Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Microstructural evolution”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Microstructure evolution of gadolinium doped cerium oxide under large thermal gradients

In this report the effects of large thermal gradient annealing on the microstructure of 10 mol% gadolinium doped ceria (GDC) were investigated. GDC powder was prepared by solvent deficient method and sintered at 1650 °C for 10 h to achieve dense ceramics with ~8 μm grain size. The densified GDC samples were subsequently annealed using a 60 W infrared laser at over 2100 °C for 1 h under a thermal gradient equivalent to ~0.3–0.5 °C/μm. The post-annealed samples at 2150 °C for 1 h exhibit grains with average length and width of 37 and 28 μm, respectively. Electron backscattered diffraction (EBSD) analysis revealed that the post-annealed sample at 2150 °C consists of grains oriented close to five principal directions (<4 3 10>, <0 0 1> and <13 1 14> on [0 0 1], and <7 6 20> and <7 2 7> on [0 1 0]) within a tolerance angle of ±10°, whereas the grains of the pre-annealed sample are randomly oriented. Gadolinium diffuses 20–30 μm away from the irradiated surface, with the measured composition of regions deeper than 30 μm, Ce 0.86 Gd 0.14 O 1.93 , is close to that of the pre-annealed sample, Ce 0.87 Gd 0.13 O 1.94 . Enhancement of total conductivity of the post-annealed GDC (1.1 × 10 -3 S cm -1 at 500 °C, and 2.1 × 10 -2 S cm -1 at 700 °C) is observed when compared to the pre-annealed GDC (3.1 × 10 -5 S cm -1 at 500 °C, and 1.7 × 10 -3 S cm -1 at 700 °C), and points to the decrease in the grain boundary (GB) resistivity. This could be attributed to both the change in GB area and grain alignment.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Crystallization Mechanisms of Poly(vinylidene Fluoride- co -chlorotrifluoroethylene): Nucleation Transitions, Growth Kinetics, and Microstructure Evolution

The crystallization kinetics of FK-800, a commercial semicrystalline copolymer of chlorotrifluoroethylene and vinylidene fluoride (poly(CTFE-co-VDF)), dictate its microstructure and functional performance. Crystallization occurs between the glass transition (T g ≈ 31 °C) and melting point (T m ≈ 110 °C), with grain boundaries playing a key role in applications such as memristors, where they regulate filament growth. This study integrates in situ atomic force microscopy (AFM), grazing-incidence wide-angle X-ray scattering (GIWAXS), and differential scanning calorimetry (DSC) to characterize nucleation, growth, and morphology across the full crystallization window. Hot-stage AFM reveals a transition from homogeneous to heterogeneous nucleation near 45 °C and a shift from reaction-limited to diffusion-limited growth above 60 °C. Kinetics are analyzed using Lauritzen–Hoffman, Turnbull–Fisher, and Avrami models to extract surface free energies and activation barriers. A multiscale modeling framework is developed in which nucleation densities and growth rates measured by AFM are used to reconstruct Avrami kinetics, which are then validated against coverage data, and extrapolated to predict bulk crystallization behavior observed by DSC. GIWAXS confirms a primarily flat-on chain orientation at all temperatures, linking orientation to domain morphology. This integrative approach quantitatively connects nanoscale crystallization dynamics with macroscopic phase evolution, establishing a quantitative framework for modeling crystallization across time, temperature, and length scales.

Crystallization↗
DOE OSTI2019

Microstructural Evolution and Toughness of the Various HAZs in 1300-MPa-Grade Ultrahigh-Strength Structural Steel

The effect of heat input on the microstructure and toughness of simulated subregions was investigated by welding thermal simulations and Charpy impact tests. The results indicate that the microstructures of the simulated coarse and fine grain heat affected zone (CGHAZ and FGHAZ) gradually changed from lath martensite to a mixture of lath martensite/lath bainite and finally to granular bainite with the increase in heat input. The microstructure of the simulated intercritical heat affected zone (ICHAZ) was mainly composed of granular bainite and blocky martensite regardless of heat input. When the heat input increased, the toughness of the simulated CGHAZ and ICHAZ continuously decreased. Nevertheless, the simulated FGHAZ still displayed good toughness (53.16 J) due to its fine structure. The occurrence of martensite-austenite (M-A) constituents was the main reason for the decrease in crack initiation energy of the simulated CGHAZ and ICHAZ at high values of heat input, and the toughness deteriorated as the size of M-A constituents increased. It should be noted that high-misorientation packet and block boundaries can effectively deviate or arrest the propagation of microcracks. When the heat input was in the approximate range of 8.63-14.95 kJ cm{sup −1}, all of the simulated subregions exhibited good toughness.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Influence of processing on secondary phase formation and microstructural evolution at U-10Mo alloy and Zr interlayer interfaces

