Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Nb”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8
All sourcesNASA NTRSDOE OSTI
NASA NTRS1987

Material tradeoffs to minimize flooding reactivity

In the GE 100 KWe SP-100 design, the array of fuel pins in the core was surrounded by a thin neutron barrier made of a mixture of Nb-1 percent Zr and 20 percent B4C. The purpose of this barrier was to prevent the return to the reactor of thermalized neutrons in the event of a reactor flooding accident. Neutronically, the barrier produced a reduction in k sub eff of 15 percent. However, a mixture of Nb-1 percent Zr and B4C is a development item and may not be possible to produce. Several alternatives to this design were investigated. These include the use of W-26 percent Re for the fuel barrier and the introduction of fuel pin ducts made of Ta-8 percent W-2 percent Hf, Hf-10 percent Nb or pure Re. The use of W-26 percent Re for the fuel barrier material in place of W, and the use of T111, Hf-10 percent Nb, or Re duct material in place of Nb-1 percent Zr or Nb-1 percent Zr-20 percent B4C were found to substantially decrease k sub eff in the flooding situation. The best choice neutronically for duct material is Hf-10 percent Nb, because of its small impact on the k sub eff of the normal core.

Protsik, R.↗
NASA NTRS2006

Derivation of Improved Surface and TOA Broadband Fluxes Using CERES-derived Narrowband-to-Broadband Coefficients

Satellites can provide global coverage of a number of climatically important radiative parameters, including broadband (BB) shortwave (SW) and longwave (LW) fluxes at the top of the atmosphere (TOA) and surface. These parameters can be estimated from narrowband (NB) Geostationary Operational Environmental Satellite (GOES) data, but their accuracy is highly dependent on the validity of the narrowband-to-broadband (NB-BB) conversion formulas that are used to convert the NB fluxes to broadband values. The formula coefficients have historically been derived by regressing matched polarorbiting satellite BB fluxes or radiances with their NB counterparts from GOES (e.g., Minnis et al., 1984). More recently, the coefficients have been based on matched Earth Radiation Budget Experiment (ERBE) and GOES-6 data (Minnis and Smith, 1998). The Clouds and the Earth's Radiant Energy Budget (CERES see Wielicki et al. 1998)) project has recently developed much improved Angular Distribution Models (ADM; Loeb et al., 2003) and has higher resolution data compared to ERBE. A limited set of coefficients was also derived from matched GOES-8 and CERES data taken on Topical Rainfall Measuring Mission (TRMM) satellite (Chakrapani et al., 2003; Doelling et al., 2003). The NB-BB coefficients derived from CERES and the GOES suite should yield more accurate BB fluxes than from ERBE, but are limited spatially and seasonally. With CERES data taken from Terra and Aqua, it is now possible to derive more reliable NB-BB coefficients for any given area. Better TOA fluxes should translate to improved surface radiation fluxes derived using various algorithms. As part of an ongoing effort to provide accurate BB flux estimates for the Atmospheric Radiation Measurement (ARM) Program, this paper documents the derivation of new NB-BB coefficients for the ARM Southern Great Plains (SGP) domain and for the Darwin region of the Tropical Western Pacific (DTWP) domain.

Khaiyer, Mandana M.↗
NASA NTRS2006

A Preliminary Analysis of Calcifying Particles in the Serum and Prostates of Patients with Prostatic Inflammation

