wt 3-Picrylamino-1,2,4-Triazole (PATO) and 4.5%wt Viton-A. These experiments provide a preliminary evaluation of the performance of this material on the shock-to-detonation (SDT) portion of this qualification standard.

3-Picrylamino-1,2,4-Triazole↗

SURF Model Resolution in xRage Code

A key issue for detonation wave simulations with a reactive burn model is the resolution needed for the reaction zone. The reaction-zone width is a physical length scale. For plastic-bonded explosives, it is small (on the order of 100 microns) but affects important detonation properties such as the detonation speed. Even with adaptive mesh refinement, a well resolved reaction zone is computationally expensive. Here we consider the trade-off between computational expense and accuracy when the resolution of the reaction zone is varied for simulations with the xRage code of PBX 9501 with the SURF burn model and of PBX 9502 with the SURFplus burn model. For assessing shock initiation, the numerical Pop plot is simulated, and for assessing propagating detonation waves, the cylinder test is used as a test problem. The reaction-zone resolution is varied from a cell size of 6.25 to 200 microns, and key properties of the solutions are compared. With 6 micron resolution, the numerical solution is near mesh converged and can be used to judge the accuracy of the coarser resolution simulations. For the propagating detonation wave in the cylinder test, at 200 microns the detonation speed is low by a couple of per cent. In terms of cpu-hours, the finest resolution is about a factor of 100 more expensive than the coarsest resolution.

45 MILITARY TECHNOLOGY, WEAPONRY, AND NATIONAL DEF↗

Accuracy of High Explosive Data used for Reactive Burn Model Calibration

Reactive burn models for a high explosive (HE) have three components: an equation of state (EOS) for the products, an EOS for the reactants and a reaction rate. For the products, we discuss the uncertainty in data for the planar detonation state and its release isentrope. For the reactants, the uncertainty in the principal shock locus data is discussed. For the reaction rate, we discuss uncertainties in shock initiation data (distance-of-run to detonation as a function of shock pressure), and curvature effect data (detonation speed as a function of front curvature). An important source of uncertainty for calibrating the reaction rate for a plastic-bonded explosive (PBX) results from variations in heterogeneities; that is the mesoscale structure of HE grains, binder and porosity. This shows up in the scatter of both shock initiation data and curvature effect data with small changes in initial density and initial temperature, and systematic changes with PBX lot. As illustrative examples, we use data for the conventional HMX based PBX 9501 and the insensitive TATB based PBX 9502 since these explosives have been extensively studied and high quality data are readily available in the literature.

45 MILITARY TECHNOLOGY, WEAPONRY, AND NATIONAL DEF↗