Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “MAGNETRONS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8

Subcritical-voltage magnetron RF power source

A system and method of operating a magnetron power source can achieve a broad range of output power control by operating a magnetron with its cathode voltage lower than that needed for free running oscillations (e.g., below the Kapitsa critical voltage or equivalently below the Hartree voltage) A sufficiently strong injection-locking signal enables the output power to be coherently generated and to be controlled over a broad power range by small changes in the cathode voltage. In one embodiment, the present system and method is used for a practical, single, frequency-locked 2-magnetron system design.

Kazakevich, Grigory M.↗

Subcritical-voltage magnetron RF power source

A system and method of operating a magnetron power source can achieve a broad range of output power control by operating a magnetron with its cathode voltage lower than that needed for free running oscillations (e.g., below the Kapitsa critical voltage or equivalently below the Hartree voltage) A sufficiently strong injection-locking signal enables the output power to be coherently generated and to be controlled over a broad power range by small changes in the cathode voltage. In one embodiment, the present system and method is used for a practical, single, frequency-locked 2-magnetron system design.

30 DIRECT ENERGY CONVERSION↗

Properties of Molybdenum Films Produced by High-Power Impulse Magnetron Sputtering

Results of experiments on deposition of thin molybdenum films on glass substrates by high-power impulse magnetron sputtering are presented. Two high-current modes with different pulse frequencies and durations are used. Properties of the produced molybdenum films are compared with those of films produced by magnetron sputtering at a direct current. It is shown that this method allows the resistivity of molybdenum films to be decreased and their reflectance in the visible range to be increased.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Thermodynamic Investigation of the Effect of Target Compositions and Conditions of Their Magnetron Sputtering on Phase Compositions of the Resulting Films

A thermodynamic investigation of plasmochemical processes taking place in a magnetron during sputtering of the targets consisting of indium and dysprosium ions is performed, which allowed identifying the feasibility of forming under the given conditions certain amounts of the chemical compounds In{sub 2}O{sub 3}, Dy{sub 2}O{sub 3}, DyInO{sub 3}. In the thermodynamic analysis of the equilibrium compositions during magnetron sputtering of the films, a universal TERRA software program is used.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Investigation of Corrosion Behavior of Ti/TiN Multilayers on Al7075 Deposited by High-Vacuum Magnetron Sputtering in 3.5% NaCl Solution

Although Al 7075 has many favorable mechanical properties such as the large strength-to-weight ratio, the relatively poor corrosion resistance has restricted industrial applications. In this work, Ti/TiN as hard multilayered and nanostructured coatings are deposited on the relatively soft Al 7075 structure by high-vacuum radio-frequency magnetron sputtering and the phase, structure, and morphology are investigated in details. The corrosion behavior is evaluated by electrochemical impedance spectroscopy in 3.5% NaCl at a pH of 7.5 for 1, 6, 12, 24, 36, 48, 60, and 72 h. At time points of 1, 6, 12, and 24 h, primary oxide layers and double layers are formed, but the corrosive medium penetrates the primary titanium nitride columnar structure. At longer time points of 24, 36, 48, 60, and 72 h, formation of stronger oxide and double layers leads to better corrosion resistance which is 14.8 times better than that observed from the uncoated substrate after immersion for 36 h. According to R{sub ct}, the corrosion resistances of the short and long immersion groups are 808.5-1984 and 808.5-1248 kΩ cm{sup 2}, respectively, thereby confirming the effectiveness of the Ti/TiN coating against corrosion in comparison with the corrosion resistance of 84.3 kΩ cm{sup 2} observed from the uncoated Al 7075. The smallest corrosion resistance of 808.5 kΩ cm{sup 2} observed at the time point of 24 h is 9.6 times that of the uncoated substrate. Graphical Abstract: A 1.4-µm-thick Ti/TiN hard nanostructured coating comprising six layers is deposited on the relatively soft Al 7075 substrate by high-vacuum radio-frequency magnetron sputtering at 100 °C. The first layer of the intermediate Ti layer cannot improve the corrosion resistance of the TiN super hard coating with a columnar structure. The second and third intermediate Ti layers play an important role in improving the corrosion resistance of Al 7075 by obstructing defects and coating damage from aggressive Cl{sup −} ions and penetration of water. The mechanism involves self-healing of defects by oxide formation and Warburg resistance by diffusion control. .