Chronic diseases of the prostate such as benign prostatic hyperplasia (BPH) & chronic pelvic pain syndrome (CPPS) have associated findings of chronic inflammation, despite a lack of causal relationship. Numerous attempts to define an infectious agent responsible for the clinical findings have been inconsistent. The possibility of an infectious agent, that has not been uncovered with routine culturing methods, forms the basis for this study. Serum from 940 healthy Finnish men were compared with serum from 40 Crohn's, 40 path dx prostatitis, & 40 with path dx carcinoma, using an enzyme-linked immunosorbant assay (ELISA), to detect antigens specific to Nanobacteria(NB) utilizing monoclonal antibodies (Ab) 5/3 and 8D10. This ELISA has not been validated for detecting NB-associated with clinical prostatic disease, yet cross-reactivity with other bacterial species is low. Immunohistochemistry was performed on de-paraffinized prostatic tissue slides, de-calcified with EDTA and stained with the DAKO Catalyzed Signal Amplification kit, employing 8D10 as the primary (target/antigen-detecting) Ab. The mean (plus or minus SD) & median concentrations of NB antigen (U/50 L) were 379.59 (plus or minus 219.28) & 640.00 for patients with prostatitis (BPH) vs 3.31 (plus or minus 3.55) & 2.94 for prostate adenocarcinoma, 1.88 (plus or minus 2.94) & 0.80 for Crohn's disease, & 7.43 (plus or minus 25.57) & 0.00 for patients with no clinical prostatic disease. Unpaired t-tests revealed statistically significant differences between the prostatitis (BPH) sera & each of the other groups with p less than 0.005, but no differences between the other groups themselves. Preliminary studies with immunohistochemistry & 3-D confocal microscopy reveal 16/24 tissue sections + for NB Ag in BPH vs. only 2/22 tissue sections with prostate cancer. The preliminary findings of this serum screening study suggest that NB antigen may be commonly found in the serum of patients with the pathological diagnosis of prostatitis. Preliminary immunohistologic studies, suggest that NB may be found within the gland itself at a higher rate in patients with BPH relative to patients with adenocarcinoma, however confirmatory studies with a more specific ELISA technique, primary cultures, & with larger numbers of patients in a prospective design are required to determine if 1) NB are a causative organism for clinical hyperplastic and inflammatory disease, & if 2) serological testing can be used to discriminate patients with nanobacterial-associated prostatic disease.

Jones, Jeffrey A.↗
NASA NTRS2009

Validation of Improved Broadband Shortwave and Longwave Fluxes Derived From GOES

Broadband (BB) shortwave (SW) and longwave (LW) fluxes at TOA (Top of Atmosphere) are crucial parameters in the study of climate and can be monitored over large portions of the Earth's surface using satellites. The VISST (Visible Infrared Solar Split-Window Technique) satellite retrieval algorithm facilitates derivation of these parameters from the Geostationery Operational Environmental Satellites (GOES). However, only narrowband (NB) fluxes are available from GOES, so this derivation requires use of narrowband-to-broadband (NB-BB) conversion coefficients. The accuracy of these coefficients affects the validity of the derived broadband (BB) fluxes. Most recently, NB-BB fits were re-derived using the NB fluxes from VISST/GOES data with BB fluxes observed by the CERES (Clouds and the Earth's Radiant Energy Budget) instrument aboard Terra, a sun-synchronous polar-orbiting satellite that crosses the equator at 10:30 LT. Subsequent comparison with ARM's (Atmospheric Radiation Measurement) BBHRP (Broadband Heating Rate Profile) BB fluxes revealed that while the derived broadband fluxes agreed well with CERES near the Terra overpass times, the accuracy of both LW and SW fluxes decreased farther away from the overpass times. Terra's orbit hampers the ability of the NB-BB fits to capture diurnal variability. To account for this in the LW, seasonal NB-BB fits are derived separately for day and night. Information from hourly SW BB fluxes from the Meteosat-8 Geostationary Earth Radiation Budget (GERB) is employed to include samples over the complete solar zenith angle (SZA) range sampled by Terra. The BB fluxes derived from these improved NB-BB fits are compared to BB fluxes computed with a radiative transfer model.

