Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “HOLE DISTRIBUTION”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8
All sourcesNASA NTRSDOE OSTI
NASA NTRS1986

Attaching Metal Fasteners to Silica Tiles

Stress distributed so high load borne. Fastener bonded in densified hole or captured in plug of similar refractory material, which in turn bonded in hole in parent tile. Plug or bonding distributes mechanical load from fastener to broad region surrounding fastener, reducing local stress concentration and likelihood of breakage. Bonded-plug method has been successful in attaching mechanical fasteners to porous silica refractory tiles used on outer surface of Space Shuttle orbiter.

Holt, J. W.↗
DOE OSTI2024

Problem with gradual absorption in MSD/MSC calculations

Replacing classical exciton model with the better founded Multistep Direct (MSD) and Multistep Compound (MSC) mechanisms has been impeded by incapability of the latter models to describe central part of the neutron emission spectra at incident neutron energies of about 14 MeV and above. We have ascribed this deficiency to the decrease of absorption to the MSC mechanism resulting from the concept of gradual absorption. We were able to obtain very good reproduction of experimentally measured neutron spectra using MSD/MSC calculations when this option was turned off. Such treatment is, however, at odds with the fundamental distinction between MSD and MSC mechanisms that should proceed through the chain of open (P-space) and closed (Q-space) configurations respectively. By blocking gradual absorption we allow the first stage of MSC to be fully populated from the incident channel that at higher incident energies is impossible. We discuss various attempts of addressing the problem that, so far, remains open. In addition, we present an evidence for much tighter spin distribution of particle-hole states than normally assumed.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗
DOE OSTI2021

Finite Element Analysis (FEA) for Water-Foam Fracturing of Granite Rock

In addition to the foam data that were obtained from literature and that were collected from the current study, simulation data was also generated from finite element analysis (FEA) conducted in this study using COMSOL Multiphysics software. The FEA models were built to simulate the experiments conducted at Oak Ridge National Laboratory (ORNL) on cement and granite samples. In these FEA models, temperature was kept at ambient while the pressure profile resembled the loading conditions during the ORNL experiments, where pressure was either monotonically increased or applied cyclically. The cement material was used as a model material and was used to study Von Mises stress and tensile stress distribution for different bore hole length geometry using a parametric sweep with water as fracturing fluid using solid-fluid interaction module. For the granite material, FEA models were developed for stress analysis of cylindrical samples with water or foam fluids. The solid mechanics module in COMSOL was implemented to solve for Von Mises stress and tensile stress. The fluid-structure interaction module was implemented to solve for water-foam interaction on granite cylinder with addition of fluid-loading on structure, i.e., large deformation in solid mechanics with no impact on fluid deformation. Foam was considered as a pseudo single-phase compressible fluid for which material properties were calculated from water and gas (nitrogen) phases. The density of foam is calculated as a function of the densities of water and nitrogen, while viscosity is a function of temperature. Four types of FEA analyses were modelled: 1. Monotonic injection with water 2. Monotonic injection with foam 3. Cyclic injection with water 4. Cyclic injection with foam All the COMSOL files are converted to a zip file which is save in .mph.

15 GEOTHERMAL ENERGY↗
DOE OSTI2024

Problem with gradual absorption in MSD/MSC calculations

Replacing classical exciton model with the better founded Multi-step Direct (MSD) and Multistep Compound (MSC) mechanisms has been impeded by incapability of the latter models to describe central part of the neutron emission spectra at incident neutron energies of about 14 MeV and above. We have ascribed this deficiency to the decrease of absorption to the MSC mechanism resulting from the concept of gradual absorption. We were able to obtain very good reproduction of experimentally measured neutron spectra using MSD/MSC calculations when this option was turned off. Such treatment is, however, at odds with the fundamental distinction between MSD and MSC mechanisms that should proceed through the chain of open (P-space) and closed (Q-space) configurations respectively. By blocking gradual absorption we allow the first stage of MSC to be fully populated from the incident channel that at higher incident energies is impossible. We discuss various attempts of addressing the problem that, so far, remains open. In addition, we present an evidence for much tighter spin distribution of particle-hole states than normally assumed.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
NASA NTRS1977

