Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “MAGNETRON SPUTTERING”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8

Low-temperature growth of gallium nitride films by inductively coupled-plasma-enhanced reactive magnetron sputtering

Gallium nitride (GaN) films were grown on sapphire substrate by reactive magnetron sputtering. Inductively coupled-plasma (ICP) source was installed between the substrate holder and the sputtering target to increase the plasma density and the degree of ionization of nitrogen gas. Liquid Ga and Ar/N{sub 2} were used as the sputtering target and sputtering gases, respectively. X-ray diffraction measurements confirmed that the authors could grow high quality GaN crystallites at 500 °C. However, the crystalline GaN (0002) peak remained even by lowering the growth temperature down to 300 °C. The N:Ga ratio of the film grown at 500 °C was almost 1:1, and the nitrogen composition became higher toward the 1:1 N:Ga ratio with increasing the growth temperature. The high degree of ionization induced by ICP source was essential to the growth of high crystalline quality GaN films.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Silicon oxynitride films deposited by reactive high power impulse magnetron sputtering using nitrous oxide as a single-source precursor

Silicon oxynitride thin films were synthesized by reactive high power impulse magnetron sputtering of silicon in argon/nitrous oxide plasmas. Nitrous oxide was employed as a single-source precursor supplying oxygen and nitrogen for the film growth. The films were characterized by elastic recoil detection analysis, x-ray photoelectron spectroscopy, x-ray diffraction, x-ray reflectivity, scanning electron microscopy, and spectroscopic ellipsometry. Results show that the films are silicon rich, amorphous, and exhibit a random chemical bonding structure. The optical properties with the refractive index and the extinction coefficient correlate with the film elemental composition, showing decreasing values with increasing film oxygen and nitrogen content. The total percentage of oxygen and nitrogen in the films is controlled by adjusting the gas flow ratio in the deposition processes. Furthermore, it is shown that the film oxygen-to-nitrogen ratio can be tailored by the high power impulse magnetron sputtering-specific parameters pulse frequency and energy per pulse.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Post-growth annealing induced change of conductivity in As-doped ZnO grown by radio frequency magnetron sputtering

Arsenic-doped ZnO films were fabricated by radio frequency magnetron sputtering method at a relatively low substrate temperature of 200 deg. C. Post-growth annealing in air was carried out up to a temperature of 1000 deg. C. The samples were characterized by Hall measurement, positron annihilation spectroscopy (PAS), secondary ion mass spectroscopy (SIMS), and cathodoluminescence (CL). The as-grown sample was of n-type and it converted to p-type material after the 400 deg. C annealing. The resulting hole concentration was found to increase with annealing temperature and reached a maximum of 6 x 10{sup 17} cm{sup -3} at the annealing temperature of 600 deg. C. The origin of the p-type conductivity was consistent with the As{sub Zn}(V{sub Zn}){sub 2} shallow acceptor model. Further increasing the annealing temperature would decrease the hole concentration of the samples finally converted the sample back to n-type. With evidence, it was suggested that the removal of the p-type conductivity was due to the dissociation of the As{sub Zn}(V{sub Zn}){sub 2} acceptor and the creation of the deep level defect giving rise to the green luminescence.

36 MATERIALS SCIENCE↗

On the pressure effect in energetic deposition of Cu thin films by modulated pulsed power magnetron sputtering: A global plasma model and experiments

The modulated pulsed power magnetron sputtering (MPPMS) discharge processes are numerically modeled and experimentally investigated, in order to explore the effect of the pressure on MPPMS discharges as well as on the microstructure of the deposited thin films. A global plasma model has been developed based on a volume-averaged global description of the ionization region, considering the loss of electrons by cross-B diffusion. The temporal variations of internal plasma parameters at different pressures from 0.1 to 0.7 Pa are obtained by fitting the model to duplicate the experimental discharge data, and Cu thin films are deposited by MPPMS at the corresponding pressures. The surface morphology, grain size and orientation, and microstructure of the deposited thin films are investigated by scanning electron microscopy, transmission electron microscopy, and x-ray diffraction. By increasing the pressure from 0.1 to 0.7 Pa, both the ion bombardment energy and substrate temperature which are estimated by the modeled plasma parameters decrease, corresponding to the observed transition of the deposited thin films from a void free structure with a wide distribution of grain size (zone T) into an underdense structure with a fine fiber texture (zone 1) in the extended structure zone diagram (SZD). The microstructure and texture transition of Cu thin films are well-explained by the extended SZD, suggesting that the primary plasma processes are properly incorporated in the model. The results contribute to the understanding of the characteristics of MPPMS discharges, as well as its correlation with the microstructure and texture of deposited Cu thin films.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Optical properties of nanocrystalline WO{sub 3} and WO{sub 3-x} thin films prepared by DC magnetron sputtering