36 MATERIALS SCIENCE↗

Effects of sample bias on adhesion of magnetron sputtered Cr coatings on SiC

Swelling of SiC at 300 C due to in-service neutron irradiation causes tensile residual stresses in coatings which are expected to adversely affect the performance of coated SiC composite fuel cladding for light water reactors. Matching the coating swelling with the substrate, a solution common for thermal expansion, is not practical in the case of neutron irradiation. Biasing samples during magnetron sputtering deposition induces compressive residual stress which may counteract this. In this study, chromium coatings were deposited on SiC by DC magnetron sputtering with no external heating at bias voltages of –50V, –75V, and –100V. The effects of the bias voltage on morphology, residual stress, microstrain, texture, and adhesion are shown. The low deposition temperature resulted in the coating microstructure evolution following an energetic particle bombardment dominated trend. Additionally, at the two lower bias voltages knock-on implantation dominated increasing the residual stress and microstrain while at the highest bias voltage, thermal spike migration allowed for defect relaxation. When the knock-on induced compressive residual stress exceeded 0.8 GPa microcrack formation in the SiC substrate decreased coating adhesion. While no microcracks formed at the lowest bias voltage, insufficient atomic mobility during coating growth lead to voids forming in the coating. A balance is needed to form void-free coatings that have high compressive residual stress.

36 MATERIALS SCIENCE↗

Effects of substrate temperature on properties of ITO-ZnO composition spread films fabricated by combinatorial RF magnetron sputtering

We have fabricated ITO-ZnO composition spread films to investigate the effects of substrate temperature on their electrical and optical properties by using combinatorial RF magnetron sputtering. It turned out by X-ray measurement that the film with zinc contents above 16.0 at% [Zn/(In+Zn+Sn)] showed amorphous phase regardless of substrate temperature. The amorphous ITO-ZnO film had lower resistivity than polycrystalline films. When the films were deposited at 250 deg. C, the minimum resistivity of 3.0x10{sup -4} OMEGA cm was obtained with the zinc contents of 16.0 at%. The indium content could be reduced as high as {approx}30 at% compared to that of ITO for the films having similar resistivity ({approx}10{sup -4} OMEGA cm). However, a drastic increase of resistivity was observed for the ITO-ZnO films deposited at 350 deg. C, having zinc contents below 15.2 at%. - Graphical abstract: The effects of substrate temperature on properties of ITO-ZnO films were investigated by using combinatorial RF magnetron sputtering. The amorphous ITO-ZnO film had lower resistivity than polycrystalline films. The minimum resistivity of 3.0x10{sup -4} OMEGA cm was obtained with the substrate temperature of 250 deg. C and the zinc contents of 16.0 at%. The electronic states of ITO-ZnO films were discussed with related to the formation of transparent amorphous oxide semiconductor (TAOS).

36 MATERIALS SCIENCE↗

Structural and optical characterization of high-quality ZnO thin films deposited by reactive RF magnetron sputtering

Highlights: ► High-quality ZnO thin films were deposited at room temperature. ► Effect of O{sub 2} flow and RF sputtering voltages on properties of ZnO films were studied. ► O{sub 2}/Ar ratios played a key role in controlling optical properties of ZnO films. ► Photoluminescence intensity of the ZnO films strongly depended on O{sub 2}/Ar ratios. ► Crystallite size, stress and strain strongly depended on O{sub 2}/Ar ratios. - Abstract: ZnO thin films were deposited onto quartz substrates by radio frequency (RF) reactive magnetron sputtering using a Zn target. The structural and optical properties of the ZnO thin films were investigated comprehensively by X-ray diffraction (XRD), ultraviolet–visible and photoluminescence (PL) measurements. The effects of the oxygen content of the total oxygen–argon mixture and sputtering voltage in the sputtering process on the structural and optical properties of the ZnO films were studied systemically. The microstructural parameters, such as the lattice constant, crystallite size, stress and strain, were also calculated and correlated with the structural and optical properties of the ZnO films. In addition, the results showed that the crystalline quality of ZnO thin films improved with increasing O{sub 2}/Ar gas flow ratio from 2:8 to 8:2. XRD and PL spectroscopy revealed 800 V to be the most appropriate sputtering voltage for ZnO thin film growth. High-quality ZnO films with a good crystalline structure, tunable optical band gap as well as high transmittance could be fabricated easily by RF reactive magnetron sputtering, paving the way to obtaining cost-effective ZnO thin films transparent conducting oxides for optoelectronics applications.

