Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Neutron Leakage”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Comparison of NMC estimates with trans-stilbene, EJ-309, and He-3 detection systems

Neutron multiplicity counting (NMC) is a technique for the assay of fissile material. In this work, three detection systems are utilized for active interrogation assay of shells of the Rocky Flats shells (highly enriched uranium, 93% 235U) stacked from 13.25-54.92 kg assemblies. The singles ($R_1$) and doubles ($R_2$) rates are calculated with each system to estimate two sample parameters: $M_L$- the leakage multiplication and F - the sample fission rate. The estimated mass, m, is found by dividing F by a constant activity per unit mass. Since we are interrogating HEU, the α ratio of (α; n) to fission neutrons is taken to be zero. The system of equations to calculate these quantities was originally derived. The Neutron Multiplicity 3 He Array Detector (NOMAD) consists of 15 3 He tubes inside polyethylene and is the traditional, capture-based detection system for NMC. The polyethylene moderates incoming neutrons for thermal capture in individual tubes. The low gamma background, discrete capture signals, and high efficiency of the NOMAD are beneficial for NMC. However, the time to slow down neutrons to thermal energies leads to a system die away time on the scale of microseconds. Comparatively, the Rossi-alpha Measurements – Rapid Organic (n, γ) Discrimination Detector (RAMRODD) and the Organic Scintillator Array (OSCAR) are scatter-based detection systems. RAMRODD consists of 8, 5.08 by 5.08 cm EJ-309 liquid scintillators in 4 pairs, evenly-spaced with 90 degrees separation about the center of each assembly. OSCAR consists of a single array of 12, 5.08 by 5.08 cm trans-stilbene crystals aligned with the center of the assembly. Scatter-based systems detect fast neutrons without any moderation, leading to system die away times on the scale of tens of nanoseconds. This allows much shorter timing gate widths compared to thermal systems, thus increasing counting statistics of true correlated fission events. However, scatter-based systems are susceptible to neutron cross-talk when an incident neutron scatters off one detector and interacts in an adjacent detector, causing two seemingly correlated detection signals. The equations developed adjust for cross-talk to conduct NMC with scatter-based systems.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
DOE OSTI2021

Implementation of Monte Carlo Transport in the General Relativistic SpEC Code

Neutrino transport and neutrino-matter interactions are known to play an important role in the evolution of neutron star mergers and of their post-merger remnants. Neutrinos cool remnants, drive post-merger winds, and deposit energy in the low-density polar regions where relativistic jets may eventually form. Neutrinos also modify the composition of the ejected material, impacting the outcome of nucleosynthesis in merger outflows and the properties of the optical/infrared transients that they power (kilonovae). So far, merger simulations have largely relied on approximate treatments of the neutrinos (leakage, moments) that simplify the equations of radiation transport in a way that makes simulations more affordable but also introduces unquantifiable errors in the results. To improve on these methods, we recently published a first simulation of neutron star mergers using a low-cost Monte Carlo algorithm for neutrino radiation transport. Our transport code limits costs in optically thick regions by placing a hard ceiling on the value of the absorption opacity of the fluid, yet all approximations made within the code are designed to vanish in the limit of infinite numerical resolution. We provide here an in-depth description of this algorithm, of its implementation in the SpEC merger code, and of the expected impact of our approximations in optically thick regions. We argue that the last is a subdominant source of error at the accuracy reached by current simulations and for the interactions currently included in our code. We also provide tests of the most important features of this code.

79 ASTRONOMY AND ASTROPHYSICS↗
DOE OSTI2023

Neutrino transport in general relativistic neutron star merger simulations

Abstract Numerical simulations of neutron star–neutron star and neutron star–black hole binaries play an important role in our ability to model gravitational-wave and electromagnetic signals powered by these systems. These simulations have to take into account a wide range of physical processes including general relativity, magnetohydrodynamics, and neutrino radiation transport. The latter is particularly important in order to understand the properties of the matter ejected by many mergers, the optical/infrared signals powered by nuclear reactions in the ejecta, and the contribution of that ejecta to astrophysical nucleosynthesis. However, accurate evolutions of the neutrino transport equations that include all relevant physical processes remain beyond our current reach. In this review, I will discuss the current state of neutrino modeling in general relativistic simulations of neutron star mergers and of their post-merger remnants. I will focus on the three main types of algorithms used in simulations so far: leakage, moments, and Monte-Carlo scheme. I will review the advantages and limitations of each scheme, as well as the various neutrino–matter interactions that should be included in simulations. We will see that the quality of the treatment of neutrinos in merger simulations has greatly increased over the last decade, but also that many potentially important interactions remain difficult to take into account in simulations (pair annihilation, oscillations, inelastic scattering).