The optical properties of tungsten trioxide thin films prepared by DC magnetron sputtering, with different oxygen vacancy (V{sub o}) concentration, have been studied by spectrophotometry and photoluminescence (PL) emission spectroscopy. Absorption and PL spectra show that the films exhibit similar band gap energies, E{sub g} ≈ 2.9 eV. The absorption spectra of the films show two pronounced absorption bands in the near-infrared region. One peak (P1) is located at approximately 0.7 eV, independent of V{sub o} concentration. A second peak (P2) shifts from 0.96 eV to 1.16 eV with decreasing V{sub o} concentration. Peak P1 is assigned to polaron absorption due to transitions between tungsten sites (W{sup 5+} → W{sup 6+}), or an optical transition from a neutral vacancy state to the conduction band, V{sub o}{sup 0} → W{sup 6+}. The origin of peak P2 is more uncertain but may involve +1 and +2 charged vacancy sites. The PL spectra show several emission bands in the range 2.07 to 3.10 eV in the more sub-stoichiometric and 2.40 to 3.02 eV in the less sub-stoichiometric films. The low energy emission bands agree well with calculated optical transition energies of oxygen vacancy sites, with dominant contribution from neutral and singly charged vacancies in the less sub-stoichiometric films, and additional contributions from doubly charged vacancy sites in the more sub-stoichiometric films.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Compositional study of vacuum annealed Al doped ZnO thin films obtained by RF magnetron sputtering

Aluminum doped zinc oxide (AZO) thin films were obtained by RF magnetron sputtering. The effects of deposition parameters such as power, gas flow conditions, and substrate heating have been studied. Deposited and annealed films were characterized for composition as well as microstructure using x ray photoelectron spectroscopy and x ray diffraction. Films produced were polycrystalline in nature. Surface imaging and roughness studies were carried out using SEM and AFM, respectively. Columnar grain growth was predominantly observed. Optical and electrical properties were evaluated for transparent conducting oxide applications. Processing conditions were optimized to obtain highly transparent AZO films with a low resistivity value of 6.67 x 10{sup -4}{Omega} cm.

36 MATERIALS SCIENCE↗

Plasma potential mapping of high power impulse magnetron sputtering discharges

Pulsed emissive probe techniques have been used to determine the plasma potential distribution of high power impulse magnetron sputtering (HiPIMS) discharges. An unbalanced magnetron with a niobium target in argon was investigated for a pulse length of 100 {mu}s at a pulse repetition rate of 100 Hz, giving a peak current of 170 A. The probe data were recorded with a time resolution of 20 ns and a spatial resolution of 1 mm. It is shown that the local plasma potential varies greatly in space and time. The lowest potential was found over the target's racetrack, gradually reaching anode potential (ground) several centimeters away from the target. The magnetic presheath exhibits a funnel-shaped plasma potential resulting in an electric field which accelerates ions toward the racetrack. In certain regions and times, the potential exhibits weak local maxima which allow for ion acceleration to the substrate. Knowledge of the local E and static B fields lets us derive the electrons'ExB drift velocity, which is about 10{sup 5} m/s and shows structures in space and time.

36 MATERIALS SCIENCE↗

Boron carbide films with reduced nodular defect density deposited by full-face erosion radio-frequency magnetron sputtering

Boron carbide coatings deposited by sputtering with conventional planar magnetrons exhibit nodular growth defects. Here, we demonstrate that the density of nodular defects in B 4 C films can be greatly reduced by using a full-face-erosion magnetron source that achieves a more uniform target erosion by sweeping the confining magnetic field over the target surface. Here, we systematically study properties of B 4 C films deposited on substrates with different tilt angles and demonstrate deposition of ultrathick films with compressive residual stress below 200MPa.

