SEARCH · Engineering Papers

Results for “Ignition delay time”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8

All sources NASA NTRS DOE OSTI

DOE OSTI2020

Optical Investigation of Catalyst Heating Operation in a Light-Duty Compression-Ignition Engine

It is well known that cold start engine operation contributes a majority of tail-pipe emissions during a vehicle drive cycle. Aftertreatment catalysts have poor conversion efficiency during this period due to low conversion efficiency at temperatures less than their light-off temperature. A late post injection strategy, with a delayed injection to increase exhaust enthalpy, can help decrease the time required to heat-up the catalyst. However, late injections into conditions with decreasing temperature and density can result in high emissions and combustion instability. In this study a three-injection strategy with a late-post injection was investigated in an optically-accessible engine. For the first two injections (pilot and main) timing and duration were held constant as the post injection timing was swept and duration varied to hold load constant, at a relevant light-load catalyst heating operating condition. Simultaneous double-pass schlieren and OH chemiluminescence data were acquired in an optically-accessible 0.4 L single-cylinder engine to understand spray characteristics and combustion behavior for #2 diesel fuel. Optical images analysis revealed higher liquid penetration and lower vaporization of the liquid fuel jet as post injection is retarded. It is also observed that retarding post injection timing to +25 CAD resulted in lower observed soot concentration in the piston bowl.

99 GENERAL AND MISCELLANEOUS↗

DOE OSTI2024

Investigating the potential of a higher reactivity fuel to achieve faster heat-up of aftertreatment systems

Shortening the aftertreatment system heat-up period will be crucial to meet upcoming emissions regulations, which mandate significant reductions in tail-pipe emissions for on-road heavy-duty vehicles. This work studies the impact of increasing fuel reactivity on the combustion of post injections during the expansion stroke. The work demonstrates an operating strategy using a blend of di-butyl ether (a potential low-carbon biofuel component) and #2 diesel that achieves higher exhaust enthalpy, while maintaining similar engine-out emissions (NOx and combustion efficiency) in comparison to the baseline #2 diesel fuel (cetane number 41). On average, a 12% increase in exhaust enthalpy was observed for the blend (cetane number 60) relative to the baseline fuel. The ability to operate the higher reactivity fuel at a more retarded post-injection timing, where combustion with #2 diesel was found to be more unstable, and less complete was key to achieving higher exhaust enthalpy. However, a small fuel penalty (3%–5%) was also associated with the higher reactivity fuel with this operating strategy. The formation of fuel lean regions, due to the long ignition delays at late injection conditions, was predicted to be the leading contributor to the increased emissions of products of partial combustion. Here, chemical kinetic simulations using surrogates for the fuels used in the experiments, demonstrated the ability of a higher cetane fuel to outperform the baseline fuel under fuel lean conditions with equivalence ratios less than 0.7.

09 BIOMASS FUELS↗

DOE OSTI2021

Spray and combustion characteristics of pure hydrothermal liquefaction biofuel and mixture blends with diesel

Hydrothermal liquefaction (HTL) is the process in which biological compounds can be converted into biocrude diesel; various feedstocks, such as algae and wet biowaste, can be utilized. Almost 20 million dry tons of wet biowaste is deposited in U.S. municipal wastewaters annually. If recovered and converted into biodiesel, it can act as a massive source of renewable energy. Preliminary experiments on a diesel engine show that HTL fuel can achieve similar performance and emission levels to diesel. In order to further understand the influence of the HTL fuel properties, the HTL fuel and blends with diesel are observed in a constant volume chamber. Previously, 10% and 20% of the HTL fuel were blended with diesel by volume and demonstrated properties that roughly matched diesel in terms of combustion. In this study, 50% and 100% HTL fuel blends are tested on the same apparatus. It was discovered that the workability of HTL is almost the same as that of diesel and is less sensitive to ambient temperatures. When the ambient temperature is reduced from 1200 K to 800 K, the change ratio of ignition delay is only 62% of diesel. By analyzing the combustion process, it can be seen that there is no need to make major modifications to the engine control strategy if HTL fuel is applied to diesel engines. Though, under low temperature and low oxygen conditions, the soot luminosity peak of HTL100 is 3.12 times than that of diesel.