36 MATERIALS SCIENCE↗

Microstructural, optical, and electrical properties of Ni–Al co-doped ZnO films prepared by DC magnetron sputtering

Graphical abstract: - Highlights: • Ni–Al co-doped ZnO (NiAl:ZnO) composite thin films were deposited by DC magnetron sputtering at room temperature. • All films showed a highly preferential (0 0 2) c-axis orientation. • XPS revealed the presence of metallic Ni, NiO, and Ni{sub 2}O{sub 3} states, and Ni atoms were successfully doped in the NiAl:ZnO films. • NiAl:ZnO (3 wt% Ni) film showed the lowest electrical resistivity of 2.59 × 10{sup −3} Ω cm. • Band gap widening (4.18 eV) was observed in the NiAl:ZnO films with 5 wt% Ni. - Abstract: Ni–Al co-doped ZnO (NiAl:ZnO) films with fixed Al content at 2 wt% and different Ni contents (2.5, 3, and 5 wt%) were deposited by DC magnetron sputtering in an argon atmosphere at room temperature. X-ray diffraction revealed that all films showed a highly preferential (0 0 2) c-axis orientation. XPS revealed the presence of metallic Ni, NiO, and Ni{sub 2}O{sub 3} states, and Ni atoms were successfully doped in NiAl:ZnO films, which did not result in a change in ZnO crystal structure and orientation. The electrical resistivity of NiAl:ZnO film was decreased to 2.59 × 10{sup −3} Ω cm at a Ni doping concentration of 3 wt% compared with undoped Al-doped ZnO film (5.58 × 10{sup −3} Ω cm). The mean optical transmittance in the visible range was greater than 80% for all films. Band gap widening (4.18 eV) was observed in the NiAl:ZnO films with 5 wt% Ni, attributed to the Burstein–Moss shift due to the increase of carrier concentration.

36 MATERIALS SCIENCE↗

Electrochemical and microstructural characterization of magnetron-sputtered ATO thin films as Li–ion storage materials

Highlights: • Nano-structured ATO thin films prepared by RF magnetron sputtering at 25 °C, 100 °C and 200 °C, respectively. • ATO thin films show a high reversible capacity and high rate performance. • Electrochemical reaction mechanism of the ATO thin film was revealed by transmission electron microscopy. - Abstract: Sb-doped SnO{sub 2} (ATO) nanostructured thin films were prepared by using radio frequency magnetron sputtering at the substrate temperatures of 25 °C, 100 °C and 200 °C, respectively. All the ATO thin films have the similar redox characteristics in the cyclic voltammetry measurements. The ATO thin film sputtered at 200 °C shows the lowest charge transfer resistance and best electrochemical performance, and has a high reversible capacity of 679 mA h g{sup −1} at 100 mA g{sup −1} after 200 charge–discharge cycles and high rate performance of 483 mA h g{sup −1} at 800 mA g{sup −1}. The electrochemical mechanisms were investigated by analyzing the phase evolution of the ATO electrodes that had been electrochemically induced at various stages. The results reveal that the ATO underwent reversible lithiation/delithiation processes during the electrochemical cycles, i.e., the SnO{sub 2} reacted with Li{sup +} to produce metallic Sn and followed by the formation of the Li{sub x}Sn alloys during discharge process, and then Li{sub x}Sn alloys de-alloyed, Sn reacted with Li{sub 2}O, and even partially formed SnO{sub 2} during charge process.

