Results for “Mesh Generation” — Page 8

NASA NTRS2019

CFD Evaluation of Lean-Direct Injection Combustors for Commercial Supersonics Technology

An overview is given of an effort that focused on using CFD analysis to complement design and configuration definition of Lean-Direct Injection (LDI) combustion concepts for NASA's Commercial Supersonic Transport (CST) program. The National Combustion Code (OpenNCC) was used to perform non-reacting and two-phase reacting flow computations for second and third generation LDI configurations at CST cruise conditions. All computations were performed with a consistent approach of mesh-generation, spray modeling, ignition and kinetics modeling. Emissions (EINOx) characteristics were predicted for CST cruise conditions, and compared with emissions data from experimental measurements to evaluate the fidelity of the CFD modeling approach to predict emissions changes in response to changes in supersonic cycle conditions.

nitrogen oxides injectors↗

NASA NTRS2019

CFD Evaluation Of Lean-Direct Injection Combustors for Commercial Supersonics Technology

An overview is given of an effort that focused on using CFD analysis to complement design and configuration definition of Lean-Direct Injection (LDI) combustion concepts for NASA's Commercial Supersonic Transport (CST) program. The National Combustion Code (OpenNCC) was used to perform non-reacting and two-phase reacting flow computations for second and third generation LDI configurations at CST cruise conditions. All computations were performed with a consistent approach of mesh-generation, spray modeling, ignition and kinetics modeling. Emissions (EINOx) characteristics were predicted for CST cruise conditions, and compared with emissions data from experimental measurements to evaluate the fidelity of the CFD modeling approach to predict emissions changes in response to changes in supersonic cycle conditions.

Ajmani, Kumud↗

NASA NTRS1989

Unstructured mesh solution of the Euler and Navier-Stokes equations

Mesh generation procedures as well as solution algorithms for solving the Euler and Navier-Stokes equations on unstructured meshes are presented. The solution algorithms discussed utilize approximate Riemann solver, upwind differencing to achieve high spatial accuracy. Numerical results for Euler flow over single and multi-element airfoils are presented.

Barth, Timothy J.↗

NASA NTRS1993

surf3d: A 3-D finite-element program for the analysis of surface and corner cracks in solids subjected to mode-1 loadings

A computer program, surf3d, that uses the 3D finite-element method to calculate the stress-intensity factors for surface, corner, and embedded cracks in finite-thickness plates with and without circular holes, was developed. The cracks are assumed to be either elliptic or part eliptic in shape. The computer program uses eight-noded hexahedral elements to model the solid. The program uses a skyline storage and solver. The stress-intensity factors are evaluated using the force method, the crack-opening displacement method, and the 3-D virtual crack closure methods. In the manual the input to and the output of the surf3d program are described. This manual also demonstrates the use of the program and describes the calculation of the stress-intensity factors. Several examples with sample data files are included with the manual. To facilitate modeling of the user's crack configuration and loading, a companion program (a preprocessor program) that generates the data for the surf3d called gensurf was also developed. The gensurf program is a three dimensional mesh generator program that requires minimal input and that builds a complete data file for surf3d. The program surf3d is operational on Unix machines such as CRAY Y-MP, CRAY-2, and Convex C-220.

Raju, I. S.↗

NASA NTRS2016

Preliminary Computational Study for Future Tests in the NASA Ames 9 foot' x 7 foot Wind Tunnel

The NASA Advanced Air Vehicles Program, Commercial Supersonics Technology Project seeks to advance tools and techniques to make over-land supersonic flight feasible. In this study, preliminary computational results are presented for future tests in the NASA Ames 9 foot x 7 foot supersonic wind tunnel to be conducted in early 2016. Shock-plume interactions and their effect on pressure signature are examined for six model geometries. Near- field pressure signatures are assessed using the CFD code USM3D to model the proposed test geometries in free-air. Additionally, results obtained using the commercial grid generation software Pointwise Reigistered Trademark are compared to results using VGRID, the NASA Langley Research Center in-house mesh generation program.