Khaiyer, Mandana M.↗
NASA NTRSDate not supplied

Open-source Numerical Modeling of Solidification Cracking Susceptibility: Application to Refractory Alloy Systems

Introduction. Alloys such as aluminum, nickel-base, and austenitic stainless steels are susceptible to solidification cracking during welding and 3D printing. Compositional optimization is one method used to effectively mitigate solidification cracking of those alloy systems. With the surge in hypersonic and in-space propulsion activities, refractory metals (Nb, Mo, Ta, W, and Re) and their alloy derivatives are increasing in importance due to their extreme high melting point and retention of high-temperature strength; however, their chemistry was most typically optimized to promote ductility during mechanical operations such as drawing and forming. Welding of such alloys has been a challenge due to a number of issues including solidification cracking, atmospheric contamination (O, C, and N), as well as a shift in ductile-to-brittle transition to higher temperature following grain growth induced by welding. Compositional optimization of refractory alloys for solidification cracking resistance in particular is desirable as their usage increases with the advent of advanced manufacturing methods such as 3D printing. This work evaluates the effect of compositional variation in refractory metal systems on the solidification cracking susceptibility with the goals of optimizing existing alloys and joining process techniques, and formulating new alloys with increased solidification cracking resistance. Experimental Procedures. A python code was developed in a Jupyter notebook environment (Michael and Sowards, 2023) to facilitate the calculation of crack susceptibility index proposed by Kou (2015). Composition is entered as a single point, or as a 1-D or 2-D array. The notebook calls pycalphad (Otis and Liu, 2017 and Bocklund et al, 2020) to calculate the evolution of fraction solid as a function of temperature (under either Scheil or equilibrium assumptions) and then evaluates steepness of the fraction solid curve near the terminal stage of solidification to predict solidification cracking resistance. Open source thermodynamic databases available at online repositories are used (van de Walle). The process is setup in an automated fashion to generate plots that show variation in solidification cracking susceptibility according to composition on 1-D line plots or 2-D contour plots. The Jupyter notebook and crack susceptibility algorithm was also integrated with a widely used commercial CALPHAD code for validation and alloy exploration. Results and Discussion. The crack susceptibility model was first validated against a series of refractory alloy compositions evaluated in past work which utilized a specialized Varestraint test built inside a vacuum chamber environment (Lessman and Gold, 1971). The alloys tested in the Varestraint apparatus included T-111 (Ta-8W-2Hf), ASTAR-811C (Ta-8W-1Re-0.7Hf-0.025C), FS-85 (Nb-27Ta-10W-1Zr), T-222 (Ta-9.6W-2.4Hf-0.01C), Ta-10W, B-66 (Nb-5Mo-5V-1Zr), and SCb-291 (Nb-10W-10Ta). The initial test of the model showed a strong correlation with empirical Varestraint data, i.e., a Spearman rank correlation between model predictions and hot cracking measurements was observed to be greater than 0.8. Following the validation, a set of refractory metal binary mixtures was investigated to evaluate sensitivity of Nb, Mo, W, and Ta to C, N, and O content. A series of plots were produced that suggest ppmw ranges of C, N, and O where solidification cracking increases significantly and reaches a maximum. Also comparative ranking of each primary refractory metal to each interstitial was produced. For example C produces greater cracking response in Mo whereas O produces greater cracking response in Ta and Nb. Such compositional values have utility in setting limits on pickup of these interstitial elements during welding and printing rather than using a one-size-fits-all approach. Furthermore, the results have use in determining additive powder recycling requirements, which is especially pertinent for refractory metal powders due to their high cost compared to conventional alloys. Another application created thousands of hypothetical alloys within the nominal specified composition range of two widely used refractory alloys C103 (Nb-10Hf-1Ti) and TZM (Mo-0.5Ti-0.1Zr). The cracking index was calculated for the alloys and results were fed into machine learning regression techniques including Multiple Linear Regression, Ridge Regression, and Lasso Regression to determine relative potency each alloying element had on computed solidification cracking index. A series of linear equations were produced that relate composition of C103 and TZM to solidification cracking index. The crack susceptibility of C103 for example is described by an equation of the form: cracking index ~ O + 0.667*C + 0.635*N + 0.00037*Ta – 0.0008*Hf (in wt.%) From that equation, it is clear that O has strong propensity to induce solidification cracking. Interestingly, Hf is shown to reduce calculated cracking response. Finally, realizing the potential of this method to discover new refractory alloy formulations across the period table that have low solidification cracking sensitivity, the code was applied to new untested alloy systems including W-Zr-C, W-Ta-C, and others. Conclusions. In summary, an open source numerical method has been developed using Python code to calculate Kou’s crack susceptibility index. The method was applied to refractory metals which are inherently difficult to study from a weldability testing standpoint since inert shielding gas is not sufficient and welding is typically done in vacuum, especially in light of findings presented here where oxygen has profound influence on solidification cracking. This work revealed the effect of compositional variations on a series of refractory metals and showed the framework defined here will be useful in 1) the development of new alloys that have improved weldability and 3D printability, 2) placing compositional limits on existing alloys, and 3) ensuring adequate controls of manufacturing processes such as 3D printing where powder reuse is critical. Keywords. pycalphad; Python; refractory metals; solidification cracking. References. B. Bocklund et. al. (2020) http://doi.org/10.5281/zenodo.3630657. S. Kou. (2015) https://doi.org/10.1016/j.actamat.2015.01.034. G.G. Lessmann and R.E. Gold. Welding Journal, issue 1, pp. 1-s – 8-s (1971). F.N. Michael and J.W. Sowards. NASA/TM-20230002218 (2023). R. Otis and Z.-K. Liu. (2017) http://doi.org/10.5334/jors.140. A. Van de Wallle et. al. (2018) https://doi.org/10.1016/j.calphad.2018.04.003.

