Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Material Attributes”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8
All sourcesNASA NTRSDOE OSTI
NASA NTRS1987

Millimeter-band oscillations based on resonant tunneling in a double-barrier diode at room temperature

A double-barrier diode at room temperature has yielded oscillations with fundamental frequencies up to 56 GHz and second harmonics up to 87 GHz. The output powers at these frequencies were about 60 and 18 microW, respectively. These results are attributed to a recent improvement in the material parameters of the device and to the integration of the device into a waveguide resonator. The most successful diode to date has thin (about 1.5 nm) AlAs barriers, a 4.5-nm-wide GaAs quantum well, and 2 x 10 to the 17th/cu cm doping concentration in the n-GaAs outside the barriers. This particular diode is expected to oscillate at frequencies higher than those achieved by any reported p-n tunnel diode.

Brown, E. R.↗
NASA NTRS1989

Mid-infrared spectra of WC 9 stars - The composition of circumstellar and interstellar dust

Broad emission features at about 7.7 microns and absorption features at about 6 and 10 microns observed from the WC 9 stars AFGL 2104 and Ve 2-45 are analyzed. The 7.7-micron feature is shown to resemble the well-known PAH band attributed to CC stretching modes in carbonaceous materials. The results suggest a low H abundance in the outflow of these objects, and that, given a strong UV source, all C-rich dust-enshrouded objects will show (some of) the IR emission bands. It is noted that at least 6 percent of the C and 4 percent of the O are locked up in C=O groups in interstellar silicates.

Cohen, M.↗
NASA NTRS1992

The solar wind structures associated with cosmic ray decreases and particle acceleration in 1978-1982

The time histories of particles in the energy range 1 MeV to 1 GeV at times of all greater than 3 percent cosmic ray decreases in the years 1978 to 1982 are studied. Essentially all 59 of the decreases commenced at or before the passages of interplanetary shocks, the majority of which accelerated energetic particles. We use the intensity-time profiles of the energetic particles to separate the cosmic ray decreases into four classes which we subsequently associate with four types of solar wind structures. Decreases in class 1 (15 events) and class 2 (26 events) can be associated with shocks which are driven by energetic coronal mass ejections. For class 1 events the ejecta is detected at 1 AU whereas this is not the case for class 2 events. The shock must therefore play a dominant role in producing the depression of cosmic rays in class 2 events. In all class 1 and 2 events (which comprise 69 percent of the total) the departure time of the ejection from the sun (and hence the location) can be determined from the rapid onset of energetic particles several days before the shock passage at Earth. The class 1 events originate from within 50 deg of central meridian. Class 3 events (10 decreases) can be attributed to less energetic ejections which are directed towards the Earth. In these events the ejecta is more important than the shock in causing a depression in the cosmic ray intensity. The remaining events (14 percent of the total) can be attributed to corotating streams which have ejecta material embedded in them.

Cane, H. V.↗
NASA NTRS1999

Analyses of Contaminated Solar Array Handrail Samples Retrieved from Mir

In January 1998 during, the STS-89 mission, an eight section Russian solar array panel was retrieved after more than ten years exposure to the orbital space environment on the Russian space station Mir. Two darkened handrail samples from the Russian solar array have been evaluated for contamination: a section of a white paint covered rigid handrail and a section of woven fabric over-wrapped around a flexible handhold. The handrail samples were evaluated using optical microscopy (OM), field emission scanning electron microscopy (FESEM) and energy dispersive spectroscopy (EDS). Optical properties were also obtained. Microscopy has shown the discolored areas to have thick layers of contaminant that has crazed and spalled off in regions. Energy dispersive spectroscopy revealed that the brown contaminant is composed of oxidized silicon. No silicon was present on the unexposed fabric over-wrap, and very small amounts were present in the white paint. Therefore, the contaminant layer on both samples is attributed to silicone contamination from other spacecraft materials that have been oxidized by atomic oxygen while in orbit. A significant source of the silicone contamination appears to be from the solar array itself.

