Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “InSar”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8

Polarimetric SAR Interferometry Evaluation in Mangroves

TanDEM-X (TDX) enables to generate an interferometric coherence without temporal decorrelation effect that is the most critical factor for a successful Pol-InSAR inversion, as have recently been used for forest parameter retrieval. This paper presents mangrove forest height estimation only using single-pass/single-baseline/dual-polarization TDX data by means of new dual-Pol-InSAR inversion technique. To overcome a lack of one polarization in a conventional Pol- InSAR inversion (i.e. an underdetermined problem), the ground phase in the Pol-InSAR model is directly estimated from TDX interferograms assuming flat underlying topography in mangrove forest. The inversion result is validated against lidar measurement data (NASA's G-LiHT data).

Mangrove↗

Unmanned Aerial Vehicle Synthetic Aperture RADAR for Surface Change Monitoring

Space-based and airplane-based synthetic aperture RADAR (SAR) can monitor ground height using interferometric SAR (InSAR) collections. However, fielding the airplane-based SAR is expensive and coordinating the frequency and timing of ground experiments with space-based SAR is challenging. This research explored the possibility of using a small, mobile unmanned aerial vehicle- base (UAV) SAR to see if it could provide a quick and inexpensive InSAR option for the Source Physics Experiment (SPE) Phase III project. Firstly, a local feasibility collection using a UAV-based SAR showed that InSAR products and height measurements were possible, but that in-scene fiducials were needed to assist in digital elevation model (DEM) construction. Secondly, an InSAR collection was planned and executed over the SPE Phase III site using the same platform configuration. We found that the image formation by the SAR manufacturer creates discontinuities, and that noise impacted the generation and accuracy of height maps. These processing artifacts need to be overcome to generate an accurate height map.

47 OTHER INSTRUMENTATION↗

Simulation Studies of Forest Structure using 3D Lidar and Radar Models

The use of lidars and radars to measure forest structure attributes such as height and biomass are being considered for future Earth Observation missions. Large footprint lidar makes a direct measurement of the heights of scatterers in the illuminated footprint and can yield information about the vertical profile of the canopy. Synthetic Aperture Radar (SAR) is known to sense the canopy volume, especially at longer wavelengths and is useful for estimating biomass. Interferometric SAR (InSAR) has been shown to yield forest canopy height information. For example, the height of scattering phase retrieved from InSAR data is considered to be correlated with the three height and the spatial structure of the forest stand. There is much interest in exploiting these technologies separately and together to get important information for carbon cycle and ecosystem science. More detailed information of the electromagnetic radiation interactions within forest canopies is needed. And backscattering models can be of much utility here. As part of a NASA funded project to explore data fusion, a three-dimensional (3D) coherent radar backscattering model and a 3D lidar backscatter models were used to investigate the use of large footprint lidar, SAR and InSAR for characterizing realistic forest scenes. For this paper, we use stem maps and other forest measurements to develop a realistic spatial structure of a spruce-hemlock forest canopy found in Maine, USA. The radar and lidar models used measurements of the 3D forest scene as input and simulated the coherent radar backscattering signature and 1064nm energy backscatter, respectively. The relationships of backscatter derived forest structure were compared with field measurements. In addition, we also had detailed airborne lidar (Laser Imaging Vegetation Sensor, LVIS) data available over the stem map sites that was used to study the accuracies of tree height derived from modeled SAR backscatter and the scattering phase center retrieved from the simulated InSAR data will be compared with the height indices, or other structure parameters derived from the lidar data. These results will address the possible synergies between lidar and radar in data in terms of forest structural information.