09 BIOMASS FUELS↗

DOE OSTI2025

Experimental Investigation of Air-Fuel Equivalence Ratio Effects on Advanced Dual-fuel Diesel/Ammonia Combustion on a Single-Cylinder Medium-Duty Diesel Engine at High Load

Ammonia (NH3) has gathered a lot of interest as a low-lifecycle-carbon fuel in sectors with high weight and distance requirements, such as shipping. The International Maritime Organization (IMO) mandates a 70-80% greenhouse gas (GHG) reduction by 2040, which is only possible with advanced engine technologies and fuels like NH3. Prior research studies at the US Department of Energy’s Oak Ridge National Laboratory have shown strong performance with NH3 under dual-fuel mode using conventional diesel combustion (CDC) manifold air pressure (MAP) settings. Diesel airflow was initially used to simplify retrofitting (no turbocharger modification), which resulted in air-fuel equivalence ratios (λ) greater than 1.5. To characterize potential improvements in dual-fuel NH3 combustion performance at richer in-cylinder conditions, a global λ sweep using a diesel pilot ignition (DPI) strategy with diesel fuel injected near top-dead center (TDC) and a reactivity-controlled compression ignition (RCCI) injection strategy with diesel fuel injected earlier during the compression stroke were compared. The experiments were conducted at 1200 RPM and 12.6 bar (75% load), and λ was varied by decreasing the commanded air flow to the engine at greater than 90% ammonia energy substitution (AES) level. A diesel injection timing sweep was conducted for both the combustion modes at fixed λ, and the timing with the lowest engine-out N2O emissions was identified. The results indicated an optimal balance between CO2, eq and thermal efficiency benefits for both DPI and RCCI injection strategy cases compared to CDC at a λ of 1.4. The indicated N-based emissions exhibited a strong correlation to the ratio of CA5–50 and ignition delay for DPI, but no apparent trend emerged for the RCCI injection strategy at the tested boundary conditions.

Tyrewala, Daanish [ORNL] (ORCID:0000000208599324)↗

DOE OSTI2025

Experimental investigation of air-fuel equivalence ratio effects on advanced dual-fuel ammonia/diesel combustion on a single-cylinder medium-duty diesel engine at high load

Ammonia (NH 3 ) has garnered significant interest as an alternative fuel for meeting international emissions reduction mandates in sectors with high weight and distance requirements, such as shipping. Technical barriers and unanswered questions remain on the combustion strategies that can maximize ammonia utilization and minimize emissions. Prior research studies at the US Department of Energy’s Oak Ridge National Laboratory have shown strong performance with NH 3 under dual-fuel mode using conventional diesel combustion (CDC) manifold air pressure settings. Diesel airflow was initially used to simplify retrofitting (no turbocharger modification), which resulted in air-fuel equivalence ratios (λ) greater than 1.5. To characterize potential improvements in dual-fuel NH 3 combustion performance at richer in-cylinder conditions, a global λ sweep compared the use of early (E-pilot) and late (L-pilot) single diesel injections. The experiments were conducted at 1200 RPM and 12.8 ± 0.2 bar (75 % load), and λ was varied by decreasing the commanded air flow to the engine at greater than 90 % ammonia energy substitution level. A diesel injection timing sweep was conducted for both the injection strategies at fixed λ, and the timing with the lowest engine-out N 2 O emissions was identified. The results indicated an optimal balance between CO 2,eq and thermal efficiency benefits both E-pilot and l-pilot injection strategy cases compared with CDC at a λ of 1.4. In conclusion, the indicated nitrogen-based emissions exhibited a strong correlation to the ratio of CA5–50 and ignition delay for l-pilot, but no apparent trend emerged for the E-pilot injection strategy at the tested boundary conditions.

