SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Conditions and results of tensile tests of 26 Inconel 718 and four cryoformed stainless steel specimens are presented. Conclusions determine maximum safe hydrogen operating pressure for cryogenic pressure vessels and provide definitive information concerning flaw growth characteristics under the most severe temperature and pressure conditions
Fracture crack propagation in Inconel at room and cryogenic temperatures for surface defective samples
Crack growth threshold investigation of Inconel 718 exposed to high pressure oxygen
Effect of strain gage attachment by spotwelding and bonding on fatigue behavior of Ti-6Al-4V, Rene 41, and Inconel X
Inconel 718 and Al 2219 alloys surface flawed specimens fracture toughness and flaw growth comparison for high pressure hydrogen vessel
Coherent precipitates effect on explosive shock hardening of pure nickel and Inconel alloy sandwich assemblies determined from simultaneous shock loading at specific pressures
Determination of thermal conductivity, electrical resistivity, Lorentz ratio, and thermopower for annealed specimen of Inconel 718 at temperatures from 4 to 300 K
Substructures and properties of Ni, Chromel A, Inconel 600 and TD-NiCr following explosive shock load deformation, using electron microscope
A summary of the materials property information for Inconel alloy 718 is presented. The scope of the information includes physical and mechanical properties at cryogenic, ambient, and elevated temperatures. Information on material procurement, metallurgy of the alloy, corrosion, environmental effects, fabrication, and joining techniques is developed.
Time-dependent notch sensitivity of Inconel 718 sheet occurred at 900 to 1200 F when notched specimens were loaded below the yield strength, and tests on smooth specimens showed that small amounts of creep consumed large fractions of creep-rupture life. The severity of the notch sensitivity decreased with decreasing solution treatment temperature and increasing time and/or temperature of the aging treatment. Elimination of the notch sensitivity was correlated with a change in the dislocation mechanism from shearing to by-passing precipitate particles.
Seamless Inconel 702 tubes with 0.375-in. outside diameter and 0.025-in. wall thickness were tested to failure at temperatures from 1390 to 1575 F and internal helium pressures from 700 to 1800 psi. Lifetimes ranged from 29 to 1561 hr. The creep-rupture strength of the tubes was about 70 percent lower than that of sheet specimens. Larson-Miller correlations and photomicrographs of some specimens are presented.
Results of mechanical-properties and axial-load fatigue and fracture tests performed on thick welded plates of Inconel 718 superalloy are presented. The test objectives were to determine the tensile strength properties and the crack-growth behavior in electron-beam, plasma-arc, and gas tungsten are welds for plates 1.90 cm (0.75 in) thick. Base-metal specimens were also tested to determine the flaw-growth behavior. The tests were performed in room-temperature-air and liquid nitrogen environments. The experimental crack-growth-rate data are correlated with theoretical crack-growth-rate predictions for semielliptical surface flaws.
Time-dependent notch sensitivity of Inconel 718 sheet was observed at 900 F to 1200 F (482 - 649 C). It occurred when edge-notched specimens were loaded below the yield strength and smooth specimen tests showed that small amounts of creep consumed large rupture life fractions. The severity of the notch sensitivity was reduced by decreasing the solution temperature, increasing the time and/or temperature of aging and increasing the test temperature to 1400 F (760 C). Elimination of time-dependent notch sensitivity correlated with a change in dislocation motion mechanism from shearing to by-passing precipitate particles.
The embrittlement of Inconel 718 by exposure to 34.5 MN/sq m hydrogen at ambient temperature was found to be a function of both forming operation and heat treatment. The embrittlement, as measured by reduction of notch strength in hydrogen as compared to helium, was decreased by a fine-grain size and was most severe for coarse-grained structures containing a continuous or nearly continuous precipitate tentatively identified as Ni3Cb. Tests performed on unnotched specimens showed that the strain at which surface cracks initiate in 34.5 MN/sq m hydrogen was approximately 3% and was independent of prior forming operation or heat treatment.
Inconel 718, nickel-based alloy used extensively for high-temperature structural service, welded repeatedly without detriment to its strength. According to NASA report, tests show 12 repairs on same weld joint do not adversely affect ultimate tensile strenth, yield strength, fatigue strength, metallurgical grain structures, or ability of weld joint to respond to post weld heat treatments.
The physical metallurgy of near-solidus integranular cracking in Inconel 718 welds was investigated. The data, although inconclusive, suggest at least two mechanisms which might explain intergranular cracking (microfissuring) in the heat-affected zone of several high temperature alloys. One theory is based on the separation of intergranular liquid while the other involves mechanical failure of solid ligaments surrounded by intergranular liquid. Both mechanisms concentrate strain in the grain boundaries resulting in low strain (1%) intergranular brittleness. The mechanisms reported might also pertain to the physical metallurgy of casting, powder metallurgy sintering and hot isostatic pressing.
Experimental results are presented to show the effect of environmental simulation exposures of convective heating and of radiant heating on the spectral (1.0 to 14 micrometers) and total emittance of oxidized Inconel 617. Convective heating exposures were conducted in an arc heated supersonic wind tunnel using a wedge-shaped specimen configuration. Radiant tests were conducted in dry air at a flow velocity of several meters per second. Convective heating specimens were subjected to 8, 20 and 38 heating cycles of 15-minutes duration and radiant heating specimens were tested for 10, 20, 50 and 100 one-half hour heating cycles. Changes in radiative properties are discussed in terms of changes in composition and morphology resulting from the exposure tests. Total normal emittance did not significantly change from the statically oxidized condition after either type of exposure, and it remained above 0.80 at 1260K for all cases. Although spectral changes were observed on post exposure specimens at wavelengths less than 2.0 micrometers and greater than 15 micrometers, these changes have no influence on total emittance at 1260K.
The amount of columbium which can be removed from Inconel alloy 718 without degrading its high temperature properties was determined. The elements that are substituted are: vanadium and tungsten together and separately; increasing the molybdenum level from 3.0% to 5.8% and increasing the boron to 0.04%.