Sun, Guoqing↗

GPS Position Time Series @ JPL

Different flavors of GPS time series analysis at JPL - Use same GPS Precise Point Positioning Analysis raw time series - Variations in time series analysis/post-processing driven by different users. center dot JPL Global Time Series/Velocities - researchers studying reference frame, combining with VLBI/SLR/DORIS center dot JPL/SOPAC Combined Time Series/Velocities - crustal deformation for tectonic, volcanic, ground water studies center dot ARIA Time Series/Coseismic Data Products - Hazard monitoring and response focused center dot ARIA data system designed to integrate GPS and InSAR - GPS tropospheric delay used for correcting InSAR - Caltech's GIANT time series analysis uses GPS to correct orbital errors in InSAR - Zhen Liu's talking tomorrow on InSAR Time Series analysis

Precise Point Positioning (PPP)↗

Multibaseline TanDEM-X Mangrove Height Estimation: The Selection of the Vertical Wavenumber

We generated a large-scale mangrove forest height map using multiple TanDEM-X (TDX) interferometric synthetic aperture radar (InSAR) acquisitions with various spatial baselines in order to improve the height estimation accuracy across a wide range of forest heights. The forest height inversion using InSAR data is strongly dependent upon the vertical wavenumber (i.e., perpendicular baseline). First, we investigated the role of the vertical wavenumber in forest height inversion from InSAR data using the sensitivity of the interferometric (volume) coherence to forest height. We used corrected but lower resolution and accuracy Shuttle Radar Topography Mission (SRTM) mangrove height maps as a priori information over Akanda and Pongara National Parks in Gabon to estimate lower and upper boundaries of the vertical wavenumber over test sites from the measured coherence-to-height sensitivity. Only TDX acquisitions within the boundaries of the vertical wavenumber were selected and combined for multibaseline mangrove height inversion. Mangrove forest height was obtained with multibaseline TDX acquisitions and was validated against the reference height derived from field measurement data providing improvements in multibaseline inversion over existing height estimates (i.e., SRTM height) and single-baseline inversions (multibaseline inversion: r(exp 2) = 0.98, root mean square error (RMSE) of 2.73 m; SRTM height: r(exp 2) = 0.86, RMSE = 7.21 m; single-baseline inversions: r(exp 2) = 0.08-0.97, RMSE = 3.86-11.10 m). As a result, to accurately estimate forest heights over a wide range (3-60 m), multibaseline InSAR acquisitions (at least three different baselines) are needed to exclude biases associated with the vertical wavenumber in forest height inversion.

vertical wavenumber.↗

Large-scale product of forest height using a new approach from spaceborne repeat-pass SAR interferometry and LIDAR

Spaceborne SAR interferometry (InSAR) has the potential of mapping the forest height on a global scale and a monthly/weekly basis under all weather conditions, which can improve our understanding of the global carbon dynamics. In previous work, repeatpass SAR interferometry from spaceborne sensors is utilized to create large-scale forest height maps (that are particularly interested for large-scale ecological research) based on a newly developed approach. This paper thus serves as a summary paper and also sheds light on the future directions with improved results. In particular, it will be shown that repeat-pass SAR interferometry is able to create a large-scale forest height mosaic product with RMSE 4 m for forest stands on the order of 20 hectares through using the past spaceborne repeat-pass InSAR observations (i.e. JAXA’s ALOS-1 and ALOS-2) combined with sparse airborne lidar training samples over the forested areas in New England, US. Moreover, the results and performance of this approach can be remarkably improved with several enhancement techniques that can be easily satisfied with use of future spaceborne repeat-pass InSAR and lidar missions (e.g. NASA-ISRO’s NISAR and NASA’s GEDI). The methodology described in this paper can be considered as a complimentary tool to the existing PolInSAR technique and also serves as an observing prototype for the future spaceborne missions of repeatpass InSAR in fusion with lidar (e.g. NISAR and GEDI).

