Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Hydraulic Control”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8

Hydraulic properties of adsorbed water films in unsaturated porous media

Adsorbed water films strongly influence residual water saturations and hydraulic conductivities in porous media at low saturations. Hydraulic properties of adsorbed water films in unsaturated porous media were investigated through combining Langmuir's film model with scaling analysis, without use of any adjustable parameters. Diffuse double layer influences are predicted to be important through the strong dependence of adsorbed water film thickness (f) on matric potential ({Psi}) and ion charge (z). Film thickness, film velocity, and unsaturated hydraulic conductivity are predicted to vary with z{sup -1}, z{sup -2}, and z{sup -3}, respectively. In monodisperse granular media, the characteristic grain size ({lambda}) controls film hydraulics through {lambda}{sup -1} scaling of (1) the perimeter length per unit cross sectional area over which films occur, (2) the critical matric potential ({Psi}{sub c}) below which films control flow, and (3) the magnitude of the unsaturated hydraulic conductivity when {Psi} < {Psi}{sub c}. While it is recognized that finer textured sediments have higher unsaturated hydraulic conductivities than coarser sands at intermediate {Psi}, the {lambda}{sup -1} scaling of hydraulic conductivity predicted here extends this understanding to very low saturations where all pores are drained. Extremely low unsaturated hydraulic conductivities are predicted under adsorbed film-controlled conditions (generally < 0.1 mm y{sup -1}). On flat surfaces, the film hydraulic diffusivity is shown to be constant (invariant with respect to {Psi}).

54 ENVIRONMENTAL SCIENCES↗

Improved aircraft dynamic response and fatigue life during ground operations using an active control landing gear system

A three-degree-of-freedom aircraft landing analysis incorporating a series-hydraulic active control main landing gear has been developed and verified using preliminary experimental data from drop tests of a modified main landing gear from a 2722 kg (6000 lbm) class of airplane. The verified analysis was also employed to predict the landing dynamics of a supersonic research airplane with an active control main landing gear system. The results of this investigation have shown that this type of active gear is feasible and indicate a potential for improving airplane dynamic response and reducing structural fatigue damage during ground operations by approximately 90% relative to that incurred with the passive gear.

Mcgehee, J. R.↗

Servo Controlled Variable Pressure Modification to Space Shuttle Hydraulic Pump

Engineering drawings show modifications made to the constant pressure control of the model AP27V-7 hydraulic pump to an electrically controlled variable pressure setting compensator. A hanger position indicator was included for continuously monitoring hanger angle. A simplex servo driver was furnished for controlling the pressure setting servovalve. Calibration of the rotary variable displacement transducer is described as well as pump performance and response characteristics.

Kouns, H. H.↗

Analysis of the T-97 Space Shuttle Solid Rocket Motor test facility

The history of the analyses for the hydraulic force control systems of the T-97 test facility is presented. Two approaches that were investigated for softening the hydraulic systems for improved performance are presented. A valve modification and inclusion of a proportional-integral controller that finally stabilized the system are described. A simulated test case is shown and compared to actual test data from the QM-7 test. The simulated results are very close to the real results but indicate a slightly higher open-loop gain than for the real system.

Williamson, Marlin J.↗

Natural and Hydraulic Fracture Density Prediction and Identification of Controllers

Discrete Fracture Networks (DFN’s) incorporated into hydraulic fracture modeling and reservoir simulation are typically constructed and calibrated to all available high-quality natural fracture data from image logs and core, which generally results in an extremely limited calibration data set. To extrapolate these data over large areas, more broadly sampled data sets, such as discontinuity-related 3-D seismic attributes are often used. Broad spatial trending methodologies can potentially misrepresent natural fracture systems through over-reliance on seismic attributes that are commonly influenced by noise. The Hydraulic Fracture Test Site (HFTS) provides a rare insight of the subsurface natural fracture network and controlling factors on fracture distribution from a mechanical and lithological standpoint. The physical occurrence of hydraulic fractures and their interaction and relationship to preexisting natural fractures can be predicted using analytical models. Such model outputs can be applied to provide higher confidence when developing DFN’s.

Campbell, Whitney↗

Redundant electronic circuit provides fail-safe control

Circuit using dual control amplifiers and dual position demand potentiometers powered from separate sources is used for reliable hydraulic valve controller that prevents closure of valve when control circuits fail, and maintains valve control to close tolerance for more common modes of controller failure.