Ammonia↗

DOE OSTI2022

Silicon alloying enhances fast heating rate combustion of aluminum particles

Alloys and composites of aluminum (Al) have shown promise in regulating and enhancing particle combustion for energy generation applications. Recent work on aluminum-silicon (Al-Si) spherical alloy particles has shown improved combustion at low heating rates through enhanced diffusion accompanying a lower melting temperature. This study extends reactivity analysis to higher heating rates, comparing oxidation of Al-Si with Al. Flame speeds of Al-Si powder mixed with molybdenum trioxide (MoO 3 ) powder (Al-Si+MoO 3 ) exhibited a faster transition to steady propagation relative to Al+MoO 3 . Bomb calorimetry experiments revealed up to 5.8% greater early temperature rise for Al-Si powder. Rapid steady propagation for Al-Si mixture and faster temperature rise for Al-Si particles were attributed to accelerated kinetics evidenced in thermal equilibrium analysis of the mixtures using a differential scanning calorimeter (DSC). Larger DSC exotherms in the early stages of oxidation (i.e., 480–720 °C) correlated with early heat release and promoted steady flame propagation for Al-Si+MoO 3 compared with Al+MoO 3 . Furthermore, in multiple heating rate DSC studies, Al-Si+MoO 3 ignited at a lower heating rate (i.e., 15 ⁰C/min) than Al+MoO 3 (i.e., 20 ⁰C/min). Both mixtures ignited at temperatures less than 625 °C which is above the melting temperature of Al-Si (574 °C) and below Al (659 °C). Thus, alloy particle fuels with enhanced diffusion-controlled kinetics promote steady flame propagation and show promise for energy generation applications. This is especially promising for technologies driven by enhanced condensed phase combustion such as some propellant additives or applications dependent on reliable burn rates such as pyrotechnic time delay formulations and primers.

36 MATERIALS SCIENCE↗

DOE OSTI2026

Influence of Operating Conditions on Ethanol Passive Prechamber Cold-start Operation

Cold-start operation in spark ignition engines is characterized by many drawbacks such as poor fuel vaporization, substantial wall film formation, and weak ignition which can result in unstable combustion and high concentrations of carbon monoxide (CO), nitrogen oxides (NOx), and unburnt hydrocarbons (UHC) prior to catalyst light-off. These challenges are particularly important for ethanol as the fuel’s high latent heat of vaporization and low vapor pressure can hinder reliable ignition during cold-start. In this context, passive prechamber ignition systems offer a viable pathway to improve ignitability by producing hot turbulent jets that can promote combustion in the main chamber. In this study, the influence of operating conditions on jet formation and combustion characteristics in an ethanol-fueled passive prechamber spark ignition engine is investigated. Two intake pressures (40 kPa and 60 kPa) and two engine speeds (450 and 600 rpm) are studied to represent various stages of the cold-start ramp-up. Results indicate that lower intake pressures lead to delayed and asymmetric turbulent jet formation, and lower peak heat release rates. Lower engine speeds, on the other hand, produced higher peak heat release and faster combustion due to greater residence time in the engine. This greater residence time also increases the likelihood of autoignition in the main chamber, potentially promoting quicker heat release for lower engine speeds. These results provide insight into the role of operating conditions on cold-start ramp-up of passive prechamber engines.