Treuhaft, Robert↗

Predicting Short-Term Deformation in the Central Valley Using Machine Learning

Land subsidence caused by excessive groundwater pumping in Central Valley, California, is a major issue that has several negative impacts such as reduced aquifer storage and damaged infrastructures which, in turn, produce an economic loss due to the high reliance on crop production. This is why it is of utmost importance to routinely monitor and assess the surface deformation occurring. Two main goals that this paper attempts to accomplish are deformation characterization and deformation prediction. The first goal is realized through the use of Principal Component Analysis (PCA) applied to a series of Interferomtric Synthetic Aperture Radar (InSAR) images that produces eigenimages displaying the key characteristics of the subsidence. Water storage changes are also directly analyzed by the use of data from the Gravity Recovery and Climate Experiment (GRACE) twin satellites and the Global Land Data Assimilation System (GLDAS). The second goal is accomplished by building a Long Short-Term Memory (LSTM) model to predict short-term deformation after developing an InSAR time series using LiCSBAS, an open-source InSAR time series package. The model is applied to the city of Madera and produces better results than a baseline averaging model and a one dimensional convolutional neural network (CNN) based on a mean squared error metric showing the effectiveness of machine learning in deformation prediction as well as the potential for incorporation in hazard mitigation models. The model results can directly aid policy makers in determining the appropriate rate of groundwater withdrawal while maintaining the safety and well-being of the population as well as the aquifers’ integrity.

58 GEOSCIENCES↗

Using Sentinel-1 and GRACE satellite data to monitor the hydrological variations within the Tulare Basin, California

Abstract Subsidence induced by groundwater depletion is a grave problem in many regions around the world, leading to a permanent loss of groundwater storage within an aquifer and even producing structural damage at the Earth’s surface. California’s Tulare Basin is no exception, experiencing about a meter of subsidence between 2015 and 2020. However, understanding the relationship between changes in groundwater volumes and ground deformation has proven difficult. We employ surface displacement measurements from Interferometric Synthetic Aperture Radar (InSAR) and gravimetric estimates of terrestrial water storage from the Gravity Recovery and Climate Experiment (GRACE) satellite pair to characterize the hydrological dynamics within the Tulare basin. The removal of the long-term aquifer compaction from the InSAR time series reveals coherent short-term variations that correlate with hydrological features. For example, in the winter of 2018–2019 uplift is observed at the confluence of several rivers and streams that drain into the southeastern edge of the basin. These observations, combined with estimates of mass changes obtained from the orbiting GRACE satellites, form the basis for imaging the monthly spatial variations in water volumes. This approach facilitates the quick and effective synthesis of InSAR and gravimetric datasets and will aid efforts to improve our understanding and management of groundwater resources around the world.

54 ENVIRONMENTAL SCIENCES↗

Remote sensing of ocean wave spectra by interferometric synthetic aperture radar

Ocean surface waves can be clearly observed by SAR in the interferometric configuration (INSAR) due to the ability of INSAR to provide images of the local surface velocity field. It is shown here that INSAR can be used to obtain wavenumber spectra that are in agreement with power spectra measured in situ. This new method has considerable potential to provide instantaneous spatial information about the structure of ocean wave fields.

Marom, M.↗

Relating Vegetation Aerodynamic Roughness Length to Interferometric SAR Measurements

In this paper, we investigate the feasibility of estimating aerodynamic roughness parameter from interferometric SAR (INSAR) measurements. The relation between the interferometric correlation and the rms height of the surface is presented analytically. Model simulations performed over realistic canopy parameters obtained from field measurements in boreal forest environment demonstrate the capability of the INSAR measurements for estimating and mapping surface roughness lengths over forests and/or other vegetation types. The procedure for estimating this parameter over boreal forests using the INSAR data is discussed and the possibility of extending the methodology over tropical forests is examined.

Saatchi, Sassan↗

Estimating Forest Vertical Structure from Multialtitude, Fixed-Baseline Radar Interferometric and Polarimetric Data