pycalphad↗
NASA NTRS1976

Quaternary and quinary modifications of the eutectic superalloy gamma/gamma prime-delta

Quaternary modifications and quinary additions from the elements Co, Ti, Mo, W, Re, B, Si, and Ta to the baseline quaternary alloy gamma/gamma prime-delta Ni-19.7 at.% Nb-6.0 at.% Cr-2.5 at.% Al are examined for various concentrations. From modification studies five alloys were chosen for detailed mechanical property characterization: Ni-19.7 Nb-6.0 Cr-2.5 Al-1.0 W; Ni-19.7 Nb-6.0 Cr-2.5 Al-1.0 Mo; Ni-18.6 Nb-6.0 Cr-2.5 Al-0.87 Ti; Ni-20.2 Nb-6.0 Cr-2.5 Al-2.0 Co; and Ni-17.9 Nb-6.0 Cr-2.5 Al-3.0 Ta. It is shown that extensive alloying of the baseline quaternary alloy is possible for elements exhibiting a wide solubility range in both phases, and that limited substitution of W, Mo, Re, Si, and B is possible for elements with restricted solid solubility especially in the delta phase. Improvement of creep rupture strength and cyclic oxidation resistance at 1100 C is discussed.

Lemkey, F. D.↗
NASA NTRS1978

Some properties of low-vapor-pressure braze alloys for thermionic converters

Density, dc electrical resistivity, thermal conductivity, and linear thermal expansion are measured for arc-melted rod-shaped samples of binary eutectics of Zr, Hf, Ru, Nb, Ir, Mo, Ta, Os, Re, and W selected as very-low-pressure braze fillers for thermionic converters. The first two properties are measured at 296 K for Zr-21.7 at% Ru, Zr-13 wt% W, Zr-19 wt% W, Zr-22.3 at% Nb, Nb-66.9 at% Ru, Hf-25.3 wt% Re, Zr-25.7 at% Ta, Hf-22.5 at% W, and Nb-35 wt% Mo. The last property is measured from 293 K to 2/3 melting point for specified alloys of different compositions. Resistivities of 0.000055 to 0.000181 ohm-cm are observed with the alloys having resistivities about ten times that of the less resistive constituent metal and about three times that of the more resistive constituent metal, except for Zr-19 wt% W and Nb-35 wt% Mo (greater resistivities). Thermal expansion coefficients vary from 0.000006 to 0.0000105/K. All brazes exhibit linear thermal expansion near that of their constituent metals.