Banagiri, Shrikar [ORNL] (ORCID:0000000239745099)↗

DOE OSTI2022

Operability thresholds for thermally damaged EBW detonators

Operability thresholds that differentiate between functional RP-87 exploding bridge wire (EBW) detonators and nonfunctional RP-87 EBW detonators (duds) were determined by measuring the time delay between initiation and early wall movement (function time). The detonators were inserted into an externally heated hollow cylinder of aluminum and fired with current flow from a charged capacitor using an exploding bridge wire (EBW initiated). Functioning detonators responded like unheated pristine detonators when the function time was 4 μs or less. The operability thresholds of the detonators were characterized with a simple decomposition cookoff model calibrated using a modified version of the Sandia Instrumented Thermal Ignition (SITI) experiment. These thresholds are based on the calculated state of the PETN when the detonators fire. The operability threshold is proportional to the positive temperature difference (ΔT) between the maximum temperature within the PETN and the onset of decomposition (~406 K). Furthermore, the temperature difference alone was not sufficient to define the operability threshold. The operability threshold was also proportional to the time that the PETN had been at elevated temperatures. That is, failure was proportional to both temperature and reaction rate. The reacted gas fraction is used in the current work for the reaction correlation. Melting of PETN also had a significant effect on the operability threshold. Detonator failure occurred when the maximum temperature exceeded the nominal melting point of PETN (414 K) for 45±5 s or more.

42 ENGINEERING↗

DOE OSTI2020

Transients using low-high pulsed power in inductively coupled plasmas

Pulsed inductively coupled plasmas (ICPs) are widely deployed in the fabrication of semi-conductor devices. Pulse repetition frequencies (PRFs) of up to tens of kHz are commonly used during plasma etching for the high power densities they generate during the pulse-on period, and for their unique chemistries during the pulse-off period. The use of highly attaching halogen gases produces low electron densities during the pulse-off period, and these low density can result in instabilities, E-H transitions and ignition delays when applying power on the next pulse. To mitigate these possibilities, a low-level power environment could be maintained during “pulse-off” to moderate the minimum plasma density, therefore reducing ignition delays and enhancing plasma stability. In this work, ICPs sustained by 5 kHz pulsed power using Ar/Cl 2 mixtures at 20 mTorr were computationally investigated. For these conditions, the computed electron temperature (T e ) reaches a quasi-steady state during both the high- and low-power excitation. The model predicts that within the electromagnetic skin-depth, T e spikes to a high value during a low-to-high power modulation, and to a low value during a high-to-low power modulation. At the same time, a few cm above the substrate, there is little modulation in T e , as electron power convected from the skin depth disperses in traversing the reactor. Finally, the positive and negative spikes, and convection of transients across the reactors, are functions of power ramping time and gas mixtures.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2021

Entropy generation from hydrodynamic mixing in inertial confinement fusion indirect-drive targets

The increase in entropy from the physical mixing of two adjacent materials in inertial confinement fusion (ICF) implosions and gas-filled hohlraums is analytically assessed. An idealized model of entropy generation from the mixing of identical ideal-gas particles across a material interface in the presence of pressure and temperature gradients is applied. Physically, mix-driven entropy generation refers to the work done by the gases in expanding into a larger common volume from atomic mixing under the condition of no internal energy change, or work needed to restore the initial unmixed state. Furthermore, the effect of a mix-generated entropy increase is analytically shown to lead to less compression of the composite ICF fluid under adiabatic conditions. The amount of entropy generation is estimated to be ~10 J for a Rayleigh–Taylor-induced micrometer-scale annular mixing layer between the solid deuterium–tritium fuel and (undoped) high-density carbon pusher of an imploding capsule at the National Ignition Facility (NIF). This level of entropy generation is consistent with lower-than-expected fuel compressions measured on the NIF [Hurricane et al., Phys. Plasmas 26, 052704 (2019)]. The degree of entropy increase from mixing of high-Z hohlraum wall material and low-Z, moderate- to high-density gas fills is estimated to lead to ~100 kJ of heat generation for NIF-scale experiments [Moody et al., Phys. Plasmas 21, 056317 (2014)]. This value represents a significant fraction of the inferred missing x-ray drive energy based on observed delays in capsule implosion times compared with mainline simulations [Jones et al., Phys. Plasmas 19, 056315 (2012)].

