Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “IMPLOSIONS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8

Review of hydro-instability experiments with alternate capsule supports in indirect-drive implosions on the National Ignition Facility

Hydrodynamic instability growth of capsule support membranes (or “tents”) has been recognized as one of the major contributors to the performance degradation in high-compression plastic capsule implosions at the National Ignition Facility (NIF). The capsules were supported by tents because the nominal 10-μm diameter fill tubes were not strong enough to support capsules by themselves in indirect-drive implosions on NIF. After it was recognized that the tents had a significant impact of implosion's stability, new alternative support methods were investigated. While some of these methods completely eliminated tent, other concepts still used tents, but concentrated on mitigating their impact. The tent-less methods included “fishing pole” reinforced fill tubes, cantilevered fill tubes, and thin-wire “tetra cage” supports. In the “fishing pole” concept, a 10-μm fill tube was inserted inside 30-μm fill tube for extra support with the connection point located 300 μm away from the capsule surface. The cantilevered fill tubes were supported by 12-μm thick SiC rods, offset by up to 300 μm from the capsule surfaces. In the “tetra-cage” concept, 2.5-μm thick wires (carbon nanotube yarns) were used to support a capsule. Other concepts used “polar tents” and a “foam-shell” to mitigate the effects of the tents. The “polar tents” had significantly reduced contact area between the tents and the capsule compared to the nominal tents. In the “foam-shell” concept, a 200-μm thick, 30 mg/cc SiO 2 foam layer was used to offset the tents away from the capsule surface in an attempt to mitigate their effects. These concepts were investigated in x-ray radiography experiments and compared with perturbations from standard tent support. The measured perturbations in the “fishing pole,” cantilevered fill tube, and “tetra-cage” concepts compared favorably with (were smaller than) nominal tent perturbations and were recommended for further testing for feasibility in layered DT implosions. The “polar tents” were tested in layered DT implosions with a relatively-stable “high-foot” drive showing an improvement in neutron yield in one experiment compared to companion implosions with nominal tents. Furthermore, this article reviews and summarizes recent experiments on these alternate capsule support concepts. In addition, the concept of magnetic levitation is also discussed.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Using cylindrical implosions to investigate hydrodynamic instabilities in convergent geometry

Hydrodynamic instabilities such as the Rayleigh–Taylor (RT) and Richtmyer–Meshkov instabilities disrupt inertial confinement fusion (ICF) implosions through the growth of 3D perturbations. Growth of these 3D imperfections at the interfaces of an ICF capsule during implosion lead to mixing between materials that is detrimental to performance. These instabilities have been studied extensively in planar geometry, but such experiments lack the effects of convergence in spherical implosions. While several studies have been performed in spherical geometry, these often lack a direct means to measure perturbation growth. Experiments in cylindrical geometry include convergence effects while maintaining direct diagnostic access. Although cylinders have less compression than spheres, they do provide an excellent platform to validate modeling for convergent geometries. The problem with previous cylindrical implosion experiments was that the convergence ratios were limited to ~4. With the National Ignition Facility (NIF), larger cylindrical targets can be driven to convergences of 10–15 while maintaining a large enough final diameter to measure perturbation growth. This paper reviews the design process used to both benchmark radiation hydrodynamics codes and enable 1D post-processed simulations to explore design space to separate compression effects from acceleration/deceleration RT instability. Results from 1D simulations suggest that cylindrical implosions on the NIF can produce high-convergence experiments to validate RT instability growth for ICF implosions.

36 MATERIALS SCIENCE↗

Three-dimensional modeling and hydrodynamic scaling of National Ignition Facility implosions

The goal of an inertially confined, igniting plasma on the National Ignition Facility (NIF) [M. L. Spaeth, Fusion Sci. Technol. 69, 25 (2016)] remains elusive. However, there is a growing understanding of the factors that appear to be limiting current implosion performance. And with this understanding, the question naturally arises: What conditions will ultimately be required to achieve ignition, either by continuing to improve the quality of current implosions, or by hydrodynamically scaling those implosions to larger driver energies on some future facility? Given the complexity of NIF implosions, answering this question must rely heavily on sophisticated numerical simulations. In particular, those simulations must respect the three-dimensionality of real NIF implosions and also resolve the wide range of scales for the many perturbation sources that degrade them. This prospectus article reviews the current state of detailed modeling of NIF implosions, the scaling to ignition from recent experiments that that modeling implies, and areas for future improvements in modeling technique that could increase understanding and further enhance predictive capabilities. Furthermore, given the uncertainties inherent in any extrapolation, particularly for a process as nonlinear as ignition, there will be no definitive answer on the requirements for ignition until it is actually demonstrated experimentally. However, with continuing improvements in modeling technique and a growing experience base from NIF, the requirements for ignition are becoming clearer.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Application of cross-beam energy transfer to control drive symmetry in ICF implosions in low gas fill Hohlraums at the National Ignition Facility

