Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Material microstructure”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8
All sourcesNASA NTRSDOE OSTI
NASA NTRS2017

Chemical, Structural, and Microstructural Changes in Metallic and Silicon-Based Coating Materials Exposed to Iodine Vapor

The chemical, structural and microstructural behavior of steels (304, 316 and A36), titanium-aluminum alloy (Ti-Al, (6Al-4V)), aluminum-magnesium alloy (Al-Mg, 6061), and coatings (Silcolloy and Dursan (SilcoTek Corporation)) were probed after exposure to iodine laminar flow. Exposures were carried out in a custom-built Iodine Vapor RIG (IVR) at 300 degrees C to an iodine laminar vapor flow of 1 mg min(exp. -1), carried by 145 mL-min(exp. -1) argon gas, for 5, 15 and 30 days. Samples were characterized before and after the experiment by gravimetric analysis, X-ray diffraction (XRD) and cross section electron microscopy analysis coupled with energy dispersive X-ray spectroscopy (EDS). All steels exposed for 30 days formed scales consisting mainly of metal (Cr, Fe, Ni) oxides showing different chemistry, microstructure and crystalline phases. Elemental iodine was only detected by EDS analysis in the scales of stainless steels 304 and 316. After 30 days, the Ti-Al exhibited no detectable scale, suggesting only a very thin film was formed. A scale consisting mainly of aluminum, iodine, and oxygen formed on the Al-Mg sample exposed to 30 days. Some pockets rich in magnesium, iodine and oxygen also formed in this Al-Mg alloy. Stainless steel 316, low carbon steel A36 and Ti-Al alloy coated with Silcolloy and stainless steel 304 coated with Dursan that were exposed for 30 days exhibited no oxidation. Stainless steel 304 coated with Silcolloy exposed for 30 days did not exhibit corrosion although the sample gained weight and the coating exhibited expansion. The weight gain per area performance of the materials exposed in iodine lamina flow containing oxygen at impurity level for 10, 15 and 30 days are reported from the lowest to the highest weight gain per area as follows: Steels: Less than 316 less than 304 less than A36; Ti-Al-Mg based alloys: Al-Mg less than Ti-Al: Considering the experimental uncertainties, no weight change was observed for Stainless steel 316, low carbon steel A36 and Ti-Al alloy coated with Silcolloy and stainless steel 304 coated with Dursan. The corrosion of the alloys is catalyzed by iodine in the presence of oxygen as impurity.

Costa, Gustavo C. C.↗
NASA NTRS1990

Quantitative characterization of spatial distribution of particles in materials: Application to materials processing

Most engineering materials contain second phase particles or fibers which serve to reinforce the matrix phase. The effect of reinforcements on material properties is usually analyzed in terms of the average volume fraction and spacing of reinforcements, quantities which are global microstructural characteristics. However, material properties can also depend on local microstructural characteristics; for example, on how uniformly the reinforcing phase is distributed in the material. The analysis method will then be applied to a materials processing problem to discover how processing parameters can be selected to maximize redistribution of the reinforcing phase during processing. Several mathematical analysis methods could be adapted to the problem of characterizing the distribution of particles in materials. A tessellation-based method was selected. In the first phase of the investigation, a software package was written to automate the analysis. Typical results are shown. The analysis technique allows the degree to which particles are clustered together, the size and spacing of particle clusters, and the particle density in clusters to be found. The analysis methods were applied to computer-generated distributions and to a few real particle-containing materials. Methods for analyzing a nonuniform particle distribution in a material can be applied to two broad classes of materials science problems: understanding how the resulting particle distribution affects properties. The analysis method described is applied to a materials processing problem: how to select extrusion conditions to maximize the redistribution of reinforcing particles that are initially nonuniformly distributed. In addition, the tessellation-based method to analyze star distributions in spiral galaxies was adapted, illustrating the diverse types of problems to which the analysis method can be applied.