Pearl, Jason M.↗

NASA NTRS1996

Generating Voronoi Diagrams for Curved Shapes with Divide-and-Conquer

Voronoi diagrams have been used in many practical applications including solid modeling, Numerical Control machining, Finite Element mesh generation, etc. Investigating the properties of these diagrams is an active research topic with many fruitful results. Computational techniques for Voronoi diagrams, however, have been concentrated on low order elements, for points, lines, polygons, quadratic curves and surfaces. This paper presents a divide-and-conquer scheme computing the diagrams for planar shapes bounded by closed curves commonly encountered in Computer Aided Design. These curves include analytical curves and splines. The algorithm first divides the boundary curve into sections, delimited by curve points with the minimal curvatures. Bisector branches for these sections are then generated and merged recursively to obtain the final diagram. A detailed example in the paper shows the steps of the generation and merging of the bisectors. A simple analysis of the complexity of the algorithm is also presented.

Chou, Jin J.↗

NASA NTRS1999

On the Use of CAD-Native Predicates and Geometry in Surface Meshing

Several paradigms for accessing computer-aided design (CAD) geometry during surface meshing for computational fluid dynamics are discussed. File translation, inconsistent geometry engines, and nonnative point construction are all identified as sources of nonrobustness. The paper argues in favor of accessing CAD parts and assemblies in their native format, without translation, and for the use of CAD-native predicates and constructors in surface mesh generation. The discussion also emphasizes the importance of examining the computational requirements for exact evaluation of triangulation predicates during surface meshing.

Aftosmis, M. J.↗

NASA NTRS1995

Prospects and expectations for unstructured methods

The last decade has witnessed a vigorous and sustained research effort on unstructured methods for computational fluid dynamics. Unstructured mesh generators and flow solvers have evolved to the point where they are now in use for design purposes throughout the aerospace industry. In this paper we survey the various mesh types, structured as well as unstructured, and examine their relative strengths and weaknesses. We argue that unstructured methodology does offer the best prospect for the next generation of computational fluid dynamics algorithms.

Baker, Timothy J.↗

NASA NTRSDate not supplied

GT2024-139262: Development of a Computational Fluid Dynamics Model for a High-Speed Centrifugal Compressor

Computational fluid dynamics (CFD) has become widely used in the design and analysis of turbomachinery components such as centrifugal compressors. However, CFD is only a limited representation of experimental cases and struggles to model complex flows or lack model details to increase computation speed. The High Efficiency Centrifugal Compressor (HECC) was designed by United Technologies Research Center for NASA to investigate the difficulties behind improving centrifugal compressor technology and to provide an open case to the turbomachinery research community. The CFD technology seen in previous numerical models of the compressor have improved since then. In this study, a high-fidelity computational model for the vaneless configuration of HECC operating at its design point was developed and compared to an equivalent experimental case. This model incorporated GPU versions of mesh generation code WAND and solver code LEO from AeroDynamic Solutions, Inc. Blade sections extracted from the solid model formed the basis of the impeller mesh, while the remainder of the stage was modeled as ducts. Standard day aerodynamic conditions, design rotational speed, design mass flow rate, and inlet flow angles served as additional inputs. A mesh sensitivity study was performed prior to using the model for analysis. The accuracy of the model’s predictions of impeller and stage performance were assessed by comparing the total pressure ratio, total temperature rise ratio, and adiabatic efficiency to the corresponding parameters observed in the experimental case. Results showed a general overprediction of compressor performance by the model. Predictions were more accurate for the impeller performance compared to those for the full compressor stage. Spanwise analyses showed that the model tended to follow flow behavior patterns exhibited in the experiment. Beyond this study, this model was used to examine HECC aerodynamics and performance in research following thereafter.