Cross beam energy transfer (CBET), invoked by setting a wavelength difference, Δλ, between inner and outer beam cones, can be used to increase the drive on the waist in indirectly driven inertial confinement fusion experiments at the National Ignition Facility (NIF). Historically, hot spot symmetry control in capsule implosions in high (≥0.9 mg/cm 3 4 He) gas fill Hohlraums was enabled by substantial CBET. However, these implosion designs suffered from inflight symmetry swings, high SRS backscatter on the inner cones, and significant hot electron generation posing a threat to DT fuel preheat. Subsequent experiments in larger, low (≤0.6 mg/cm 3 4 He) gas fill Hohlraums demonstrated round implosions by varying the inner cone fraction throughout the laser drive at Δλ = 0 Å while keeping backscatter and hot electron generation very low. To enable driving larger capsules at a given Hohlraum size, additional tools for implosion symmetry control are required. With this goal in mind, here we present a detailed experimental study of using CBET in low gas fill Hohlraums near NIF's current peak power capability. We find a ~2.5× higher sensitivity of the P 2 Legendre mode with respect to Δλ changes compared to that of high gas fill designs. We attribute this observation to the fact that backscatter remains very low and that CBET remains in a linear regime, as suggested by simulations. As a result, a much smaller Δλ of order 1 Å is sufficient for sustaining implosion symmetry while keeping laser-to- Hohlraum coupling high and hot electron generation very low. While this study used plastic ablator capsules, our findings can be generalized to other ablator materials and, hence, show great promise for using wavelength detuning as a strong lever for implosion symmetry control in future low gas fill designs that require smaller case to capsule ratios in order to increase the energy coupled to the capsule.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Achieving record hot spot energies with large HDC implosions on NIF in HYBRID-E

HYBRID-E is an inertial confinement fusion implosion design that increases energy coupled to the hot spot by increasing the capsule scale in cylindrical hohlraums while operating within the current experimental limits of the National Ignition Facility. HYBRID-E reduces the hohlraum scale at a fixed capsule size compared to previous HYBRID designs, thereby increasing the hohlraum efficiency and energy coupled to the capsule, and uses the cross-beam energy transfer (CBET) to control the implosion symmetry by operating the inner (23° and 30°) and outer (44° and 50°) laser beams at different wavelengths (Δλ> 0). Small case to capsule ratio designs can suffer from insufficient drive at the waist of the hohlraum. We show that only a small amount of wavelength separation between the inner and outer beams (Δλ1-2 Å) is required to control the symmetry in low-gas-filled hohlraums (0.3 mg/cm3 He) with enough drive at the waist of the hohlraum to symmetrically drive capsules 1180 μm in outer radius. This campaign is the first to use the CBET to control the symmetry in 0.3 mg/cm3 He-filled hohlraums, the lowest gas fill density yet fielded with Δλ> 0. We find a stronger sensitivity of hot spot P2 in μm per Angstrom (40–50 μm/Å wavelength separation) than observed in high-gas-filled hohlraums and previous longer pulse designs that used a hohlraum gas fill density of 0.6 mg/cm3. There is currently no indication of transfer roll-off with increasing Δλ, indicating that even longer pulses or larger capsules could be driven using the CBET in cylindrical hohlraums. We show that the radiation flux symmetry is well controlled during the foot of the pulse, and that the entire implosion can be tuned symmetrically in the presence of the CBET in this system, with low levels of laser backscatter out of the hohlraum and low levels of hot electron production from intense laser–plasma interactions. Radiation hydrodynamic simulations can accurately represent the early shock symmetry and be used as a design tool, but cannot predict the late-time radiation flux symmetry during the peak of the pulse, and semi-empirical models are used to design the experiments. Deuterium–tritium (DT)-layered tests of 1100 μm inner radius implosions showed performance close to expectations from simulations at velocities up to ~360 km/s, and record yields at this velocity, when increasing the DT fuel layer thickness to mitigate hydrodynamic mixing of the ablator into the hot spot as a result of defects in the ablator. However, when the implosion velocity was increased, mixing due to these defects impacted performance. The ratio of measured to simulated yield for these experiments was directly correlated with the level of observed mixing. These simulations suggest that reducing the mixing, e.g., by improving the capsule defects, could result in higher performance. In addition, future experiments are planned to reduce the coast time at this scale, delay between the peak compression and the end of the laser, to increase the hot spot convergence and pressure. To reduce the coast time by several hundred ps compared to the 1100 μm inner radius implosions, HYBRID-E has also fielded 1050 μm inner radius capsules, which resulted in higher hot spot pressure and a fusion energy yield of ~170 kJ.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Assessment of dynamic-screw-pinch-driven, current-scaled MagLIF target implosion performance using 3D magnetohydrodynamic simulations