Foucart, Francois (ORCID:0000000346174738)↗
NASA NTRS1977

Annual Conference on Nuclear and Space Radiation Effects, 14th, College of William and Mary, Williamsburg, Va., July 12-15, 1977, Proceedings

Topics related to processing and hardness assurance are considered, taking into account the radiation hardening of CMOS technologies, technological advances in the manufacture of radiation-hardened CMOS integrated circuits, CMOS hardness assurance through process controls and optimized design procedures, the application of operational amplifiers to hardened systems, a hard off-the-shelf SG1524 pulse width modulator, and the gamma-induced voltage breakdown anomaly in a Schottky diode. Basic mechanisms are examined, giving attention to chemical and structural aspects of the irradiation behavior of SiO2 films on silicon, experimental observations of the chemistry of the SiO2/Si interface, leakage current phenomena in irradiated SOS devices, the avalanche injection of holes into SiO2, the low-temperature radiation response of Al2O3 gate insulators, and neutron damage mechanisms in silicon at 10 K. Other subjects discussed are related to radiation effects in devices and circuits, space radiation effects, and aspects of simulation, energy deposition, and dosimetry.

Stahl, R. H.↗
DOE OSTI2022

Improving Effective Mass Estimations in Pu-Metal Annuli

Determining the effective mass of 240 Pu in a plutonium metal item can be achieved through a number of destructive and non-destructive assay techniques. However, these techniques have one or more shortcomings. These include the need for large quantities of plutonium, long measurement time, or lack of sufficient accuracy. While efforts have been made to mitigate these issues by estimating 240 Pu quantities through neutron coincidence counting techniques, these estimates are subject to systematic bias, and their estimates are not well characterized when other factors of the annulus’ physical form and composition are accounted for. In this work, we expand upon these non-destructive assay techniques via the implementation of random forest machine learning models, which produce correction functions that augment and improve the effective mass estimates derived from classical leakage multiplication, singles, doubles, and triples multiplicity counting equations.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
DOE OSTI2023

Evaluation of HPK n + - p planar pixel sensors for the CMS Phase-2 upgrade

To cope with the challenging environment of the planned high luminosity upgrade of the Large Hadron Collider (HL-LHC), scheduled to start operation in 2029, CMS will replace its entire tracking system. The requirements for the tracker are largely determined by the long operation time of 10 years with an instantaneous peak luminosity of up to 7.5 × 10 34 cm –2 s –1 in the ultimate performance scenario. Depending on the radial distance from the interaction point, the silicon sensors will receive a particle fluence corresponding to a non-ionizing energy loss of up to $\Phi_{\text {eq}}$ = 3.5 × 10 16 cm –2 . Here this paper focuses on planar pixel sensor design and qualification up to a fluence of $\Phi_{\text {eq}}$ = 1.4 × 10 16 cm –2 . For the development of appropriate planar pixel sensors an R&D program was initiated, which includes $n^+ -p$ sensors on 150 mm (6”) wafers with an active thickness of 150 μm with pixel sizes of 100 × 25 μm 2 and 50 × 50 μm 2 manufactured by Hamamatsu. Single chip modules with ROC4Sens and RD53A readout chips were made. Irradiation with protons and neutrons, as well was an extensive test beam campaign at DESY were carried out. This paper presents the investigation of various assemblies mainly with ROC4Sens readout chips. It demonstrates that multiple designs fulfill the requirements in terms of breakdown voltage, leakage current and efficiency. The single point resolution for 50 × 50 μm 2 pixels is measured as 4.0 μm for non-irradiated samples, and 6.3 μm after irradiation to $\Phi_{\text {eq}}$ = 7.2 × 10 15 cm –2 .