Archer, J. W.↗

Control oriented model order reduction for the hydraulic system of an autonomous wheel loader

Control design for an autonomous wheel loader requires a high-fidelity and low-order dynamics model. The objective of order reduction is to decrease the number of states in the model while maintaining performance comparable to the original model. Of all the power components in a wheel loader, the model order reduction for steering and working hydraulic systems is most demanding due to its nonlinear and stiff dynamical nature. This paper describes a physics-inspired model order reduction method that can reduce the model order by close to thirty percent. It is achieved by discarding orders with fast dynamics and consolidating multiple states into less new states. Furthermore, this method can also be extended to other types of off-road vehicles such as excavators, bulldozers, etc. Simulation results demonstrate that the reduced-order model exhibits very similar performance to the full-order model under typical operating conditions of wheel loaders, with an output error of less than six percent.

42 ENGINEERING↗

Application of Koopman operator for model-based control of fracture propagation and proppant transport in hydraulic fracturing operation

This work explores the application of the recently developed Koopman operator approach for model identification and feedback control of a hydraulic fracturing process. Controlling fracture propagation and proppant transport with precision is a challenge due in large part to the difficulty of constructing approximate models that accurately capture the characteristic moving boundary and highly-coupled dynamics exhibited by the process. Koopman operator theory is particularly attractive here as it offers a way to explicitly construct linear representations for even highly nonlinear dynamics. The method is data-driven and relies on lifting the states to an infinite-dimensional space of functions called observables where the dynamics are governed by a linear Koopman operator. Here this work considers two problems: (a) fracture geometry control, and (b) proppant concentration control. In both cases, an approximate linear model of the corresponding dynamics is constructed and used to design a model predictive controller (MPC). The manuscript shows that in the case of highly nonlinear dynamics, as observed in the proppant concentration, use of canonical functions in the observable basis fails. In such cases, a priori system knowledge can be leveraged to choose the required basis. The numerical experiments demonstrate that the Koopman linear model shows excellent agreement with the real system and successfully achieves the desired target values maximizing the oil and gas productivity. Additionally, due to its linear structure, the Koopman models allow convex MPC formulations that avoid any issues associated with nonlinear optimization.

42 ENGINEERING↗

Touchdown: The Development of Propulsion Controlled Aircraft at NASA Dryden

This monograph relates the important history of the Propulsion Controlled Aircraft project at NASA's Dryden Flight Research Center. Spurred by a number of airplane crashes caused by the loss of hydraulic flight controls, a NASA-industry team lead by Frank W. Burcham and C. Gordon Fullerton developed a way to land an aircraft safely using only engine thrust to control the airplane. In spite of initial skepticism, the team discovered that, by manually manipulating an airplane's thrust, there was adequate control for extended up-and-away flight. However, there was not adequate control precision for safe runway landings because of the small control forces, slow response, and difficulty in damping the airplane phugoid and Dutch roll oscillations. The team therefore conceived, developed, and tested the first computerized Propulsion Controlled Aircraft (PCA) system. The PCA system takes pilot commands, uses feedback from airplane measurements, and computes commands for the thrust of each engine, yielding much more precise control. Pitch rate and velocity feedback damp the phugoid oscillation, while yaw rate feedback damps the Dutch roll motion. The team tested the PCA system in simulators and conducted flight research in F-15 and MD-11 airplanes. Later, they developed less sophisticated variants of PCA called PCA Lite and PCA Ultralite to make the system cheaper and therefore more attractive to industry. This monograph tells the PCA story in a non- technical way with emphasis on the human aspects of the engineering and flic,ht-research effort. It thereby supplements the extensive technical literature on PCA and makes the development of this technology accessible to a wide audience.

Tucker, Tom↗

Design and flight test of the Propulsion Controlled Aircraft (PCA) flight control system on the NASA F-15 test aircraft

This report describes the design, development and flight testing of the Propulsion Controlled Aircraft (PCA) flight control system performed at McDonnell Douglas Aerospace (MDA), St. Louis, Missouri and at the NASA Dryden Flight Research Facility, Edwards Air Force Base, California. This research and development program was conducted by MDA and directed by NASA through the Dryden Flight Research Facility for the period beginning January 1991 and ending December 1993. A propulsion steering backup to the aircraft conventional flight control system has been developed and flight demonstrated on a NASA F-15 test aircraft. The Propulsion Controlled Aircraft (PCA) flight system utilizes collective and differential thrust changes to steer an aircraft that experiences partial or complete failure of the hydraulically actuated control surfaces. The PCA flight control research has shown that propulsion steering is a viable backup flight control mode and can assist the pilot in safe landing recovery of a fighter aircraft that has damage to or loss of the flight control surfaces. NASA, USAF and Navy evaluation test pilots stated that the F-15 PCA design provided the control necessary to land the aircraft. Moreover, the feasibility study showed that PCA technology can be directly applied to transport aircraft and provide a major improvement in the survivability of passengers and crew of controls damaged aircraft.

