Microstructural stability of a self-ion irradiated lanthana-bearing nanostructured ferritic steel
Not Available
SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Not Available
This study reports on the quantification of deuterium in ion-irradiated gamma-LiAlO2 pellets as a function of dose and temperature. The gamma-LiAlO2 pellets were sequentially irradiated with He+ and D2+ ions to the same fluences of 5E16, 1E17 and 2E17 He++D+/cm2 at 188 K. Additional irradiation was performed to 1E17, 2E17 and 4E17 He++D+/cm2 at 573 K. A set of the pellets irradiated at 188 K was shipped and stored at low temperatures from 80 to 132 K and characterized using time-of-flight secondary ion mass spectrometry at ~173 K. The deuterium depth profiles show a Gaussian-like distribution in the low-temperature pellets. The total deuterium retention is found to be directly proportional to the ion fluence. About 27 at.% of the implanted deuterium atoms were released from the pellet irradiated to 2E17 He++D+/cm2 at 188 K during storage at room temperature for ~1 month. Retention of the trapped or bound deuterium during ion irradiation at 573 K increases initially with ion fluence and tends to saturate at a high fluence. The amount of the released deuterium is observed to be quantitatively consistent with that of the released tritium from similar standard pellets during neutron irradiation at 573 K.
In this work, two tristructural isotropic (TRISO)-coated nuclear fuel particles were examined by electron probe microanalysis (EPMA) as part of the Advanced Gas Reactor program. The compacts’ average irradiation temperatures ranged from approximately 1260 to 1290 °C. One particle was examined in the as-irradiated condition, while the other was subject to 1600 °C post-irradiation safety testing. This study was undertaken to test a newly-developed EPMA technique to determine fission product masses in TRISO particles on a layer-by-layer basis, and to compare fission product distributions between an as-irradiated and safety-tested particle. Fission product concentration profiles were collected along two radii in each particle, with measured concentrations used to compute the fission product mass in each TRISO particle layer. These measured masses were then compared to those predicted from ORIGEN modeling calculations. Data collected from these measurements show that for these two particles, masses determined via EPMA were within ± 20% of the calculated masses for the rare-earth elements, Mo, Zr, Cs, I, and Pd. Elements that tend to be less homogeneously distributed include Sr, Te, Eu, Ag, and possibly Ba. Measured Ag masses differed by more than 40% from the calculated mass. Lanthanides other than Eu remain primarily within the fuel kernel in the as-irradiated particle but in the safety-tested particle these element masses were divided approximately equally between the kernel and kernel periphery. In both particles, the majority of Sr and Eu accumulated in the carbon-rich kernel periphery, although in the safety-tested particle, Sr and Eu accumulated farther from the fuel kernel than occurred with irradiation alone. A greater mass fraction of mobile elements, such as Cs and I accumulated in the buffer and IPyC in the safety-tested particle as compared to the as-irradiated particle. When fully developed and tested, this mass balance approach to TRISO particle analysis has the potential to provide insight into fuel behavior.
A firm understanding of the effect of radiation on materials is required to develop predictive models of materials behavior in-reactor and provide a foundation for creating new, more radiation-tolerant materials. Ion irradiation can serve this purpose for nuclear reactor components and is becoming a key element of materials development for advanced nuclear reactors. Ion irradiations can be conducted quickly, at low cost, and with precise control over irradiation temperature, temperature uniformity, dose rate, dose uniformity and total dose. During proton irradiations the 2{sigma}(twice the standard deviation) of the sample temperature is generally below {approx}7 deg. C, the dose rate variation {approx}3%, the dose uncertainty {approx}3%, and there is an excellent temperature and dose uniformity across the irradiated area. In this article, we describe the experimental setup and irradiation procedure used to conduct well-controlled ion irradiations at the University of Michigan.
