Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Freestream Velocity”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8
All sourcesNASA NTRSDOE OSTI
NASA NTRS2019

Two-Point Focused Laser Differential Interferometry Second-Mode Measurements at Mach 6

A two-point focused laser differential interferometer (FLDI) is used to make measurements of density fluctuations on a 7 degree half-angle cone in a Mach 6 flow. The system was first characterized in the laboratory using laser induced breakdown to provide a well defined density fluctuation. The speed of the shock wave generated by the breakdown is verified using simultaneous high-speed schlieren. The FLDI system is then installed at the NASA Langley 20-Inch Mach 6 air tunnel to make measurements in the boundary layer of the 7 degree half-angle cone model and in the tunnel freestream for a unit Reynolds number range of 3.0 to 8.22 x 10(exp 6)/ft. Second-mode packets are visible in the spectra, with peak frequencies increasing linearly and peak amplitude increasing as a function of unit Reynolds number. The two-point measurement allows for the calculation of the second-mode wavepacket speeds, which propagate between 88% and 92% of the freestream velocity of the tunnel for all Reynolds numbers. The FLDI measurements are compared to surface-mounted fast-response pressure transducer measurements, where second-mode frequencies and wavepacket speeds are in good agreement.

Weisberger, Joshua M.↗
NASA NTRSDate not supplied

Flow Physics Study of Sweeping Jet Actuation on a NACA 0015 Swept Wing Configuration

Preliminary results from a recently completed active flow control (AFC) experiment on a 30 deg swept, semispan wing are presented. The constant chord NACA 0015 wing is configured with sweeping jet actuators at the flap shoulder to study the effects of excitation introduced into a separated, three-dimensional flowfield. The research is aimed at developing efficient active flow control approaches for swept wing configurations. Oil and tuft flow visualization data, steady and unsteady pressure data, particle image velocimetry (PIV), oil flow interferometry (OFI), and force and moment data are used to compare the flowfields with and without AFC. The parameters that were varied include freestream velocity, actuator momentum coefficient, and flap deflection angle.

active flow control↗
NASA NTRS2004

Low and High Speed STOVL Configurations in Ground Effect

The problem of hot gas ingestion in V/STOL and STOVL aircraft has motivated a set of experimental studies. Two-, three-, and four-jet configurations in cross flow were studied in ground effect. The results presented here were based on a quantitative, concentration measurement technique know as marker nephelometry. The effects of configuration, velocity ratio (freestream over jet velocity), model height, and inlet suction were investigated. The experiments were conducted in three parts. In the first part, comparisons of low speed two-, three-, and four-jet configurations were made. Measurements were made in the planes beneath the models in ground effect. As the number of jets increased, the vortical structures in the flowfield were found to move further upstream due to the increased total momentum. In the second part of the experiments, measurements were made at the inlet entry plane of the low speed two- and three-jet configurations in ground effect. The results indicated that ingestion occurred intermittently, especially in the upper portions of the inlets. The highest levels of concentrations were measured at a model height of two jet diameters. As the model height increased, the concentration levels decreased. Finally, a high speed, two-jet configuration without inlet suction was studied. The flowfield structures were generally found to move further downstream as the jet velocity increased at a constant velocity ratio.

Holdeman, James D.↗
DOE OSTI2022

Pacific Marine Energy Center Laser Doppler Velocimetry Commissioning

First commissioning data for the new laser doppler velocimetry (LDV) system that will be used at the Tyler Flume at the University of Washington. The LDV system can measure three components of velocity at a point. For this dataset the three components were operated in non-coincident mode and data were acquired at the center of the empty facility. Comparisons of freestream turbulence were made with a Vectrino slightly upstream of the LDV measurement location.

