SEARCH · Engineering Papers

Results for “Graphite/Epoxy”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8

All sources NASA NTRS DOE OSTI

NASA NTRS1986

Impact resistance and interlaminar fracture toughness of through-the-thickness reinforced graphite/epoxy

Five through-the-thickness stitch configurations are analyzed to determine the effect of impact resistance and interlaminar fracture toughness on T3000/3501-6 graphite/epoxy. The test specimens were stitched with either polyester or Kevlar yarns and with various stitch parameters. Tension and compression mechanical, impact and compression-after-impact, and double cantilever beam tests were conducted. It is observed that the stitched laminates have tension and compression strengths 20-25 percent lower than the strengths of unstitched laminates, the tension strength of stitched laminates is reduced with increasing number of stitches, and the compression strength increases as the number of stitches are increased. The impact data reveal that the Kevlar stitched laminates have less damage than unstitched laminates; the most effective configuration for suppressing impact damage and improving interlaminar fracture toughness consists of Kevlar yarns 1/4 inch apart with eight stitches per inch. The mode 1 critical strain energy release rate for the 1/4 inch Kevlar eight stitch laminate was calculated as 30 times higher than that of the unstitched.

Dexter, H. B.↗

NASA NTRS1986

Dynamic delamination crack propagation in a graphite/epoxy laminate

The dynamic delamination crack propagation behavior during ballistic tests of (90/0)5s T-300/934 graphite/epoxy laminates with embedded interfacial cracks was investigated using high speed photography. The impact on the beam-like specimen was produced with a silicon rubber ball, and the crack propagation speeds and the threshold impact velocities required to initiate dynamic crack propagation were determined for several crack positions. The results suggest that the mode of crack propagation depends on the specimen geometry as well as the loading condition. A simplified finite element analysis of the experimental data obtained from one of the midplane-cracked specimens was used to estimate the critical strain energy release rate, which may determine the onset of unstable crack propagation.

Sun, C. T.↗

NASA NTRS1986

Mode II interlaminar fracture of graphite/epoxy and graphite/PEEK

The end notched flexure (ENF) specimen is employed in an investigation of the interlaminar fracture toughness in Mode II (skew symmetric shear) loading of unidirectional graphite/epoxy and graphite/PEEK composites. Important experimental parameters such as the influence of precracking and the data reduction scheme for the Mode II toughness are discussed. Nonlinear load-deflection response is significant for the tough thermoplastic resin composite but is also present for the brittle thermoset composite. The observed nonlinearities, which are highly rate dependent, are attributed to a combination of slow stable crack growth preceding unstable crack growth and material inelastic behavior in the process zone around the crack tip.

Carlsson, L. A.↗

NASA NTRS1987

Metal-Clad Graphite/Epoxy Tubes

Structural parts feature low weight, low thermal expansion, and high stiffness. Unique, non-labor-intensive manufacturing process developed for fabricating aluminum-clad graphite/epoxy (Gr/E) struts which meet Space Station requirements. Method of manufacturing struts provides procedure for using Gr/E material system in very efficient manner. Technique places all fibers in longitudinal direction for stiffness and strength. Aluminum surfaces provide transverse strength and resistance to atomic oxygen in environment.

Bush, Harold G.↗

NASA NTRS1987

Drilling Holes in Graphite/Epoxy

Relatively long-lived bit produces high-quality holes. Effective combination of cutting-tool design, feed, and speed determined for drilling 3/16-and-1/4-in. (0.48-and 0.65-cm) diameter holes in 0.18 in. (0.46cm) thick GM3013A or equivalent graphite/epoxy corrugated spar without backup material and without coolant. Developed to produce holes in blind areas, optimal techniques yielded holes of high quality, with minimal or acceptable delamination and/or fiber extension on drill-exit side.

Minlionica, Ronald↗

NASA NTRS1987

Strength of a thick graphite/epoxy rocket motor case after impact by a blunt object

The National Aeronautics and Space Administration is developing graphite/epoxy filament-wound cases (FWC) for the solid rocket motors of the Space Shuttle. The membrane region is about 36 mm thick. A study was made to determine the reduction in strength of the FWC due to accidental damage caused by low-velocity impacts. Two 76.2 cm diameter by 30.5 cm long cylinders were impacted every 5 cm of circumference with 1.27 cm radius impacters of various mass. The impacters represented tools and equipment dropped from various heights. One cylinder was empty and the other was filled with inert propellant. Five cm wide test specimens were cut from the cylinder. Each was centered on an impact sight. The specimens were X-rayed and loaded to failure in uniaxial tension. The strengths and depths of impact damage were analyzed in terms of maximum impact force. Rigid body mechanics and the Hertz law were used to derive an equation for impact force in terms of kinetic energy and the masses of the impacter and target. The depth of damage was predicted in terms of impact force using Love's solution of pressure applied on part of the boundary of a semi-infinite body.

