Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Gas Turbine Combustor”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8
All sourcesNASA NTRSDOE OSTI
NASA NTRS1992

Numerical simulation of a low-emission gas turbine combustor using KIVA-II

A modified version of the KIVA-II code was used to obtain a multidimensional numerical solution for the turbulent two-phase chemically reacting flows inside a staged turbine combustor (STC). The STC under consideration is equipped with an advanced airblast fuel nozzle and encompasses a fuel nozzle (FN), a rich-burn (RB) zone, a converging connecting pipe, a quick-quench (QQ) zone, a diverging connecting pipe, and a lean-combustion (LC) zone. The STC was divided into two subsystems, namely, FN/RB zone and QQ/LC zones, and the numerical solutions were obtained separately for each subsystem. Preliminary data characterize the major features of the flow and temperature fields inside the STC. Information on velocity, temperature, and some critical species in the FN/RB zone is presented. In the QQ/LC zones, formation of the co- and counter-rotating bulk flow and the sandwiched-ring-shaped temperature field can be clearly seen. The calculations of the mass-weighted standard deviation and the pattern factor of temperature indicated that the mixing performance of the STC is very promising.

Yang, S. L.↗
NASA NTRS1992

Emissions reduction by varying the swirler airflow split in advanced gas turbine combustors

A rich burn/quick mix/lean burn (RQL) combustor concept for reducing pollutant emissions is currently under investigation at the NASA Lewis Research Center. The current study investigates the effect of varying the mass flow rate split between the swirler passages for an equivalance ratio of 2.0 on fuel distribution, temperature distribution, and emissions for the fuel nozzle/rich burn section of an RQL combustor. It is seen that optimizing these parameters can substantially improve combustor performance and reduce combustor emissions. The optimal mass flow rate split for reducing NO(x) emissions based on the numerical study was the same as found by experiment.

Micklow, Gerald J.↗
NASA NTRS1995

Sensitivity of Combustion-Acoustic Instabilities to Boundary Conditions for Premixed Gas Turbine Combustors

Premixed combustors, which are being considered for low NOx engines, are susceptible to instabilities due to feedback between pressure perturbations and combustion. This feedback can cause damaging mechanical vibrations of the system as well as degrade the emissions characteristics and combustion efficiency. In a lean combustor instabilities can also lead to blowout. A model was developed to perform linear combustion-acoustic stability analysis using detailed chemical kinetic mechanisms. The Lewis Kinetics and Sensitivity Analysis Code, LSENS, was used to calculate the sensitivities of the heat release rate to perturbations in density and temperature. In the present work, an assumption was made that the mean flow velocity was small relative to the speed of sound. Results of this model showed the regions of growth of perturbations to be most sensitive to the reflectivity of the boundary when reflectivities were close to unity.

Darling, Douglas↗
NASA NTRS1995

Combustion-acoustic stability analysis for premixed gas turbine combustors

Lean, prevaporized, premixed combustors are susceptible to combustion-acoustic instabilities. A model was developed to predict eigenvalues of axial modes for combustion-acoustic interactions in a premixed combustor. This work extends previous work by including variable area and detailed chemical kinetics mechanisms, using the code LSENS. Thus the acoustic equations could be integrated through the flame zone. Linear perturbations were made of the continuity, momentum, energy, chemical species, and state equations. The qualitative accuracy of our approach was checked by examining its predictions for various unsteady heat release rate models. Perturbations in fuel flow rate are currently being added to the model.

Darling, Douglas↗
NASA NTRS1996

Evaluation of Water Injection Effect on NO(x) Formation for a Staged Gas Turbine Combustor

NO(x) emission control by water injection on a staged turbine combustor (STC) was modeled using the KIVA-2 code with modification. Water is injected into the rich-burn combustion zone of the combustor by a single nozzle. Parametric study for different water injection patterns was performed. Results show NO(x) emission will decrease after water being injected. Water nozzle location also has significant effect for NO formation and fuel ignition. The chemical kinetic model is also sensitive to the excess water. Through this study, a better understanding of the physics and chemical kinetics is obtained, this will enhance the STC design process.

Fan, L.↗
NASA NTRS1996

Evaluation of Water Injection Effect on NO(x) Formation for a Staged Gas Turbine Combustor

NO(x) emission control by water injection on a staged turbine combustor (STC) was modeled using the KIVA-2 code with modification. Water is injected into the rich-burn combustion zone of the combustor by a single nozzle. Parametric study for different water injection patterns was performed. Results show NO(x) emission will decrease after water being injected. Water nozzle location also has significant effect for NO formation and fuel ignition. The chemical kinetic model is also sensitive to the excess water. Through this study, a better understanding of the physics and chemical kinetics is obtained, this will enhance the STC design process.