Bair, V. L.↗
NASA NTRS1988

Influence of alloying elements on the oxidation behavior of NbAl3

NbAL3 is one candidate material for advanced aeropropulsion systems because of its high melting point, low density, and good oxidation resistance. Although NbAl3 has the lowest oxidation rate among the binary Nb-Al alloys, it does not form exclusive layers of protective Al2O3 scales. Recently Perkin et al., have shown the feasibility of forming alumina scales on Nb-Al alloys at greatly reduced Al contents. However, the objective was to maintain the high Al content, and hence low density, while achieving the capability of growing protective alumina scales. Alloy development followed approaches similar to those used successfully for superalloys and oxidation resistant MCrAlY coatings. Among the three elements examined (Ti, Si, and Cr) as ternary additions to Nb-Al3, Cr was the most effective in favoring the selective oxidation of Al. Nb-41Al-8Cr formed exclusive layers of alumina and had a k sub p value of 0.22 mg squared/cm (sup 4)/hr at 1200 C. The addition of 1 wt percent Y to this alloy was also beneficial, resulting in nearly an order of magnitude decrease in K sub p at 1200 C. Further improvements were achieved by adding about 1 wt percent Si to the quaternary alloy. The k sub p value of 0.012 mg squared/cm (sup 4)/hr for Nb-40Al-8Cr-1Y-1Si at 1200 C was identical to the best NiAl + Zr alloys. These NbAl3 alloys also exhibited excellent cyclic oxidation resistance for 100 hr at 1200 C, being nearly equivalent to NiAl + Zr.

Hebsur, M. G.↗
NASA NTRS1989

Influence of alloying elements on the oxidation behavior of NbAl3

NbAl3 is one candidate material for advanced aeropropulsion systems because of its high melting point, low density, and good oxidation resistance. Although NbAl3 has the lowest oxidation rate among the binary Nb-Al alloys, it does not form exclusive layers of protective Al203 scales. Recently Perkin et al., have shown the feasibility of forming alumina scales on Nb-Al alloys at greatly reduced Al contents. However, the objective was to maintain the high Al content, and hence low density, while achieving the capability of growing protective alumina scales. Alloy development followed approaches similar to those used successfully for superalloys and oxidation resistant MCrAly coatings. Among the three elements examined (Ti, Si, and Cr) as ternary additions to Nb-Al3, Cr was the most effective in favoring the selective oxidation of Al. Nb-41Al-8Cr formed exclusive layers of alumina and had a k sub p value of 0.22 mg squared/cm (sup 4)/hr at 1200 C. The addition of 1 wt percent Y to this alloy was also beneficial, resulting in nearly an order of magnitude decrease in K sub p at 1200 C. Further improvements were achieved by adding about 1 wt percent Si to the quaternary alloy. The k sub p value of 0.012 mg squared/cm (sup 4)/hr for Nb-40Al-8Cr-1Y-1Si at 1200 C was identical to the best NiAl + Zr alloys. These NbAl3 alloys also exhibited excellent cyclic oxidation resistance for 100 hr at 1200 C, being nearly equivalent to NiAl + Zr.

Hebsur, M. G.↗
NASA NTRS1990

Refractory metal alloys and composites for space power systems

Results are presented on recent studies of refractory-metal-alloy and refractory-metal-composite technologies for space power systems, with emphasis on work performed at the Lewis Research Center in support of the Ground Engineering System (GES) for the SP-100 reactor. Special attention is given to the mechanical properties of alloys with compositions Nb-1Zr and Nb-0.1Zr-0.1C (the PWC-11 alloy) and to advanced fiber-reinforced composites. The results to date indicate that, for the GES at a power level of about 100 kWe, the PWC-11 has attractive creep properties that will extend the capabilities of the SP-100 reactor compared to a similar system fabricated from Nb-1Zr. On the other hand, tungsten-reinforced Nb-1Zr composites were found to provide a ten-fold and four-fold creep strength over Nb-1Zr and PWC-11, respectively, at 1400 to 1500 K.