Poe, C. C., Jr.↗

NASA NTRS1986

Correlation of the deply technique with the ultrasonic imaging of impact damage in graphite/epoxy composites

A quantitative ultrasonic technique for the nondestructive assessment of impact damage is described. The method, which involves digitizing the entire backscattered ultrasonic wave from a sample, was applied to two test panels removed from a 16-ply graphite/epoxy laminate and impacted with an aluminum ball fired at a velocity of 150 ft/sec. The results of the ultrasonic NDE were compared with the results obtained using the destructive deply technique of Freeman (1984). The NDE method provides through-the-thickness information on damage and only requires access to a single side of the material, while the deply technique gives exact information on the actual damage. Good quantitative agreement between the two techniques was obtained.

Smith, B. T.↗

NASA NTRS1986

Combined bearing and bypass loading on a graphite/epoxy laminate

A combined experimental and analytical study was conducted to determine the behavior of a graphite/epoxy laminate subjected to combined bearing and bypass loading. Single-fastener quasi-isotropic specimens were loaded at various bearing-bypass ratios until damage was produced at the fastener hole. Damage-onset strengths and damage modes were then analyzed using local hole-boundary stresses calculated by a finite-element analysis. The tension data showed the expected linear interaction for combined bearing and bypass loading with damage developing in the net-section tension mode. However, the compression bearing-bypass strength showed an unexpected interaction involving the bearing mode.

Crews, J. H., Jr.↗

NASA NTRS1986

The effects of radiation on the interlaminar fracture toughness of a graphite/epoxy composite

An experimental study is made of the effect of electron irradiation (10 to the 10th rad), simulating a 30-year geosynchronous orbit exposure, on the fracture toughness of a graphite/epoxy composite, T300/934. The double cantilever beam (DBC) test is used to determine Mode I (peel) critical strain energy release rate and the edge delamination tension (EDT) test is used to determine mixed Mode I and II (peel and shear) critical strain energy release rate. It is found that the electron interaction of the epoxy matrix material enhances the fracture toughness properties of the composite and that the test temperature has a significant effect on the fracture toughness of both baseline and irradiated material.

Funk, J. G.↗

NASA NTRS1987

The effect of resin toughness and modulus on compressive failure modes of quasi-isotropic graphite/epoxy laminates

Compressive failure mechanisms in quasi-isotropic graphite/epoxy laminates were characterized for both unnotched and notched specimens and also following damage by impact. Two types of fibers (Thornel 300 and 700) and four resin systems (Narmco 5208, American Cyanamid BP907, and Union Carbide 4901/MDA and 4901/mPDA) were studied. For all material combinations, failure of unnotched specimens was initiated by kinking of fibers in the 0-degree plies. A major difference was observed, however, in the mode of failure propagation after the 0-degree ply failure. The strength of quasi-isotropic laminates in general increased with increasing resin tensile modulus. The laminates made with Thornel 700 fibers exhibited slightly lower compressive strengths than did the laminates made with Thornel 300 fibers. The notch sensitivity as measured by the hole strength was lowest for the BP907 resin and highest for the 5208 resin. For the materials studied, however, the type of fiber had no effect on the notch sensitivity.

Hahn, H. Thomas↗

NASA NTRS1987

Frequency and load ratio effects on critical strain energy release rate Gc thresholds of graphite/epoxy composites

Graphite/epoxy composite laminates of T300/BP907 and AS6/HST-7 were axial-tension fatigue tested. Tests were conducted at 5 and 10 Hz, and at loading ratios of R = 0.1 and R = 0.5. Edge delamination was monitored as a function of number of fatigue cycles by monitoring stiffness reduction during fatigue testing. Delamination was confirmed and documented using dye-enhanced X-ray and optical photography. Critical strain energy release rates were then calculated. The composites delaminated readily, with loading ratio having a significant influence. Frequency effects were negligible.

Adams, Donald F.↗

NASA NTRS1987

Rate effects on delamiantion fracture toughness of a toughened graphite/epoxy

The objective of this study was to determine the effects of loading rate on interlaminar fracture toughness of T300/F-185 graphite/epoxy composite, having an elastomer-modified epoxy resin matrix. Mode I interlaminar fracture was investigated by means of uniform width and width-tapered double cantilever beam (DCB) specimens. Hinged tabs were used to insure unrestrained rotation at the free ends. Specimens were loaded at quasi-static deflection rates of up to 8.5 mm/s corresponding to crack extension rates of up to 21 mm/s. Crack extension was monitored by means of strain gages mounted on the surface of the specimen. Continuous records were obtained of load, deflection, and crack extension for determination of the strain energy release rate. The latter was calculated by means of the area method and beam analysis method, and expressed as a power law of the crack extension velocity. Results indicate that the strain energy release rate decreases with crack velocity by over 20 percent over three decades of crack velocity.

