SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Dynamic stability and performance of injectors, rocket liners, and supersonic combustors
Model scale effect on inlet temperature rise of VTOL jet configurations
Exhaust gas ingestion suppression model tests for VTOL lift engines, measuring inlet thermal environment
Engineering methods for predicting temperatures and velocities in vicinity of vertical lift engines of jet V/STOL aircraft operating near ground
Jet VTOL fighter-type model inlet-air temperature rise analysis with various exhaust pressure ratios and gas temperatures and surface wind velocities for correlating parameters
Ionized gas galactic cluster stabilization model construction, considering ionizing radiation enhanced cosmic flux and quasar PKS 1116 plus 12 absorption spectrum
Heat-transfer coefficients were obtained on a thrust chamber which simulated the geometry of the NERVA nuclear rocket. The tests were performed with and without peripheral film cooling over a chamber pressure range of 1.05 million to 5.84 million newtons per square meter (153 to 847 psia). With no film cooling, the overall axial variation in the value of the correlation coefficient C of the equation (Stanton)* (Prandtl)* to the 0.7ths power = C(Reynolds)* to the -0.2ths power, where * indicates the reference enthalpy condition, was reduced 66 percent when the local diameter in the Reynolds number was replaced by the axial distance from the injector face. The average peak values of C were reduced 25 percent with 2 and 3.75 percent cooling and 50 percent with 7.5 percent cooling.
Explore the source record for details and available documents.
Heat pipe can reverse itself with gas reservoir acting as evaporator, leading to rapid recovery from liquid in reservoir. Single layer of fine-mesh screen is included inside reservoir to assure uniform liquid distribution over hottest parts of internal surface until liquid is completely removed.
Thermocouple probe incorporates small jet of inert gas to cool thermocouple. To measure gas temperatures, cooling jet is turned off momentarily, allowing thermocouple to heat up to near its melting point, then cooling is reapplied. Heating curve is recorded by high speed digital system. Computing system extrapolates final temperature thermocouple would have attained.
A displacer piston which is driven pneumatically by a high-pressure or low-pressure gas is included in a free-piston regenerative hydraulic engine. Actuation of the displacer piston circulates the working fluid through a heater, a regenerator and a cooler. The present invention includes an inertial mass such as a piston or a hydraulic fluid column to effectively store and supply energy during portions of the cycle. Power is transmitted from the working fluid to a hydraulic fluid across a diaphragm or lightweight piston to achieve a hydraulic power out-put. The displacer piston of the present invention may be driven pneumatically, hydraulically or electromagnetically. In addition, the displacer piston and the inertial mass of the present invention may be positioned on the same side of the diaphragm member or may be separated by the diaphragm member.
The failure of all engines on the Symphonie MV2 satellite is attributed to blockage of the oxidizer branch caused by metal salts precipitating and forming a gel which constricts the narrow passage. Laboratory tests and other simulations conducted to observe the behavior of artificially produced jellies on a vacuum show that a removal or at least a reduction of the blockage in the oxidizer branch is possible by evacuation. The greatest blockage appears to occur in the filter. This fact restricts the capability to perform repairs in orbit because the filter installed ahead of the valve cannot by subjected to a vacuum.
After an introduction on the Stirling engine the external combustion system as well as the general loss division and efficiencies are described. The requirements for the combustion system and different variants of the combustion system are compared and discussed.
Tests were conducted to determine the effects of variable enthalpy levels on CPR-488 foam performance and/or recession. Also to be determined was whether the BX-250 thickness indicator plugs (TIP) concept is feasible for measuring recession rates of CPR-488 foam during external tank flight. The tests determined that the TIP plug idea works. The accuracy of the indicated recession depth is approximately + or - 1.16 in. The BX-250 plugs with TiO2 work better than the regular BX-250 plugs. Also, there is an effect of enthalpy on CPR-488 foam performance.
The application of K5NA over hypolon was investigated. The effects of using K5NA over painted cork surfaces, the effects of weathering on the unpainted K5NA surfaces are determined, and the use of water versus solvent for tooling K5NA in place were compared. It is concluded that: (1) K5NA can be applied to hypalon surfaces; (2) K5NA can be left unpainted; and (3) K5NA can be tested with water or solvent.
The requirements for fundamental experimental studies of the influence of free stream turbulence, pressure gradients and wall cooling are discussed. Under turbine-like free stream conditions, comprehensive tests of transitional boundary layers with laminar, reversing and turbulent flow increments were performed to decouple the effects of the parameters and to determine the effects during mutual interaction.
The Space Shuttle Main Engine (SSME) consists of a large number of critical components each serving a special purpose. Any design change in one of these components not only alters its performance but also the performance of the ones in the upstream and in the downstream. To evaluate the effects of such a design change on the flow fields and on SSME's overall performance a multidomain and multidimensional analytical procedure has been developed and applied here to the series of components on the fuel side of the SSME. The results obtained from the multidomain analysis and their comparison with the single-domain solution when the SSME is operating at Full Power Load indicates that the multidomain model shows greater realism. It is concluded that this modeling technique would assist the designer significantly to achieve still higher performance levels of the SSME.
Explore the source record for details and available documents.