Parse, J. B.↗
NASA NTRS2019

Additive Manufacturing of Multi-Material Systems for Aerospace Applications

Additive manufacturing methods for producing single materials are rapidly improving. The resulting material properties and microstructures are becoming more comparable to those of conventionally fabricated materials. However, the need for multi-functional and complex structures and components requires additional innovations in manufacturing such as multi-material and hybrid additive manufacturing approaches. Additive manufacturing machines with multiple print capabilities and combinations of AM, machining, and conventional processing methods will further open up design spaces and possibilities. In this presentation, several examples of the needs and methods for multi-material fabrication will be discussed with a focus on aerospace applications. Direct printing of silver coils in conjunction with fused deposition modeling, machined parts, and, binder jetting is being developed for innovative stator designs. Binder jetting of silicon-based materials with powder bed additions is being developed for heat exchanger applications. Additive manufacturing of bi-material systems is being pursued to fabricate lightweight, integrated, multifunctional structures.

multi-materials↗
NASA NTRSDate not supplied

Predictive Modeling of Carbon Ablators

Efforts to build a Predictive Material Modeling (PMM) framework from the micro-scale to the macro-scale are presented in this abstract. To reduce the need for extensive testing, accelerate the design cycle process, and reduce uncertainty margins applied to final designs, NASA is developing simulation and modeling tools that enable characterization of material properties and response to high-enthalpy environments. The Porous Microstructure Analysis (PuMA) code has been developed for computing macroscale (volume averaged) properties of porous materials using microscale images from micro-computed tomography (micro-CT). Microscale modeling requires a realistic representation of a material microstructure; these are obtained either synthetically during the design of the material or through X-ray micro-CT. Volume averaged properties are then used to inform macroscale material response models, such as those implemented in the Porous-material Analysis Toolbox based on OpenFOAM (PATO) software, also actively developed by NASA. The computational model in PATO is a generic heat and mass transfer model for porous reactive materials containing several solid phases and a single gas phase. The detailed chemical interactions occurring between the solid phases and the gas phase are modeled at the pore scale assuming local thermal equilibrium. These tools were developed to efficiently interface with other pre-existing codes such as SPARTA (direct simulation Monte Carlo), DPLR (hypersonic CFD), NEQAIR (radiative transport) and DAKOTA (uncertainty quantification and optimization). Detailed flight data (Mars Science Laboratory [MSL] Entry Descent and Landing Instrument [MEDLI]) is critical for validating these computational tools for NASA applications. Examples of modeling ablative material response using these codes will be presented including 3D simulations of the full-scale heatshield of the MSL capsule. The simulations demonstrate the ability of the modern material response code, PATO, to handle the material response of geometrically complex and large domains, through the use of massively parallel computations.

Thermal Protection Systems↗
NASA NTRSDate not supplied

Predictive Modeling of Carbon Ablators Using Micro and Macro-Scale Modeling

Efforts to build a Predictive Material Modeling (PMM) framework from the micro-scale to the macro-scale are presented in this abstract. To reduce the need for extensive testing, accelerate the design cycle process, and reduce uncertainty margins applied to final designs, NASA is developing simulation and modeling tools that enable characterization of material properties and response to high-enthalpy environments. The Porous Microstructure Analysis (PuMA) code has been developed for computing macroscale (volume averaged) properties of porous materials using microscale images from micro-computed tomography (micro-CT). Microscale modeling requires a realistic representation of a material microstructure; these are obtained either synthetically during the design of the material or through X-ray micro-CT. Volume averaged properties are then used to inform macroscale material response models, such as those implemented in the Porous-material Analysis Toolbox based on OpenFOAM (PATO) software, also actively developed by NASA. The computational model in PATO is a generic heat and mass transfer model for porous reactive materials containing several solid phases and a single gas phase. The detailed chemical interactions occurring between the solid phases and the gas phase are modeled at the pore scale assuming local thermal equilibrium. These tools were developed to efficiently interface with other pre-existing codes such as SPARTA (direct simulation Monte Carlo), DPLR (hypersonic CFD), NEQAIR (radiative transport) and DAKOTA (uncertainty quantification and optimization). Detailed flight data (Mars Science Laboratory [MSL] Entry Descent and Landing Instrument [MEDLI]) is critical for validating these computational tools for NASA applications. Examples of modeling ablative material response using these codes will be presented including 3D simulations of the full-scale heatshield of the MSL capsule. The simulations demonstrate the ability of the modern material response code, PATO, to handle the material response of geometrically complex and large domains, through the use of massively parallel computations.