Analytic studies and two-dimensional “clean” radiation-magnetohydrodynamic (rad-MHD) simulations employing dynamical similarity driver-target scaling prescriptions [Ruiz et al., Phys. Plasmas 30, 032708 (2023)] suggest that Magnetized Liner Inertial Fusion (MagLIF) target implosions can scale to > 10 MJ DT fusion yields when peak drive current is increased beyond 60 MA. We present results from three-dimensional (3D) rad-MHD simulations of similarity-scaled MagLIF target implosions at peak drive currents ranging from 15 to 40 MA. Simulations in this study suggest that magneto-Rayleigh–Taylor instability (MRTI) growth and feedthrough to the fuel region are more severe at higher drive current scales, which reduces the fusion yield compared to prior analytic and 2D clean simulation predictions. In contrast to standard MagLIF, simulations of current-scaled MagLIF target implosions driven by a dynamic screw pinch (DSP) demonstrate reduced MRTI feedthrough and greater fuel magnetization, resulting in improved thermonuclear performance and enhanced performance scaling with peak drive current. DSP drive enables additional scaling of the liner mass to increase liner radius but maintain implosion time, resulting in higher implosion velocities at the expense of increased susceptibility to MRTI. We present a current- and mass-scaled simulated DSP-MagLIF target implosion at the ∼ 40 MA peak current level that produces ignition scale performance, demonstrating a burn-averaged Lawson ignition parameter above unity and DT fusion yield above 1 MJ.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Constraining hydrodynamic models of inertial confinement fusion implosions using capsule surrogate experiments

We conduct capsule surrogate experiments at the National Ignition Facility to calibrate radiation hydrodynamic simulations to infer hydrodynamic conditions that are not observable in indirect drive ignition implosions. We tune the simulations by applying laser power and cross beam energy transfer (CBET) saturation multipliers to match the observables from capsule surrogate experiments. Shock timing, velocity, and symmetry are measured in liquid D 2 filled Keyhole capsule surrogate experiments and implosion trajectory, stagnation time, and shape time history are measured in in-flight 2D backlit x-ray radiography experiments (“2DConA”) of D 2 gas filled capsule implosions. Calibrated simulations suggest that the N210808 ignition implosion (fusion target gain = 0.7) had a shell mass remaining at stagnation of less than the nominal %5 (3.8%) and resulted in less confinement. For N221204, the shell was made 5.75 μm thicker to trade implosion velocity for increased confinement and resulted in a target gain = 1.5 with a shell mass remaining of 5.7%. Furthermore, a single adjusted model can reproduce all shock timing data as changes are made to shell thickness (79–85 μm) and laser wavelength separation (1.8–4.0 Å). However, for the 2DConA implosions, a 5% variation in the peak power laser multipliers and a 30% variation in late-time CBET between experiments are needed to match the observed stagnation times, in-flight $P_2$ shape, and hot-spot $P_2$ shape. While progress is being made to improve the models in simulations using focused experiments, capsule surrogate experiments will continue to be needed to optimize future ignition designs.

Lasers↗

Beyond alpha-heating: driving inertially confined fusion implosions toward a burning-plasma state on the National Ignition Facility

Recent progress on indirectly-driven inertial confinement fusion (ICF) work at the National Ignition Facility (NIF) is briefly reviewed. An analytic criteria for an ICF burning plasma is given and compared to recent ICF implosion data from the NIF. Scaling of key hot-spot performance metrics is derived from simple physics considerations, including some speculative impacts of asymmetry on the assembly and disassembly of an ICF implosion. A steepest descent solution for the nonlinear equation for hot-spot pressure at peak compression, with the full effects of alpha-heating, is also given. To test if the scalings derived in this paper have some merit, they are compared to data from a variety of recent implosion campaigns on NIF and good agreement is observed. Given the implications of the scalings and existing data, a strategy for injecting more energy into the hot-spot of NIF indirectly driven ICF implosions is defined and the principles of the strategy is discussed. The importance of implosion velocity, late-time ablation pressure, and implosion scale with good symmetry in obtaining the goal of ~50% more hot-spot energy are highlighted along with the limitations of trying to leverage low fuel-adiabat.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Science of Ignition Workshop, Panel 3 Report: Implosion Hydrodynamics