centrifugal compressor↗

NASA NTRS2008

Domain Decomposition By the Advancing-Partition Method

A new method of domain decomposition has been developed for generating unstructured grids in subdomains either sequentially or using multiple computers in parallel. Domain decomposition is a crucial and challenging step for parallel grid generation. Prior methods are generally based on auxiliary, complex, and computationally intensive operations for defining partition interfaces and usually produce grids of lower quality than those generated in single domains. The new technique, referred to as "Advancing Partition," is based on the Advancing-Front method, which partitions a domain as part of the volume mesh generation in a consistent and "natural" way. The benefits of this approach are: 1) the process of domain decomposition is highly automated, 2) partitioning of domain does not compromise the quality of the generated grids, and 3) the computational overhead for domain decomposition is minimal. The new method has been implemented in NASA's unstructured grid generation code VGRID.

Pirzadeh, Shahyar Z.↗

NASA NTRS2009

Domain Decomposition By the Advancing-Partition Method for Parallel Unstructured Grid Generation

A new method of domain decomposition has been developed for generating unstructured grids in subdomains either sequentially or using multiple computers in parallel. Domain decomposition is a crucial and challenging step for parallel grid generation. Prior methods are generally based on auxiliary, complex, and computationally intensive operations for defining partition interfaces and usually produce grids of lower quality than those generated in single domains. The new technique, referred to as "Advancing Partition," is based on the Advancing-Front method, which partitions a domain as part of the volume mesh generation in a consistent and "natural" way. The benefits of this approach are: 1) the process of domain decomposition is highly automated, 2) partitioning of domain does not compromise the quality of the generated grids, and 3) the computational overhead for domain decomposition is minimal. The new method has been implemented in NASA's unstructured grid generation code VGRID.

Pirzadeh, Shahyar Z.↗

NASA NTRSDate not supplied

HLPW-5: Overview and Workshop Summary

The Fifth AIAA CFD High-Lift Prediction Workshop was held with the goal of assessing the numerical prediction capability of current-generation computational fluid dynamics (CFD) technology for swept, medium/high-aspect-ratio wings in high-lift configurations. A key aspect of this endeavor was the use of Technology Focus Groups (TFG), which included both mesh generation and flow-solver experts working together to accelerate advancements for their particular CFD methodology, by addressing key questions of importance prior to the workshop. The high-lift version of the NASA Common Research Model (CRM-HL) configuration was the focus of this workshop, and was used for three unique test cases. Wind-tunnel data were available for comparison for one of the test cases. Altogether, 365 datasets of CFD results were submitted by 47 teams, with 41 teams contributing to the multiple configurations of Case 1, 40 to Case 2, and 18 to Case 3. This paper provides a high-level summary of the results and conclusions from the workshop. As concluded from past workshops, fixed-grid Reynolds-averaged Navier-Stokes methods continued to be inaccurate and inconsistent for high-lift flows near maximum lift. However, application of mesh-adaptation technology helped to achieve improved consistency. Scale-resolving methods appeared most promising for predicting high-lift flow physics, particularly at maximum lift. Best practices for these methods were refined over the course of the workshop and new challenges were identified.

Adam M Clark↗

NASA NTRSDate not supplied

Pterodactyl: Aerodynamic and Aerothermal Modeling for a Symmetric Deployable Earth Entry Vehicle with Flaps