Stephens, R.↗
NASA NTRS2011

Comment on "'Elevated Heat Pump' Hypothesis for the Aerosol-Monsoon Hydroclimate Link: 'Grounded' in Observations?" by S. Nigam and M. Bollasina

In their recent paper, Nigam and Bollasina [2010] (hereinafter NB) claimed to have found observational evidences that are at variance with the elevated heat pump (EHP) hypothesis regarding the possible impacts of absorbing aerosols on the South Asian summer monsoon [Lau et al., 2006; Lau and Kim, 2006]. We found NB's arguments and inferences against the EHP hypothesis flawed, stemming from their own out of context interpretation of the hypothesis. NB argued that the simultaneous negative correlation of aerosol with rainfall, and correlations with other quantities in May, are evidence against the EHP hypothesis. Their argument cannot be justified. First, Lau and Kim [2006] (hereinafter LK06) never stated that the main rainfall response to EHP is in May. Second, the EHP is about responses of the entire Indian monsoon system that are nonlocal in space and time with respect to the aerosol forcing. As shown in Figure 4 of LK06, while the aerosol anomalies are strongest in April-May, the strongest rainfall response is in June-July, with the enhanced rainfall fed by an induced thermally driven circulation which brings additional moisture from the ocean to the Indian subcontinent. Third, the increased rainfall over the Bay of Bengal as shown in Figure 1a of NB and the increased low-level convergence in Figure 1f of NB do not necessarily reflect responses associated with EHP but rather the large ]scale circulation that provides the buildup of the aerosols before the onset of the monsoon rainfall over India. Because aerosol can only accumulate where there is little or no washout by rain, the negative correlation is a necessary condition for increased atmospheric loading of aerosols. For the same reason, the spatial distributions of rainfall and aerosol generally are offset with each other, i.e., high aerosol in regions of low rainfall. This is evident in Figure 1, which shows the climatological mean of the MODIS aerosol optical depth (AOD), and TRMM rainfall over India in May. The maximum AOD is found over the Indo-Gangetic Plain and the desert regions of northwest India and Pakistan

Lau, K. M.↗
NASA NTRS1985

Undercooling of niobium-germanium alloys in a 100 meter drop tube

The undercoolings of pure Nb and Nb-Ge alloys are examined using the 100-m drop tube of the Marshall Space Flight Center. The temperatures of the samples prior to release were measured, and IR detectors were utilized to monitor recalescence from solidification. It is observed that the Nb and Nb-Ge samples undercooled to the homogeneous nucleation limit. The data reveal that all the samples displayed a dendritic primary phase, except for alloys nucleating in the beta-phase field, which had a cellular phase. The composition of these phases are studied using EDXA; it is detected that the composition of the phases corresponds to the Jorda (1978) phase diagram.

Hofmeister, W. H.↗
NASA NTRS2001

Reduced T(sub c) Niobium Superconducting HEB Mixers

A reduction in the mixer noise is expected when using superconductors with a lower transition temperature (T(sub c)) since the thermal noise components of the mixer noise should scale with T(sub c). Also, the local oscillator (LO) power required for a diffusion-cooled device should decrease as T(sub c) when T(sub bath) << T(sub c). We previously studied mixing in aluminum based hot-electron bolometers (HEBs) at microwave frequencies (approximately 30 GHz), and observed a significant improvement in noise performance, and a reduction in LO power as predicted. However, the bias voltage range over which good mixer performance was observed was approximately 5 - 10 microV. These devices are thus susceptible to saturation effects, in particular output saturation. In the present work, we have investigated Nb HEBs whose T(sub c) is lowered by applying a magnetic field. The goal is to study a case intermediate between Nb and Al, and hopefully to find properties that will allow use in practical receivers. A 15 kOe perpendicular magnetic field was applied to a Nb HEB (L = 0.16 micrometers, W = 0.08 micrometers, R(sub N) = 90 ohms) to reduce T(sub c) from 5.2 K to 2.4 K. The mixer noise, as inferred from the output noise and the conversion efficiency, decreased from 390 K, DSB to 171 K, DSB. The LO power required for near optimum mixer conversion efficiency (eta(sub mixer) = -9 dB in this device) was 8 nW in zero field, and approximately 2 nW when T(sub c) was reduced to 2.4 K. T(sub bath) = 0.22 K. The conversion bandwidth was previously measured to be 2.4 GHz and the same bandwidth was observed in the presence of a magnetic field. By lowering T(sub c), the voltage range over which good mixing was observed also decreased. However, even with T(sub c) reduced to 2.4 K, the conversion efficiency dropped by 3 dB from its maximum value only when the bias voltage was changed by approximately 90 microV. Saturation effects should thus be much less of a concern in these devices than in Al HEBS. In situations where the application of a large magnetic field is not feasible, we suggest using Ta based HEBS. Ta HEBs should have T(sub c) = 3 - 3.5 K and material properties very similar to Nb.