Thermal Protection Systems↗
NASA NTRS1991

Physical and chemical analysis of a Ni/H2 cell

A cycled aerospace nickel hydrogen (Ni/H2) cell was subjected to destructive physical analysis to determine the reason for a capacity loss after 5,967 cycles at 60 percent depth of discharge. The positive plates in the cell were analyzed in terms of chemical composition, active material utilization, charge efficiency, and thickness increase. The microstructure of a cross section of the positive plate was determined by backscattered electron image analysis. The results suggest that the capacity loss in the cell is caused by low charge acceptance and low active material utilization at the positive plate. The oxidized nickel species content of the positive plate increased due to corrosion of the nickel sintered skeleton. This appears to circumvent the orderly reaction of the active material. Microstructural analysis has indicated that a new phase of active material is formed with cycling.

H Vaidyanathan↗
NASA NTRS2019

Microscale Analysis of Spacecraft Heat Shields

Imagine entering Earth’s atmosphere after returning from the outer solar system. A heat shield less than 2 inches thick protects you from temperatures up to 2,900° Celsius (5,252° Fahrenheit). Such conditions were experienced by NASA’s Stardust capsule during reentry in 2006. The only materials capable of providing the necessary protection are composites with complex microstructures. Evaluating these materials is difficult, requiring precise knowledge of their properties. To this end, NASA scientists are developing research codes to compute material properties and simulate ablation at the microscale using agency supercomputers. Utilizing these tools, along with experiments, researchers are working to push the limits of spaceflight, allowing for greater flexibility in future space missions.

Thornton, John M.↗
NASA NTRS2018

Plasticity and Damage Modeling of Stress Asymmetry and Dynamic Behavior of AFS Additive Manufactured Aluminum Alloy 2219

The Solid State Additive Manufacturing (AM) process referred as MELD that fabricated the samples in this study, provides a new path for repairing, coating, joining and additive manufacturing metals and metal matrix composites. This research will be the first application of a physics-based microstructure dependent internal state variable (ISV) plasticity and damage material model to capture the mechanical response of an AM Aluminum Alloy (AA) 2219 via the MELD process. In this research, a microstructure-based internal state variable (ISV) plasticity-damage model was used to capture the mechanical behavior of AFS 2219 aluminum alloy. Aeroprobe Corporation, creator and patent holder for the MELD process, fabricated the material by pushing a solid filler rod of AA2219-T861 material through a hollow rotating tool onto an AA2219 T851 plate substrate. As feedstock, solid or powder precursor metals are pushed through a nonconsumable rotating cylindrical tool. Herein, added layers are deposited and metallurgically bonded to substrate material or previously deposited layers by the heat generated from the rotating tool through plastic deformation of the filler material. Once a layer has been added, the tool height increases, and starts the deposition of the next layer. This process results in beneficial properties such as grain refinement, homogenization and reduced porosity (fully dense). This process will experience temperatures similar to those in the weld nugget zone (WNZ) in friction stir welding (FSW), ranging from 0.6-0.9 Tm, with Tm being the melting point of the material. MELD is highly scalable with AA deposition rates reaching over 1000 cm3/hr, which allows for MELD being used for repairs, coatings, and building components. A motivating factor driving the research for physics-based history dependent material modeling of MELD components is the ability to accurately capture the stress-state and strain rate dependence in the material caused by variations in material microstructure from the MELD processing of new or repaired components. The ISV model incorporates microstructural content and is consistent with continuum level kinematics, kinetics, and thermodynamics. These features allow the ISV model to capture large deformations at the structural scale using the kinematic and isotropic hardening, while microscale damage is obtained from the microstructural features. The benefits of the ISV model arise from the inclusion of structure-property relationships identified from microstructural characterization and experimentation. The Bauschinger effect (BE) is an important concept, vital in the accurate prediction of cyclic stress-strain response of ductile materials such as metals. The ISV model has been successfully used to capture the behavior and damage, and the BE of different aluminum alloys and steels. The ISV model uses kinematic and isotropic hardening to help capture deformations of the material at the macro scale. To understand this hardening relationship, calculating the kinematic and isotropic hardening relationship in the material is warranted for a high-fidelity model. Electron Backscattered Diffraction (EBSD) was used to characterize the as-fabricated microstructure, where a fully-dense equiaxed grain morphology with average grain size of 2.5 μm was observed. Microhardness mapping of the as-built structures, monotonic tension and compression experiments at both quasi-static (0.001/s) strain rates, tension-followed-by-compression and compression-followed-by-tension experiments were performed to obtain the set of plasticity and damage constants necessary to capture strain rate and stress state behavior of this additive material. To calibrate the plasticity-damage model, a single set of constants were determined to capture the different stress states the MELD AA2219. One set of the constants was determined from experimental true stress-strain curves for the tension and compression data. Additionally, microstructural information and data from the open literature were used as the other model constants. This research is a first of its kind for AFS AA2219, includes correlating the ISV model to the monotonic experimental results that capture the isotropic and kinematic plasticity mechanical response.