16 TIDAL AND WAVE POWER↗
DOE OSTI2021

Applying Time-Parallelization to Turbulent Flows

Parallelization of the temporal domain is explored for the solution of turbulent flows. Multigrid reduction-in-time (MGRIT) is used to advance the large-scale fluid dynamics in time sequentially on the coarsest space-time grid but propagate the information in time parallel on all other levels. The goal of this process is to accurately and efficiently resolve the coarse-scale turbulence structure and use that to drive the fine-scales of the turbulent flow. The extra forcing from nonlinear multigrid facilitates the coupling and interaction between fine and coarse scales, through which the multiscale nonlinear physics is properly captured. Adaptive mesh refinement is employed to finely resolve only the regions with strong gradients, which provides further computational efficiency. The underlying computational fluid dynamics solver is a fourth-order finite-volume scheme with the standard 4-stage Runge-Kutta method. An advanced approach is devised and implemented to enable MGRIT to solve highly turbulent flows successfully. Furthermore, the method is applied to solve a Taylor-Green vortex problem and a doubleshear-layer turbulent mixing flow. Results are promising, validating that MGRIT with the filtering approach has the potential to efficiently solve general turbulent flows.

Computational Fluid Dynamics↗
NASA NTRS1980

Autoignition characteristics of aircraft-type fuels

The ignition delay characteristics of Jet A, JP 4, no. 2 diesel, cetane and an experimental referee broad specification (ERBS) fuel in air at inlet temperatures up to 1000 K, pressures of 10, 15, 20, 25 and 30 atm, and fuel air equivalence ratios of 0.3, 0.5, 0.7 and 1.0 were mapped. Ignition delay times in the range of 1 to 50 msec at freestream flow velocities ranging from 20 to 100 m/sec were obtained using a continuous flow test apparatus which permitted independent variation and evaluation of the effect of temperature, pressure, flow rate, and fuel/air ratio. The ignition delay times for all fuels tested appeared to correlate with the inverse of pressure and the inverse exponent of temperature. With the exception of pure cetane, which had the shortest ignition delay times, the differences between the fuels tested did not appear to be significant. The apparent global activation energies for the typical gas turbine fuels ranged from 38 to 40 kcal/mole, while the activation energy determined for cetane was 50 kcal/mole. In addition, the data indicate that for lean mixtures, ignition delay times decrease with increasing equivalence ratio. It was also noted that physical (apparatus dependent) phenomena, such as mixing (i.e., length and number of injection sites) and airstream cooling (due to fuel heating, vaporization and convective heat loss) can have an important effect on the ignition delay.

Spadaccini, L. J.↗
NASA NTRS1981

Autoignition characteristics of no. 2 diesel fuel

Parametric tests to map the ignition delay characteristics were conducted at pressures of 3, 4, and 5 atm, inlet air temperatures up to 1150 K and fuel air equivalence ratios ranging from 0.2 to 1.0. Ignition delay times in the range of 6 msec to 60 msec at freestream flow velocities ranging from 10 m/sec to 40 m/sec were obtained. The ignition delay times appeared to correlate with the inverse of pressure and the inverse exponent of temperature.

Tevelde, J. A.↗
NASA NTRS1989

On the freestream matching condition for stagnation point turbulent flows

The problem of plane stagnation point flow with freestream turbulence is examined from a basic theoretical standpoint. It is argued that the singularity which arises from the standard kappa-epsilon model is not due to a defect in the model but results from the use of an inconsistent freestream boundary condition. The inconsistency lies in the implementation of a production equals dissipation equilibrium hypothesis in conjunction with a freestream mean velocity field that corresponds to homogeneous plane strain - a turbulent flow which does not reach such a simple equilibrium. Consequently, the adjustment that has been made in the constants of the epsilon-transport equation to eliminate this singularity is not self-consistent since it is tantamount to artificially imposing an equilibrium structure on a turbulent flow which is known not to have one.

Speziale, Charles G.↗
NASA NTRS1989

Physical analysis and second-order modelling of an unsteady turbulent flow - The oscillating boundary layer on a flat plate

The turbulent boundary layer under a freestream whose velocity varies sinusoidally in time around a zero mean is computed using two second order turbulence closure models. The time or phase dependent behavior of the Reynolds stresses are analyzed and results are compared to those of a previous SPALART-BALDWIN direct simulation. Comparisons show that the second order modeling is quite satisfactory for almost all phase angles, except in the relaminarization period where the computations lead to a relatively high wall shear stress.