Far-infrared emission from compact sources in NGC 2264 and the Rosette Nebula

The paper reports the discovery of far-IR emission at 53, 100, and 175 microns from two sources (one in NGC 2264 and another near the Rosette Nebula) associated with molecular clouds but not with any detectable radio continuum emission. The maximum source diameters are estimated to be 20 arcsec, and the spectra of both objects are shown to be broader than that of a 'typical' H II region. It is found that both objects are unresolved at all the IR wavelengths observed, have relatively wide IR spectra, are located at or near the apices of fan-shaped cometary nebulae, have colors between 50 and 200 microns that are among the coolest of any observed far-IR sources, and have luminosities that are an order of magnitude less than the weakest sources observed near compact H II regions. A cylindrically symmetric source model is considered in which a 'hole' in the dust distribution around the central source provides the visible luminosity of the nearby nebula and the dust temperature decreases rapidly with distance. It is suggested that the central sources are probably pre-main-sequence stellar objects with masses of 5 to 10 solar masses and luminosities of a few thousand suns.

Harvey, P. M.↗
NASA NTRS1990

Luminosity-velocity diagrams for Virgo Cluster spirals. I - Inner rotation curves

Optical rotation curves are presented for the innermost portions of nine spiral galaxies in the Virgo Cluster. The emission-line (H-alpha and forbidden N II) velocity data are to be used in combination with new CCD photometry to construct luminosity-velocity diagrams, in a continuing investigation of an apparent initial linear branch and its potential as a distance indicator. Compared to recent H I data, the present optical rotation curves generally show systematically steeper inner gradients. This effect is ascribed to the poorer resolution of the H I data and/or to holes in the gas distribution.

Woods, David↗
NASA NTRS1990

Improved high power/high frequency inductor

A toroidal core is mounted on an alignment disc having uniformly distributed circumferential notches or holes therein. Wire is then wound about the toroidal core in a uniform pattern defined by the notches or holes. Prior to winding, the wire may be placed within shrink tubing. The shrink tubing is then wound about the alignment disc and core and then heat-shrunk to positively retain the wire in the uniform position on the toroidal core.

Mclyman, W. T.↗
NASA NTRS1995

Acceleration phenomena of high-speed wind observed at 0.1-0.3 AU with interplanetary scintillation

The radial distance dependence of solar wind speeds, which were measured by interplanetary scintillation method, has been studied especially for a high-speed solar wind, and large increase of the IPS speeds (300 km/s) was observed at the distance range of 0.1 - 0.3 AU. When the streams are mapped back onto the source surface, they distribute in polar coronal holes or their boundaries. Since the IPS measurement can be biased by several effects such as of line-of-sight integration, strong scattering and random velocities, we examined these biasing effects and have found difficulty to explain the large IPS speed increase with the biasing effects.

Kojima, M.↗
NASA NTRS2019

STROBE-X: X-ray Timing & Spectroscopy on Dynamical Timescales from Milliseconds to Years

We describe a probe-class mission concept that provides an unprecedented view of the X-ray sky, performing timing and 0.2-30 keV spectroscopy over timescales from microseconds to years. The Spectroscopic Time-Resolving Observatory for Broadband Energy X-rays (STROBE-X) has three key science drivers: (1) measuring the spin distribution of accreting black holes, (2) understanding the equation of state of dense matter, and (3) exploring the properties of the precursors and electromagnetic counterparts of gravitational wave sources. To perform these science investigations, STROBE-X comprises three primary instruments. The first uses an array of lightweight optics (3-m focal length) that concentrate incident photons onto solid state detectors with CCD-level (85-130 eV) energy resolution, 100 ns time resolution, and low background rates to cover the 0.2-12 keV band. This technology is scaled up from NICER, with enhanced optics to take advantage of the longer focal length of STROBE-X. The second uses large-area collimated silicon drift detectors, developed for ESA's LOFT, to cover the 2-30 keV band. These two instruments each provide an order of magnitude improvement in effective area compared with its predecessor (NICER and RXTE, respectively). Finally, a sensitive sky monitor triggers pointed observations, provides high duty cycle, high time resolution, high spectral resolution monitoring of the X-ray sky with ~20 times the sensitivity of the RXTE ASM, and enables multi-wavelength and multi-messenger studies on a continuous, rather than scanning basis. The STROBE-X mission concept is a rapidly repointable observatory in low-Earth orbit, similar to RXTE or Swift, and will be presented to the 2020 Astrophysics Decadal Survey for consideration as a probe-class mission.