Rivera, O. G.↗
NASA NTRS2010

Role of Microstructure on the Performance of UHTCs

We have investigated a number of methods to control microstructure. We have routes to form: a) in situ "composites" b) Very fine microstructures. Arcjet testing and other characterization of monolithic materials. Control oxidation through microstructure and composition. Beginning to incorporate these materials as matrices for composites. Modeling effort to facilitate material design and characterization.

Johnson, Sylvia M.↗
NASA NTRS2010

Microscopic Scale Simulation of the Ablation of Fibrous Materials

This slide presentation reviews the ablation by oxidation of carbon-fiber preforms impregnated in carbonized phenolic-formaldehyde matrix is modeled at microscopic scale. Direct numerical simulations show that the matrix ablates in volume leaving the carbon fibers exposed. This is due to the fact that the reactivity of carbonized phenolics is higher than the reactivity of carbon fibers. After the matrix is depleted, the fibers ablate showing progressive reduction of their diameter. The overall material recession occurs when the fibers are consumed. Two materials with the same carbon-fiber preform, density and chemical composition, but with different matrix distributions are studied. These studies show that at moderate temperatures (< 1000K) the microstructure of the material influences its recession rate; a fact that is not captured by current models that are based on chemical composition only. Surprisingly, the response of these impregnated-fiber materials is weakly dependent on the microstructure at very high temperatures (e.g., Stardust peak heating conditions: 3360K).

Lachaud, Jean↗
NASA NTRSDate not supplied

Bridging the Gap Between Microscale Modeling and Additive Manufacturing for TPS

An overview of the now open-source NASA ARC software PuMA will be provided. On top of the well-documented ability to import and compute material properties from micro-CT images, PuMA has the ability to design microstructures and compute/predict material properties such as: porosity, permeability, tortuosity, thermal and electrical conductivity, tensile strength, etc. Therefore, a whole new range of capabilities is available, and provides users with the ability to build TPS materials (both fibrous and woven types) and optimize their properties based on missions and requirements. This talk will aim to provide a seed to start bridging the gap between microscale modeling of TPS materials and additive manufacturing.