deGroh, Kim K.↗
NASA NTRS2007

POSS(Registered TradeMark) Coatings for Solar Cells: An Update

Presently, solar cells are covered with Ce-doped microsheet cover glasses that are attached with Dow Corning DC 93-500 silicone adhesive. Various antireflection coatings are often applied to the cover glass to increase cell performance. This general approach has been used from the beginning of space exploration. However, it is expensive and time consuming. Furthermore, as the voltage of solar arrays increases, significant arcing has occurred in solar arrays, leading to loss of satellite power. The cause has been traced to differential voltages between strings and the close spacing between them with no insulation covering the edges of the solar cells. In addition, this problem could be ameliorated if the cover glass extended over the edges of the cell, but this would impact packing density. An alternative idea that might solve all these issues and be less expensive and more protective is to develop a coating that could be applied over the entire array. Such a coating must be resistant to atomic oxygen for low earth orbits below about 700 km, it must be resistant to ultraviolet radiation for all earth and near-sun orbits and, of course, it must withstand the damaging effects of space radiation. Coating flexibility would be an additional advantage. Based on past experience, one material that has many of the desired attributes of a universal protective coating is the Dow Corning DC 93-500. Of all the potential optical plastics, it appears to be the most suitable for use in space. As noted above, DC 93-500 has been extensively used to attach cover glasses to crystalline solar cells and has worked exceptionally well over the years. It is flexible and generally resistant to electrons, protons and ultraviolet (UV and VUV) radiation; although a VUV-rejection coating or VUV-absorbing ceria-doped cover glass may be required for long mission durations. It can also be applied in a thin coating (< 25 m) by conventional liquid coating processes. Unfortunately, when exposed to atomic oxygen (AO) DC 93-500 develops a frosty surface. Such frosting can lead to a loss of light transmitted into the cells and destroy the essential clarity needed for a concentrator lens.

Brandhorst, Henry↗
NASA NTRS2015

CSI 2264: Characterizing Young Stars in NGC 2264 With Short-Duration Periodic Flux Dips in Their Light Curves

We identify nine young stellar objects (YSOs) in the NGC 2264 star-forming region with optical CoRoT light curves exhibiting short-duration, shallow, periodic flux dips. All of these stars have infrared (IR) excesses that are consistent with their having inner disk walls near the Keplerian corotation radius. The repeating photometric dips have FWHM generally less than one day, depths almost always less than 15%, and periods (3 < P < 11 days) consistent with dust near the Keplerian co-rotation period. The flux dips vary considerably in their depth from epoch to epoch, but usually persist for several weeks and, in two cases, were present in data collected on successive years. For several of these stars, we also measure the photospheric rotation period and find that the rotation and dip periods are the same, as predicted by standard \disk-locking" models. We attribute these flux dips to clumps of material in or near the inner disk wall, passing through our line of sight to the stellar photosphere. In some cases, these dips are also present in simultaneous Spitzer IRAC light curves at 3.6 and 4.5 microns. We characterize the properties of these dips, and compare the stars with light curves exhibiting this behavior to other classes of YSO in NGC 2264. A number of physical mechanisms could locally increase the dust scale height near the inner disk wall, and we discuss several of those mechanisms; the most plausible mechanisms are either a disk warp due to interaction with the stellar magnetic field or dust entrained in funnel- ow accretion columns arising near the inner disk wall.

CSI 2264↗
NASA NTRS1975

Experimental investigation of reaction coronas on olivine in Apollo 14 high-grade breccias

Reaction coronas of pyroxene plus or minus ilmenite occur around clasts of olivine in Apollo 14 high-grade metamorphic breccias. In experiments of several months duration, there was no evidence of corona formation at 1000 C, but at 1050, with oxygen fugacity at or above Ilm-Ru-Fe and below Fe-Fe(1-x)O, incipient coronas formed around Fo(50-70), Fo(68), En(69) + Fe. Reduction of olivine under these conditions is inconsistent with the calculated stability relations and is attributed to uncertainties in the activity coefficient for olivine or pyroxene. The experiments also suggest that vesicularity in the Apollo 14 high-grade breccias may correlate with the amount of glassy material in their unmetamorphosed precursors. The metamorphic event is attributed to burial in a hot ejecta blanket, such as that of the Imbrium event.