STROBE-X: X-ray↗
DOE OSTI2023

Population of Merging Compact Binaries Inferred Using Gravitational Waves through GWTC-3

We report on the population properties of compact binary mergers inferred from gravitational-wave observations of these systems during the first three LIGO-Virgo observing runs. The Gravitational-Wave Transient Catalog 3 (GWTC-3) contains signals consistent with three classes of binary mergers: binary black hole, binary neutron star, and neutron star–black hole mergers. We infer the binary neutron star merger rate to be between 10 and 1700 Gpc − 3 yr − 1 and the neutron star–black hole merger rate to be between 7.8 and 140 Gpc − 3 yr − 1 , assuming a constant rate density in the comoving frame and taking the union of 90% credible intervals for methods used in this work. We infer the binary black hole merger rate, allowing for evolution with redshift, to be between 17.9 and 44 Gpc − 3 yr − 1 at a fiducial redshift ( z = 0.2 ). The rate of binary black hole mergers is observed to increase with redshift at a rate proportional to ( 1 + z ) κ with κ = 2. 9 − 1.8 + 1.7 for z ≲ 1 . Using both binary neutron star and neutron star–black hole binaries, we obtain a broad, relatively flat neutron star mass distribution extending from 1.2 − 0.2 + 0.1 to 2.0 − 0.3 + 0.3 M ⊙ . We confidently determine that the merger rate as a function of mass sharply declines after the expected maximum neutron star mass, but cannot yet confirm or rule out the existence of a lower mass gap between neutron stars and black holes. We also find the binary black hole mass distribution has localized over- and underdensities relative to a power-law distribution, with peaks emerging at chirp masses of 8.3 − 0.5 + 0.3 and 27.9 − 1.8 + 1.9 M ⊙ . While we continue to find that the mass distribution of a binary’s more massive component strongly decreases as a function of primary mass, we observe no evidence of a strongly suppressed merger rate above approximately 60 M ⊙ , which would indicate the presence of a upper mass gap. Observed black hole spins are small, with half of spin magnitudes below χ i ≈ 0.25 . While the majority of spins are preferentially aligned with the orbital angular momentum, we infer evidence of antialigned spins among the binary population. We observe an increase in spin magnitude for systems with more unequal-mass ratio. We also observe evidence of misalignment of spins relative to the orbital angular momentum. Published by the American Physical Society 2023

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2024

Magnetic Field Sensing via Multi-Material Acoustic Sensing Optical Fibers with Magnetostrictive Cladding Inclusions

In this conducted research, optical fiber sensors are used to measure low strength alternating magnetic fields. Various fiber sensor configurations are tested and investigated to demonstrate sensing capabilities at different field magnitudes and frequencies. Distributed acoustic sensing fibers (DAS) have been largely studied and documented across a variety of applications and sensing systems. This research uses the DAS technology in tandem with magnetostrictive materials to create a distributed multi-material optical fiber magnetic sensor. Magnetic sensing has high demand across different fields and often runs into challenges of extreme environments including high temperature, corrosion, and areas with poor accessibility. The robust and distributed nature of optical fiber sensors which can be cheaply produced for long lengths is an attractive option over other single point magnetic sensors. In down hole applications specifically, having a distributed sensor able to be deployed easily and over long distances for magnetic sensing would be a large improvement to bulkier traditional magnetometers. In the conducted study, different magnetostrictive materials are implemented in distributed optical fiber sensors to analyze and compare the effective sensitivity and potential commercial viability. Nickel, galfenol alloy, and MetGlas alloy inclusions are drawn into fused silica optical fibers with Bragg gratings inscribed later on for DAS capability. Each was investigated for its response to varying AC magnetic fields to determine relative sensitivity and resolution for distributed magnetic field sensing.