In order to examine irradiation performance of the new Tri-structural Isotropic (TRISO) fuel for the High Temperature Gas-cooled Reactor (HTGR) at the burnup around 100 GWd/t, a capsule irradiation test was conducted by WWR-K research reactor in the Institute of Nuclear Physics (INP) of Kazakhstan. The irradiated TRISO fuel was designed by Japan Atomic Energy Agency (JAEA) and fabricated in basis of the HTTR fuel technology in Japan. The fractional release of fission gas from the fuel during the irradiation shows good agreement with the predicted one released from as-fabricated failed TRISO fuel. It was suggested that unexpected additional fuel failure would not occur during the irradiation up to 100 GWd/t. In addition, the post-irradiation examination (PIE) with the irradiated fuel is planned to qualify TRISO fuel integrity and upgrade HTGR fuel design for further burnup extension. (authors)
Unalloyed molybdenum and Oxide Dispersion Strengthened (ODS) molybdenum were irradiated at 300 C and 600 C in the high flux isotope reactor (HFIR) to neutron fluences of 0.2, 2.1, and 24.3 x 10{sup 24} n/m{sup 2} (E > 0.1 MeV), producing damage levels of 0.01, 0.1 and 1.3 Mo-dpa. Hardness measurements, electrical resistivity measurements, tensile testing, and Transmission Electron Microscopy (TEM) were used to assess the defect structure. Irradiation hardening was evident even at a damage level of 0.01 dpa resulting in a significant increase in yield stress, decrease in ductility, and elevation of the Ductile-to-Brittle Transition Temperature (DBTT). The observed size and number density of voids and loops as well as the measured irradiation hardening and electrical resistivity were found to increase sub-linearly with fluence over the range of exposure investigated. This supports the idea that the formation of the extended defects that produce irradiation hardening in molybdenum are the result of a nucleation and growth process rather than the formation of sessile defects directly from the displacement damage cascades. The formation of sessile defect clusters in the displacement cascade would be expected to result in a linear fluence dependence for the number density of defects followed by saturation at fluences less than 1-dpa. This conclusion is supported by Molecular Dynamics (MD) simulations of cascade damage which do not reveal large clusters forming directly as a result of the short-term collapse of the cascade. The finer grain size for the unalloyed Mo and ODS Mo compared to Low Carbon Arc Cast molybdenum results in slightly less irradiation hardening and slightly lower DBTT values. The unalloyed molybdenum used in this work had a low impurity interstitial content that correlates with a slightly lower void size and void number density, less irradiation hardening and lower change in electrical resistivity in this fluence range than is observed for ODS Mo. Although the differences are relatively subtle, this result does suggest that high purity can result in slightly improved resistance to irradiation embrittlement in molybdenum at low fluences.
Not Available
The effect of neutron irradiation on low-temperature deformation of Mo in two heat treatments, i.e. annealed and stress-relieved, was investigated. Specimens were irradiated at reactor coolant temperature ({approx}80 C) to doses ranging from 7.2 x 10{sup -5} to 0.28 dpa in the High Flux Isotope Reactor. Tensile tests were carried out between -50 and 100 C at strain rates of 1 x 10{sup -5}-1 x 10{sup -2} s{sup -1}. Thermal activation analysis based on tensile data was performed to understand the low-temperature deformation mechanism. Irradiation softening and reduced dependence on test temperature and strain rate of the yield stress was observed in the annealed Mo after low-dose neutron irradiation (<{approx}0.003 dpa). Higher dose neutron irradiation caused a thermal hardening only. The stress-relieved Mo showed a weaker dependence on test temperature and strain rate of the yield stress than the annealed Mo, and the dependence of the yield stress of the stress-relieved Mo was nearly unchanged after irradiation. Comparison of the experimental values of activation parameters with the theoretical predictions of dislocation models indicates that the Fleischer model of interactions of dislocations with tetragonal strains gave a better description of the activation process than the double-kink model, which implies a scavenging effect. The reduced test temperature and strain rate dependence following irradiation may be explained by the decreased effective stress due to trapping of interstitial solute species by neutron-produced defects.
We present that incorporating Raman spectroscopy with transverse lift-out specimens is demonstrated to effectively characterize depth-dependent ion-irradiation damage in nuclear ceramics, such as SiC/SiC composites irradiated up to 1, 10 and 50 displacements per atom (dpa) at 350 °C using 10 MeV Au ions. Raman spectroscopy reveals irradiation-induced structural disorder saturation in both SiC-fiber and SiC-matrix at doses as low as 1 dpa, despite vastly different microstructures, inferred from similar longitudinal optical (LO) and transverse optical (TO) phonon peak shifts. Diamond (D) and graphitic (G) peaks from SiC-fibers disappear under irradiation, revealing irradiation-induced carbon packet loss. The irradiation-induced carbon packet loss is also verified by conducting TEM on same FIB foils used for Raman spectroscopy. In a previous study, the irradiation-induced SiC-fiber shrinkage is known to occur due to carbon packet loss in fibers.