Kesson, S. E.↗
NASA NTRS2006

Manned Spacecraft Requirements for Materials and Processes

A major cause of project failure can be attributed to an emphasized focus on end products and inadequate attention to resolving development risks during the initial phases of a project. The initial phases of a project, which we will call the "study period", are critical to determining project scope and costs, and can make or break most projects. If the requirements are not defined adequately, how can the scope be adequately determined, also how can the costs of the entire project be effectively estimated, and how can the risk of project success be accurately assessed? Using the proper material specifications and standards and incorporating these specifications and standards in the design process should be considered inherently crucial to the technical success of a project as just as importantly, crucial to the cost and schedule success. This paper will intertwine several important aspects or considerations for project success: 1) Characteristics of a "Good Material Requirement"; 2) Linking material requirements to the implementation of "Design for Manufacturing"; techniques and 3) The importance of decomposing materials requirements during the study phase/development phase to mitigate project risk for the maturation of technologies before the building of hardware.

Vaughn, Timothy P.↗
NASA NTRS1977

A factory concept for processing and manufacturing with lunar material

A conceptual design for an orbital factory sized to process 1.5 million metric tons per year of raw lunar fines into 0.3 million metric tons of manufacturing materials is presented. A conservative approach involving application of present earth-based technology leads to a design devoid of new inventions. Earth based counterparts to the factory machinery were used to generate subsystem masses and lumped parameters for volume and mass estimates. The results are considered to be conservative since technologies more advanced than those assumed are presently available in many areas. Some attributes of potential space processing technologies applied to material refinement and component manufacture are discussed.

Driggers, G. W.↗
NASA NTRS2008

Mechanical Properties and Durability of "Waterless Concrete"

Waterless concrete consists of molten elementary sulfur and aggregate. The aggregates in lunar environment will be lunar rocks and soil. Sulfur is present on the Moon in Troilite soil (FeS) and by oxidation soil iron and sulfur can be produced. Iron can be used to reinforce the sulfur concrete. Sulfur concrete specimens were cycled between liquid nitrogen (approximately 191 C) and room temperature (approximately 21 C) to simulate exposure to a lunar environment. Cycled and control specimens were subsequently tested in compression at room temperatures (approximately 21 C) and approximately 101 C. Test results showed that due to temperature cycling, compressive strength of cycled specimens was 20% of those non-cycled. Microscopic examination of the fracture surfaces from the cycled samples showed clear de-bonding of the sulfur from the aggregate material whereas it was seen well bonded in those non-cycled. This reduction in strength can be attributed to the large differences in thermal coefficients of expansion of the materials constituting the concrete which promoted cracking. Similar sulfur concrete mixtures were strengthened with short and long glass fibers. The glass fibers from lunar regolith simulant was melted in a 25 cc Pt-Rh crucible in a Sybron Thermoline high temperature MoSi2 furnace at melting temperatures of 1450 to 1600 C for times of 30 min to 1 hour. Glass fibers were cast from the melt into graphite crucibles and were annealed for a couple of hours at 600 C. Glass fibers and small rods were pulled from the melt. The glass melt wets the ceramic rod and long continuous glass fibers were easily hand drawn. The glass fibers were immediately coated with a protective polymer to maintain the mechanical strength. The glass fibers were used to reinforce sulfur concrete plated to improve the flexural strength of the sulfur concrete. Prisms beams strengthened with glass fibers were tested in 4-point bending test. Beams strengthened with glass fiber showed to exhibit an increase in the flexura strength by as much as 45%.

Toutanji, Houssam↗
NASA NTRS1972

Sputtering - A vacuum deposition method for coating material.

The sputtering method is discussed in terms of the unique features which sputter offers in depositing coatings. These features include versatility, momentum transfer, configuration of target, precise controls, and a relatively slow deposition rate. Sputtered films are evaluated in terms of adherence, coherence, and the internal stresses. The observed strong adherence is attributed to the high kinetic energies of the sputtered material, sputter etched surface, and the submicroscopic particle size. Film thickness can be controlled to a millionth of a centimeter. Very adherent films of sputtered PTFE (teflon) can be deposited in a single operation on any type of material and on any geometrical configuration.