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
DOE OSTI2022

Long-term 3D MHD simulations of black hole accretion discs formed in neutron star mergers

ABSTRACT We examine the long-term evolution of accretion tori around black hole (BH) remnants of compact object mergers involving at least one neutron star, to better understand their contribution to kilonovae and the synthesis of r-process elements. To this end, we modify the unsplit magnetohydrodynamic (MHD) solver in flash 4.5 to work in non-uniform three-dimensional spherical coordinates, enabling more efficient coverage of a large dynamic range in length scales while exploiting symmetries in the system. This modified code is used to perform BH accretion disc simulations that vary the initial magnetic field geometry and disc compactness, utilizing a physical equation of state, a neutrino leakage scheme for emission and absorption, and modelling the BH’s gravity with a pseudo-Newtonian potential. Simulations run for long enough to achieve a radiatively inefficient state in the disc. We find robust mass ejection with both poloidal and toroidal initial field geometries, and suppressed outflow at high disc compactness. With the included physics, we obtain bimodal velocity distributions that trace back to mass ejection by magnetic stresses at early times, and to thermal processes in the radiatively inefficient state at late times. The electron fraction distribution of the disc outflow is broad in all models, and the ejecta geometry follows a characteristic hourglass shape. We test the effect of removing neutrino absorption or nuclear recombination with axisymmetric models, finding ${\sim} 50{{\ \rm per\ cent}}$ less mass ejection and more neutron-rich composition without neutrino absorption, and a subdominant contribution from nuclear recombination. Tests of the MHD and neutrino leakage implementations are included.

Fahlman, Steven (ORCID:0000000348759940)↗
NASA NTRS1992

Neutron, gamma ray, and temperature effects on the electrical characteristics of thyristors

Experimental data showing the effects of neutrons, gamma rays, and temperature on the electrical and switching characteristics of phase-control and inverter-type SCR's are presented. The special test fixture built for mounting, heating, and instrumenting the test devices is described. Four SCR's were neutron irradiated at 300 K and four at 365 K for fluences up to 3.2 x 10 exp 13 n/sq. cm, and eight were gamma irradiated at 300 K only for gamma doses up to 5.1 Mrads. The electrical measurements were made during irradiation and the switching measurements were made only before and after irradiation. Radiation induced crystal defects, resulting primarily from fast neutrons, caused the reduction of minority carrier lifetime through the generation of R-G centers. The reduction in lifetime caused increases in the on-state voltage drop and in the reverse and forward leakage currents, and decreases in the turn-off time.

Frasca, A. J.↗
NASA NTRS1992

Neutron, gamma ray, and temperature effects on the electrical characteristics of thyristors

Experimental data showing the effects of neutrons, gamma rays, and temperature on the electrical and switching characteristics of phase-control and inverter-type SCR's are presented. The special test fixture built for mounting, heating, and instrumenting the test devices is described. Four SCR's were neutron irradiated at 300 K and four at 365 K for fluences up to 3.2 x 10 exp 13 pn/sq. cm, and eight were gamma irradiated at 300 K only for gamma doses up to 5.1 Mrads. The electrical measurements were made during irradiation and the switching measurements were made only before and after irradiation. Radiation induced crystal defects, resulting primarily from fast neutrons, caused the reduction of minority carrier lifetime through the generation of R-G centers. The reduction in lifetime caused increases in the on-state voltage drop and in the reverse and forward leakage currents, and decreases in the turn-off time.

Frasca, A. J.↗
DOE OSTI2025

Magnetic structure determination of multiple phases in the multiferroic candidate GdCrO 3

Due to their potential applications in low-power consumption and/or multistate memory devices, multiferroic materials have attracted a lot of attention in the condensed matter community. As part of the effort to identify new multiferroic compounds, perovskite-based GdCrO 3 was studied in both bulk and thin film samples. A strong enhancement of the capacitance in a field suggested ferroelectric behaviour but significant leakage and no well developed P–E hysteresis loops were observed. Measurements clearly indicate the existence of a polar phase but only below 2 K (likely connected to Gd ordering). Here the determination of the magnetic structure through neutron diffraction collected on an isotopic 160 GdCrO 3 sample at the WISH diffractometer at ISIS is reported. The presence of three successive magnetic phases as a function of temperature (commensurate, spin re-orientation and incommensurate phases once the Gd order), previously only seen by magnetization, is confirmed. Using the most recent guidelines for reporting the determined structures, we highlight the benefits of using such nomenclature for discussing physical properties and consider possible mechanisms and couplings that led this seemingly rather isotropic system to display the complex structures observed.