Parameters describing the vertical structure of forests, for example tree height, height-to-base-of-live-crown, underlying topography, and leaf area density, bear on land-surface, biogeochemical, and climate modeling efforts. Single, fixed-baseline interferometric synthetic aperture radar (INSAR) normalized cross-correlations constitute two observations from which to estimate forest vertical structure parameters: Cross-correlation amplitude and phase. Multialtitude INSAR observations increase the effective number of baselines potentially enabling the estimation of a larger set of vertical-structure parameters. Polarimetry and polarimetric interferometry can further extend the observation set. This paper describes the first acquisition of multialtitude INSAR for the purpose of estimating the parameters describing a vegetated land surface. These data were collected over ponderosa pine in central Oregon near longitude and latitude -121 37 25 and 44 29 56. The JPL interferometric TOPSAR system was flown at the standard 8-km altitude, and also at 4-km and 2-km altitudes, in a race track. A reference line including the above coordinates was maintained at 35 deg for both the north-east heading and the return southwest heading, at all altitudes. In addition to the three altitudes for interferometry, one line was flown with full zero-baseline polarimetry at the 8-km altitude. A preliminary analysis of part of the data collected suggests that they are consistent with one of two physical models describing the vegetation: 1) a single-layer, randomly oriented forest volume with a very strong ground return or 2) a multilayered randomly oriented volume; a homogeneous, single-layer model with no ground return cannot account for the multialtitude correlation amplitudes. Below the inconsistency of the data with a single-layer model is followed by analysis scenarios which include either the ground or a layered structure. The ground returns suggested by this preliminary analysis seem too strong to be plausible, but parameters describing a two-layer compare reasonably well to a field-measured probability distribution of tree heights in the area.

Treuhaft, Robert N.↗

Integrated Analysis of Interferometric SAR, Satellite Altimetry and Hydraulic Modeling to Quantify Louisiana Wetland Dynamics

Wetland loss in Louisiana has been accelerating due primarily to anthropogenic and nature processes, and is being advocated as a problem with national importance. Accurate measurement or modeling of wetland-wide water level changes, its varying extent, its storage and discharge changes resulting in part from sediment loads, erosion and subsidence are fundamental to assessment of hurricane-induced flood hazards and wetland ecology. Here, we use innovative method to integrate interferometric SAR (InSAR) and satellite radar altimetry for measuring absolute or geocentric water level changes and applied the methodology to remote areas of swamp forest in coastal Louisiana. Coherence analysis of InSAR pairs suggested that the HH polarization is preferred for this type of observation, and polarimetric analysis can help to identi:fy double-bonnce backscattering areas in the wetland. Envisat radar altimeter-measured 18- Hz (along-track sampling of 417 m) water level data processed with regional stackfile method have been used to provide vertical references for water bodies separated by levees. The high-resolution (approx.40 m) relative water changes measured from ALOS PALSAR L-band and Radarsat-l C-band InSAR are then integrated with Envisat radar altimetry to obtain absolute water level. The resulting water level time series were validated with in situ gauge observations within the swamp forest. Furthermore, we compare our water elevation changes with 2D flood modeling from LISFLOOD hydrodynamic model. Our study demonstrates that this new technique allows retrospective reconstruction and concurrent monitoring of water conditions and flow dynamics in wetlands, especially those lacking gauge networks.

Lee, Hyongki↗

Calibration of Two-dimensional Floodplain Modeling in the Atchafalaya River Basin Using SAR Interferometry

Two-dimensional (2D) satellite imagery has been increasingly employed to improve prediction of floodplain inundation models. However, most focus has been on validation of inundation extent, with little attention on the 2D spatial variations of water elevation and slope. The availability of high resolution Interferometric Synthetic Aperture Radar (InSAR) imagery offers unprecedented opportunity for quantitative validation of surface water heights and slopes derived from 2D hydrodynamic models. In this study, the LISFLOOD-ACC hydrodynamic model is applied to the central Atchafalaya River Basin, Louisiana, during high flows typical of spring floods in the Mississippi Delta region, for the purpose of demonstrating the utility of InSAR in coupled 1D/2D model calibration. Two calibration schemes focusing on Manning s roughness are compared. First, the model is calibrated in terms of water elevations at a single in situ gage during a 62 day simulation period from 1 April 2008 to 1 June 2008. Second, the model is calibrated in terms of water elevation changes calculated from ALOS PALSAR interferometry during 46 days of the image acquisition interval from 16 April 2008 to 1 June 2009. The best-fit models show that the mean absolute errors are 3.8 cm for a single in situ gage calibration and 5.7 cm/46 days for InSAR water level calibration. The optimum values of Manning's roughness coefficients are 0.024/0.10 for the channel/floodplain, respectively, using a single in situ gage, and 0.028/0.10 for channel/floodplain the using SAR. Based on the calibrated water elevation changes, daily storage changes within the size of approx 230 sq km of the model area are also calculated to be of the order of 107 cubic m/day during high water of the modeled period. This study demonstrates the feasibility of SAR interferometry to support 2D hydrodynamic model calibration and as a tool for improved understanding of complex floodplain hydrodynamics