Spalvins, T.↗
NASA NTRS2003

Improved Crystal Quality by Detached Solidification in Microgravity

The goals of our work on detached solidification have been to: Develop a complete understanding of all of the phenomena of detached solidification; Make it possible to achieve detached solidification reproducibly; Increase crystallographic perfection through detached solidification. Specifically, we aimed in this project to: Identify a system and develop methods that would allow viewing of the melt surface and convection in the melt during detached solidification in microgravity; Improve understanding of the origination and evolution of detachment through experiments and theoretical treatments; Achieve detachment on earth. The project resulted in 14 publications, 15 presentations, completion of 2 Ph.D. theses, and completion of 2 M.S. theses. Two additional papers are currently being reviewed for publication. Copies of most of the papers are attached as appendices. Among the accomplishments are: Achievement of detached solidification of InSb on earth and determination of the conditions favoring detachment on earth. Development of a new method for coating the interior of silica growth ampoules with transparent boron nitride, which yields the high contact angles for semiconductor melts that favor detachment. Development of a new coating for the interior of Pyrex ampoules yielding very high contact angles for water and molten organic compounds. Development of a material-balance model for steady detached solidification that provides greatly improved insight into the process, both in microgravity and on earth. Dimensionless parameters were found that clarify the role of operating conditions and physical properties. The reason for the occurrence of two steady states was clarified, along with their relative stability. Observation of periodic gas tubes during directional solidification of water and organic compounds. Gas bubbles did not propagate around the periphery to yield full detachment. Failure to obtain detachment is attributed to the ready plastic deformation of these materials, so that the frozen material continues to adhere to the ampoule wall during cooling.

Regel, Liya L.↗
NASA NTRS2010

History of Nebular Processing Traced by Silicate Stardust in IDPS

Chondritic porous interplanetary dust particles (CP-IDPs) may be the best preserved remnants of primordial solar system materials, in part because they were not affected by parent body hydrothermal alteration. Their primitive characteristics include fine grained, unequilibrated, anhydrous mineralogy, enrichment in volatile elements, and abundant molecular cloud material and silicate stardust. However, while the majority of CP-IDP materials likely derived from the Solar System, their formation processes and provenance are poorly constrained. Stardust abundances provide a relative measure of the extent of processing that the Solar System starting materials has undergone in primitive materials. For example, among primitive meteorites silicate stardust abundances vary by over two orders of magnitude (less than 10-200 ppm). This range of abundances is ascribed to varying extents of aqueous processing in the meteorite parent bodies. The higher average silicate stardust abundances among CP-IDPs (greater than 375 ppm) are thus attributable to the lack of aqueous processing of these materials. Yet, silicate stardust abundances in IDPs also vary considerably. While the silicate stardust abundance in IDPs having anomalous N isotopic compositions was reported to be 375 ppm, the abundance in IDPs lacking N anomalies is less than 10 ppm. Furthermore, these values are significantly eclipsed among some IDPs with abundances ranging from 2,000 ppm to 10,000 ppm. Given that CP-IDPs have not been significantly affected by parent body processes, the difference in silicate stardust abundances among these IDPs must reflect varying extents of nebular processing. Here we present recent results of a systematic coordinated mineralogical/isotopic study of large cluster IDPs aimed at (1) characterizing the mineralogy of presolar silicates and (2) delineating the mineralogical and petrographic characteristics of IDPs with differing silicate stardust abundances. One of the goals of this study is to better understand the earliest stages of evolution of the Solar System starting materials.

Messenger, Scott R.↗
NASA NTRS1975

The source and origin of the exotic component and KREEP-rich materials on the moon

The enrichments of trace-element concentrations in lunar soils are attributed to the combined effects of comminution of local rocks and a preferential addition of the exotic component to finer grain sizes. The exotic component appears similar to Fra Mauro materials, and there is a strong correlation between the percentage of exotic component and distance from the Fra Mauro site. Based on trace-element characteristics, it is suggested that the exotic component is finely comminuted KREEP and is dispersed on the lunar surface from the Fra Mauro and other high gamma-ray active regions in the Imbrium-Procellarum regions. The major and trace-element chemistry of these materials is considered to be due to impact melting of trace-element-rich accessory phases followed by variable dilution with partial melts of the bulk solid phases of plagioclase, low-Ca pyroxene, and olivine. The generation of KREEP and the exotic component is an impact-produced local process and need not imply a global occurrence of radioactive crust on the moon.