Conductivity↗
NASA NTRS1992

Metallurgy and properties of plasma spray formed materials

Understanding the fundamental metallurgy of vacuum plasma spray formed materials is the key to enhancing and developing full material properties. Investigations have shown that the microstructure of plasma sprayed materials must evolve from a powder splat morphology to a recrystallized grain structure to assure high strength and ductility. A fully, or near fully, dense material that exhibits a powder splat morphology will perform as a brittle material compared to a recrystallized grain structure for the same amount of porosity. Metallurgy and material properties of nickel, iron, and copper base alloys will be presented and correlated to microstructure.

Mckechnie, T. N.↗
NASA NTRS2010

Microscopic Scale Simulation of the Ablation of Fibrous Materials

Ablation by oxidation of carbon-fiber preforms impregnated in carbonized phenolic matrix is modeled at microscopic scale. Direct numerical simulations show that the carbonized phenolic matrix ablates in volume leaving the carbon fibers exposed. This is due to the fact that the reactivity of carbonized phenolic is higher than the reactivity of carbon fibers. After the matrix is depleted, the fibers ablate showing progressive reduction of their diameter. The overall material recession occurs when the fibers are consumed. Two materials with the same carbon-fiber preform, density and chemical composition, but with different matrix distributions are studied. These studies show that at moderate temperatures (< 1000 K) the microstructure of the material influences its recession rate; a fact that is not captured by current models that are based on chemical composition only. Surprisingly, the response of these impregnated-fiber materials is weakly dependent on the microstructure at very high temperatures (e.g., Stardust peak heating conditions: 3360K).

Lachaud, Jean Romain↗
NASA NTRS2018

Characterization of Titanium Alloys Produced by Electron Beam Directed Energy Deposition

Functionally graded materials offer the potential to improve structural efficiency by allowing the material composition and/or microstructural features to spatially vary within a component. Additive manufacturing techniques enable the fabrication of such graded materials and structures. While examining several titanium alloys, this paper focuses on Ti-8Al-1Er as it has a unique microstructure that is only feasible when produced by rapid solidification methods like electron beam directed energy deposition, an additive manufacturing process. The results show that, when mixed, Ti-8Al-1Er and commercially-pure titanium uniformly mix at various ratios and the resultant static tensile properties of the mixed alloys behave according to rule-of-mixtures. At discontinuous interfaces between Ti-8Al-1Er and commercially-pure titanium, the crack growth behavior progresses smoothly across the discontinuity as the crack transitions from one crack growth regime into another. Studies on monolithic samples shows the mechanisms of damage in the Ti-8Al-1Er; specifically, that strain localization occurs near grain boundaries of high mis-orientation on the microscale and that twinning and dislocation density is concentrated near erbia-strengthening particles (Er2O3) on the nanoscale.

Newman, John A.↗
NASA NTRSDate not supplied

Towards Integrated Computational Materials Engineering for Quantifying Performance Impacts of Microstructure and Defect Interactions in Powder Bed Fusion Parts

Powder bed fusion (PBF) additive manufacturing (AM) enables the creation of parts with complexity and functionality levels that were previously impossible with traditional manufacturing methods. By modifying the laser power, hatch spacing, or the numerous other processing parameters, the PBF process supports the production of a wide set of materials and geometries. However, that same process parameter design flexibility causes the process-design space of PBF to be massive and expensive to explore experimentally. Another challenge is quality variation across a build. As a part is being built, geometric variance between locations, such as at a thin-wall section vs. the bulk material, may cause the specified processing parameters to no longer be acceptable for producing defect-free printing. Furthermore, if the processing parameters deviate during the print process, it is difficult to assess if the part will still perform satisfactorily. Integrated Computational Materials Engineering (ICME) provides a way to understand and address these various challenges. This talk will present advancements in process-structure simulations of PBF at NASA Langley Research Center. The ability to simulate grain-scale PBF microstructures using the Physically Based Monte Carlo method will be demonstrated and compared to experimental measurements. Techniques for simulating three-dimensional lack-of-fusion and keyhole porosity defects based on the specific processing conditions and approaches for integrating the two porosity prediction techniques alongside the computational microstructure evolution models will be shown. Finally, the integration of simulated PBF microstructures, embedded process defects, and crystal plasticity finite element models to elucidate the interaction of porosity and microstructure on micromechanical fields will be demonstrated. These integrated techniques demonstrate an example of using ICME to relate processing to performance for PBF AM materials. With continued maturity, it is hoped that such ICME approaches will lead to next-generation computational-materials supported qualification and certification of AM parts.