Hahn Chul Jung↗

Deformation, Ecosystem Structure, and Dynamics of Ice (DESDynI)

The National Research Council Earth Science Decadal Survey, Earth Science Applications from Space, recommends that DESDynI (Deformation, Ecosystem Structure, and Dynamics of Ice), an integrated L-band InSAR and multibeam Lidar mission, launch in the 2010- 2013 timeframe. The mission will measure surface deformation for solid Earth and cryosphere objectives and vegetation structure for understanding the carbon cycle. InSAR has been used to study surface deformation of the solid Earth and cryosphere and more recently vegetation structure for estimates of biomass and ecosystem function. Lidar directly measures topography and vegetation structure and is used to estimate biomass and detect changes in surface elevation. The goal of DESDynI is to take advantage of the spatial continuity of InSAR and the precision and directness of Lidar. There are several issues related to the design of the DESDynI mission, including combining the two instruments into a single platform, optimizing the coverage and orbit for the two techniques, and carrying out the science modeling to define and maximize the scientific output of the mission.

Donnellan, Andrea↗

Using Sentinel-1 and GRACE Satellite Data to Monitor the Hydrological Variations Within the Tulare Basin, California

Subsidence induced by groundwater depletion is a grave problem in many regions around the world, leading to a permanent loss of groundwater storage within an aquifer and even producing structural damage at the Earth’s surface. California’s Tulare Basin is no exception, experiencing about a meter of subsidence between 2015 and 2020. However, understanding the relationship between changes in groundwater volumes and ground deformation has proven difficult. We employ surface displacement measurements from Interferometric Synthetic Aperture Radar (InSAR) and gravimetric estimates of terrestrial water storage from the Gravity Recovery and Climate Experiment (GRACE) satellite pair to characterize the hydrological dynamics within the Tulare basin. The removal of the long-term aquifer compaction from the InSAR time series reveals coherent short-term variations that correlate with hydrological features. For example, in the winter of 2018–2019 uplift is observed at the confluence of several rivers and streams that drain into the southeastern edge of the basin. These observations, combined with estimates of mass changes obtained from the orbiting GRACE satellites, form the basis for imaging the monthly spatial variations in water volumes. This approach facilitates the quick and effective synthesis of InSAR and gravimetric datasets and will aid efforts to improve our understanding and management of groundwater resources around the world.

Donald W. Vasco↗

Terrestrial Analogue Studies from ISRO’s Venus Mission Perspective: Polarimetric Radar Properties of Hawaiian Lava Flows