Murthy, V. R.↗
NASA NTRS1977

Femur-bending properties as influenced by gravity. I - Ultimate load and moment for 3-G rats

Fresh experimental bones can withstand greater bending forces and moments after 1.0 to 2.5 weeks of 3-G exposure. This appears more attributable to a 50% greater strength of bone material than to effects upon size or shape, and is most measurable for animals of 5 to 8 weeks of age. Experimental bone material seems to grow to its mature level at a younger age rather then there being so marked an effect upon the mature level itself. We simulated 3.1 G by chronic centrifugation of 66 albino rats and compared them to 63 1-G controls. Extrapolation of the simplest mathematical description of the present results to weaker, zero-G bones could be tested by a total of 60 space-based control and experimental animals. A flight of only 15 animals would be necessary for comparison to ground-based control animals. This is consistent with reports of bone demineralization during space-flight. In light of the differences in bone histology, however, extrapolation of these results to humans would be premature and, if at all applicable, are most likely to be so for children rather than adults.

Wunder, C. C.↗
NASA NTRS1979

Shock metamorphism of granulated lunar basalt

The paper deals with an extensive series of shock-recovery experiments performed on both nonporous crystalline basalt and its granulated and sieved counterpart to study the role of porosity and grain size in shock motomorphic effects under otherwise identical conditions. Shocked samples are compared with unshocked starting material in terms of textural and mineralogical modifications attributable to shock. A comparative petrographic and chemical characterization is presented of pulverized and sieved lunar basalt 75035 shocked between 6 and 75 GPa in comparison with holocrystalline disks of the same basalts shocked in 10 earlier experiments. Specifically, a petrographic classification of shock features is given, along with an estimation of relative amounts of shock glasses and a chemical characterization of shock glasses in each shocked granular basalt.

Schaal, R. B.↗
NASA NTRS1981

Test progress on the electrostatic membrane reflector

NASA is currently developing a low mass antenna which derives its reflector surface quality from the application of electrostatic forces to form a thin membrane into the desired concave reflector surface. The shuttle-deployed antenna would have a diameter of 100 m and an RMS surface smoothness of 10 to 1 mm for operation at 1 to 10 GHz. Surface quality measurements have been made on a highly deformable elastic membrane, pressurized by electrostatic forces. Included are the effects of the perimeter boundary, splicing of the membrane, the long-scale smoothness of commercial membranes, and the spatial controllability of the membrane using voltage adjustments to alter the electrostatic forces. The electrostatic membrane was found to operate well in an open-loop sense, showing a high degree of position stability and negligible power consumption in dry air. Visco-electric creep was not evident, but the polymer membrane did expand and contract considerably due to its hygroscopic expansion coefficient. A residual roughness of about 0.75 mm existed with the polymer used in these tests; this error is attributed to seams and membrane anisotropy where the material is stiffer in one direction.

Goslee, J. W.↗
NASA NTRS2015

Rheological Properties of Quasi-2D Fluids in Microgravity

In recent years, research on complex fluids and fluids in restricted geometries has attracted much attention in the scientific community. This can be attributed not only to the development of novel materials based on complex fluids but also to a variety of important physical phenomena which have barely been explored. One example is the behavior of membranes and thin fluid films, which can be described by two-dimensional (2D) rheology behavior that is quite different from 3D fluids. In this study, we have investigated the rheological properties of freely suspended films of a thermotropic liquid crystal in microgravity experiments. This model system mimics isotropic and anisotropic quasi 2D fluids [46]. We use inkjet printing technology to dispense small droplets (inclusions) onto the film surface. The motion of these inclusions provides information on the rheological properties of the films and allows the study of a variety of flow instabilities. Flat films have been investigated on a sub-orbital rocket flight and curved films (bubbles) have been studied in the ISS project OASIS. Microgravity is essential when the films are curved in order to avoid sedimentation. The experiments yield the mobility of the droplets in the films as well as the mutual mobility of pairs of particles. Experimental results will be presented for 2D-isotropic (smectic-A) and 2D-nematic (smectic-C) phases.

microgravity↗