Fan, L.↗
NASA NTRS1998

Challenges to Laser-Based Imaging Techniques in Gas Turbine Combustor Systems for Aerospace Applications

Increasingly severe constraints on emissions, noise and fuel efficiency must be met by the next generation of commercial aircraft powerplants. At NASA Lewis Research Center (LeRC) a cooperative research effort with industry is underway to design and test combustors that will meet these requirements. To accomplish these tasks, it is necessary to gain both a detailed understanding of the combustion processes and a precise knowledge of combustor and combustor sub-component performance at close to actual conditions. To that end, researchers at LeRC are engaged in a comprehensive diagnostic investigation of high pressure reacting flowfields that duplicate conditions expected within the actual engine combustors. Unique, optically accessible flame-tubes and sector rig combustors, designed especially for these tests. afford the opportunity to probe these flowfields with the most advanced, laser-based optical diagnostic techniques. However, these same techniques, tested and proven on comparatively simple bench-top gaseous flame burners, encounter numerous restrictions and challenges when applied in these facilities. These include high pressures and temperatures, large flow rates, liquid fuels, remote testing, and carbon or other material deposits on combustor windows. Results are shown that document the success and versatility of these nonintrusive optical diagnostics despite the challenges to their implementation in realistic systems.

Locke, Randy J.↗
NASA NTRS1999

Non-Intrusive Laser-Induced Imaging for Speciation and Patternation in High Pressure Gas Turbine Combustors

The next generation of was turbine combustors for aerospace applications will be required to meet increasingly stringent constraints on fuel efficiency, noise abatement, and emissions. The power plants being designed to meet these constraints will operate at extreme conditions of temperature and pressure, thereby generating unique challenges to the previously employed diagnostic methodologies. Current efforts at NASA Glenn Research Center (GRC) utilize optically accessible, high pressure flametubes and sector combustor rigs to probe, via advanced nonintrusive laser techniques, the complex flowfields encountered in advanced combustor designs. The fuel-air mixing process is of particular concern for lowering NO(x) emissions generated in lean, premixed engine concepts. Using planar laser-induced fluorescence (PLIF) we have obtained real-time, detailed imaging of the fuel spray distribution for a number of fuel injector over a wide range of operational conditions that closely match those expected in the proposed propulsion systems. Using a novel combination of planar imaging, of fuel fluorescence and computational analysis that allows an examination of the flowfield from any perspective, we have produced spatially and temporally resolved fuel-air distribution maps. These maps provide detailed insight into the fuel injection at actual conditions never before possible, thereby greatly enhancing the evaluation of fuel injector performance and combustion phenomena.

Locke, Randy J.↗
NASA NTRS2002

Combustion Temperature Measurement by Spontaneous Raman Scattering in a Jet-A Fueled Gas Turbine Combustor Sector

Spontaneous vibrational Raman scattering was used to measure temperature in an aviation combustor sector burning jet fuel. The inlet temperature ranged from 670 K (750 F) to 756 K (900 F) and pressures from 13 to 55 bar. With the exception of a discrepancy that we attribute to soot, good agreement was seen between the Raman-derived temperatures and the theoretical temperatures calculated from the inlet conditions. The technique used to obtain the temperature uses the relationship between the N2 anti-Stokes and Stokes signals, within a given Raman spectrum. The test was performed using a NASA-concept fuel injector and Jet-A fuel over a range of fuel/air ratios. This work represents the first such measurements in a high-pressure, research aero-combustor facility.

Hicks, Yolanda R.↗
NASA NTRS2001

One-Dimensional Spontaneous Raman Measurements Made in a Gas Turbine Combustor

The NASA Glenn Research Center and the aerospace industry are designing and testing low-emission combustor concepts to build the next generation of cleaner, more fuel efficient aircraft powerplants. These combustors will operate at much higher inlet temperatures and at pressures that are up to 3 to 5 times greater than combustors in the current fleet. From a test and analysis viewpoint, there is an increasing need for measurements from these combustors that are nonintrusive, simultaneous, multipoint, and more quantitative. Glenn researchers have developed several unique test facilities (refs. 1 and 2) that allow, for the first time, optical interrogation of combustor flow fields, including subcomponent performance, at pressures ranging from 1 to 60 bar (1 to 60 atm). Experiments conducted at Glenn are the first application of a visible laser-pumped, one-dimensional, spontaneous Raman-scattering technique to analyze the flow in a high-pressure, advanced-concept fuel injector at pressures thus far reaching 12 bar (12 atm). This technique offers a complementary method to the existing two- and three-dimensional imaging methods used, such as planar laser-induced fluorescence. Raman measurements benefit from the fact that the signal from each species is a linear function of its density, and the relative densities of all major species can be acquired simultaneously with good precision. The Raman method has the added potential to calibrate multidimensional measurements by providing an independent measurement of species number-densities at known points within the planar laser-induced fluorescence images. The visible Raman method is similar to an ultraviolet-Raman technique first tried in the same test facility (ref. 3). However, the visible method did not suffer from the ultraviolet technique's fuel-born polycyclic aromatic hydrocarbon fluorescence interferences.