Dejneka, Zach↗
NASA NTRS1994

Ulysses field and plasma observations of magnetic holes in the solar wind and their relation to mirror-mode structures

The term 'magnetic hole' has been used to denote isolated intervals when the magnitude of the interplanetary magnetic field drops to a few tenths, or less, of its ambient value for a time that corresponds to a linear dimension of tens to a few hundreds of proton gyro-radii. Data obtained by the Ulysses magnetometer and solar wind anlayzer have been combined to study the properties of such magnetic holes in the solar wind between 1 AU and 5.4 AU and to 23 deg south latitude. In order to avoid confusion with decreases in field strength at interplanetary discontinuities, the study has focused on linear holes across which the field direction changed by less than 5 deg. The holes occurred preferentially, but not without exception, in the interaction regions on the leading edges of high-speed solar wind streams. Although the plasma surrounding the holes was generally stable against the mirror instability, there are indications that the holes may have been remnants of mirror-mode structures created upstream of the points of observation. Those indications include the following: (1) For the few holes for which proton of alpha-particle pressure could be measured inside the hole, the ion thermal pressure was always greater than in the plasma adjacent to the holes. (2) The plasma surrounding many of the holes was marginally stable for the mirror mode, while the plasma environment of all holes was significantly closer to mirror instability than was the average solar wind. (3) The plasma containing trains of closely spaced holes was closer to mirror instability than was the plasma containing isolated holes. (4) The near-hole plasma had much higher ion beta (ratio of thermal to magnetic pressure) than did the average solar wind. (5) Near the holes, T(sub perp)/T(sub parallel) tended to be either greater than 1 or larger than in the average wind. (6) The proton and alpha-particle distribution functions measured inside the holes occasionally exhibited the flattened phase-space-density contoures in nu(sub perp)/nu(sub parallel) space found in some numerical simulations of the mirror instability.

Winterhalter, Daniel↗
NASA NTRS2020

What Could Be the Observational Signature of Dark Matter in Globular Clusters?

Here we investigate the possibility that some globular clusters (GCs) harbor intermediate mass black holes (BH) in their centers and are also embedded in a low-mass dark matter (DM) halo. Up to date, there is no evidence on whether or not GCs have DM in their constitution. For standard cold DM cosmology, it is expected that GCs form with their own DM halos. Other studies investigate the possibility that GCs were initially embedded in massive DM halos that evolved during the cluster lifetime. An additional intriguing question is related to the existence of intermediate mass black holes (IMBH) in the GCs. The determination of whether GCs hold IMBHs would be able to answer important questions about GCs formation and the circumstances that gave rise to the IMBHs. DM & IMBH in the context of GCs are interesting subjects to be studied and we will perform such studies here, assuming the coexistence of both of them in some GCs. Having such information, we perform the study possible DM signals from GCs. One important subject to be studied is the DM density profile. In the inner regions of GCs, the DM density profile is still an open question of fundamental importance to DM studies, specially for the study of radio and γ-ray emission from DM annihilation in such regions. Here we consider the case of IMBHs in the inner regions of three GCs: 47 Tuc, NGC 6266 and ω Cen. The existence of a black hole (BH) directly affects the matter distribution in its vicinity. These effects are significant for IMBHs as well as supermassive black holes (SMBHs) and can lead to large DM overdensities called spikes. In this paper, we direct our studies to the radio synchrotron emission from DM annihilation with spike profiles around possible IMBHs in GCs. We present our results for synchrotron emission produced by DM annihilation via bbar b channel. We use the best-fit DM mass of 34 GeV and annihilation channel in bbar b used to explain the Galactic center "excess" and perform our analysis for the estimated radio flux. We direct our attention specially to the γ-ray emission from 47 Tuc. When considering a scenario wich includes a BH and the combined analysis of multi-wavelength studies, we conclude that some parameter choice as the annihilation cross section ⟨σ v⟩ used to fit the γ-ray excess differs by many orders of magnitude from the one necessary to fit the radio observations for this globular cluster if we consider the BH scenario.