Additive manufacturing↗
NASA NTRS1985

Environmental Degradation of Materials: Surface Chemistry Related to Stress Corrosion Cracking

Parallel experiments have been performed in order to develop a comprehensive model for stress cracking (SCC) in structural materials. The central objective is to determine the relationship between the activity and selectivity of the microstructure of structural materials to their dissolution kinetics and experimentally measured SCC kinetics. Zinc was chosen as a prototype metal system. The SCC behavior of two oriented single-crystal disks of zinc in a chromic oxide/sodium sulfate solution (Palmerton solution) were determined. It was found that: (1) the dissolution rate is strongly (hkil)-dependent and proportional to the exposure time in the aggressive environment; and (2) a specific slip system is selectively active to dissolution under applied stress and this slip line controls crack initiation and propagation. As a precursor to potential microgrvity experiments, electrophoretic mobility measurements of zinc particles were obtained in solutions of sodium sulfate (0.0033 M) with concentrations of dissolved oxygen from 2 to 8 ppm. The equilibrium distribution of exposed oriented planes as well as their correlation will determine the particle mobility.

Schwarz, J. A.↗
NASA NTRS1989

Analytical electron microscopy of biogenic and inorganic carbonates

In the terrestrial sedimentary environment, the mineralogically predominant carbonates are calcite-type minerals (rhombohedral carbonates) and aragonite-type minerals (orthorhombic carbonates). Most common minerals precipitating either inorganically or biogenically are high magnesium calcite and aragonite. High magnesium calcite (with magnesium carbonate substituting for more than 7 mole percent of the calcium carbonate) is stable only at temperatures greater than 700 C or thereabouts, and aragonite is stable only at pressures exceeding several kilobars of confining pressure. Therefore, these carbonates are expected to undergo chemical stabilization in the diagenetic environment to ultimately form stable calcite and dolomite. Because of the strong organic control of carbonate deposition in organisms during biomineralization, the microchemistry and microstructure of invertebrate skeletal material is much different than that present in inorganic carbonate cements. The style of preservation of microstructural features in skeletal material is therefore often quite distinctive when compared to that of inorganic carbonate even though wholesale recrystallization of the sediment has taken place. Microstructural and microchemical comparisons are made between high magnesium calcite echinoderm skeletal material and modern inorganic high magnesium calcite inorganic cements, using analytical electron microscopy and related techniques. Similar comparisons are made between analogous materials which have undergone stabilization in the diagenetic environment. Similar analysis schemes may prove useful in distinguishing between biogenic and inorganic carbonates in returned Martian carbonate samples.

Blake, David F.↗
NASA NTRS1979

Evaluation of cellular glasses for solar mirror panel applications

An analytic technique was developed to compare the structural and environmental performance of various materials considered for backing of second surface glass solar mirrors. Cellular glass was determined to be a prime candidate due to its low cost, high stiffness-to-weight ratio, thermal expansion match to mirror glass, evident minimal environmental impact and chemical and dimensional stability under conditions of use. The current state of the art and anticipated developments in cellular glass technology are discussed; material properties are correlated to design requirements. A mathematical model is presented which suggests a design approach which allows minimization of life cost; and, a mechanical and environmental testing program is outlined, designed to provide a material property basis for development of cellular glass hardware, together with methodology for collecting lifetime predictive data. Preliminary material property data from measurements are given. Microstructure of several cellular materials is shown, and sensitivity of cellular glass to freeze-thaw degradation and to slow crack growth is discussed. The effect of surface coating is addressed.

Giovan, M.↗