Wells, Edward A.↗

Coordinated joint motion control system with position error correction

Disclosed are an articulated hydraulic machine supporting, control system and control method for same. The articulated hydraulic machine has an end effector for performing useful work. The control system is capable of controlling the end effector for automated movement along a preselected trajectory. The control system has a position error correction system to correct discrepancies between an actual end effector trajectory and a desired end effector trajectory. The correction system can employ one or more absolute position signals provided by one or more acceleration sensors supported by one or more movable machine elements. Good trajectory positioning and repeatability can be obtained. A two-joystick controller system is enabled, which can in some cases facilitate the operator's task and enhance their work quality and productivity.

47 OTHER INSTRUMENTATION↗

Coordinated joint motion control system with position error correction

Disclosed are an articulated hydraulic machine supporting, control system and control method for same. The articulated hydraulic machine has an end effector for performing useful work. The control system is capable of controlling the end effector for automated movement along a preselected trajectory. The control system has a position error correction system to correct discrepancies between an actual end effector trajectory and a desired end effector trajectory. The correction system can employ one or more absolute position signals provided by one or more acceleration sensors supported by one or more movable machine elements. Good trajectory positioning and repeatability can be obtained. A two joystick controller system is enabled, which can in some cases facilitate the operator's task and enhance their work quality and productivity.

42 ENGINEERING↗

Experimental and analytical investigation of active loads control for aircraft landing gear

A series hydraulic, active loads control main landing gear from a light, twin-engine civil aircraft was investigated. Tests included landing impact and traversal of simulated runway roughness. It is shown that the active gear is feasible and very effective in reducing the force transmitted to the airframe. Preliminary validation of a multidegree of freedom active gear flexible airframe takeoff and landing analysis computer program, which may be used as a design tool for active gear systems, is accomplished by comparing experimental and computed data for the passive and active gears.

Morris, D. L.↗

Propulsion Controlled Aircraft design and development

This paper describes the design, development, and ground testing of the propulsion controlled aircraft (PCA) flight control system. A backup flight control system which uses only engine thrust, the PCA system utilizes collective and differential thrust changes to steer an aircraft that experiences partial or complete failure of the hydraulically actuated control surfaces. The objective of the program was to investigate, in flight, the throttles-only control capability of the F-15, using manual control, and also an augmented PCA mode in which computer-controlled thrust was used for flight control. The objective included PCA operation in up-and-away flight and, if performance was adequate, a secondary objective to make actual PCA landings. The PCA design began with a feasibility study which evaluated many control law designs. The study was done using off-line control analysis, simulation, and on-line manned flight simulator tests. Control laws, cockpit displays, and cockpit controls were evaluated by NASA test pilots. A flight test baseline configuration was selected based on projected flight performance, applicability to transport and fighter aircraft, and funding costs. During the PCA software and hardware development, the initial design was updated as data became available from throttle-only flight experiments conducted by NASA on the F-15. This information showed basic airframe characteristics that were not observed in the F-15 flight simulator and resulted in several design changes. After the primary objectives of the PCA flight testing were accomplished, additional PCA modes of operation were developed and implemented. The evolution of the PCA system from the initial feasibility study, control law design, simulation, hardware-in-the-loop tests, pilot-in-the-loop tests, and ground tests is presented.

Wells, Edward A.↗

Intra-Specific Variability in Plant Hydraulic Parameters Inferred From Model Inversion of Sap Flux Data

Understanding plant hydraulic regulation is critical for predicting plant and ecosystem responses to projected increases in drought stress. Plant hydraulic regulation is controlled by observable, diverse plant hydraulic traits that can vary as much across individuals of the same species as they do across different species. Direct measurements of plant hydraulic traits from a range of ecosystems remain limited in comparison to other, more readily measured traits (e.g., specific leaf area). Furthermore, plant hydraulic trait measurements, often made at leaf or branch levels, are not easily scaled to whole-plant values that are typically used to predict plant and ecosystem fluxes. In this study, multiple whole-plant hydraulic parameters are inferred from observations of plant water use (i.e., sap flow), soil properties, and meteorological data. We use a Markov Chain Monte Carlo model inversion approach to obtain the best estimates and uncertainty of plant hydraulic parameters that capture whole-plant effective embolism resistance and stomatal sensitivity to decreasing plant water potential. We then use the inferred values in the model to estimate whole-tree water use and isohydricity. This approach reliably infers whole-plant parameter values with enough specificity to resolve inter- and intra-specific differences, and thus supplements time- and labor-intensive direct measurements of traits.

54 ENVIRONMENTAL SCIENCES↗