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2022

LES of HCCI combustion of iso-octane/air in a flat-piston rapid compression machine

Homogeneous Charge Compression Ignition (HCCI) engines promise better efficiency and cleaner emissions than conventional piston engines, but can be challenging to control. Rapid compression machines (RCM) provide a simplified configuration for investigating HCCI combustion behavior, which is necessary for effective control of engine ignition timing and peak pressures. Here, in this study, we assess the utility of large eddy simulations (LES) for predicting HCCI combustion in a 3-D configuration. To this end, LES with finite-rate chemistry employing a 99-species iso-octane/air mechanism of two RCM operating conditions are performed. The RCM configuration under consideration was designed by Strozzi et al. with a flat piston to introduce large amounts of thermal stratification representative of realistic HCCI engine conditions, through the generation of corner vortices. It is shown that the simulation provides reasonable agreement with temperature fluctuations (7% difference), as well as ignition delay in the short ignition case (1 ms difference), while the long ignition case (35 ms difference) highlights more substantial deficiencies that are still within the expected uncertainty from the employed chemical mechanism. Flame propagation modes predicted by LES agree with experimental observations: spontaneous ignition is seen in the short ignition case, while deflagration is more prominent in the long ignition case. Analysis of global and local quantities classify the short ignition case in a mixed ignition regime, and the long ignition case in the mild ignition regime. These results demonstrate the utility of FRC-LES for investigations of multimode combustion regimes of HCCI combustion in a 3-D configuration.

33 ADVANCED PROPULSION SYSTEMS↗

DOE OSTI2023

Effects of sub‐mm cylindrical voids on detonation performance in PBX 9501

Abstract Internal features of varying scale and geometry are always present in explosives systems. Below a critical length, dependent on the explosive, these features can operate as a driving force for energy concentration and reaction, known as hotspots. At larger length scales, internal features result in jetting and detonation wave shaping, allowing for bulk work to be done by the explosive as is seen in shape charges. To date, a large volume of work has been performed to simulate hotspot ignition and large‐scale wave shaping. However, little experimental data exists on the effects of features in intermediate length scales, 0.1 to 1 millimeter. It has been observed in many tests that these small‐scale features can influence the high explosive (HE) performance and in some cases cause substantial damage to adjacent systems. This work provides quantitative data on the effects of machined voids moderately above more typical hotspot lengths, 0.3–0.8 mm in diameter, in PBX 9501 pressed to 1.785 g cm −3 ±2.5 mg cm −3 . Streak imaging was used to visualize void collapse, jet velocity, re‐initiation time, and wave shape evolution. Delay in detonation front propagation time was found to be linearly dependent on the void diameter and jet velocity was found to be independent within the tested range and resolution. Cut‐back experiments were used to investigate wave shape distortion and evolution downstream of the void, showing consistent growth and decay shapes across all void sizes. Simulations using CTH, a hydrocode by Sandia National Laboratory, were used to investigate void collapse showing agreement with the trends of experimental results but yielded inaccurate wave shape development delay values. Both simulation and experimental results identified several re‐initiation mechanisms with jetting and subsequent double shocking of localized HE being the dominant mechanisms for the void sizes that were studied.

45 MILITARY TECHNOLOGY, WEAPONRY, AND NATIONAL DEF↗

DOE OSTI2024

An experimental, theoretical, and kinetic modeling study of post-flame oxidation of ammonia