Thermo-mechanical processing of uranium-10 wt. % molybdenum (U-10Mo) fuel plates leads to microstructure changes at the U-10Mo/Zr interfaces. Secondary phases formed at this interface are particularly important to interfacial bond strength, process optimization, and maintaining structural integrity of the U-10Mo fuel plates during irradiation. In this work, we determined the phases and phase transformation products occurring at the interface of the U-10Mo fuel and Zr interlayer when the fuel plate is subjected to short and long hot isostatic pressure times. Interfacial morphology, structure and composition of phases formed, and relative hardness across the U-10Mo/Zr interfaces were studied using a multi-length scale, multi-modal characterization approach involving electron microscopy, atom probe tomography, and atomic force microscopy. Here, results highlight that the extent of phase transformations, secondary phase formation, and hardness variability across interfaces can be controlled by modifying processing parameters. Phase diagram construction and thermodynamic calculations were performed using the Thermocalc software to identify expected phases formed at interfaces during the maximum hold temperature of 560 °C experienced during HIP.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2019

Microstructure Evolution and Stress Corrosion Cracking Susceptibility of 12Cr Martensitic Steel Upon Long-Term Service in Power Plants

After 230,000-h long-term service at 550 °C/13.7 MPa, the microstructure of a kind of 12Cr martensitic steel was investigated using scanning electron microscopy, backscattering electron microscope and x-ray diffraction analysis. The results show that the precipitation and coarsening of carbides at grain/lath boundaries are the main cause of microstructure degradation. The static immersion tests and the slow strain rate test coupled with electrochemical impedance spectroscopy were conducted on the served steel in 1.0% NaCl solution, and it turns out that the pitting corrosion resistance and repassivation ability of the steel are significantly reduced as a result of microstructure degradation. The stress corrosion cracking susceptibility of the steel was also studied. Fracture morphology analysis shows that the secondary crack in conjunction with slip lines is a result of the coalescence of micro-cracks nucleated from the pits.

36 MATERIALS SCIENCE↗
DOE OSTI2019

An Investigation on Microstructure Evolution, Mechanical Properties, and Strain Aging of Mg-1.8Zn-0.7Si-0.4Ca Biomedical Alloy Processed by Equal Channel Angular Pressing

The influence of equal channel angular pressing (ECAP) on microstructure and mechanical behavior, as well as, strain aging during ECAP and post-ECAP of Mg-1.8Zn-0.7Si-0.4Ca biomedical alloy was examined. The alloy in solid solution heat-treated condition was processed by ECAP with route B{sub C} at 350 and 400 °C. The specimens ECAPed at 350 °C were aged at 125 and 150 °C for different times. The hardness and shear punch test results indicated that performing ECAP at 350 °C for 4 passes increases the hardness and shear strength of the alloy from 48 HV and 110 MPa to 71 HV and 188 MPa, respectively. It was revealed that the average grain size of the alloy decreases from 78 µm to about 3 µm after 4 passes of ECAP. Three precipitates of CaMgSi, Ca{sub 2}Mg{sub 6}Zn{sub 3}, and Mg{sub 2}Si were detected in the solid solution specimen. After 4 passes of ECAP at 350 °C, Ca{sub 2}Mg{sub 6}Zn{sub 3} was completely dissolved and the morphology of Mg{sub 2}Si changed from Chinese script to fiber-shaped particles. Dynamic strain aging occurred at high-temperature ECAP, and the specimens were overaged during post-ECAP aging. Small MgZn particles were detected in the overaged sample.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Microstructural evolutions, phase transformations and hard magnetic properties in polycrystalline Ce–Co–Fe–Cu alloys

