SEARCH · Engineering Papers

Results for “Low Reynolds Number”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8

All sources NASA NTRS DOE OSTI

NASA NTRS1986

A smoke-wire study of low Reynolds number flow over a NASA LRN(1) - 1007 airfoil section

Smoke-filament visualization photographs are presented for two-dimensional flow over a NASA LRN(1) - 1007 airfoil section designed specifically for high-efficiency operation at low chord Reynolds numbers. Results are included for chord Reynolds numbers of 60,000, 100,000, and 220,000 and for angles of attack ranging from 0 to 16 degrees. Two kinds of laminar separation bubble are found to develop in the flow over the airfoil. The sites and characteristics of formation of these bubbles are described, and their dimensional properties are estimated. The transition-to-turbulence Reynolds numbers, surface pressure coefficient distributions, and lift coefficients deduced from the measured coefficients are compared with those obtained by other authors.

Fisher, S. S.↗

NASA NTRS1989

A turbulent boundary layer at low Reynolds number with adverse pressure gradient

The evolution of a low Re(theta) turbulent boundary layer in an adverse pressure gradient (APG) is studied for comparison with CFD simulations by Spalart (1988). A short region of favorable pressure gradient is applied first to establish a self-preserving layer which is a suitable initial condition for the simulations. The APG is then applied rapidly such that Beta(x) of about 2 for Re(theta) of about 1500.

Watmuff, J. H.↗

NASA NTRS1990

Experiments on a separation bubble over an Eppler 387 airfoil at low Reynolds numbers using thin-film arrays

Experiments carried out at the NASA Langley Low-Turbulence Pressure Tunnel on an Eppler 387 airfoil at several angles of attack for Reynolds numbers of 100,000 to 300,000 are discussed. Cross-correlations and phase diagrams are used in calculating velocities, while spectra are used in checking for amplified frequencies, and coherence plots for causality. Hot-film measurements, oil-flow visualization, pressure measurements, and Drela code are compared for finding the leading and trailing edges of the bubble. It is observed that all methods agree in showing the beginning and end of the separation bubble, the velocity measurements agree in magnitude for the lower velocities, and wave packets appear in the cross-correlation.

Mousseux, Marc C.↗

NASA NTRS1983

The influence of free-stream disturbances on low Reynolds number airfoil experiments

The results of an investigation of the influence of free stream disturbances on the lift and drag performance of the Lissaman 7769 airfoil are presented. The wind tunnel disturbance environment is described using hot-wire anemometer and sound pressure level measurements. The disturbance level is increased by the addition of a 'turbulence screen' upstream of the test section and/or the addition of a flow restrictor downstream of the test section. For the Lissaman airfoil it was found that the problems associated with obtaining accurate wind tunnel data at low chord Reynolds numbers (i.e., below 200,000) are compounded by the extreme sensitivity of the boundary layers to the free stream disturbance environment. The effect of free stream disturbances varies with magnitude, frequency content, and source of the disturbance.

Mueller, T. J.↗

NASA NTRS1990

Subsonic and transonic low-Reynolds-number airfoils with reduced pitching moments

A subsonic and a transonic airfoil are presented for application in a high-altitude long-endurance aircraft and a very-high-altitude aircraft, respectively. The subsonic airfoil is designed for a lift coefficient c(l) = 1.4 at a chord Reynolds number Re = 700,000 and a very low Mach number. The transonic airfoil is designed for c(l) = 1.0 at Re = 500,000 and a transonic Mach number M = 0.7. Both airfoils are developed to perform as well or better than previously designed airfoils. However, the present airfoils are developed for a constrained pitching moment to reduce aircraft trim drag and to relieve, to some extent, the torsional loads in the typically high-aspect-ratio wings. The beneficial effects of a cruise flap and of boundary-layer transition control on the off-design performance characteristics are illustrated.

