Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “JOINING”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8

Low Activation Joining of SiC/SiC Composites for Fusion Applications: Modeling Miniature Torsion Tests with Elastic and Elastic-Plastic Models

The use of SiC and SiC-composites in fission or fusion environments requires joining methods for assembling systems. The international fusion community designed miniature torsion specimens for joint testing and irradiation in test reactors with limited irradiation volumes. These torsion specimens fail out-of-plane when joints are strong and when elastic moduli are within a certain range compared to SiC, which causes difficulties in determining shear strengths for joints or for comparing unirradiated and irradiated joints. A finite element damage model was developed that indicates fracture is likely to occur within the joined pieces to cause out-of-plane failures for miniature torsion specimens when a certain modulus and strength ratio between the joint material and the joined material exists. The model was extended to treat elastic-plastic joints such as SiC/epoxy and steel/epoxy joints tested as validation of the specimen design.

Henager, Charles H.↗

Low Activation Joining of SiC/SiC Composites for Fusion Applications: Modeling Miniature Torsion Tests

The use of SiC and SiC-composites in fission or fusion environments appears to require joining methods for assembling systems. The international fusion community has designed miniature torsion specimens for joint testing and for irradiation in HFIR. Therefore, miniature torsion joints were fabricated using displacement reactions between Si and TiC to produce Ti3SiC2 + SiC joints with CVD-SiC that were tested in shear prior to and after HFIR irradiation. However, these torsion specimens fail out-of-plane, which causes difficulties in determining a shear strength for the joints or for comparing unirradiated and irradiated joints. A finite element damage model has been developed that indicates fracture is likely to occur within the joined pieces to cause out-of-plane failures for miniature torsion specimens when a certain modulus and strength ratio between the joint material and the joined material exists. The implications for torsion shear joint data based on this sample design are discussed.

Henager, Charles H.↗

Pulse joining cartridges

A pulsed joining tool includes a tool body that defines a cavity that receives an inner tubular member and an outer tubular member and a pulse joining cartridge. The tubular members are nested together with the cartridge being disposed around the outer tubular member. The cartridge includes a conductor, such as a wire or foil, that extends around the outer tubular member and is insulated to separate a supply segment from a return segment. A source of stored electrical energy is discharged through the conductor to join the tubular members with an electromagnetic force pulse.

25 ENERGY STORAGE↗

Joining of advanced materials by plastic deformation

A method for utilizing plastic deformation resulting from grain boundary sliding with or without a novel joint compound that leads to the joining of advanced ceramic materials, intermetallics, and cermets. A joint formed by this approach is as strong as or stronger than the materials joined. The method does not require elaborate surface preparation or application techniques. The method also allows for the formation of transparent joints between two subunits of a construct joined via plastic deformation. The method can be used to tailor residual stresses and maintain native porosity.

36 MATERIALS SCIENCE↗

Study of mechanical joint strength of aluminum alloy 7075-T6 and dual phase steel 980 welded by friction bit joining and weld-bonding under corrosion medium

We have employed a unique solid-sate joining process, called friction bit joining (FBJ), to spot weld aluminum alloy (AA) 7075-T6 and dual phase (DP) 980 steel. Static joint strength was studied in the lap shear tension configuration. In addition, weld-bonding (adhesive + FBJ) joints were studied in order to evaluate the ability of adhesive to mitigate the impact of corrosion on joint properties. Accelerated laboratory cyclic corrosion tests were carried out for both FBJ only and weld-bonding joints. Furthermore, the FBJ only joints that emerged from corrosion testing had lap shear failure loads that were significantly lower than freshly prepared joints. However, weld-bonding specimens retained more than 80% of the lap shear failure load of the freshly prepared weld-bonding specimens. Moreover, examination of joint cross sections confirmed that the presence of adhesive in the weld-bonding joints mitigated the effect of the corrosion environment, compared to FBJ only joints.

36 MATERIALS SCIENCE↗

Solid-State Joining of Thick-Section Dissimilar Materials using a New Friction Stir Dovetailing (FSD) Process

Solid-state joining of thick section aluminum to steel plate has been achieved using a new process called Friction Stir Dovetailing (FSD). In FSD, a custom designed pin tool is used to flow a lower melting point material (AA6061) into dovetail grooves machined into the surface of an underlying higher melting point material (Rolled Homogeneous Armor – RHA). Repeating dovetails form a mechanical interlocking structure akin to metallic Velcro. In this study, AA6061 sections ranging in thickness from 1.5” to 3.0” are joined to 0.5” thick RHA plates. The effectiveness of FSD is demonstrated through tensile test data which shows specimens failing in the processed aluminum rather than at the joint interface. Numerical simulations are presented which highlight the importance of optimizing dovetail geometry. The effect of process parameters on joint strength, microstructure, and hardness are also discussed.