incommensurate magnetic structure↗
DOE OSTI2022

Characterizing the Performance of Fission Chambers for Local Neutron Flux and Spectrum Measurement

Three fission chambers were tested at The Ohio State University Research Reactor (OSURR) to evaluate fission chambers for neutron flux and spectrum measurements. Two of the fission chambers are commercial Photonis CFUR43 fission chambers—one utilizing highly enriched uranium-235 fissile deposits for thermal neutron detection and the other with highly depleted uranium-238 for fast neutron detection. This experiment was also performed in collaboration with French Alternative Energies and Atomic Energy Commission (CEA) with CEA suppling a uranium-235 loaded fission chamber built from the Photonis CFPR CE8/9 kit. The fission chambers were irradiated in a movable 6.5 inch dry tube at reactor powers of 50 kW, 200 kW, and 450 kW at ambient temperature and at 350°C. While all sensors demonstrated good linear sensitivity to reactor power, a leakage current of 6 nA was measured for the CFUR43 detectors. Additionally, the measured signal ratios of the two CFUR43 detectors did not match the theoretical values and are subject to further investigation on individual signal contributors.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
DOE OSTI2023

Addition of tabulated equation of state and neutrino leakage support to illinoisgrmhd

Here we have added support for realistic, microphysical, finite-temperature equations of state (EOS) and neutrino physics via a leakage scheme to illinoisgrmhd, an open-source GRMHD code for dynamical spacetimes in the einstein toolkit. These new features are provided by two new, nrpy+-based codes: nrpyeos, which performs highly efficient EOS table lookups and interpolations, and nrpyleakage, which implements a new, adaptive mesh refinement (AMR)-capable neutrino leakage scheme in the einstein toolkit. We have performed a series of strenuous validation tests that demonstrate the robustness of these new codes, particularly on the Cartesian AMR grids provided by carpet. Furthermore, we show results from fully dynamical GRMHD simulations of single unmagnetized neutron stars, and magnetized binary neutron star mergers. This new version of illinoisgrmhd, as well as nrpyeos and nrpyleakage, is pedagogically documented in jupyter notebooks and fully open source. The codes will be proposed for inclusion in an upcoming version of the einstein toolkit.

79 ASTRONOMY AND ASTROPHYSICS↗
NASA NTRS1972

Calculation of the lunar photon albedo from galactic and solar proton bombardment.

The lunar photon albedo due to cosmogenic and primordial photon sources has been calculated. The individual photon leakage spectra from prompt photons produced by galactic cosmic ray (GCR) and solar cosmic ray (SCR) induced nuclear interactions, from the decay of GCR- and SCR-induced radionuclides, and from the decay of naturally occurring radionuclides are given. An approximate estimate of the leakage from the photon-electron cascade initiated by the decay of neutral pions is also given. Monte Carlo methods have been used to determine the nucleon-meson cascade, and discrete-ordinates methods were used for the photon and low-energy neutron transport.

Armstrong, T. W.↗
NASA NTRS1975

Cosmic ray intensity variations during 0200-0700 UT, August 5, 1972

The cosmic ray intensity variations over the energy range of about 0.5 MeV to 1 GeV during the early part of August 5 are discussed in relation to the intensity changes during the entire period of activity (August 2 to 11). Measurements of the interplanetary magnetic field and particle data from ground-based neutron monitors, lunar sensors, and detectors in board Explorers 41 and 43 are used in the investigation. Analysis is made of intensity changes during the period from 0200 to 0700 UT on August 5, the north-south asymmetry in neutron monitor intensities, changes in the alpha particle/proton flux ratios, the lag in onset times as recorded by the two Explorers, and observations of flux enhancement by the lunar detectors. The results indicate that the enhanced particle fluxes (about 1 GeV) were due to a leakage of galactic cosmic rays into a low-intensity region of the interplanetary magnetic field bounded by tangential discontinuities, which connected to different particle sources both near the sun and in the outer solar system.