36 MATERIALS SCIENCE↗

Growth and characterization of TiAlN/CrAlN superlattices prepared by reactive direct current magnetron sputtering

TiAlN and CrAlN coatings were prepared using a reactive direct current magnetron sputtering system from TiAl and CrAl targets. Structural characterization of the coatings using x-ray diffraction (XRD) revealed the B1 NaCl structure of TiAlN and CrAlN coatings with a prominent reflection along the (111) plane. The XPS data confirmed the bonding structures of TiAlN and CrAlN single layer coatings. Subsequently, nanolayered multilayer coatings of TiAlN/CrAlN were deposited on silicon and mild steel (MS) substrates at different modulation wavelengths ({lambda}) with a total thickness of approximately 1.0 {mu}m. The modulation wavelengths were calculated from the x-ray reflectivity data using modified Bragg's law. TiAlN/CrAlN multilayer coatings were textured along (111) for {lambda}<200 A and the XRD patterns showed the formation of superlattice structure for coatings deposited at {lambda}=102 A. The x-ray reflectivity data showed reflections of fifth and seventh orders for multilayer coatings deposited at {lambda}=102 and 138 A, respectively, indicating the formation of sharp interfaces between TiAlN and CrAlN layers. The cross-sectional scanning electron microscopy image of TiAlN/CrAlN multilayer coatings indicated a noncolumnar and dense microstructure. A maximum hardness of 39 GPa was observed for TiAlN/CrAlN multilayer coatings deposited at {lambda}=93 A, which was higher than the rule-of-mixture value (30 GPa) for TiAlN and CrAlN. Study of thermal stability of the coatings in air using micro-Raman spectroscopy indicated that the TiAlN/CrAlN multilayer coatings were stable up to 900 deg. C in air. TiAlN/CrAlN multilayer coatings also exhibited improved corrosion resistance when compared to the MS substrate.

36 MATERIALS SCIENCE↗

Spatial resistivity distribution of transparent conducting impurity-doped ZnO thin films deposited on substrates by dc magnetron sputtering

In transparent conducting impurity-doped ZnO thin films prepared by a conventional dc magnetron sputtering deposition (dc-MSD), the key factors in the deposition conditions that are necessary for practical use in transparent electrode applications were investigated. It was found that impurity-doped ZnO targets with a resistivity higher than approximately 3 m{Omega} cm are unsuitable for practical use in the preparation of transparent conducting Al-doped ZnO and Ga-doped ZnO thin films by conventional dc-MSD. Improvements of both the resulting resistivity distribution and resistivity can be sufficiently obtained only by using targets with a resistivity lower than about 0.5 m{Omega} cm. Using a low oxygen content target having a lower resistivity was found to reduce both the amount of oxygen in the chamber and the amount of oxygen reaching the substrate surface. As a result, it was demonstrated that sintered impurity-doped ZnO targets optimized for the preparation of thin films with lower resistivity as well as more uniform resistivity distribution on the substrate surface tended to exhibit a resistivity lower than about 0.5 m{Omega} cm.

36 MATERIALS SCIENCE↗

Nitrogen self-diffusion in magnetron sputtered Si-C-N films

Self-diffusion was studied in magnetron sputtered nitrogen-rich amorphous compounds of the system Si-C-N by using nitrogen as a model tracer. As shown by infra-red spectroscopy a transient metastable region exists, where the structure of the material can be visualized as silicon nitride tetrahedra which are connected by carbo-diimide (-N=C=N-) bonds to a three dimensional amorphous network. In this region diffusion studies are carried out by neutron reflectometry and isotope multilayers as a function of annealing time, temperature and chemical composition. Low diffusivities between 10{sup -20} and 10{sup -24} m{sup 2}/s were found. In the metastable region, diffusion is faster than diffusion in amorphous silicon nitride by 1 to 2 orders of magnitude, while the activation enthalpies of diffusion between 3.1 and 3.4 eV are the same within error limits. This can be explained by the fact that the diffusion mechanism along SiN{sub 4} tetrahedra is identical to that in amorphous silicon nitride, however, the carbo-diimide bonds seem to widen the structure, allowing faster diffusion. A correlation between diffusivities and the number of carbo-diimid bonds present in the material is found, where the highest diffusivities are observed for materials with the highest number of carbo-diimid bonds, close to the composition Si{sub 2}CN{sub 4}.

36 MATERIALS SCIENCE↗

Synthesis of Highly Oriented Zinc-Oxide Films on Amorphous Substrates by the Method of Direct-Current Magnetron Sputtering

We describe the technology of obtaining highly oriented zinc-oxide (ZnO) films on amorphous substrates at high growth rates (up to 7 nm/s) by means of direct-current magnetron sputtering. It is suggested to optimize the substrate position with respect to magnetron and consider the floating potential to which the substrate is charged in magnetron discharge plasma as one of the main technological parameters. Electrondiffraction study of the structural characteristics of the obtained ZnO films showed that increase in the substrate temperature was accompanied by transformation of the crystallite shape from platelike to columnar.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Probing layered structure of Inconel 625 coatings prepared by magnetron sputtering