36 MATERIALS SCIENCE↗

High energy-storage performance of 0.9Pb(Mg{sub 1/3}Nb{sub 2/3})O{sub 3}-0.1PbTiO{sub 3} relaxor ferroelectric thin films prepared by RF magnetron sputtering

Highlights: • High-quality PMN-PT 90/10 RFE thin films were prepared by RF magnetron sputtering. • The maximum discharged density of 31.3 J/cm{sup 3} was obtained in the 750-nm-thick film. • PMN-PT RFE films might be a promising material for energy-storage application. - Abstract: 0.9Pb(Mg{sub 1/3}Nb{sub 2/3})O{sub 3}-0.1PbTiO{sub 3} (PMN-PT 90/10) relaxor ferroelectric thin films with different thicknesses were deposited on the LaNiO{sub 3}/Si (100) by the radio-frequency (RF) magnetron sputtering technique. The effects of thickness and deposition temperature on the microstructure, dielectric properties and the energy-storage performance of the thin films were investigated in detail. X-ray diffraction spectra indicated that the thin films had crystallized into a pure perovskite phase with a (100)-preferred orientation after annealed at 700 °C. Moreover, all the PMN-PT 90/10 thin films showed the uniform and crack-free surface microstructure. As a result, a larger recoverable energy density of 31.3 J/cm{sup 3} was achieved in the 750-nm-thick film under 2640 kV/cm at room temperature. Thus, PMN-PT 90/10 relaxor thin films are the promising candidate for energy-storage capacitor application.

36 MATERIALS SCIENCE↗

Electrical and optical properties of nitrogen doped SnO{sub 2} thin films deposited on flexible substrates by magnetron sputtering

Graphical abstract: The best SnO{sub 2}:N TCO film: about 80% transmittance and 9.1 × 10{sup −4} Ω cm. - Highlights: • Nitrogen-doped tin oxide film was deposited on PET by RF-magnetron sputtering. • Effects of oxygen partial pressure on the properties of thin films were investigated. • For SnO{sub 2}:N film, visible light transmittance was 80% and electrical resistivity was 9.1 × 10{sup −4} Ω cm. - Abstract: Nitrogen-doped tin oxide (SnO{sub 2}:N) thin films were deposited on flexible polyethylene terephthalate (PET) substrates at room temperature by RF-magnetron sputtering. Effects of oxygen partial pressure (0–4%) on electrical and optical properties of thin films were investigated. Experimental results showed that SnO{sub 2}:N films were amorphous state, and O/Sn ratios of SnO{sub 2}:N films were deviated from the standard stoichiometry 2:1. Optical band gap of SnO{sub 2}:N films increased from approximately 3.10 eV to 3.42 eV as oxygen partial pressure increased from 0% to 4%. For SnO{sub 2}:N thin films deposited on PET, transmittance was about 80% in the visible light region. The best transparent conductive oxide (TCO) deposited on flexible PET substrates was SnO{sub 2}:N thin films preparing at 2% oxygen partial pressure, the transmittance was about 80% and electrical conductivity was about 9.1 × 10{sup −4} Ω cm.

36 MATERIALS SCIENCE↗

Effect of Ar ion-beam-assistance and substrate temperature on physical properties of Al-doped ZnO thin films deposited by RF magnetron sputtering

Highlights: • AZO and IAZO (303–473 K) films were grown by RF magnetron sputtering technique. • Ar ion-beam converts its kinetic energy as diffusion energy to the deposited atoms. • Structural evolution relies on diffusion energy imparted to the deposited atoms. • Surface texture densify under the aid of ion-beam and substrate temperature. - Abstract: In this study, pronounced effects of ion-beam-assistance and substrate temperature were revealed by exploring the physical properties of Al-doped ZnO thin films deposited by the RF magnetron sputtering technique. Herein, two measurable parameters, ion-beam discharge current (0.1 A) and substrate temperature (303–473 K) were adopted to regulate the structural changes in Al-doped ZnO films. Specifically, progressive structural changes were achieved based on the addition of Ar ion-beam during the film growth. From XRD analysis, we observed significant structural changes that provided an improvement in the film growth towards c-axis (002) plane. In addition, FESEM and AFM analyses demonstrated excellent surface features with the assisted Ar ion-beam. As a result of this process, we effectively modulated the binding energy of Zn 2p level. Finally, the structural investigation accurately demonstrated that the dependence of assisted ion-beam and substrate temperature linearly related to the superior visible transmittance and reduced band gap.