Detection of present and past volcanism on Venus is one of the major goals of the proposed ISRO’s Venus orbiter mission. The S-band, high-resolution (40 m/pixel) fully Polarimetric Synthetic Aperture Radar (PolSAR) instrument on this mission [1] may have the capabilities to detect volcanism within the mission lifetime using repeated PolSAR imagery, and possibly SAR Interferometry (InSAR, experimental mode). The global mapping efforts of Venus by Magellan mission has enabled comprehensive mapping of lava flows and indicated that Venus has an extensive history of volcanism, the ages of which are largely unknown (e.g. [2]). While Magellan radar emissivity data (e.g. [3, 4]) and Near Infrared emissivity data from VIRTIS [5] suggested the occurrence of recent episodes of volcanic activity (e.g. Maat Mons and Ganis Chasma), as well as the presence of stratigraphically young lava flows (e.g. Idunn Mons), measuring changes in radar backscatter amplitude alone to identify lava flows has many challenges. Although very large changes in the shape of the terrain can be observed in radar backscatter amplitude changes (e.g. [6]), smaller, or relatively flat lava flows are difficult to detect. Previous terrestrial studies suggest that PolSAR and InSAR techniques are very effective for mapping lava flows (e.g. [7-9]), and can be used when changes cannot be distinguished in radar backscatter images. We use the unvegetated lava flows on Hawaiʻi island as a terrestrial analogue to study Venus lava flows for the following reasons: (a) It is extensively studied at several wavelengths commonly used in remote sensing studies (including PolSAR and InSAR methods); and (b) it is a volcanically active area with new lava flows frequently covering older emplaced flows. To investigate the surface roughness, texture, and fine-grained mantling associated with Mauna Loa and Kilauea lava flows, we utilize C- and L-band PolSAR datasets obtained from RISAT-1A (EOS-4) and ALOS PALSAR missions respectively. In particular, we will use the quad-polarized backscatter and polarimetric parameters to characterize the texture of the terrestrial lava flows to understand whether the Venus crust is continuously disrupted during flow emplacement. While some previous studies (e.g. [10, 11]) suggested that surface roughness of most of the Venus flows is comparable to that of terrestrial pāhoehoe flows, other studies indicated that fractal dimensions of some large lava flows on Venus imply high eruption rates which favour the formation of a’a flows (e.g. [12]). We will also analyse the terrestrial flows for the presence/absence of pyroclastic mantling as radar-bright diffuse deposits near the summit regions of some coronae on Venus have been proposed to be young pyroclastics, and possible evidence of a renewed epoch of mantle volcanism that taps into deeper volatiles [13]. A recent study using EOS-4 RISAT-1 data of a part of fresh Mauna Loa lava flows (2022 eruption) emphasizes the ability of fully polarimetric SAR data to understand the diversity of physical properties (e.g. texture and morphology) associated with them (Sreejith et al. 2024); and we will apply similar methods to the PolSAR data obtained from ISRO’s Venus mission for our proposed objectives.

Sriram S Bhiravarasu↗

Time–series Analysis of Volume Change at Brady Hot Springs, Nevada, USA using Geodetic Data from 2003 – 2018

Brady Hot Springs geothermal field has exhibited subsidence, as measured by interferometric synthetic aperture radar (InSAR). Previous studies have examined both the temporal evolution of the deformation from 2004 through 2016 and the spatial extent of the deformation, directly relating the observed subsidence to volumetric changes below the surface. We extend the modeling at Brady to analyze a data set of interferometric pairs spanning from the end of 2003 through 2018. We examine spatial and temporal trends in the observed deformation by time–series analysis of each of the 1656 cubic voxels in a parameterized elastic dislocation model to identify areas where the subsurface volume changes as a function of time. Joint time–series analysis of Global Positioning System and InSAR pairs confirm significant changes in rates of volume change during time intervals when well operations were varied. Here, the rate of subsidence increases with increased injection, consistent with the identification of thermal contraction of the rock matrix as the dominant driving mechanism. Conversely, the modeled volume increases when pumping ceases, suggesting thermal expansion of the rock matrix.

58 GEOSCIENCES↗

Monitoring natural gas storage using Synthetic Aperture Radar: are the residuals informative?

Estimates of line-of-sight (LOS) displacements from Interferometric Synthetic Aperture Radar (InSAR) observations serve as the basis of the long-term monitoring of an operating natural gas storage site at Honor Rancho in California. Here, an inversion algorithm is used to estimate the portion of the signal that is attributable to deformation within the gas storage reservoir, located at a depth of around 3 km. Removing this contribution produces residuals that are used to characterize the background variation is surface deformation at the gas storage facility and to determine a threshold that can signify unusually large residuals. An application to almost 7 yr of InSAR data, from 2011 until 2018, indicates that there are intervals of heightened residuals as well as brief episodes of anomalously large misfits. An examination of the spatial distributions of the individual residual LOS displacements indicates larger displacements in an alluvial valley just south of the reservoir, with rapid spatial variations in sign, indicating a rather shallow origin. Furthermore, the two anomalous events also involve rapid spatial variations in the LOS displacement residuals directly above the storage facility. The results demonstrate that the technique of extracting residuals after removing the reservoir signal is a useful approach, even in the case of this deep reservoir, and is a promising method for long-term monitoring.

03 NATURAL GAS↗