Van Dam, C. P.↗

NASA NTRS1990

An experimental investigation of a low Reynolds number turbulent boundary layer subject to an adverse pressure gradient

The evolution of a low Re(sub theta) turbulent boundary layer in an adverse pressure gradient (APG) is being studied for comparison with direct numerical simulations by Spalart. A short region of favorable pressure gradient (FPG) is applied first to establish a self preserving layer with Re(sub theta) equals approx. 600, which is a suitable initial condition for simulations. The APG is then applied rapidly such that beta equals approx. 2 at Re(sub theta) equals approx. 1500. The streamwise extent of the measurements exceeds the current capabilities of direct simulation so that the results should also serve as a useful data base for Reynolds averaged boundary layer prediction methods and in the future for direct simulation schemes as computer technology evolves.

Watmuff, J. H.↗

NASA NTRS1983

An experimental investigation of the low Reynolds number performance of the Lissaman 7769 airfoil

A Lissaman 7769 airfoil, used on the Gossamer Condor and Gossamer Albatross human-powered aircraft, was tested in a low turbulence subsonic wind tunnel. Lift and drag data were collected at chord Reynolds numbers of 100,000, 150,000, 200,000, 250,000, and 300,000; at angles of attack from -10 to +20 deg by using an external strain gage force balance. Lift curves, drag curves, and drag polars were generated from both uncorrected data and data corrected for wind tunnel blockage effects. A flow visualization study was performed to correlate with the force data. The results of the investigation have shown that the airfoil exhibits a significant degradation in performance for chord Reynolds numbers below 150,000.

Conigliaro, P. E.↗

NASA NTRS1980

Experimental studies of the laminar separation bubble on a two-dimensional airfoil at low Reynolds numbers

The laminar separation, transition and turbulent reattachment near the leading edge of a two-dimensional NACA 663-018 airfoil were investigated using a low speed, smoke visualization wind tunnel. Lift and drag force measurements were made using an external strain gauge balance for a chord Reynolds number range of 40,000 to 400,000. An extensive flow visualization study was performed and correlated with the force measurements. Experiments were also conducted with distributed surface roughness at the leading edge and external acoustic excitation to influence the development of the airfoil boundary layer. This study delineates the effects of angle of attack and chord Reynolds number on the separation bubble characteristics and airfoil performance

Mueller, T. J.↗

NASA NTRS1985

Low Reynolds number separation bubble research at UTRC

The facilities and techniques being applied in investigations of laminar separation bubbles on low Re airfoils at the United Technologies Research Center are described. The research is focused on developing a database and predictive models for use in designing compressor, fan and turbine blades. Flow data are gathered primarily by laser Doppler velocimetry. Experimental procedures are being devised which will permit formation of a short bubble for characterizations of the velocity profiles in and around the bubble and boundary layer. Further tests are directed at defining the size and location of the bubble and the transition in the separated shear layer. The sensitivity of the bubble to alterations in the Re, pressure gradient, turbulence intensity and the turbulence scales will be examined. The effects of surface curvature and roughness on the bubble will also be studied. Details of the wind tunnel facility and the steps being taken to define conditions for reliably producing the short bubble are outlined.

Patrick, W. P.↗

NASA NTRS1979

On the laminar separation, transition, and turbulent reattachment of low Reynolds number flows near the leading edge of airfoils

The laminar separation, transition, and turbulent reattachment near the leading edge of a cylindrical nose-constant thickness airfoil model were investigated using a low turbulence, low speed smoke wind tunnel. The locations of separation, transition, and reattachment were obtained from smoke flow photographs and surface oil flow techniques for chord Reynolds numbers from about 150,000 to 470,000. These visual data combined with static pressure distributions and lift and drag measurements delineate the effects of angle of attack, flap deflection angle, and chord Reynolds number on the separation bubble characteristics. The data concerning the length of the laminar and turbulent portions of the bubble agree with the empirical prediction methods for short bubbles.