Ha Minh, H.↗
NASA NTRS1990

A computational study of the taxonomy of vortex breakdown

The results of a fully three-dimensional numerical simulation of vortex breakdown using the unsteady, incompressible Navier-Stokes equations are presented. The solutions show that the freestream axial velocity distribution has a significant effect on the position and type of vortex breakdown. Common features between bubble-type and spiral-type breakdown are identified and the role of flow stagnation and the critical state are discussed as complimentary ideas describing the initiation of breakdown.

Spall, Robert E.↗
NASA NTRS1989

On the freestream matching condition for stagnation point turbulent flows

The problem of plane stagnation point flow with freestream turbulence is examined from a basic theoretical standpoint. It is argued that the singularity which arises from the standard kappa-epsilon model is not due to a defect in the model but results from the use of an inconsistent freestream boundary condition. The inconsistency lies in the implementation of a production equals dissipation equilibrium hypothesis in conjunction with a freestream mean velocity field that corresponds to homogeneous plane strain - a turbulent flow which does not reach such a simple equilibrium. Consequently, the adjustment that has been made in the constants of the epsilon-transport equation to eliminate this singularity is not self-consistent since it is tantamount to artificially imposing an equilibrium structure on a turbulent flow which is known not to have one.

Speziale, C. G.↗
NASA NTRS1991

A computational study of the topology of vortex breakdown

A fully three-dimensional numerical simulation of vortex breakdown using the unsteady, incompressible Navier-Stokes equations has been performed. Solutions to four distinct types of breakdown are identified and compared with experimental results. The computed solutions include weak helical, double helix, spiral, and bubble-type breakdowns. The topological structure of the various breakdowns as well as their interrelationship are studied. The data reveal that the asymmetric modes of breakdown may be subject to additional breakdowns as the vortex core evolves in the streamwise direction. The solutions also show that the freestream axial velocity distribution has a significant effect on the position and type of vortex breakdown.

Spall, Robert E.↗
NASA NTRS2001

Experimental Investigation of Transition to Turbulence as Affected By Passing Wakes

This paper presents experimental results from a study of the effects of periodically passing wakes upon laminar-to-turbulent transition and separation in a low-pressure turbine passage. The test section geometry is designed to simulate unsteady wakes in turbine engines for studying their effects on boundary layers and separated flow regions over the suction surface by using a single suction surface and a single pressure surface to simulate a single turbine blade passage. Single-wire, thermal anemometry techniques are used to measure time-resolved and phase averaged, wall-normal profiles of velocity, turbulence intensity and intermittency at multiple streamwise locations over the turbine airfoil suction surface. These data are compared to steady-state wake-free data collected in the same geometry to identify the effects of wakes upon laminar-to-turbulent transition. Results are presented for flows with a Reynolds number based on suction surface length and stage exit velocity of 50,000 and an approach flow turbulence intensity of 2.5%. While both existing design and experimental data are primarily concerned with higher Reynolds number flows (Re greater than 100,000), recent advances in gas turbine engines, and the accompanying increase in laminar and transitional flow effects, have made low-Re research increasingly important. From the presented data, the effects of passing wakes on transition and separation in the boundary layer, due to both increased turbulence levels and varying streamwise pressure gradients are presented. The results show how the wakes affect transition. The wakes affect the flow by virtue of their difference in turbulence levels and scales from those of the free-stream and by virtue of their ensemble- averaged velocity deficits, relative to the free-stream velocity, and the concomitant changes in angle of attack and temporal pressure gradients. The relationships between the velocity oscillations in the freestream and the unsteady velocity profile shapes in the near-wall flow are described. In this discussion is support for the theory that bypass transition is a response of the near-wall viscous layer to pressure fluctuations imposed upon it from the free-stream flow. Recent transition models are based on that premise. The data also show a significant lag between when the wake is present over the surface and when transition begins.cous layer to pressure fluctuations imposed upon it from the free-stream flow. Recent transition models are based on that premise. The data also show a significant lag between when the wake is present over the surface and when transition begins.cous layer to pressure fluctuations imposed upon it from the free-stream flow. Recent transition models are based on that premise. The data also show a significant lag between when the wake is present over the surface and when transition begins.