Siddiqi, I.↗
NASA NTRS2008

Making Superconducting Welds between Superconducting Wires

A technique for making superconducting joints between wires made of dissimilar superconducting metals has been devised. The technique is especially suitable for fabrication of superconducting circuits needed to support persistent electric currents in electromagnets in diverse cryogenic applications. Examples of such electromagnets include those in nuclear magnetic resonance (NMR) and magnetic resonance imaging (MRI) systems and in superconducting quantum interference devices (SQUIDs). Sometimes, it is desirable to fabricate different parts of a persistent-current-supporting superconducting loop from different metals. For example, a sensory coil in a SQUID might be made of Pb, a Pb/Sn alloy, or a Cu wire plated with Pb/Sn, while the connections to the sensory coil might be made via Nb or Nb/Ti wires. Conventional wire-bonding techniques, including resistance spot welding and pressed contact, are not workable because of large differences between the hardnesses and melting temperatures of the different metals. The present technique is not subject to this limitation. The present technique involves the use (1) of a cheap, miniature, easy-to-operate, capacitor-discharging welding apparatus that has an Nb or Nb/Ti tip and operates with a continuous local flow of gaseous helium and (2) preparation of a joint in a special spark-discharge welding geometry. In a typical application, a piece of Nb foil about 25 m thick is rolled to form a tube, into which is inserted a wire that one seeks to weld to the tube (see figure). The tube can be slightly crimped for mechanical stability. Then a spark weld is made by use of the aforementioned apparatus with energy and time settings chosen to melt a small section of the niobium foil. The energy setting corresponds to the setting of a voltage to which the capacitor is charged. In an experiment, the technique was used to weld an Nb foil to a copper wire coated with a Pb/Sn soft solder, which is superconducting. The joint was evaluated as part of a persistent-current circuit having an inductance of 1 mH. A current was induced in a loop, and no attenuation of the current after a time interval 1,000 s was discernible in a measurement having a fractional accuracy of 10(exp -4): This observation supports the conclusion that the weld had an electrical resistance <10(exp -10) omega.

Penanen, Konstantin I.↗
NASA NTRS2008

Fast Electromechanical Switches Based on Carbon Nanotubes

Electrostatically actuated nanoelectromechanical switches based on carbon nanotubes have been fabricated and tested in a continuing effort to develop high-speed switches for a variety of stationary and portable electronic equipment. As explained below, these devices offer advantages over electrostatically actuated microelectromechanical switches, which, heretofore, have represented the state of the art of rapid, highly miniaturized electromechanical switches. Potential applications for these devices include computer memories, cellular telephones, communication networks, scientific instrumentation, and general radiation-hard electronic equipment. A representative device of the present type includes a single-wall carbon nanotube suspended over a trench about 130 nm wide and 20 nm deep in an electrically insulating material. The ends of the carbon nanotube are connected to metal electrodes, denoted the source and drain electrodes. At bottom of the trench is another metal electrode, denoted the pull electrode (see figure). In the off or open switch state, no voltage is applied, and the nanotube remains out of contact with the pull electrode. When a sufficiently large electric potential (switching potential) is applied between the pull electrode and either or both of the source and drain electrodes, the resulting electrostatic attraction bends and stretches the nanotube into contact with the pull electrode, thereby putting the switch into the "on" or "closed" state, in which substantial current (typically as much as hundreds of nanoamperes) is conducted. Devices of this type for use in initial experiments were fabricated on a thermally oxidized Si wafer, onto which Nb was sputter-deposited for use as the pull-electrode layer. Nb was chosen because its refractory nature would enable it to withstand the chemical and thermal conditions to be subsequently imposed for growing carbon nanotubes. A 200- nm-thick layer of SiO2 was formed on top of the Nb layer by plasma-enhanced chemical vapor deposition. In the device regions, the SiO2 layer was patterned to thin it to the 20-nm trench depth. The trenches were then patterned by electron- beam lithography and formed by reactive- ion etching of the pattern through the 20-nm-thick SiO2 to the Nb layer.