Arena, A. V.↗

NASA NTRS1985

An analysis of a separation bubble transition criterion at low Reynolds numbers

Factors which influence the criterion governing the length of the laminar region of a separation bubble on an airfoil at low Re were investigated. The criterion is the onset of separation when a critical Re value is surpassed. Wind tunnel data were gathered for the flow around a NACA 66(3)-018 airfoil at Re from 50,000-200,000. The data were taken with either hot-wire anemometers or pressure taps. The value of the critical Re was influenced by the chord Re, the angle of attack and the level of turbulence in the free stream. However, the turbulence levels examined, up to 0.184 percent, did not greatly affect the critical Re. Further characterizations of the effects of the three factors on the critical Re are necessary before the important features of separation bubbles can be identified with an acceptable level of certainty.

Schmidt, G. S.↗

NASA NTRS1987

An investigation of turbulence structure in a low-Reynolds-number incompressible turbulent boundary

An existing high turbulence intensity level (5%) atmospheric boundary-layer wind tunnel has been successfully converted to a relatively low level turbulence (0.3%) wind tunnel through extensive modification, testing, and calibration. A splitter plate was designed, built, and installed into the wind-tunnel facility to create thick, mature, two-dimensional turbulent boundary layer flow at zero pressure gradient. Single and cross hot-wire measurements show turbulent boundary layer characteristics of good quality with unusually large physical size, i.e., viscous sublayer of the order of 1 mm high. These confirm the potential ability of the tunnel to be utilized for future high-quality near-wall turbulent boundary layer measurements. It compares very favorably with many low turbulence research tunnels.

White, B. R.↗

NASA NTRS1977

Three-dimensional low Reynolds number flows with a free surface

The two-dimensional leveling problem (Degani, Gutfinger, 1976) is extended to three dimensions in the case where the flow Re number is very low and attention is paid to the free surface boundary condition with surface tension effects included. The no-slip boundary condition on the wall is observed. The numerical solution falls back on the Marker and Cell (MAC) method (Harlow and Welch, 1965) with the computation region divided into a finite number of stationary rectangular cells (or boxes in the 3-D case) and fluid flow traverses the cells (or boxes).

Degani, D.↗

NASA NTRS2006

Low Reynolds Number Aerodynamic Characteristics of Several Airplane Configurations Designed to Fly in the Mars Atmosphere at Subsonic Speeds

A 1/4-scale wind tunnel model of an airplane configuration developed for short duration flight at subsonic speeds in the Martian atmosphere has been tested in the Langley Research Center Transonic Dynamics Tunnel. The tunnel was pumped down to extremely low pressures to represent Martian Mach/Reynolds number conditions. Aerodynamic data were obtained and upper and lower surface wind pressures were measured at one spanwise station on some configurations. Three unswept wings of the same planform but different airfoil sections were tested. Horizontal tail incidence was varied as was the deflection of plain and split trailing-edge flaps. One unswept wing configuration was tested with the lower part of the fuselage removed and the vertical/horizontal tail assembly inverted and mounted from beneath the fuselage. A sweptback wing was also tested. Tests were conducted at Mach numbers from 0.50 to 0.90. Wing chord Reynolds number was varied from 40,000 to 100,000 and angles of attack and sideslip were varied from -10deg to 20deg and -10deg to 10deg, respectively.

Re, Richard J.↗

NASA NTRS1987

Comparative low Reynolds number tests of NACA 64-210, NACA 0012, and Wortmann FX67-K170 airfoils in heavy rain

The effect of simulated rain at 1000 mm/h on the aerodynamic performance of NACA 64-210, NACA 0012, and Wortmann FX67-K170 airfoils is investigated experimentally at Reynolds number 310,000, freestream velocity 70 mph, and angle of attack -10 to +20 deg in the 1 x 1-ft section of the MIT low-turbulence wind tunnel. The results are presented graphically and characterized in detail. Rain is found to produce lift degradation of 5-25 percent, an effect attributed to development of a premature transition at the leading edge followed (after 1-10 s) by alteration of the profile by surface water runback.