Kaszeta, Richard W.↗
NASA NTRS2020

Assessment of Transition Modeling Capability in OVERFLOW with Emphasis on Swept-Wing Configurations

In preparation for comparisons with data obtained from the recently concluded experiments in the National Transonic Facility at the NASA Langley Research Center on the new common research model with natural laminar flow (CRM-NLF), an assessment of the current transition modeling capability in the NASA OVERFLOW 2.2o code has been carried out. A combination of the available experimental data and linear stability analysis is used to evaluate the accuracy and robustness of these models for selected swept-wing type configurations, with significant crossflow. An additional goal for this work involves providing a comparative assessment of the relevant transition models in the context of a single flow solver and identifying model limitations as well as the potential for future improvements that would help strengthen the physical basis of such transition models. Included in this investigation is an assessment of the sensitivities of the underlying transition models to grid resolution (wall-normal, as well as streamwise and spanwise) and the values of extra input parameters such as the level of surface roughness and freestream turbulence variables. The flow configurations targeted in this assessment include the NASA NLF(2)-0415 swept-wing configuration, the sickle-shaped wing introduced by the Technical University of Braunschweig, and the wing-body configuration of the CRM model from the fourth and fifth AIAA CFD Drag Prediction Workshops.

Freestream velocity↗
NASA NTRS2021

Hypersonic Second Mode Instability Response to Shaped Roughness

An experimental campaign was conducted on a 7-degree half-angle cone in the NASA Langley Research Center 20-Inch Mach 6 Wind Tunnel to examine the influence of arrays of regularly spaced roughness elements on instability growth and transition. The primary element shape was a pair of elliptical planform ramps that were inclined at equal and opposite angles with respect to the local streamwise direction. The element shapes were designed to induce transient growth disturbances that would lead to sustained azimuthal modulation of the boundary layer flow while limiting the nearfield disturbances to avoid an immediate, i.e., effective tripping of the boundary layer. The bulk of the run matrix consisted of testing different element height sat free stream unit Reynolds numbers ranging from 9.8 to 13.1 million per meter. Other element shapes previously designed for tripping hypersonic boundary layers were also implemented. The model was instrumented with surface mounted Kulite ® and PCB ® pressure transducers and thermocouples. Spectra from the PCBs ® indicated clear suppression of the second-mode instability; however, neither the PCB ® spectra nor the heat transfer data presented strong evidence for delayed turbulent flow. Complementary stability computations likewise demonstrated second-mode reduction, particularly just downstream of the roughness, but also revealed a rise in first mode (streak-instability) amplitudes from the baseline that was likely responsible for the earlier transition observed for taller roughness cases.

Hypersonics↗
NASA NTRS2021

Transition Analysis for the CRM-NLF Wind Tunnel Configuration

This paper reports the results of a comprehensive linear stability analysis of the boundary layer flow over the common research model with natural laminar flow (CRM-NLF) aircraft configuration. The flow conditions match selected test conditions from a recent wind tunnel experiment in the National Transonic Facility at the NASA Langley Research Center. Previous work has shown that the measured onset of laminar-turbulent transition during the experiments can be correlated with the linear amplification of Tollmien-Schlichting (TS) and stationary crossflow (CF) instabilities in the swept wing boundary layer. However, a significant scatter ( N ∈ (4,9)) was observed in the values of the logarithmic amplification factor along the measured transition front. This previous analysis was based on an approximate basic state (based on a boundary layer code with conical flow approximation) and parallel stability computations without surface curvature effects. Here, we examine the effects of these various approximations with the goal of quantifying the resulting changes in the N-factor correlations. Specifically, both linear stability theory (LST) and the parabolized stability equations (PSE)are used in conjunction with an accurate definition of the laminar boundary layer flow as computed with a Navier-Stokes solver with a Reynolds-Averaged-Navier-Stokes (RANS) based turbulence model within the turbulent parts of the flow. Furthermore, the effects of instability wave propagation within a fully three-dimensional boundary layer are also evaluated by integrating the disturbance growth rates along suitably chosen, curvilinear (i.e., nonplanar) propagation trajectories. The results of this analysis are also used in an accompanying paper by Venkatachari et al. to develop improved, physics based transition predictions for the same CRM-NLF configuration.