This work focuses on systematic studies of Ce–Co based 1:5 permanent magnet alloys of CeCo 4.4-x Fe x Cu 0.6 and CeCo 3.9-x Fe x Cu 1.2 (x = 0, 0.3, 0.6, 0.9, 1.2, 1.8) by varying Co:Fe. The overarching aim of this manuscript is to elucidate the hard-magnetic properties through a better understanding of phase formation by the structural, microstructural, and magnetic properties in these materials. Improved mutual solubility of Fe in the 1:5 phase has been observed with an extended homogeneity range by Cu substitution. For both composition series, Fe contents of x ≤ 0.6 show a homogeneous microstructure with a single 1:5 phase and good magnetic properties. The composition region 0.6 < x ≤ 0.9 appears to be near the boundary of solubility and evolution of other phases. At x = 1.8, it is found that the homogeneous 1:5 phase and magnetic hardness deteriorated due to the evolution of secondary phases such as 2:17, 2:7, and Fe–Co. Furthermore, the addition of Fe improved both the magnetization and Curie temperature via increased effective exchange interactions, while an increase in Cu content enhanced coercivity.

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2020

Effect of heat treatment on microstructural evolution and hardness homogeneity in laser powder bed fusion of alloy 718

The thermal history developed in laser powder bed fusion (LPBF) processes has been shown to be complex resulting in equally complex microstructures and mechanical properties. Microscopic observations and Vickers micro-hardness mapping measurements were carried out on diff ;erent section planes of LPBF alloy 718 cuboids. Three-dimensional finite element analysis was used to simulate thermal history and to predict the residual stress distribution in the as-built material. Computational thermodynamics was used to predict the micro-segregation and nucleation driving force of various phases in the bulk and in segregated regions. Varied heat-treatments such as simulated hot isostatic pressing, and double aging were applied. Their influence on the microstructure, microsegregation, precipitate formation, and micro-hardness variations of LPBF alloy 718 were investigated. Hardness map results showed heterogeneous micro-hardness on the xy- and xz-planes of the as-built parts where the bottom plane and center regions had larger hardness of ~315 HV 0.5 while the top plane and contours showed hardness of ~300 HV 0.5 . It was found that the aging treatment increased the overall hardness of the as-built condition from ~310 HV 0.5 to 470 HV 0.5 but also increased the hardness gradient throughout the coupon. After simulated hot isostatic pressing process (i.e., without applied pressure) at 1020 °C for 4 h followed by water quench (HIPWQ), the hardness gradient and hardness was minimized (~210 HV 0.5 ) as the microstructure transitioned from heterogeneous columnar grains in the as-built condition to more uniform recrystallized grains. A double aging treatment was applied to enhance hardness from ~210 HV 0.5 to ~440 HV 0.5 . Finally, HIPWQ followed by double aging produced a homogeneous microstructure and more uniform hardness map with enhanced mechanical properties in LPBF alloy 718 coupons.

36 MATERIALS SCIENCE↗
DOE OSTI2026

From Cryogenic to High Temperatures: A Microstructural Evolution of δ-phase Pu-Ga Alloys Investigated by Time-of-Flight High-resolution Neutron Diffraction

Phase stability and phase transformations in binary Pu alloys are critical for multiple applications. Long-term phase stability affects mechanical properties, microstructure, corrosion behavior, and structural integrity. A clear and detailed understanding of phase transformations and phase stability mechanisms is necessary to assess the behavior and response to unexpected stimuli. Gaining advanced knowledge on the behavior of Pu and Pu alloys at a variety of temperatures, pressures, and time will ensure better predictions and control on evolution outside laboratory measurements.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Microstructure Evolution and Mechanical Properties of the AZ91 Magnesium Alloy with Sr and Ti Additions in the As-Cast and As-Aged Conditions