DeGroot, Wilhelmus A.↗
NASA NTRS2018

CFD Predictions of N+3 Cycle Emissions for a Three-Cup Gas-Turbine Combustor

The National Combustion Code (OpenNCC) was used to perform non-reacting and two-phase reacting flow computations for a unique pre-filming type LDI-3 fuel injector for a three-cup, nineteen-element flametube configuration. All computations were performed with a consistent approach of mesh-generation, spray modeling, reduced finite-rate kinetics and turbulence-chemistry interaction, as developed for CFD analysis of single-element and multi-element LDI-3 designs with OpenNCC. Emissions and flowfield characteristics were predicted for a generic NASA N+3 engine cycle, with particular focus on the 7% and 30% ICAO power operating conditions. For both the conditions studied, the CFD analysis provided very good predictions for EINOx when compared with experimental data measured at NASA Glenn Research Center.

injectors↗
NASA NTRS2019

Pilot Injector Redesign to Reduce N+3 Cycle Emissions for a Gas-Turbine Combustor

An overview is given of an effort for the use of CFD analysis to complement design and configuration definition of third generation Lean-Direct Injection combustion concepts (LDI-3) for NASA’s N+3 program. The National Combustion Code (OpenNCC) was used to perform non-reacting and two-phase reacting flow computations for a three-cup, nineteen-element flame tube array with redesigned pilot injectors to improve spray and emissions characteristics when compared to a previous LDI-3 design. All computations were performed with a consistent approach to mesh-generation, spray modeling, ignition and kinetics modeling for a ‘medium-power’ cycle condition. Computational predictions of the aerodynamics of a new pre-filming pilot injector were used to arrive at an optimized aerothermal design that meets effective area and fuel-air mixing criteria. The newly designed pilot injectors were shown to provide considerable improvements in aerodynamic stability, flame-tube pattern factor and NOx emissions, when compared to the original design.

nitrogen oxides injectors↗
NASA NTRS2019

Pilot Injector Redesign to Reduce N+3 Cycle Emissions for a Gas-Turbine Combustor

An overview is given of an effort for the use of CFD analysis to complement design and configuration definition of third generation Lean-Direct Injection combustion concepts (LDI-3) for NASA's N plus 3 program. The National Combustion Code (OpenNCC) was used to perform non-reacting and two-phase reacting flow computations for a three-cup, nineteen-element flametube array with redesigned pilot injectors to improve spray and emissions characteristics when compared to a previous LDI-3 design. All computations were performed with a consistent approach to mesh-generation, spray modeling, ignition and kinetics modeling for a "medium-power" cycle condition. Computational predictions of the aerodynamics of a new pre-filming pilot injector were used to arrive at an optimized aerothermal design that meets effective area and fuel-air mixing criteria. The newly designed pilot injectors were shown to provide considerable improvements in aerodynamic stability, flame-tube pattern factor and NOx emissions, when compared to the original design.

Nitrogen Oxides↗
NASA NTRS2019

Applying Optical Diagnostics to Study Aircraft Gas Turbine Combustor Performance

This is for an invited lecture at Cleveland State University for a combustion course. The presentation gives an overview of some of the optical diagnostic techniques the Combustion Branch uses to characterize research fuel injection concepts to reduce emissions. Examples are provided that come from previously presented conference papers

Hicks, Yolanda R.↗
NASA NTRSDate not supplied

Lean Blowout (LBO) Simulations in a Rich-Burn Quick-Quench Lean-Burn (RQL) Gas Turbine Combustor

The transient processes involving lean blowout (LBO) in a RQL combustor such as the single cup combustor in the National Jet Fuels Combustion Program (NJFCP) referee rig are simulated with the reduced mechanisms based on Hybrid Chemistry for two different fuels, Cat-A2 and Cat-C1. Cat-A2 fuel is Jet-A with average or nominal properties based on a survey of the Petroleum Quality Information System database. The Cat-C1, an alternative jet fuel, is a GEVO alcohol-to-jet (ATJ) fuel composed almost entirely of two highly-branched C12 and C16 iso-paraffins. Experiments conducted in the NJFCP referee rig established a stable flame at an equivalence ratio of 0.096 (the near LBO condition) as the starting condition for LBO tests performed with all Category A and C fuels. Simulations of the approach to LBO verify that a stable flame is established at the near-LBO condition for each fuel before reducing fuel flow rate (and thus equivalence ratio) in a step-wise manner. At each new equivalence ratio, the global heat release rate and total fuel evaporation time histories are monitored to verify a new stable flame condition has been established before performing the next reduction in equivalence ratio until the flame is approaching the blowout. Main conclusions are threefold: (1) For Cat-C1 fuel the equivalence ratio for LBO is around 0.087. (2) For Cat-A2 fuel the equivalence ratio for LBO is either 0.082 or 0.078 depended on the time span of equivalence ratio of 0.085. (3) The averaged difference from LES on LBO for Cat-C1 relative to Cat-A2 is 8.75% versus 7.8% from the experimental data.

LES, Lean blow out↗