Elaine C F S Fortes↗
NASA NTRS1985

Use of optimum stiffness tailoring to improve the compressive strength of composite plates with holes

A structural optimization procedure is used to tailor the cross-sectional stiffness distribution of compression-loaded composite plates with holes. Minimum mass designs are obtained for plates with cross sections consisting of two different balanced symmetric laminates with 0 deg, + or - 45 deg and 90 deg plies. The plate interior region contains the hole and is designed from a softer material system with a higher failure strain than the plate exterior region. All-graphite-epoxy plates and hybrid graphite/glass-epoxy plates were studied. Other designs with different percentages of 0 deg and + or 45 deg plies in the exterior laminate are compared with the optimum designs. Designs with uniform cross-sectional stiffnesses also are compared with the tailored cross-sectional stiffness designs. Specimens of each design were tested to verify the analytical predictions. The results show that cross-sectional stiffness tailoring can increase the compressive strength and decrease the mass of compression-loaded laminated plates with holes.

Haftka, R. T.↗
NASA NTRS2000

Bolted Double-Lap Composite Joints Under Mechanical and Thermal Loading

This study concerns the determination of the contact stresses and contact region around bolt holes and the bolt load distribution in single- and double-lap joints of composite laminates with arbitrarily located bolts under general mechanical loading conditions and uniform temperature change. The unknown contact stress distribution and contact region between the bolt and laminates and the interaction among the bolts require the bolt load distribution, as well as the contact stresses, to be as part of the solution. The present method is based on the complex potential theory and the variational formulation in order to account for bolt stiffness, bolt-hole clearance, and finite geometry of the composite laminates.

Kradinov, V.↗
DOE OSTI2024

Ultrawide bandgap semiconductor heterojunction p–n diodes with distributed polarization-doped p-type AlGaN layers on bulk AlN substrates

Ultrawide bandgap heterojunction p–n diodes with polarization-induced AlGaN p-type layers are demonstrated using plasma-assisted molecular beam epitaxy on bulk AlN substrates. Current–voltage characteristics show a turn-on voltage of Vbi≈5.5 V, a minimum room temperature ideality factor of η≈1.63, and more than 12 orders of current modulation at room temperature. A stable current operation of the ultrawide bandgap semiconductor diode is measured up to a temperature of 300 °C. The one-sided n+–p heterojunction diode design enables a direct measurement of the spatial distribution of polarization-induced mobile hole density in the graded AlGaN layer from the capacitance–voltage profile. The measured average mobile hole density is p∼5.7×1017 cm−3, in close agreement with what is theoretically expected from distributed polarization doping. Light emission peaked at 260 nm (4.78 eV) observed in electroluminescence corresponds to interband radiative recombination in the n+ AlGaN layer. A much weaker deep-level emission band observed at 3.4 eV is attributed to cation-vacancy and silicon complexes in the heavily Si-doped AlGaN layer. These results demonstrate that distributed polarization doping enables ultrawide bandgap semiconductor heterojunction p–n diodes that have wide applications ranging from power electronics to deep-ultraviolet photonics. These devices can operate at high temperatures and in harsh environments.

Physics↗
NASA NTRS1977

Stress-intensity factors for cracks emanating from the loaded fastener hole

Using a series approach and the Muskhelishvili formulation in the two-dimensional theory of elasticity, stress-intensity factors K are derived for problems in which cracks emanate radially from the boundary of an arbitrarily loaded internal circular hole in an infinite plate. Numerical values are obtained for K(I) and K(II) for radial cracks from a hole containing a loose-fitted pin or rivet that is pulled perpendicular to the crack direction in the plane of the plate. The method is a general one for determining K for a set of symmetrically emanating radial cracks for a variety of concentrated or distributed tractions on the circular hole.

Shivakumar, V.↗