Using an ablation pressure of ~100 Mbars over a period of ~10 ns, the implosion hydrodynamics of an ICF capsule have always been a balance between obtaining high implosion velocities (> 370 km/s), necessary to create sufficient fuel densification (ρR >1g/cm 2 ) and stagnation pressure (> 400 Gbars), while simultaneously attempting to avoid hydrodynamic instabilities and avoid raising the DT fuel entropy much -- either of which frustrates fuel densification and hot spot creation. Ideally, an ICF implosion should have yield within about 50% of 1D, but present evidence from NIC suggests that is not the case and it is presently difficult to estimate the degree to which irradiation asymmetries or high-mode mix, respectively, are contributing to this behavior. If the NIC implosion can resolve any low-mode implosion hydrodynamics issues, there remains the significant challenge of achieving the needed convergence ratios in excess of 30+ without generating unacceptable mid to high-mode instability growth. Indeed, in the handful of NIC shots where the implosion speed was pushed up above ~300 km/s, and which had less than 8% ablator mass remaining, hot spot ion temperature and yield both dropped significantly, with an increase in x-ray brightness, which is consistent with excessive perturbation growth due to hydrodynamic instabilities.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

The high-foot implosion campaign on the National Ignition Facility

If you could identify only one key skill that a primary or secondary designer should possess, it would be the ability to design an implosion that works reliably and as advertised. Being able to harness an implosion is a key skill because of what an implosion does – an implosion is a “pressure amplifier” that takes absorbed energy and turns that energy, with significant energy loss, into pressure. The pressure generated in implosions is used to compress materials to high densities in the primary designers case, and high densities and temperatures in the secondary designers case. While primary designers and their simulation tools can be tested against experiments at scale fielded at high-explosive facilities around the NNSA complex, secondary designers are much more limited in the experimental facilities that can access relevant conditions (facilities such as Omega at the Laboratory for Laser Energetics, the Z-machine at Sandia National Lab in Albuquerque and the National Ignition Facility at Livermore are more-or-less it). Ignition conditions are the highest-pressure and therefore hardest conditions to access with facility levels of energy, but the struggle to obtain ignition has been an illuminating test of the stockpile stewardship model. If you thought the criteria for ignition is when the fusion energy output from an inertially confined fusion (ICF) implosion exceeds the energy delivered to the target, you’d be wrong. While the above definition is used for milestone tracking purposes, the actually definition of ignition that has been used in fusion research since 1957 is when the power produced by the fusing region exceeds the rate at which energy is lost from the fusing region due to x-ray radiation processes and heat conduction processes. This simple statement about fusion power and rates of energy loss lead to a quantitative criterion for ignition that is known as the “Lawson Criteria.”

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Cryogneic-Target Performance and Implosion Physics Studies on OMEGA

Recent progress in direct-drive cryogenic implosions on the OMEGA Laser Facility [T. R. Boehly et al., Opt. Commun. 133, 495 (1997)] is reviewed. Ignition-relevant areal densities of ~200 mg/cm^2 in cryogenic D2 implosions with peak laser-drive intensities of ~5 x 10^14 W/cm^2 were previously reported [T. C. Sangster et al., Phys. Rev. Lett. 100, 185006 (2008)]. The laser intensity is increased to ~10^15 W/cm^2 to demonstrate ignition-relevant implosion velocities of 3–4 x 10^7 cm/ s, providing an understanding of the relevant target physics. Planar-target acceleration experiments show the importance of the nonlocal electron-thermal-transport effects for modeling the laser drive. Nonlocal and hot-electron preheat is observed to stabilize the Rayleigh–Taylor growth at a peak drive intensity of ~10^15 W/cm^2. The shell preheat caused by hot electrons generated by two-plasmon-decay instability was reduced by using Si-doped ablators. The measured compressibility of planar plastic targets driven with high-compression shaped pulses agrees well with one-dimensional simulations at these intensities. Shock mistiming has contributed to compression degradation of recent cryogenic implosions driven with continuous pulses. Multiple-picket (shock-wave) target designs make it possible for a more robust tuning of the shock-wave arrival times. Cryogenic implosions driven with double-picket pulses demonstrate somewhat improved compression performance at a peak drive intensity of ~10^15 W/cm^2.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Effect of the Initial Load Parameters on the K-shell Output of Al Planar Wire Arrays Operating in the Microsecond Implosion Regime