Coating/substrate interface and oxide layers present in Inconel 625 film may cause significant impacts on its corrosion behavior. However, layered structure of Inconel 625 coatings remains poorly understood due to its requirement of high spatial resolution. Here we have applied X-ray reflectometry (XRR) to probe the layered structure of magnetron-sputtered Inconel 625 film with atomic spatial resolution. Our results indicate that there exists a 2 nm thick Cr-rich Inconel sublayer underneath the principal film. On top of the principal film, it is found a 2 nm thick oxide layer mainly consisting of NiO. In addition, we detected ~2 Å contamination layer on the sapphire substrate, although argon ion sputter cleaning had been applied to the substrate prior to deposition. By comparing the coatings with different deposition time, we observed that the thickness of principal Inconel 625 layer grows linearly with deposition time, with all other layers remaining constant. Our findings provide insight into the layered structures of Inconel 625 coatings with atomic-scale spatial resolution, and provide directions for future efforts that aim to improve the corrosion resistance of Inconel 625 coatings.

14 SOLAR ENERGY↗

Control of ions energy distribution in dual-frequency magnetron sputtering discharges

The ion energy distributions (IEDs) in the dual-frequency magnetron sputtering discharges were investigated by retarding field energy analyzer. Increasing power ratio of 2 MHz to 13.56 (27.12 or 60) MHz led to the evolution of IEDs from a uni-modal distribution towards a uni-modal distribution with high-energy peak shoulder and a bi-modal distribution. While increasing power ratio of 13.56 MHz to 27.12 MHz and 27.12 MHz to 60 MHz, led to the increase of peak energy. The evolution of IEDs shape and the increase of peak energy are due to the change of ions responding to the average field of high-frequency period towards the instantaneous sheath potential of low-frequency period.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Discharge current modes of high power impulse magnetron sputtering

Based on the production and disappearance of ions and electrons in the high power impulse magnetron sputtering plasma near the target, the expression of the discharge current is derived. Depending on the slope, six possible modes are deduced for the discharge current and the feasibility of each mode is discussed. The discharge parameters and target properties are simplified into the discharge voltage, sputtering yield, and ionization energy which mainly affect the discharge plasma. The relationship between these factors and the discharge current modes is also investigated.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Commissioning of a modulated pulse-power magnetron sputtering system for depositing niobium thin films

A modulated pulse-power magnetron sputtering system (MPPMS) was commissioned and used to deposit niobium on copper. MPPMS utilizes a modulated pulse train with high peak-to-average energy ratios, thereby increasing the energy density leading to the production of the energetic ions. The MPPMS modulator was designed and constructed based on large voltage/current IGBT modules, which can be externally modulated, produce bi-polar waveforms, and are readily available. A high voltage power supply provides moderate current to the IGBT module to create the precise pulse structure. The MPPMS system was used to deposit ~1 mm thick, niobium film on a copper substrate held at ~77 K to minimize Nb atom surface diffusion and maximize intrinsic film energy. Finally, the Nb film had an average grain size of ~8 nm.

42 ENGINEERING↗

Arsenic doped p-type zinc oxide films grown by radio frequency magnetron sputtering

As-doped ZnO films were grown by the radio frequency magnetron sputtering method. As the substrate temperature during growth was raised above approx400 deg. C, the films changed from n type to p type. Hole concentration and mobility of approx6x10{sup 17} cm{sup -3} and approx6 cm{sup 2} V{sup -1} s{sup -1} were achieved. The ZnO films were studied by secondary ion mass spectroscopy, x-ray photoelectron spectroscopy (XPS), low temperature photoluminescence (PL), and positron annihilation spectroscopy (PAS). The results were consistent with the As{sub Zn}-2V{sub Zn} shallow acceptor model proposed by Limpijumnong et al. [Phys. Rev. Lett. 92, 155504 (2004)]. The results of the XPS, PL, PAS, and thermal studies lead us to suggest a comprehensive picture of the As-related shallow acceptor formation.

36 MATERIALS SCIENCE↗

Magnetron-Sputtered Amorphous Metallic Coatings

Amorphous coatings of refractory metal/metalloid-based alloys deposited by magnetron sputtering provide extraordinary hardness and wear resistance. Sputtering target fabricated by thoroughly mixing powders of tungsten, rhenium, and boron in stated proportions and pressing at 1,200 degrees C and 3,000 lb/in. to second power (21 MPa). Substrate lightly etched by sputtering before deposition, then maintained at bias of - 500 V during initial stages of film growth while target material sputtered onto it. Argon gas at pressure used as carrier gas for sputter deposition. Coatings dense, pinhole-free, extremely smooth, and significantly resistant to chemical corrosion in acidic and neutral aqueous environments.

Thakoor, A. P.↗