dissimilar metals joining↗

Joining sheet aluminum AA6061-T4 to cast magnesium AM60B by vaporizing foil actuator welding: Input energy, interface, and strength

Dissimilar joining of sheet aluminum AA6061-T4 to cast magnesium AM60B was achieved by vaporizing foil actuator welding (VFAW). Three input energy levels were used (6, 8, and 10 kJ), and as a trend, higher input energies resulted in progressively higher flyer velocities, more pronounced interfacial wavy features, larger weld zones, higher peel strengths, and higher peel energies. In all cases, weld cross section revealed a soundly bonded interface characterized by well-developed wavy features and lack of voids and continuous layers of intermetallic compounds (IMCs). At 10 kJ input energy, flyer speed of 820 m/s, peel strength of 22.4 N/mm, and peel energy of 5.2 J were obtained. In lap-shear, failure occurred in AA6061- T4 flyer at 97% of the base material’s peak tensile load. Peel samples failed along the weld interface, and the AM60B-side of the fracture surface showed thin, evenly-spaced lines of Al residuals which had been torn out of the base AA6061-T4 in a ductile fashion and transferred over to the AM60B side, indicating very strong AA6061-T4/AM60B bond in these areas. Furthermore, this work demonstrates VFAW’s capability in joining dissimilar lightweight metals such as Al/Mg, which is expected to be a great enabler in the ongoing push for vehicle weight reduction.

36 MATERIALS SCIENCE↗

Joining Light Metals with Polymer Composites Through Metal Overcasting

This work investigates a unique technique to join aluminum (Al) and magnesium (Mg) alloys to carbon fiber reinforced polymer (CFRP) composites without the use of adhesives or mechanical fasteners. The joints were made using an overcasting technique where the molten alloys were cast around the polymer composites using high pressure die casting method. Rapid cooling during casting allowed the composite to be embedded inside the cast metal without causing any gross damage to the former even though the molten metal temperature exceeded the melting point of the composite matrix by several 100’s of deg. C. The metal/composite interface was examined using optical microscopy and x-ray imaging and the joint strength was examined through tensile testing. Although evidence of polymer melting was evident in the x-ray images, the embedded section of the composite coupons retained their overall shape and integrity. Preliminary tension tests on Al/CFRP composites showed strength degradation of the CFRP and it failed near the metal/CFRP interface (outside the joint). Strength degradation in the CFRP suggests that the overcasting process needs further optimization to minimize thermal excursion in the CFRP. Nevertheless, the overcasting process shows great promise as a unique joining technique with application in fabricating light-weight structures for automotive and transportation industries.

overcasting, Casting, Mg Castings, Al Casting, Joi↗

Joining technique for in-oven/autoclave molds manufactured by large scale polymer additive manufacturing

Large scale additive manufacturing (AM) of fiber-reinforced polymer composites has gained traction in the mold and die community over the last decade, largely due to reduced material cost and lead time. However, limitations in mold size remain present due to printer volume constraints and costs associated with large format machines. Here, this paper describes a method for producing additively manufactured polymer molds in segments with an O-ring joint design, which can be machined and subsequently assembled for autoclave applications. The developed joining mechanism allows for maintaining the vacuum integrity during the cure cycle while accounting for the anisotropic nature of the additively manufactured polymer molds. Over a range of tested temperatures, 20–200 °C, the multi-part mold joining design was able to achieve full vacuum of ∼73.7 cmHg (29 inchHg) and maintain a vacuum integrity with vacuum losses less than 1.5 cmHg/5min (0.6 inchHg).

Joining↗

Fusion joining of thermoplastic composite wind turbine blades: Lap-shear bond characterization

Wind turbine blades are typically manufactured from a small number of components which are bonded together with an adhesive. Over the life span of a wind turbine, the static and fatigue loads in varying environmental conditions can lead to cracking and/or debonding of the adhesive joints, ultimately leading to blade structural collapse. The objective of this work is to investigate fusion joining of wind turbine blades manufactured using thermoplastic resin. Thermoplastic resins for wind turbine blades can reduce cycle times and energy consumption during manufacturing and facilitate end-of-life recycling and on-site manufacturing. Additionally, fusion joining of these materials can replace adhesives, resulting in stronger and more robust blades. This work showed that, compared to typical adhesives used in wind turbine blades, fusion welding resulted in an increase in both the static and fatigue lap-shear strength as compared to bonded thermoplastic composite coupons. This initial coupon-scale research suggests that there is potential for developing fusion welding techniques for full-scale wind turbine blades.