A set of microsecond implosion experiments was carried on the GIT-12 generator to study the radiative performance of Al planar wire arrays. The load parameters such as a wire diameter, a gap between the wires, the number of wires, and the total planar wire mass and width were varied during the experiments, however the implosion time and the peak implosion current were almost the same for all load configurations. This ensured equal energy deposition to the plasma due to kinetic mechanisms for all load configurations. Two implosion regimes with the implosion times of 1050 ns and 850 ns were investigated. The experimental data on the K-shell radiation yield and power at varying load parameters are presented.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

An initial assessment of three-dimensional polar direct drive capsule asymmetries for implosions at the National Ignition Facility

The National Ignition Facility (NIF) provides a unique opportunity to study implosion physics with nuclear yield. The use of polar direct drive (PDD) [A. M. Cok, R. S. Craxton, and P. W. McKenty, Phys. Plasmas 15, 082705 (2008)] provides a simple platform for the experimental studies without expensive optics upgrades to NIF. To determine the optimum PDD laser pointing geometry on NIF and provide a baseline for validating inertial confinement fusion codes against experiments for symmetric and asymmetric implosions, computer simulations using the 3D radiation-hydrodynamics code hydra[M. M. Marinak, R. E. Tipton, O. L. Landen, T. J. Murphy, P. Amendt, S. W. Haan, S. P. Hatchett, C. J. Keane, R. McEachern, and R. Wallace, Phys. Plasmas 3, 2070 (1996)] were preformed. The upper hemisphere of a DT-filled CH capsule was imploded by 96 NIF beams in a PDD configuration. Asymmetries in both polar and equatorial directions around the capsule were observed, with the former dominating the latter. Analysis of the simulation results indicates that the lack of symmetry in the initial power density profile (during the first 200 ps of the implosion) is a primary cause of late-time asymmetry in the implosion as well as decreased yield. By adjusting the laser pointings, the symmetry and total neutron yield were improved. Simulations with dropped quads (four of the NIF laser system's 192 beamlines) without repointing worsen the overall symmetry by a factor of 10 (with respect to rms radial variation around the capsule) and reduce neutron yield by a factor of 2. Both of these degraded implosion characteristics are restored by azimuthal repointing of the remaining quads.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Numerical investigation on the implosion dynamics of wire-array Z-pinches in (r, {theta}) geometry

The implosion dynamics of wire-array Z-pinches are investigated numerically in 2D (r, {theta}) geometry by using a resistive MHD code. It is assumed that the wires have expanded to plasmas with diameter d{sub 0}, which is used as the initial condition for the consequent implosion process. In fact, the explosion process of individual wires is not included. By changing d{sub 0}, the effects of the wire expansion degree on the implosion dynamics are analyzed. When d{sub 0} is larger, the current density is more concentrated at the outer side of the wires and the fraction of current flow around the wire plasmas is nearly in proportion to d{sub 0}. As a result, the ablation rate of wires is increased and the implosion phase starts earlier. This conclusion agrees with the simulation works of other authors [Chittenden et al., Phys. Plasmas 11(3), 1118 (2004)]. When the array radius and initial wire plasma diameter are fixed, the increase of wire number leads to the azimuthal merge of wires during implosion. When the wires number exceed a critical value, which is related to d{sub 0}, wire plasmas can merge to a continuous shell with an azimuthal perturbation in density, which depends on the initial wires number.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Realization of quasi-spherical implosion using pre-shaped prolate wire arrays with a compression foam target inside

Quasi-spherical (QS) implosion of wire arrays and its impact on the foam target have been studied on the 100 ns 1.5 MA Qiangguang-I facility, which suggests that a high quality impact between the QS implosion and foam target can be achieved by adjusting load's initial shape carefully to match the external magnetic pressure. Implosions of loads with H/d ∼ 1.2 were studied with a self-emission x-ray pinhole image system and a dark field schlieren system. The radially developed spike-like instabilities indicate the spherical convergence of plasma. The observed radiation on the foam target surface suggests satisfying implosion symmetry and wire-foam impact simultaneity. An average implosion speed of 10.5 × 10{sup 6 }cm/s was obtained with an optical streak image system. The derived peak kinetic energy density ∼2.1 kJ/cm is remarkably higher than cylindrical cases, which agree with the expectations.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Approximate models for the ion-kinetic regime in inertial-confinement-fusion capsule implosions