The post -flame oxidation rate of ammonia was investigated in a novel atmospheric pressure flow reactor at temperatures of 1280 ± 16 K and as a function of residence time and mixture composition (1-10% O 2 , dry and moist). The experimental results, as well as selected data from literature, were analyzed using an updated detailed chemical kinetic model. The medium temperature, very lean conditions enhance the importance of reactions of the nitroxyl (HNO) intermediate. High-level theory was used to calculate the rate constant for HNO + NH 2 , indicating that this step is significantly faster than values used in literature. Furthermore, a trajectory based approach was used to determine collision efficiencies for selected bath gases for HNO + M. The experimental results show that the NH 3 oxidation rate increases with temperature and O 2 concentration, while the presence of water vapor slightly inhibits reaction. Formation of NO and N 2 O was strongly promoted at higher levels of O 2 . Modeling results agreed well with the measurements, except at the lowest level of O 2 . The predicted oxidation rate of NH 3 was shown to result from a delicate balance between chain branching and terminating steps involving NH 2 , H 2 NO, and HNO. Recent theoretical work on reactions of these species by Klippenstein and coworkers and Stagni et al. was instrumental in improving modeling predictions. After initiation, NO reached a pseudo -steady-state level, where the pathways to NO were largely balanced by the NH 2 + NO reaction. Nitric oxide was partly oxidized to NO 2 , with the NH 2 + NO 2 reaction responsible for most of the N 2 O formation. Novelty and significance statement: This study provides the first detailed kinetic analysis of the lean postflame oxidation of ammonia, based on time -resolved flow reactor data in a novel reactor. In addition to the post -flame oxidation rate of ammonia, data for formation of NO and N 2 O were compared with modeling predictions. The medium temperature, very lean conditions enhance the importance of reactions of the HNO and H 2 NO intermediates. Inclusion in the model of results from recent high-level theoretical work, including present calculations for HNO + NH 2 and HNO + M, was crucial for capturing the observed behavior. It is argued that the post -initiation steady-state NH 3 oxidation rates constitute important data for model validation, along with ignition delays and laminar flame speeds.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2020

On the Pressure Generated by Thermite Reactions Using Stress-Altered Aluminum Particles

Here we examine pressure build-up and decay in thermites upon impact ignition and interprets reactivity based on the holistic pressure history. The thermite is a mixture of aluminum (Al) combined with bismuth trioxide (Bi 2 O 3 ) powder. Four different Al particles sizes were examined that ranged from 100 nm to 18.5 μm mean diameter and for each size, two different Al powder treatments were examined: stress-altered compared to untreated, as-received Al powder. Stress-altered Al powders have been shown to be more reactive, such that the stress-altered Al powder thermites offer a metric for analyzing thermite reactivity in terms of pressure development compared to untreated Al powder. In a binary thermite system, multiple phase changes and interface chemistry influence the transient pressure response during reaction. Results reveal three key pressure metrics that need consideration specifically for thermite combustion: (1) delay time to peak pressure, (2) peak pressure, and (3) decay after peak pressure. Our experiments show that a lower peak pressure corresponds with higher thermite reactivity because aluminum consumption of oxygen generated by decomposing solid oxidizer reduces the peak pressure. Faster rates of reaction consume oxygen at higher rates such that pressure development becomes more limited than less reactive thermites and the result is a lower peak pressure. This conclusion is opposite of traditional studies using metal fuels with a gaseous environment that typically show higher peak pressures correspond with greater reactivity.

42 ENGINEERING↗

DOE OSTI2025

Design of a High-Pressure Fuel System for Use with Dimethyl Ether

The paper documents the modeling and experimental work on a common rail fuel injection system for Dimethyl Ether, a potential diesel substitute with a low carbon intensity signature. The DME fuel system is deployed on a light duty 2.2L compression ignition engine. The paper describes the injector optimization to shift to higher flows to account for the lower heating value and density of the DME when compared to diesel. The type of the injection system used for the DME application is an advanced rendering of the Common rail noted for a one-piece piston-needle injector construction and a solenoid driven spill valve featuring a pressure balanced poppet. A dedicated high-pressure fuel pump designed to pressurize DME is used. The design results in a fast acting open and close injection event, reduced leakage, with reduced cavitation in the fuel injector volume. Design parameters for system optimization included fill and spill orifices, needle lift, bias spring, and injector hole size. The design model provides good correlation of the instantaneous rates of injection with experiments across a wide range of pressure and injection timings. Proposed performance milestones for the design included similar DME injection duration to the diesel counterpart for same fuel energy injected into the cylinder to retain high engine cycle efficiency. Here, the dedicated DME design provided reduced hydraulic delays of 50%. Tests demonstrated sustained operation at pressures of 1000 bar, with capability to reach 1500bar. Durability tests showed no cavitation-deterioration over a 200-hour test cycle by means of spray imaging and hardware inspection.