Kaul, Anupama↗
NASA NTRS2004

Nuclear Microprobe using Elastic Recoil Detection (ERD) for Hydrogen Profiling in High Temperature Protonic Conductors

The interaction between hydrogen and various high temperature protonic conductors (HTPC) has not been clearly understood due to poor densification and unreacted secondary phases. the melt-processing technique is used in producing fully dense simple SrCe(0.9)Y (0.10) O(3-delta) and complex Sr3Ca(1+x)Nb(2+x)O(9-delta) perovskites that can not be achieved by solid-state sintering. the possibilities of ion beam analysis have been investigated to quantify hydrogen distribution in HTPC perovskites subjected to water heat treatment. Nuclear microprobe technique is based on the interactions of a focused ion beam of MeV light ions (H-1, H-2, He-3, He-4,.) with the sample to be analyzed to determine local elemental concentrations at the cubic micrometer scale, the elastic recoil detection analysis technique (ERDA) has been carried out using He-4(+) microbeams and detecting the resulting recoil protons. Mappings of longitudinal sections of water treated SrCeO3 and Sr(Ca(1/3)Nb(2/3))O3 perovskites have been achieved, the water treatment strongly alters the surface of simple SrCe(0.9)Y(0.10)O(3-delta) perovskite. From Rutherford Back Scattering measurements (RBS), both Ce depletion and surface re-deposition is evidenced. the ERDA investigations on water treated Sr3Ca(1+x)Nb(2+x)O(9-delta) perovskite did not exhibit any spatial difference for the hydrogen incorporation from the surface to the centre. the amount of hydrogen incorporation for Sr3Ca(1+x)Nb(2+x)O(9-delta) was low and required further development of two less conventional techniques, ERDA in forward geometry and forward elastic diffusion H-1(p,p) H-1 with coincidence detection.

Berger, Pascal↗
NASA NTRS2016

Fabricating with Crystalline Si to Improve Superconducting Detector Performance

We built and measured radio-frequency (RF) loss tangent, tan δ, evaluation structures using float-zone quality silicon-on-insulator (SOI) wafers with 5 μm thick device layers. Superconducting Nb components were fabricated on both sides of the SOI Si device layer. Our main goals were to develop a robust fabrication for using crystalline Si (c-Si) dielectric layers with superconducting Nb components in a wafer bonding process and to confirm that tan δ with c-Si dielectric layers was reduced at RF frequencies compared to devices fabricated with amorphous dielectrics, such as SiO2 and SixNy, where tan δ ~ 10(exp -3). Our primary test structure used a Nb coplanar waveguide (CPW) readout structure capacitively coupled to LC resonators, where the capacitors were defined as parallel-plate capacitors on both sides of a c-Si device layer using a wafer bonding process with benzocyclobutene (BCB) wafer bonding adhesive. Our control experiment, to determine the intrinsic tan δ in the SOI device layer without wafer bonding, also used Nb CPW readout coupled to LC resonators; however, the parallel-plate capacitors were fabricated on both sides of the Si device layer using a deep reactive ion etch (DRIE) to access the c-Si underside through the buried oxide and handle Si layers in the SOI wafers. We found that our wafer bonded devices demonstrated F· δ = (8 +/- 2) × 10(exp -5), where F is the filling fraction of two-level states (TLS). For the control experiment, F· δ = (2.0 +/- 0.6) × 10(exp -5), and we discuss what may be degrading the performance in the wafer bonded devices as compared to the control devices.

Beyer, A. D↗