17 WIND ENERGY↗

Modeling Damage Complexity-Dependent Non-Homologous End-Joining Repair Pathway

Non-homologous end joining (NHEJ) is the dominant DNA double strand break (DSB) repair pathway and involves several repair proteins such as Ku, DNA-PKcs, and XRCC4. It has been experimentally shown that the choice of NHEJ proteins is determined by the complexity of DSB. In this paper, we built a mathematical model, based on published data, to study how NHEJ depends on the damage complexity. Under an appropriate set of parameters obtained by minimization technique, we can simulate the kinetics of foci track formation in fluorescently tagged mammalian cells, Ku80-EGFP and DNA-PKcs-YFP for simple and complex DSB repair, respectively, in good agreement with the published experimental data, supporting the notion that simple DSB undergo fast repair in a Ku-dependent, DNA-PKcs-independent manner, while complex DSB repair requires additional DNA-PKcs for end processing, resulting in its slow repair, additionally resulting in slower release rate of Ku and the joining rate of complex DNA ends. Based on the numerous experimental descriptions, we investigated several models to describe the kinetics for complex DSB repair. An important prediction of our model is that the rejoining of complex DSBs is through a process of synapsis formation, similar to a second order reaction between ends, rather than first order break filling/joining. The synapsis formation (SF) model allows for diffusion of ends before the synapsis formation, which is precluded in the first order model by the rapid coupling of ends. Therefore, the SF model also predicts the higher number of chromosomal aberrations observed with high linear energy transfer (LET) radiation due to the higher proportion of complex DSBs compared to low LET radiation, and an increased probability of misrejoin following diffusion before the synapsis is formed, while the first order model does not provide a mechanism for the increased effectiveness in chromosomal aberrations observed.

59 BASIC BIOLOGICAL SCIENCES↗

Advances in Dissimilar Metals Joining through Temperature Control of Friction Stir Welding

Lightweighting of vehicles and portable structures is an important undertaking. Multi-material design is required to achieve conflicting design targets such as cost, stiffness, and weight. Friction stir welding (FSW) variants, such as friction stir dovetailing and friction stir scribe, are enabling technologies for joining of dissimilar metals. This work shows that FSW variants are capable of joining aluminum to steel. Characteristics of metallurgical bonding at the dissimilar material interface are strongly affected by weld temperature. Control of FSW process temperature enables metallurgical bonding with suppressed formation of intermetallics at the dissimilar material interface resulting in improved mechanical properties relative to competing techniques. Temperature control is a powerful tool for process development and to ensure weld quality of dissimilar material welds.

Aluminum to Steel Joining, Friction stir welding, ↗

Research and Development Opportunities for Joining Technologies in HVAC&R

The Building Technologies Office (BTO) works with researchers and industry partners to develop and deploy technologies that can substantially reduce energy consumption and greenhouse gas (GHG) emissions in residential and commercial buildings. This opportunity assessment aims to advance BTO’s energy savings, GHG reduction, and other program goals by identifying research and development (R&D) initiatives for joining technologies in heating, ventilation, air-conditioning, and refrigeration (HVAC&R) systems. Improving joining technologies for HVAC&R equipment has the potential to increase lifetime equipment operating efficiency, decrease equipment and project cost, and most importantly reduce hydroflourocarbon (HFC) refrigerant leakage to support HFC phasedown and GHG reduction goals.

brazing and joining technologies↗

Crack-Free Joining of High-Strength AA7055 Sheets by Friction Based Self-Piercing Riveting with the Aid of Numerical Design

Unique friction-based self-piercing riveting (F-SPR) was employed to join high-strength, low-ductility aluminum alloy 7055 for lightweight vehicle applications. This study aimed to maximize the joint strength of the AA7055 F-SPR joint while avoiding cracking issues due to low ductility at room temperature. A fully coupled Eulerian–Lagrangian (CEL) model was employed to predict the process temperature during F-SPR, and the temperature field was then mapped onto a 2D axisymmetric equivalent model for accelerated numerical analysis. The geometry, dimensions, and material strength of the rivet, as well as the depth of the die cavity and plunging depth, were investigated to enhance joint formation. Also, a static finite-element analysis model was developed to predict and analyze the stress distribution in the rivet under different mechanical testing loading conditions. Overall, the numerical model showed good agreement with the experiment results, such as joint formation and mechanical joint strength. With the aid of virtual fabrication through numerical modeling, the joint design iterations and process development time of F-SPR were greatly reduced regarding the goal of lightweight, high-strength aluminum joining.