Effect of different amounts of Sr and Ti additions with T6 heat treatment on microstructure and mechanical properties of the AZ91 alloy was investigated. The microstructure of the AZ91 alloy is consisted of the α-Mg phase surrounded by the semicontinuous network of β-Mg{sub 17}Al{sub 12} intermetallics. The average grain size and volume fraction of β phase decreased up to 1 wt.% Sr and 0.1 wt.% Ti additions. Exceeding Ti additions led to increase in both grain size and volume fraction. It was found that the grain refinement mechanism of AZ91 alloys with Sr additions was grain restriction factor. Also, 0.1 wt.% Ti addition could refine the grain structure of the AZ91 alloy by the formation of Al{sub 3}Ti particles that act as nucleation sites for the α-Mg phase. Furthermore, adding 1 wt.% Sr and 0.1 wt.% Ti enhanced the hardness values for both cast and aged AZ91 alloy. Moreover, ultimate tensile strength and tensile elongation values reached their maximum amounts with the 0.5 wt.% Sr and 0.1 wt.% Ti additions and more Sr and Ti additions deteriorated the mechanical properties of cast and aged AZ91 alloys. The fracture surface characterizations had good relations with the tensile properties. The fracture modes were cleavage and quasi-cleavage in the cast and aged AZ91 alloys. Furthermore, the optimum levels of Sr and Ti additions altered the fracture modes to more quasi-cleavage fractures.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Microstructure Evolution and Improved Creep Behavior of Mg-Al-Si Alloy Matrix Composite Reinforced with SiC Nanoparticles

The Mg-9Al-1Si matrix composite reinforced with SiC nanoparticles is fabricated by semisolid stirring-assisted ultrasonic vibration, which contains finer grains and a more uniform microstructure compared to that of the Mg-9Al-1Si alloys. The sizes of the Mg{sub 17}Al{sub 12} and Mg{sub 2}Si phases decreased continuously as the volume fraction of n-SiCp increased from 0 to 1% and then increased apparently when the volume fraction of n-SiCp increased to 1.5%. The steady-creep rates of the 1 vol.% n-SiCp/Mg-9Al-1Si are approximately two times lower than those of the Mg-9Al-1Si matrix alloy at 200 °C under applied stress of 70 MPa due to the strengthening effect of the nanosized SiCp. The reason for the improved creep properties is mainly attributed to the obvious grain boundary strengthening, the Orowan strengthening mechanism, the load transfer effect, and the pinning effect of the n-SiCp and the refined Mg{sub 17}Al{sub 12} and Mg{sub 2}Si phases.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Elevated temperature microstructure evolution of a medium-entropy CrCoNi superalloy containing Al,Ti

A new medium-entropy superalloy was produced based on the compositions of equiatomic CrCoNi and Ni-base superalloy Inconel 740H. Initial alloy design was performed using Thermo-Calc. The aging response and microstructural stability were assessed following heat treatment at temperatures between 600 and 900 °C and durations up to 100 h. Aging from a fully recrystallized state resulted in negligible grain growth and produced γ’ and σ phases. The same phases were present after aging from a cold-rolled state, but partially recrystallized microstructures resulted in multi-modal size distributions and heterogeneous spatial arrangements. Finally, room temperature hardness measurements were used to correlate aging conditions with quantitative precipitate measurements and mechanical properties.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Microstructure Evolution of Ultra-Fine-Grained AZ31 B Magnesium Alloy Produced by Submerged Friction Stir Processing

Ten-millimeter-thick strain-hardened AZ31B-H24 magnesium sheets were subjected to friction stir processing (FSP) in air and submerged friction stir processing (SFSP) under water to investigate their microstructures and microhardness properties. Different rotational speeds of 500, 630, 800, and 1000 rpm and traverse speeds of 50, 100, 200, and 350 mm/min were employed for processing the materials. For SFSPed samples, the rotational speed of 500 rpm and 200 mm/min of traverse speed resulted in an ultra-fine-grained structure with a minimum grain size of about 400-500 nm, which is half compared to that of FSPed. It was found that both processes led to variation of crystallographic orientation, and enhancing the rotational speed and lowering the traverse speed promoted the development of a {0002} basal texture. The microhardness of SFSPed material increased significantly up to 110% (~ 95 Hv), while the microhardness was 45% (~ 65 Hv) higher than the base metal (~ 45 Hv) for FSPed material.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Microstructural evolution in Cu-Nb processed via friction consolidation