NASA’s Pterodactyl project has investigated a deployable atmospheric entry vehicle integrated with a flap control system that provides precision targeting during reentry. The control system consists of eight flaps mounted at the edge of a heatshield that can deflect in and out of the flow. An aerodynamic and aerothermodynamic analysis process was developed for preliminary vehicle design and aerodynamic database generation using engineering and CFD tools with varying levels of fidelity. The objective of this analysis was to: 1) understand the inherent aerodynamics, 2) provide an aerodynamics database for stability and control analysis, and 3) provide qualitative and quantitative aeroheating analysis for Thermal Protection System modeling of the flaps. A high fidelity Euler code, Cart3D, was used to resolve complex flow features such as secondary shocks and shock impingement. A wide range of supersonic (Mach 2) and hypersonic Mach numbers (up to Mach 40) were tested with an Earth atmosphere model. A process was developed to utilize the adaptive volume mesh generator utility of the perfect gas model of Cart3D to create meshes with high cell efficiency and numerical stability prior to running a 2nd order accurate solution with a real gas model. High-fidelity aerothermal CFD simulations were performed using US3D to further improve the aerothermal analysis on hypersonic flow around a complex entry vehicle shape including viscosity, chemical reactions of air species, vibrational energy, and catalytic surface reactions. In this process, it was found that the flap control system provided multi-axis control that can be utilized for entry precision targeting. Additionally, the Pterodactyl vehicle can achieve up to a trim L/D of 0.2. Finally, the increased fidelity of the aerothermal heating environments revealed that the shear stress contributes to increasing the heating on the flaps.

Deployable Entry Vehicle↗

NASA NTRSDate not supplied

Pterodactyl: Aerodynamic and Aerothermal Modeling for a Symmetric Deployable Earth Entry Vehicle with Flaps

NASA’s Pterodactyl project has investigated a deployable atmospheric entry vehicle integrated with a flap control system that provides precision targeting during reentry. The control system consists of eight flaps mounted at the edge of a heatshield that can deflect in and out of the flow. An aerodynamic and aerothermodynamic analysis process was developed for preliminary vehicle design and aerodynamic database generation using engineering and CFD tools with varying levels of fidelity. The objective of this analysis was to: 1) understand the inherent aerodynamics, 2) provide an aerodynamics database for stability and control analysis, and 3) provide qualitative and quantitative aeroheating analysis for Thermal Protection System modeling of the flaps. A high fidelity Euler code, Cart3D, was used to resolve complex flow features such as secondary shocks and shock impingement. A wide range of supersonic (Mach 2) and hypersonic Mach numbers (up to Mach 40) were tested with an Earth atmosphere model. A process was developed to utilize the adaptive volume mesh generator utility of the perfect gas model of Cart3D to create meshes with high cell efficiency and numerical stability prior to running a 2nd order accurate solution with a real gas model. High-fidelity aerothermal CFD simulations were performed using US3D to further improve the aerothermal analysis on hypersonic flow around a complex entry vehicle shape including viscosity, chemical reactions of air species, vibrational energy, and catalytic surface reactions. In this process, it was found that the flap control system provided multi-axis control that can be utilized for entry precision targeting. Additionally, the Pterodactyl vehicle can achieve up to a trim L/D of 0.2. Finally, the increased fidelity of the aerothermal heating environments revealed that the shear stress contributes to increasing the heating on the flaps.

Deployable Entry Vehicle↗

NASA NTRS1993

Massively parallel computation of RCS with finite elements

One of the promising combinations of finite element approaches for scattering problems uses Whitney edge elements, spherical vector wave-absorbing boundary conditions, and bi-conjugate gradient solution for the frequency-domain near field. Each of these approaches may be criticized. Low-order elements require high mesh density, but also result in fast, reliable iterative convergence. Spherical wave-absorbing boundary conditions require additional space to be meshed beyond the most minimal near-space region, but result in fully sparse, symmetric matrices which keep storage and solution times low. Iterative solution is somewhat unpredictable and unfriendly to multiple right-hand sides, yet we find it to be uniformly fast on large problems to date, given the other two approaches. Implementation of these approaches on a distributed memory, message passing machine yields huge dividends, as full scalability to the largest machines appears assured and iterative solution times are well-behaved for large problems. We present times and solutions for computed RCS for a conducting cube and composite permeability/conducting sphere on the Intel ipsc860 with up to 16 processors solving over 200,000 unknowns. We estimate problems of approximately 10 million unknowns, encompassing 1000 cubic wavelengths, may be attempted on a currently available 512 processor machine, but would be exceedingly tedious to prepare. The most severe bottlenecks are due to the slow rate of mesh generation on non-parallel machines and the large transfer time from such a machine to the parallel processor. One solution, in progress, is to create and then distribute a coarse mesh among the processors, followed by systematic refinement within each processor. Elimination of redundant node definitions at the mesh-partition surfaces, snap-to-surface post processing of the resulting mesh for good modelling of curved surfaces, and load-balancing redistribution of new elements after the refinement are auxiliary steps expected to result in a robust low i/o system for very large finite element problems.