De Ojeda, William [WM International Engineering, L↗

DOE OSTI2022

Effects of non-thermal termolecular reactions on detonation development in hydrogen (H 2 )/methane (CH 4 ) - air mixtures

The binary fuel blend of H 2 /CH 4 is one of the most promising hydrogen-enriched hydrocarbon fuels in spark-ignition (SI) engines. Yet, the undesirable phenomenon of super-knock, which can severely and in-stantaneously damage an SI engine, limits its widespread adoption. Moreover, there is still a lack of con-sensus on the precise mechanism by which this phenomenon occurs i.e. via flame acceleration or spon-taneous ignition, despite numerous previous investigations. At the same time, recent studies [M. P. Burke, S. J. Klippenstein, Nat. Chem. 9 (2017) 1078 -1082, Y. Tao, A. W. Jasper, Y. Georgievskii, S. J. Klippenstein, R. Sivaramakrishnan, Proc. Combust. Inst. 38 (2021) 515-522] have demonstrated a high probability of occurrence of non-thermal reactions in premixed flames of such H 2 /CH 4 fuel blends with air due to the presence of non-trivial amounts of highly reactive radicals including H, O and OH apart from O 2 . The present study focuses on the evolution of an initial deflagration front to a detonation wave in H 2 /CH 4 - air mixtures under SI engine relevant conditions through fully resolved, constant volume 1D simulations with and without non-thermal reactivity. Non-thermal reactions were included in the macroscopic kinetics model as chemically termolecular reactions facilitated by the H + CH 3 and H + OH radical-radical recombination and the H + O 2 radical-molecule association reactions. Further, the nonthermal reactions result in a corresponding decrease in the reaction fluxes of the incipient recombination/association reactions. Therefore, an additional set of simulations were performed by applying corrections to the respective incipient recombination/association rate constants using the methodology demonstrated by Tao et al. [Y. Tao, A. W. Jasper, Y. Georgievskii, S. J. Klippenstein, R. Sivaramakrishnan, Proc. Combust. Inst. 38 (2021) 515-522]. Compared to the baseline case, the onset of spontaneous ignition in the end-gas region was observed to be delayed in the presence of non-thermal termolecular reactions. Concurrently, the developing detonation was observed to be significantly stronger. In contrast, applying corrections to the recombi-nation/association rate constants resulted in a completely different behavior. Specifically, detonation was observed to occur due to self acceleration of the primary flame in the absence of spontaneous ignition in the end-gas region. Sensitivity analysis was performed to quantify the effects of non-thermal reactions on the duration of heat release rate and thereby the mechanism of detonation formation. In addition, chemical explosive mode analysis (CEMA) was performed to identify the dominant species/reactions re-sponsible for the observed results.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2020

Verification of diesel spray ignition phenomenon in dual-fuel diesel-piloted premixed natural gas engine