Immiscible alloys, whether in well-mixed or layered forms, are of increasing interest based on their novel structural and functional properties, such as enhanced thermal stability against grain growth or radiation-induced defect trapping at the interfaces. To address the need for new approaches to tailor microstructures, the microstructural development of an immiscible Cu-Nb alloy processed via friction consolidation of elemental powders is investigated. Friction consolidation is a solid-phase processing technique that imparts severe plastic strain into a deforming volume resulting in elevated temperatures below the melting temperature of the alloy. Two distinct processing pathways were chosen to understand the effect of thermomechanical conditions on the final microstructure. The microstructure was characterized using scanning electron microscopy, scanning transmission electron microscopy, and X-ray diffraction techniques. Path 1 exhibited larger strain, strain rate, and temperature as compared with path 2. In path 1, agglomerated Nb particles were present in the recrystallized ultrafine-grained Cu matrix, while in path 2 extremely fine and dispersed Nb particles were present in a highly deformed Cu matrix. In both pathways, supersaturation of Cu in Nb lattices was noted, but not vice-versa. The asymmetry in mixing is explained based on deformation-based, thermodynamic and kinetic factors. These findings provide a pathway for creation of novel tailored microstructures and improved properties in any number of binary immiscible alloy systems.

Cu-Nb alloys, Microstructural refinement, Friction↗
DOE OSTI2024

Report on the Integration of Experimental and Modeling Data for Initial Equivalence Study of Microstructural Evolution in Irradiated LPBF 316SS

Advanced materials and manufacturing technologies are poised to improve the safety and design characteristics of nuclear technologies and meet US energy, environmental, and economic needs. In particular, metal additive manufacturing (AM) provides an opportunity to produce novel materials and component geometries, but their use is not without hurdles arising from the inherent microstructure variability that can result from the layer-by-layer build approach. Given the greater possible microstructure variability in AM materials—and the dearth of materials test reactors—it is impractical to rely solely on neutron irradiation studies to produce data for materials qualification for every possibility. This work within the Advanced Materials and Manufacturing Technologies (AMMT) Environmental Effects technical area contributes to the rapid qualification framework by developing a science-driven framework for the accelerated qualification of materials for nuclear environments. A key product of the Environmental Effects technical area of the AMMT program is the Licensing Approach with Ions and Neutrons (LAIN). This approach recognizes that whether using existing materials in new environments, newly developed materials tailored for these environments, or new manufacturing methods, the traditional decades-long approach for materials qualification does not facilitate rapid deployment. In FY 2023, the AMMT program presented a conceptual framework of specific steps to fulfill several technical challenges associated with qualifying materials for performance in radiation environments on an accelerated time frame informed by the state of the art in materials science and a review of the current regulatory landscape. The objective of this section of the Environmental Effects technical area is to critically evaluate and refine the proposed qualification framework presented under AMMT by integrating the research results of the neutron irradiations, the ion irradiations, and modeling efforts. These ongoing efforts span across Argonne National Laboratory (ANL), Idaho National Laboratory (INL), and Oak Ridge National Laboratory (ORNL) and are closely coordinated.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Microstructure evolution during near- T g annealing and its effect on shear banding in model alloys

By performing extensive molecular dynamics simulations, we investigate herein the deformation behavior in A l 90 S m 10 and C u 64.5 Z r 35.5 alloys after elongated isothermal annealing in the vicinity of the glass-transition temperature ( T g ). Different microstructural response to the annealing process was observed: A l 90 S m 10 maintains the glassy structure with improved energetic stability, enhanced short-range order (SRO), and a more pronounced spatial network that extends beyond the first atomic shell, while C u 64.5 Z r 35.5 forms nanocrystalline Laves C u 2 Zr phases. Shear banding occurs in both annealed systems under shear loading. For A l 90 S m 10 , the spatial network formed by the local clusters characterizing the SRO of the system is significantly weakened but remains appreciable in the shear band. In contrast, the crystalline ordering in the C u 64.5 Z r 35.5 is completely destroyed during shear banding. Consequently, while displaying higher yield strength, the annealed C u 64.5 Z r 35.5 sample appears to be less ductile. By carefully examining the effect of microstructures on the structural ordering in the shear band and the consequent mechanical response, our work contributes to a better understanding of the deformation mechanism of amorphous alloys as compared with that in crystalline materials.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