Parker, Jay↗

NASA NTRS1996

Meshing of a Spiral Bevel Gearset with 3D Finite Element Analysis

Recent advances in spiral bevel gear geometry and finite element technology make it practical to conduct a structural analysis and analytically roll the gearset through mesh. With the advent of user specific programming linked to 3D solid modelers and mesh generators, model generation has become greatly automated. Contact algorithms available in general purpose finite element codes eliminate the need for the use and alignment of gap elements. Once the gearset is placed in mesh, user subroutines attached to the FE code easily roll the gearset through mesh. The method is described in detail. Preliminary results for a gearset segment showing the progression of the contact lineload is given as the gears roll through mesh.

Bibel, George D.↗

NASA NTRS1994

Computational Approaches to Vestibular Research

The Biocomputation Center at NASA Ames Research Center is dedicated to a union between computational, experimental and theoretical approaches to the study of neuroscience and of life sciences in general. The current emphasis is on computer reconstruction and visualization of vestibular macular architecture in three-dimensions (3-D), and on mathematical modeling and computer simulation of neural activity in the functioning system. Our methods are being used to interpret the influence of spaceflight on mammalian vestibular maculas in a model system, that of the adult Sprague-Dawley rat. More than twenty 3-D reconstructions of type I and type II hair cells and their afferents have been completed by digitization of contours traced from serial sections photographed in a transmission electron microscope. This labor-intensive method has now been replace d by a semiautomated method developed in the Biocomputation Center in which conventional photography is eliminated. All viewing, storage and manipulation of original data is done using Silicon Graphics workstations. Recent improvements to the software include a new mesh generation method for connecting contours. This method will permit the investigator to describe any surface, regardless of complexity, including highly branched structures such as are routinely found in neurons. This same mesh can be used for 3-D, finite volume simulation of synapse activation and voltage spread on neuronal surfaces visualized via the reconstruction process. These simulations help the investigator interpret the relationship between neuroarchitecture and physiology, and are of assistance in determining which experiments will best test theoretical interpretations. Data are also used to develop abstract, 3-D models that dynamically display neuronal activity ongoing in the system. Finally, the same data can be used to visualize the neural tissue in a virtual environment. Our exhibit will depict capabilities of our computational approaches and some of our findings from their application. For example, our research has demonstrated that maculas of adult mammals retain the property of synaptic plasticity. Ribbon synapses increase numerically and undergo changes in type and distribution (p<0.0001) in type II hair cells after exposure to microgravity for as few as nine days. The finding of macular synaptic plasticity is pertinent to the clinic, and may help explain some. balance disorders in humans. The software used in our investigations will be demonstrated for those interested in applying it in their own research.

Ross, Muriel D.↗

NASA NTRS1994

High-performance parallel analysis of coupled problems for aircraft propulsion

This research program deals with the application of high-performance computing methods for the analysis of complete jet engines. We have entitled this program by applying the two dimensional parallel aeroelastic codes to the interior gas flow problem of a bypass jet engine. The fluid mesh generation, domain decomposition, and solution capabilities were successfully tested. We then focused attention on methodology for the partitioned analysis of the interaction of the gas flow with a flexible structure and with the fluid mesh motion that results from these structural displacements. This is treated by a new arbitrary Lagrangian-Eulerian (ALE) technique that models the fluid mesh motion as that of a fictitious mass-spring network. New partitioned analysis procedures to treat this coupled three-component problem are developed. These procedures involved delayed corrections and subcycling. Preliminary results on the stability, accuracy, and MPP computational efficiency are reported.

Felippa, C. A.↗