Dual-fuel (DF) engines, in which premixed natural gas and air in an open-type combustion chamber is ignited by diesel-fuel pilot sprays, have been more popular for marine use than pre-chamber spark ignition (PCSI) engines because of their superior durability. However, control of ignition and combustion in DF engines is more difficult than in PCSI engines. In this context, here we focus on the ignition stability of n-heptane pilot-fuel jets injected into a compressed premixed charge of natural gas and air at low-load conditions. To aid understanding of the experimental data, chemical-kinetics simulations were carried out in a simplified engine-environment that provided insight into the chemical effects of methane (CH4) on pilot-fuel ignition. The simulations reveal that CH4 has an effect on both stages of n-heptane autoignition: the small, first-stage, cool-flame-type, low-temperature ignition (LTI) and the larger, second-stage, high-temperature ignition (HTI). As the ratio of pilot-fuel to CH4 entrained into the spray decreases, the initial oxidization of CH4 consumes the OH radicals produced by pilot-fuel decomposition during LTI, thereby inhibiting its progression to HTI. Using imaging diagnostics, the spatial and temporal progression of LTI and HTI in DF combustion are measured in a heavy-duty optical engine, and the imaging data are analyzed to understand the cause of severe fluctuations in ignition timing and combustion completeness at low-load conditions. Images of cool-flame and hydroxyl radical (OH*) chemiluminescence serve as indicators of LTI and HTI, respectively. The cycle-to-cycle and spatial variation in ignition extracted from the imaging data are used as key metrics of comparison. The imaging data indicate that the local concentration of the pilot-fuel and the richness of the surrounding natural-gas air mixture are important for LTI and HTI, but in different ways. In particular, higher injection pressures and shorter injection durations increase the mixing rate, leading to lower concentrations of pilot-fuel more quickly, which can inhibit HTI even as LTI remains relatively robust. Decreasing the injection pressure from 80 MPa to 40 MPa and increasing the injection duration from 500 µs to 760 µs maintained constant pilot-fuel mass, while promoting robust transition from LTI to HTI by effectively slowing the mixing rate. This allows enough residence time for the OH radicals, produced by the two-stage ignition chemistry of the pilot-fuel, to accelerate the transition from LTI to HTI before being consumed by CH4 oxidation. Thus from a practical perspective, for a premixed natural gas fuel–air equivalence-ratio, it is possible to improve the “stability” of the combustion process by solely manipulating the pilot-fuel injection parameters while maintaining constant mass of injected pilot-fuel. This allows for tailoring mixing trajectories to offset changes in fuel ignition chemistry, so as to promote a robust transition from LTI to HTI by changing the balance between the local concentration of the pilot-fuel and richness of the premixed natural gas and air. This could prove to be a valuable tool for combustion design to improve fuel efficiency or reduce noise or perhaps even reduce heat-transfer losses by locating early combustion away from in-cylinder walls.

42 ENGINEERING↗

DOE OSTI2024

Electrical design of the flexible imaging diffraction diagnostic for laser experiments (FIDDLE) at the National Ignition Facility (NIF)—Requirements, design, and performance

The Flexible Imaging Diffraction Diagnostic for Laser Experiments (FIDDLE) is a newly developed diagnostic for imaging time resolved diffraction in experiments at the National Ignition Facility (NIF). It builds on the successes of its predecessor, the Gated Diffraction Development Diagnostic (G3D). The FIDDLE was designed to support eight Daedalus version 2 sensors (six more hCMOS sensors than any other hCMOS-based diagnostic in NIF to date) and an integrated streak camera. We will review the electrical requirements, design, and performance of the electrical subsystems that were created to support this large number of cameras in the FIDDLE. The analysis of the data that the FIDDLE is intended to collect relies heavily on the accurate and well-understood timing of each sensor. We report camera-to-camera timing jitter of less than 100 ps rms and sensor integration times of 2.2 ns FWHM in 2-2 timing mode. Additionally, diffraction experiments on the NIF produce electric fields (EMI) on the order of 1 kV/m, which have been observed to negatively impact the performance of some electrical components of the FIDDLE. We report on the results of testing hCMOS camera electronics in a similar EMI environment generated in an offline lab. In addition, we also summarize the use of a novel approach to using a vector network analyzer as an EMI leak detector to understand and reduce the negative impacts of EMI on the FIDDLE.

47 OTHER INSTRUMENTATION↗