Venkatesan, D.↗
DOE OSTI2023

Cadmium Magnesium Telluride for Next-Generation X-Ray Free Electron Laser, Synchrotron, and Many Other Applications

We developed a picosecond photodetector based on our Bridgman-grown and specially engineered cadmium magnesium telluride (Cd 1–x MgxTe) single crystal that is sensitive to both optical and X-ray pulses for coarse timing in free-electron laser applications. Cd 1–x MgxTe is a widebandgap semiconductor with potential applications, not only in optoelectronics, but also in particle physics as an intense pulse radiation detector for bremsstrahlung, X-ray/gamma-ray radiation, thermal neutrons, and medical imaging. For femtosecond optical and X-ray crosscorrelation, the material must have a very short lifetime, a condition that is opposite to that required for nuclear spectroscopy applications. At the same time, the material also needs to have a very low bulk leakage current, in the 10–90 nA range for voltages to even 1000 V. Hence, the ability to tailor or engineer the material is very crucial. Picosecond response and the crystal growth of this specially engineered Cd 1–x MgxTe material are presented. Furthermore, other characterization and transient measurements are discussed along with room-temperature semiconductor detector performance for other nuclear radiation detection applications.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Cadmium Magnesium Telluride for Next Generation X-Ray Free Electron Laser, Synchrotron and Many Other Applications

We developed a picosecond photodetector based on our Bridgman grown and specially engineered Cadmium Magnesium Telluride (Cd 1-x Mg x Te) single crystal that is sensitive to both optical and x-ray pulses for coarse timing in Free Electron Laser applications. Cd 1-x Mg x Te is a wide bandgap semiconductor material with potential applications, not only in optoelectronics, but also in particle physics as an intense pulse radiation detector for bremsstrahlung, X-ray/gamma ray radiation, thermal neutrons, and medical imaging. However, for femtosecond optical and x-ray cross correlation, the material has to have very short lifetime, a condition that is opposite to that required for nuclear spectroscopy applications. At the same time, the material also needs to have very low bulk leakage current, in the 0.10 pA range. Hence the ability to tailor or engineer the material is very crucial. In this paper, picosecond response and the crystal growth of this specially engineered cadmium magnesium telluride material will be presented. Other material characterization and transient measurements will also be discussed along with room temperature semiconductor detector performance for other nuclear radiation detection applications.

36 MATERIALS SCIENCE↗
DOE OSTI2024

HYDRODYNAMIC TESTING OF ZIRCALOY TO STEEL HUB COUPLINGS FOR USE IN ADVANCED TEST REACTOR I-LOOP TUBE

The ATR I-positions' isolation from the flux trap region provides an opportunity for a test facility that could create conditions representative of commercial light water reactors. Such a facility requires piping couplings and joints that withstand extreme thermal and pressure cycling. Also, transitioning from steel to zircaloy piping inside the reactor vessel allows the neutronic properties of zircaloy to be leveraged while using cost-effective stainless steel outside of the core. Grayloc-style hub couplings will act as transition points between stainless steel piping and zircaloy piping inside the reactor vessel. These couplings have not been sufficiently tested for leakage where there is a transition between materials. This transition is a concern because the thermal expansion coefficients of the materials differ. Seal integrity between the two components may be greatly affected by thermal expansion at the connection. Thus, the effect of thermal cycling must be assessed. Thermal and pressure cycling and hydrodynamic testing will be conducted to verify seal integrity of the steel to zircaloy hub coupling when subjected to ATR conditions.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗
DOE OSTI2022

A preconceptual design of an inverted Stable-Salt Reactor

This paper presents a preconceptual design of an inverted stable-salt reactor (SSR), with the unique feature that the static fuel salt is accommodated in one single bulk fuel container, while the coolant salt is circulating through the core via flow tubes penetrating the fuel container.The inverted SSR is expected to substantially decrease the capital cost compared to the state-of-the-art SSR such as the SSR-W designed by Moltex Energy, because one single gas vent at the top of the fuel container is required in the inverted SSR to prevent the leakage of the radioactive fission product gases instead of one gas vent in each of the hundreds of thousands of fuel tubes in SSR-W. In addition, the operation of the inverted SSR is largely simplified. However, numerous challenges associated with the design of the inverted SSR still remain to be overcome. Preliminary neutronics and thermal-hydraulics performance characteristics of the inverted SSR are assessed in this study. A viable core configuration of the inverted SSR is identified, and the superior characteristics of the inverted SSR, including a better neutron economy and a lower maximum fuel temperature, are demonstrated in this paper. (authors)

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