“Reduced” (i.e., simplified or approximate) ion-kinetic (RIK) models in radiation-hydrodynamic simulations permit a useful description of inertial-confinement-fusion (ICF) implosions where kinetic deviations from hydrodynamic behavior are important. For implosions in or near the kinetic regime (i.e., when ion mean free paths are comparable to the capsule size), simulations using a RIK model give a detailed picture of the time- and space-dependent structure of imploding capsules, allow an assessment of the relative importance of various kinetic processes during the implosion, enable explanations of past and current observations, and permit predictions of the results of future experiments. The RIK simulation method described here uses moment-based reduced kinetic models for transport of mass, momentum, and energy by long-mean-free-path ions, a model for the decrease of fusion reactivity owing to the associated modification of the ion distribution function, and a model of hydrodynamic turbulent mixing. The transport models are based on local gradient-diffusion approximations for the transport of moments of the ion distribution functions, with coefficients to impose flux limiting or account for transport modification. After calibration against a reference set of ICF implosions spanning the hydrodynamic-to-kinetic transition, the method has useful, quantifiable predictive ability over a broad range of capsule parameter space. Calibrated RIK simulations show that an important contributor to ion species separation in ICF capsule implosions is the preferential flux of longer-mean-free-path species out of the fuel and into the shell, leaving the fuel relatively enriched in species with shorter mean free paths. Also, the transport of ion thermal energy is enhanced in the kinetic regime, causing the fuel region to have a more uniform, lower ion temperature, extending over a larger volume, than implied by clean simulations. We expect that the success of our simple approach will motivate continued theoretical research into the development of first-principles-based, comprehensive, self-consistent, yet useable models of kinetic multispecies ion behavior in ICF plasmas.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Implosion dynamics and x-ray generation in small-diameter wire-array Z pinches

It is known from experiments that the radiated x-ray energy appears to exceed the calculated implosion kinetic energy and Spitzer resistive heating [C. Deeney et al., Phys. Rev. A 44, 6762 (1991)] but possible mechanisms of the enhanced x-ray production are still being discussed. Enhanced plasma heating in small-diameter wire arrays with decreased calculated kinetic energy was investigated, and a review of experiments with cylindrical arrays of 1-16 mm in diameter on the 1 MA Zebra generator is presented in this paper. The implosion and x-ray generation in cylindrical wire arrays with different diameters were compared to find a transition from a regime where thermalization of the kinetic energy is the prevailing heating mechanism to regimes with other dominant mechanisms of plasma heating. Loads of 3-8 mm in diameter generate the highest x-ray power at the Zebra generator. The x-ray power falls in 1-2 mm loads which can be linked to the lower efficiency of plasma heating with the lack of kinetic energy. The electron temperature and density of the pinches also depend on the array diameter. In small-diameter arrays, 1-3 mm in diameter, ablating plasma accumulates in the inner volume much faster than in loads of 12-16 mm in diameter. Correlated bubblelike implosions were observed with multiframe shadowgraphy. Investigation of energy balance provides evidence for mechanisms of nonkinetic plasma heating in Z pinches. Formation and evolution of bright spots in Z pinches were studied with a time-gated pinhole camera. A comparison of x-ray images with shadowgrams shows that implosion bubbles can initiate bright spots in the pinch. Features of the implosions in small-diameter wire arrays are discussed to identify mechanisms of energy dissipation.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Effect of Strongly Magnetized Electrons and Ions on Heat Flow and Symmetry of Inertial Fusion Implosions

This Letter presents the first observation on how a strong, 500 kG, externally applied B field increases the mode-two asymmetry in shock-heated inertial fusion implosions. Using a direct-drive implosion with polar illumination and imposed field, we observed that magnetization produces a significant increase in the implosion oblateness (a 2.5 × larger P2 amplitude in x-ray self-emission images) compared with reference experiments with identical drive but with no field applied. Here, the implosions produce strongly magnetized electrons (ω e τ e >> 1) and ions (ω i τ i > 1) that, as shown using simulations, restrict the cross field heat flow necessary for lateral distribution of the laser and shock heating from the implosion pole to the waist, causing the enhanced mode-two shape.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