Daniel, Isaac M.↗

NASA NTRS1988

Galvanic Corrosion In (Graphite/Epoxy)/Alloy Couples

Effects of galvanic coupling between graphite/epoxy composite material, G/E, and D6AC steel, 6061-T6 aluminum, and Inconel(R) 718 nickel alloy in salt water described in report. Introductory section summarizes previous corrosion studies of G/E with other alloys. Details of sample preparation presented along with photographs of samples before and after immersion.

Danford, Merlin D.↗

NASA NTRS1988

Stiffness Properties Of Laminated Graphite/Epoxy Cylinders

Report discusses stiffnesses of cylindrical shells formed from composite graphite/epoxy laminates, as calculated from traditional composite-lamination theory. Shells evaluated for use as cases for solid-fuel rocket motors. Stiffness results compared with quasi-experimental stiffnesses developed from pressure tests of cylindrical bottles. Sensitivities of stiffnesses to variations in constituent materials and in geometric parameters examined with help of two computer programs, included in appendix to report.

Tolbert, R. Noel↗

NASA NTRS1988

Graphite/Epoxy Deicing Heater

Heat applied close to surface protected. One ply of highly electrically- and thermally-conductive brominated-graphite fiber composite laminated between two plies of electrically-insulating composite material, with michel foil making contact with end portions of graphite fibers. Part of foil exposed beyond composite to serve as electrical contact. Graphite/Epoxy composite heater developed to prevent and reverse formation of ice on advanced composite surfaces of aircraft.

Hung, Ching-Cheh↗

NASA NTRS1987

Evaluation of closed cubic failure criterion for graphite/epoxy laminates

An analytical method has been developed to ensure closure of the cubic form of the tensor polynomial strength criterion. The intrinsic complexity of the cubic function is such that special conditions must be met to close the failure surface in three-dimensional stress space. These requirements are derived in terms of non-intersecting conditions for asymptotes and an asymptotic plane. To demonstrate the validity of this approach, closed failure surfaces were derived for two graphite/epoxy material systems (3M SP288-T300 and IM7 8551-7). The agreement of test data with this model clearly shows that it is possible to use a higher order cubic failure theory with confidence.

Tennyson, R. C.↗

NASA NTRS1988

Simulated impact damage in a thick graphite/epoxy laminate using spherical indenters

A study was made to determine the extent of fiber damage caused by low-velocity impact of spherical impactors to a very thick graphite/epoxy laminate. The laminate was cut from a filament wound case being developed for the Space Shuttle solid rocket motors. The case was wound using a wet process with AS4W graphite fiber and HBRF-55A epoxy. Impacts were simulated under quasi-static conditions by pressing hemispherically shaped indenters against the laminate at different locations. The contact force and indenter diameter were varied from location to location. The forces were chosen for each indenter diameter to produce contact pressures below and above that required to initiate damage. After the forces were applied, the laminate was cut into smaller pieces so that each piece contained a test site. The pieces were then deplied and the individual plies examined to determine the extent of fiber damage. Broken fibers were found in the outer layers directly beneath the contact site. The locus of broken fibers in each layer resembled a crack normal to the direction of the fibers. The maximum length and depth of the cracks increased with increasing contact pressure and indenter diameter. The internal stresses in the laminate were calculated using Hertz's law and Love's solution for pressure applied on part of the boundary of a semi-infinite body. The maximum length and depth of the cracks were predicted using a maximum shear stress criterion. Predictions and measurements were in good agreement.

Poe, C. C., Jr.↗

NASA NTRS1988

Ply-level failure analysis of a graphite/epoxy laminate under bearing-bypass loading

A combined experimental and analytical study was conducted to investigate and predict the failure modes of a graphite/epoxy laminate subjected to combined bearing and bypass loading. Tests were conducted in a test machine that allowed the bearing-bypass load ratio to be controlled while a single-fastener coupon was loaded to failure in either tension or compression. Onset and ultimate failure modes and strengths were determined for each test case. The damage-onset modes were studied in detail by sectioning and micrographing the damaged specimens. A two-dimensional, finite-element analysis was conducted to determine lamina strains around the bolt hole. Damage onset consisted of matrix cracks, delamination, and fiber failures. Stiffness loss appeared to be caused by fiber failures rather than by matrix cracking and delamination. An unusual offset-compression mode was observed for compressive bearing-bypass laoding in which the specimen failed across its width along a line offset from the hole. The computed lamina strains in the fiber direction were used in a combined analytical and experimental approach to predict bearing-bypass diagrams for damage onset from a few simple tests.

Naik, R. A.↗