Ionization and displacement effects are basic phenomena in damage processes of materials under space-particle irradiation. In this paper, the damage behaviors were investigated on the polyimide under proton irradiation using electron paramagnetic resonance (EPR) spectra analysis and optical absorbance valuation. The results indicate that the proton irradiation induces the formation of pyrolytic carbon free-radical with a g value of 2.0025, and the population of free radicals increases with the irradiation fluence. The most important finding is that the irradiation-induced free-radical population increases linearly with the displacement damage dose, as does the optical degradation, whereas the ionization effect alone, during the irradiation, cannot induce the formation of pyrolytic carbon free radical. Furthermore, during the post storage, after irradiation, the free-radical population decreases following a sum of an exponential and a linear mode with the storage time. It is interesting that, during the post storage, the recovery of the degraded optical absorbance of the polyimide follows a similar mode to that of free radicals, and the characteristic time constant changes with the wavelength of the optical spectra.
Controlling defects in crystalline solids is of technological importance for realizing desirable material properties. Irradiation with energetic particles is useful for designing the spatial distribution and concentration of defects in materials. Here, we performed ion irradiation into hexagonal GaN with the wurtzite structure and demonstrated the spontaneous formation of superlattice-like stacking fault arrays. It was found that the modulation period can be controlled by varying the irradiation conditions and subsequent thermal treatments.
. Irradiation assisted stress corrosion cracking (IASCC) is a known issue in current reactors. In a 60 year lifetime, reactor core internals may experience fluence levels up to 15 dpa for boiling water reactors (BWR) and 100+ dpa for pressurized water reactors (PWR). To support a safe operation of our fleet of reactors and maintain their economic viability it is important to be able to predict any evolution of material behaviors as reactors age and therefore fluence accumulated by reactor core component increases. For PWR reactors, the difficulty to predict high fluence behavior comes from the fact that there is not a consensus of the mechanism of IASCC and that little data is available. It is however possible to use the current state of knowledge on the evolution of irradiated microstructure and on the processes that influences IASCC to emit hypotheses. This report identifies several potential changes in microstructure and proposes to identify their potential impact of IASCC. The susceptibility of a component to high fluence IASCC is considered to not only depends on the intrinsic IASCC susceptibility of the component due to radiation effects on the material but to also be related to the evolution of the loading history of the material and interaction with the environment as total fluence increases. Single variation type experiments are proposed to be performed with materials that are representative of PWR condition and with materials irradiated in other conditions. To address the lack of IASCC propagation and initiation data generated with material irradiated in PWR condition, it is proposed to investigate the effect of spectrum and flux rate on the evolution of microstructure. A long term irradiation, aimed to generate a well-controlled irradiation history on a set on selected materials is also proposed for consideration. For BWR, the study of available data permitted to identify an area of concern for long term performance of component. The efficiency of hydrogen water chemistry mitigation technology may decrease as fluence increases for high-stress intensity factors. This report describes a program plan to determine the efficiency of hydrogen water chemistry as a function of the stress intensity factor applied and fluence. The use of existing, available, materials and the generation of additional materials via irradiation in a research reactor are considered.
Irradiation creep and irradiation swelling are two of the lifetime limiting factors for structural materials in nuclear reactors. These mechanical effects are driven by irradiation defect evolution and the interaction of those defects with dislocations in the microstructure. We present here a coupled cluster dynamics – crystal plasticity approach to model irradiation swelling and creep behavior in 316 SS. The time-dependent evolution of irradiation defects is calculated with a cluster dynamics approach and passed to the crystal plasticity model to compute the dislocation evolution. We show the impact of the irradiation defect evolution on the stress state in the material, which drives inelastic deformation through dislocation motion. The inelastic deformation in the 316 SS is dependent on the dose rate, where the inelastic deformation driven by the early-stage irradiation defect evolution determines the mechanical behavior of the 316 SS.