36 MATERIALS SCIENCE↗

A review comparing cathodic arcs and high power impulse magnetron sputtering (HiPIMS)

In this study, high power impulse magnetron sputtering (HiPIMS) has been in the center of attention over the last years as it is an emerging physical vapor deposition (PVD) technology that combines advantages of magnetron sputtering with various forms of energetic deposition of films such as ion plating and cathodic arc plasma deposition. It should not come at a surprise that many extension and variations of HiPIMS make use, intentionally or unintentionally, of previously discovered approaches to film processing such as substrate surface preparation by metal ion sputtering and phased biasing for film texture and stress control. Therefore, in this review, an overview is given on some historical developments and features of cathodic arc and HiPIMS plasmas, showing commonalities and differences. To limit the scope, emphasis is put on plasma properties, as opposed to surveying the vast literature on specific film materials and their properties.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Influence of oxygen on the optical and electrical properties of magnetron-sputtered indium tin oxide thin films at ambient temperature

Indium Tin Oxide (ITO) thin films are commonly used as transparent conductive layers in the production of solar cells. ITO films are typically heat-treated at temperatures exceeding 200 °C after magnetron sputtering to optimize the physical, optical, and electrical characteristics for photovoltaic devices. Here, this high temperature heating procedure greatly limits the use of potential substrates, particularly those comprised of low-temperature-rated polymers. Herein, we examine the physical, optical, and electrical transport effects of oxygen:argon plasmas during radio frequency magnetron sputtering of ITO on glass and flexible polymer surfaces without subsequent heat treatment. ITO thin films were characterized via sheet resistance testing, UV-Vis spectroscopy, X-ray diffraction, and scanning electron microscopy imaging. Sheet resistance measurements revealed an increase in surface resistance with increasing oxygen concentration during sputtering. UV-Vis optical transmittance measurements demonstrated an improvement in optical transmittance with an increase in oxygen concentration reaching a maximum transmittance at an oxygen concentration of 1-2 %. Most importantly, it was discovered that producing bilayers of ITO with pure argon sputtered plasmas followed by oxygen:argon plasmas produced ITO thin films with suitable resistance and transmittance without the need for high temperature post annealing. These results highlight a methodology for the deposition of ITO thin films on temperature sensitive substrates for flexible photovoltaics and low-cost module production.

36 MATERIALS SCIENCE↗

Effects of frequency chirp on magnetron injection locking

The injection locking of a magnetron is theoretically analyzed when either the free running oscillator or the drive signal has a frequency chirp. It is found that complete phase locking of the signal cannot be achieved in either case. However, as long as the locking condition of Adler is well-satisfied instantaneously, a high degree of locking occurs during a major duration of the frequency chirps. The expected output phase variation is computed in terms of the noise in the free-running magnetron oscillator for the case of constant drive frequency.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Ion composition produced by high power impulse magnetron sputtering discharges near the substrate

Plasma composition near the substrate was investigated in a high power impulse magnetron sputtering (HIPIMS) discharge using Langmuir probe analysis, mass spectroscopy, and atomic absorption spectroscopy. The HIPIMS discharge was operated in nonreactive Ar atmosphere at a pressure of 2.66 Pa and the magnetron cathode was furnished with Ti target. Plasma density, metal ion-to-neutral ratio, and gas ion-to-metal ion ratio were studied as a function of discharge current. At peak discharge current densities of {approx}1 A cm{sup -2}, the results show that a dense plasma (n{sub e}{approx}10{sup 18} m{sup -3}) expanded from the target toward the substrate and lasted more than 330 {mu}s after the supplied power was turned off. The shape of the time-averaged ion energy distribution function of sputtered material exhibited a transition from Thompson to Maxwellian distribution, indicating efficient energy transfer in the discharge. The metal content in the plasma monotonically increased with discharge current and the metal ion-to-neutral ratio reached approximately 1:1 in the postdischarge plasma at peak current density of 5 A cm{sup -2}.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

The HERA Magnetron: 24 Years Of Experience, A World Record Run And A New Design

The HERA magnetron is based on a design from FNAL. This technology was developed at the INP in the 70 s, transferred to BNL and from there to FNAL. The DESY magnetron was modified according to the requirements of the HERA collider. During the first years it was the only source connected to the H{sup -} LINAC. It was necessary to run the source for long uninterrupted periods with a high reliability and fortunately with a low duty cycle. Many improvements in the design were made, including the development of a vacuum module which could be changed in minutes, the addition of internal cathode heating, and cathode grooving. To study the influence of the cathode temperature a set-up with air temperature stabilization of the cathode was developed. The cesium consumption could be significantly reduced. The source has now been running without cleaning for more than two and a half years after a fine tuning of all parameters.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