36 MATERIALS SCIENCE↗

Plasma Enhanced Microwave Joining

A new method for plasma enhanced microwave joining of high purity (99.8%) alumina has been developed. The controlled application of a plasma between the adjoining surfaces of two rods permits the initial heating of low microwave absorbing alumina to sufficiently high temperatures where they can effectively absorb microwave energy. With this technology, the adjacent surfaces of alumina rods can be melted and welded together in less than three minutes using approximately 400 watts of microwave energy. Four point bending tests measured fracture strengths of up to 132 MPa at the joined interface.

microwave↗

Air Brazing: A New Method of Ceramic-Ceramic and Ceramic-Metal Joining

A new method of ceramic-ceramic and ceramic-metal joining has emerged over the past several years. Referred to as air brazing, the technique was originally designed and developed for use in fabricating high-temperature solid-state electrochemical devices such as planar SOFCs and oxygen and hydrogen concentrators. The primary advantage of air brazing is that a predominantly metallic joint can be formed directly in air without need of an inert cover gas or the use of surface reactive fluxes. The resulting bond is hermetic, offers excellent room temperature strength, and is inherently resistant to oxidation at high temperature. The key to developing a successful filler metal composition for air brazing is to identify a metal oxide wetting agent that is mutually soluble in a molten noble metal solvent. One particular oxide-metal combination that appears readily suited for this purpose is CuOx-Ag, a system originally of interest in the development of silver clad cuprate-based superconductors. Studies of the equilibrium phases studies in this system indicate that there are two invariant points in the pseudobinary CuOx-Ag phase diagram around which new braze compositions can be developed: 1) a monotectic reaction at 969±1°C, where CuO and a Ag-rich liquid L1 coexist with a second CuOx-rich liquid phase L2 at a composition of xAg/(xAg + xCu) = 0.10±0.03 Ag and 2) a eutectic reaction at 942±1°C, where CuO and Ag coexist with L1 at a composition of xAg/(xAg + xCu) = 0.99±0.005. Specifically, near-eutectic Ag-CuO filler metal compositions have shown good promise in joining electrochemically active ceramics such as yttria-stabilized zirconia, lanthanum strontium manganite, and barium strontium cobalt ferrite, as well as alumina and magnesia. More recently it has been found that various ternary additions can further improve the wetting characteristics of these filler metals, increase their potential operating temperatures, and/or increase the resulting strength of the joint strength. Here we review the basic concept of air brazing and illustrate filler metal selection and design using the Ag-CuO system as an example.

air brazing↗

Joining AA7099 to Ni-Cr-Mo Steel using Friction Stir Dovetailing

Friction stir dovetailing (FSD) was used to join 0.5 inch (12.7 mm) AA7099 to 0.5 inch (12.7 mm) Ni-Cr-Mo steel in a lap configuration. Two new FSD approaches are reported that significantly reduce zinc embrittlement of Fe-Al intermetallic compounds (IMCs) which form during conventional friction stir welding (FSW). The first method uses the general FSD approach where a custom designed tool is employed to extrude the AA7099 into the pre-machined dovetail groove of underlying steel by forming mechanical interlocking and metallurgical bonding simultaneously. The second method uses a two-step approach where FSD of AA6061 is first used to form a silicon-rich Fe-Al IMC within the dovetail groove. AA7099 plate is then joined to the AA6061 within the dovetail using conventional FSW. A discussion of the new FSD technique, joint configurations, and process parameters are provided along with joint microstructural analyses and mechanical performance.

Friction stir dovetailing, FSD, AA7099, AA6061, ro↗

Dissimilar material joining of densified superwood to aluminum by adhesive bonding

Abstract Superwood is a densified wood product that shows promise as a lightweight and renewable alternative for metallic materials. In order for this high-performance new material to be used in multi-material products, it must be able to be joined with other major materials. For example, joining superwood to aluminum would provide a key enabling technology for its use in automotive components since aluminum is presently a major lightweight material for such applications. In this paper, a methacrylate-based adhesive has been identified to provide high lap shear strength (7.5 MPa) for aluminum-to-superwood joints. The aluminum-to-superwood samples were prepared with different amounts of pre-polishing to create openings to the pores in the superwood so adhesive could penetrate into them and create a mechanical interlock, in addition to the hydrogen/chemical bonding at the surface between the methyl methacrylate (MMA) in methacrylate-based adhesive and the cellulose in superwood. For aluminum samples, a thin layer (typically a few nanometers) of oxide film on the surfaces provides hydrogen/chemical bond to MMA structure in the adhesive layer. The failure strength of the superwood-to-aluminum joint sample is about 50% higher than that of natural wood to natural wood joint sample and comparable to that of aluminum-to-aluminum joint sample.

Automation & Control Systems↗