Tritium release from thermal neutron-irradiated Li{sub 4}SiO{sub 4} is initiated with the annihilation of E'-centers by recovering O' with diffusion of O-. Electron Spin Resonance (ESR) shows that differences in the formation of irradiation damage between 14 MeV and thermal neutrons in Li{sub 4}SiO{sub 4} result in different tritium release behaviors. The kinetics for the annihilation of irradiation defects has been determined. The contribution of elastic collisions by 14 MeV neutrons was much higher than that of thermal neutrons. Isothermal annealing experiments show that annihilation of irradiation defects consisted of two processes: namely, the fast and slow annihilation processes. Their activation energies were determined to be 0.13 and 0.39 eV, respectively. Comparing the experimental results for the thermal and 14 MeV neutron irradiated Li{sub 4}SiO{sub 4} shows that the activation energies of the slow annihilation process were significantly different. These results relate to the density of irradiation defects, which in turn depend on the contribution of the recoil particles produced by nuclear reactions to form irradiation damaged sites. (authors)
In this study, porous silicon was fabricated without any chemical etching by self-ion implantation of crystalline Si performed at high temperature and at high fluences. The irradiated silicon samples, which remained crystalline under high temperature ion irradiation, exhibited an increased porous fraction with increasing sample temperature at a given fluence, up to the maximum tested temperature of 650º C. Extremely high ion fluences of at least 2 x 10¹⁸ ions/cm² were necessary to produce significant void growth. Comparisons between the porous silicon structures and irradiation-induced porous networks in Ge, GaSb, and InSb are made, and differences in the formation conditions for these porous networks are discussed.
Self-ion irradiation is widely used as a method to simulate neutron damage in reactor structural materials. Accelerator-based simulation of void swelling, however, introduces a number of neutron-atypical features which require careful data extraction and in some cases introduction of innovative irradiation techniques to alleviate these issues. We briefly summarize three such atypical features: defect imbalance effects, pulsed beam effects, and carbon contamination. The latter issue has just been recently recognized as being relevant to simulation of void swelling and is discussed here in greater detail. It is shown that carbon ions are entrained in the ion beam by Coulomb force drag and accelerated toward the target surface. Beam-contaminant interactions are modeled using molecular dynamics simulation. By applying a multiple beam deflection technique, carbon and other contaminants can be effectively filtered out, as demonstrated in an irradiation of HT-9 alloy by 3.5 MeV Fe ions.
Here, the irradiation tolerance of SiC/SiC composites was studied using 10 MeV Au ion irradiations at 350 °C, for surface doses between 1 and 50 displacements per atom (dpa). Atomic force microscopy and optical profilometry revealed irradiation-induced axial and radial shrinkage of SiC-fibers. At 50 dpa, net fiber shrinkage reached 2.8 ± 0.3%. We conclude that the primary cause of SiC-fiber shrinkage in SiC/SiC composites is the irradiation-induced loss of pre-existing carbon packets, which had occupied 2–3% fiber volume in unirradiated state. A compelling evidence of the carbon packet loss was revealed using a combination of state-of-art conventional transmission electron microscopy (TEM), high resolution TEM, energy-filtered TEM and electron energy loss spectroscopy. Additionally, the carbon packet volume fraction decreased with increasing dose, reaching near-complete loss after 50 dpa. Carbon packet loss was further confirmed using Raman spectroscopy where the carbon D and G peaks disappeared after irradiation. In contrast, irradiation-induced swelling of 1 ± 0.5% was observed in the matrix after 50 dpa. The study also shows that up to 50 dpa, the multilayer pyrolytic-carbon (PyC) interface in the composite is highly irradiation tolerant as it maintained its morphology, graphitic nature and showed no signs of amorphization. Additionally, Raman spectroscopy revealed a saturation of TEM invisible disorder at 1 dpa for both ultra-fine grains of the fiber and the larger SiC-matrix grains. However, TEM visible extended defect formation such as dislocation loops were only detected in the larger matrix grains, thereby revealing a potential role of grain size on defect accumulation in SiC.