Boundary layer transition↗
NASA NTRS2021

Hypersonic Second-Mode Instability Response to Shaped Roughness

An experimental campaign was conducted on a 7-degree half-angle cone in the NASA Langley Research Center 20-Inch Mach 6 Wind Tunnel to examine the influence of arrays of regularly spaced roughness elements on instability growth and transition. The primary element shape was a pair of elliptical planform ramps that were inclined at equal and opposite angles with respect to the local streamwise direction. The element shapes were designed to induce transient growth disturbances that would lead to sustained azimuthal modulation of the boundary layer flow while limiting the nearfield disturbances to avoid an immediate, i.e., effective tripping of the boundary layer. The bulk of the run matrix consisted of testing different element height sat free stream unit Reynolds numbers ranging from 9.8 to 13.1 million per meter. Other element shapes previously designed for tripping hypersonic boundary layers were also implemented. The model was instrumented with surface mounted Kulite ® and PCB ® pressure transducers and thermocouples. Spectra from the PCBs ® indicated clear suppression of the second-mode instability; however, neither the PCB ® spectra nor the heat transfer data presented strong evidence for delayed turbulent flow. Complementary stability computations likewise demonstrated second-mode reduction, particularly just downstream of the roughness, but also revealed a rise in first mode (streak-instability) amplitudes from the baseline that was likely responsible for the earlier transition observed for taller roughness cases.

Hypersonics↗
NASA NTRS2021

Transition Analysis for the CRM-NLF Wind Tunnel Configuration

This paper presents the results of an ongoing study into the linear stability characteristics of the boundary layer flow over the common research model with natural laminar flow (CRMNLF) aircraft configuration. The flow conditions match selected test conditions from a recent wind tunnel experiment in the National Transonic Facility at the NASA Langley Research Center. Previous work involving parallel stability computations of a boundary layer flow based on the conical flow approximation has shown that the measured onset of laminar-turbulent transition during the experiments can be correlated with the linear amplification of Tollmien- Schlichting (TS) and stationary crossflow (CF) instabilities in the swept wing boundary layer. Here, we examine the effects of the simplifying approximations in both basic state computation and the stability analysis, with the goal of quantifying the resulting changes in the N-factor correlations. Specifically, the basic states are computed by using full Navier-Stokes equations and the stability analysis is performed by using a nonorthogonal coordinate system that allows a clear distinction between planar TS and CF instabilities. Furthermore, the effects of curvature and nonparallel mean flow have been included in the stability computations based on the parabolized stability equations (PSE). The fully turbulent Reynolds-Averaged-Navier-Stokes (RANS) mean flow solutions show good agreement with the measured wall pressure distribution. Viscous-inviscid interactive effects are observed to be important because the shock fronts along the suction surface are influenced by the imposed transition front. The stability results confirm the previous findings related to TS amplification within the inboard region of the wing and the dominance of stationary CF modes in the outboard region. However, given the close proximity of the measured transition front and the dual shock system within the outer part of the wing, the onset of transition may well be shock limited within the outboard region. In general, the transition criterion based on the dual N-factor method with N TS = N CF = 6 is reasonably successful at correlating with the measured transition fronts at Re MAC = 15 million and AoA = 1.5, 2 degrees; however, the low values of the correlating N-factors at Re MAC = 17.5 million support the hypothesis that the measured transition at the higher Reynolds number may have been strongly influenced by the merging of turbulent wedges that originate from surface imperfections near the leading edge.

Boundary layer transition↗