Hansman, R. John, Jr.↗

NASA NTRS2018

Effect of Simulated Scalloped Ice on the Aerodynamics of a Swept-Wing at Low-Reynolds Number

This paper studied the aerodynamic effects of a single scalloped ice accretion and two lower fidelity ice-shape simulations. These data were compared to the aerodynamics of a clean 8.9% scale CRM65 semispan wing model at a Reynolds number of 1.6 x 10(exp 6). The clean wing experienced an aggressive, tip-first stall and showed a small, strong leading-edge vortex at lower angle-of-attack while the iced cases showed larger, seemingly weaker leading-edge vortices at similar angles. The size of these vortices is larger for the low-fidelity ice shape. The stall pattern for the iced cases was also tip-first, but more gradual than the clean wing. The high-fidelity ice shape produced streamwise flow features over the upper surface of the wing due to flow moving through gaps that exist in the ice shape geometry that disrupted the formation of the leading-edge vortices, changing the aerodynamics of the wing. These gaps do not exist in the low-fidelity shape. The low-fidelity scallop ice shape was non-conservative in its aerodynamic penalties compared to the full high-fidelity case.

Aircraft icing↗

NASA NTRS1987

An experimental low Reynolds number comparison of a Wortmann FX67-K170 airfoil, a NACA 0012 airfoil and a NACA 64-210 airfoil in simulated heavy rain

Wind tunnel experiments were conducted on Wortmann FX67-K170, NACA 0012, and NACA 64-210 airfoils at rain rates of 1000 mm/hr and Reynolds numbers of 310,000 to compare the aerodynamic performance degradation of the airfoils and to attempt to identify the various mechanisms which affect performance in heavy rain conditions. Lift and drag were measured in dry and wet conditions, a variety of flow visualization techniques were employed, and a computational code which predicted airfoil boundary layer behavior was used. At low angles of attack, the lift degradation in wet conditions varied significantly between the airfoils. The Wortmann section had the greatest overall lift degradation and the NACA 64-210 airfoil had the smallest. At high angles of attack, the NACA 64-210 and 0012 airfoils had improved aerodynamic performance in rain conditions due to an apparent reduction of the boundry layer separation. Performance degradation in heavy rain for all three airfoils at low angles of attack could be emulated by forced boundary layer transition near the leading edge. The secondary effect occurs at time scales consistent with top surface water runback times. The runback layer is thought to effectively alter the airfoil geometry. The severity of the performance degradation for the airfoils varied. The relative differences appeared to be related to the susceptibility of each airfoil to premature boundary layer transition.

Craig, Anthony P.↗

NASA NTRS2003

Low Reynolds Number Droplet Combustion In CO2 Enriched Atmospheres In Microgravity

The effect of radiative feedback from the gas phase in micro-gravity combustion processes has been of increasing concern because of the implications in the selection and evaluation of appropriate fire suppressants. The use of CO2, an optically thick gas in the infrared region of the electromagnetic spectrum, has garnered widespread acceptance as an effective fire suppressant for most ground based applications. Since buoyant forces often dominate the flow field in 1-g environments the temperature field between the flame front and the fuel surface is not significantly affected by gas phase radiative absorption and re-emission as these hot gases are quickly swept downstream. However, in reduced gravity environments where buoyant-driven convective flows are negligible and where low-speed forced convective flows may be present at levels where gas phase radiation becomes important, then changes in environment that enhance gas phase radiative effects need to be better understood. This is particularly true in assessments of flammability limits and selection of appropriate fire suppressants for future space applications. In recognition of this, a ground-based investigation has been established that uses a droplet combustion configuration to systematically study the effects of enhanced gas phase radiation on droplet burn rates, flame structure, and radiative output from the flame zone.

Hicks, M. C.↗