Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “FRACTURE TOUGHNESS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8
All sourcesNASA NTRSDOE OSTI
NASA NTRS1982

A simple test for the interlaminar fracture toughness of composites

A simple test method for the measurement of delamination resistance is assessed through its application to 11-ply graphite-epoxy laminates whose matrices employ the F185 and 205 resins. The F185 resin has the same base epoxy as the 205, to which liquid and solid elastomers have been added. The critical value of the mixed mode energy release rate, calculated from a closed form equation employing nominal strain measurements from the onset of edge delamination, show that addition of the elastomers to the base epoxy increases interlaminar fracture toughness. Comparison of these results with those of width-tapered double cantilever beam (WTDCB) test data for the two materials shows a similar strain energy release rate, establishing the accuracy of the novel method. Both tests are found to be needed, however, for the quantitative characterization of interlaminar fracture toughness.

Obrien, T. K.↗
NASA NTRS1984

On the use of the three point bend and compact tension specimens to measure fracture toughness of composite laminates

The influence of specimen thickness on the fracture toughness of two laminates and three specimen geometries was investigated. As thickness increased the toughness decreased and approached an asymptotic value that was dependent upon the type of laminate but was practically independent of specimen geometry. Enhanced X-ray photographs and removal of an outside ply revealed that most of the delaminations were surface effects.

Harris, C. E.↗
NASA NTRS1988

Height-tapered double cantilever beam specimen for study of rate effects on fracture toughness of composites

Loading rate effects on the mode I delamination fracture toughness of AS4/3501-6 graphite/epoxy are presently studied by means of a height-tapered double-cantilever beam specimen whose height contour is designed to furnish a slightly decreasing compliance with increasing crack length, in order to yield a stable and smooth crack propagation at high loading rates. This specimen geometry also allows much higher crack propagation velocities to be obtained with either uniform or width-tapered double cantilever beam specimens.

Yaniv, Gershon↗
NASA NTRS1990

An evaluation of the fatigue crack growth and fracture toughness properties of beryllium-copper alloy CDA172

A series of fracture mechanics tests, using the Be-Cu alloy CDA172 in the round rod product form, was conducted in a lab air environment at room temperature. Tensile data is presented in both the L and C directions and K sub Ic data in both the C-R and C-L orientations. Fracture toughness values were derived from M(T) (center cracked), PS(T) (surface cracked) and CC01 (corner cracked) specimens of varying thickness. Fatigue crack growth data were obtained for the C-R orientation at stress ratio of 0.1, 0.4, and 0.7 and for the C-L orientation at stress ratios of 0.1, 0.3, 0.4, and 0.7.

Forman, Royce G.↗
NASA NTRS1992

Fracture toughness of an Al-Li-Cu-In alloy

The crack initiation and growth fracture toughness of select AL-Li-Cu alloy variants are characterized and elucidated. Conventionally processed plates form large DC cast ingots are investigated to eliminate the variation in microstructure associated with laboratory scale and SPF-processed material. Fracture resistance is characterized using the J-integral method to establish crack initiation and growth behavior at 25 and -185 C. It is shown that state-of-the-art 2090-T81 has superior toughness compared to 2090 + In-T6 at both test temperatures, with the low toughness of 2090 + In-T6 associated with intersubgranular fracture attributed to a high density of subboundary precipitates.

Wagner, John A.↗
NASA NTRS1976

A study of the effect of subcritical crack growth on the geometry dependence on nonlinear fracture toughness parameters

The effect of subcritical crack growth on the geometry dependence of nonlinear fracture toughness parameters was studied by comparing the toughness values for different specimen geometries at the onset of subcritical crack growth and at the initiation of unstable crack propagation. Center-cracked thin sheet specimens of 2024-T3 and 7075-T6 aluminum alloys were tested by varying the specimen length L, width w, and crack length-to-width ratio c/w. When the onset of unstable crack propagation was selected as the critical point, the nonlinear energy toughness and the R curve toughness increased with increasing w and decreasing L and c/w. However, when the onset of subcritical crack growth was taken as the critical point, energy toughness and the linear toughness values were independent of these geometrical variables.

Jones, D. L.↗
NASA NTRS1977

The influence of composition, annealing treatment, and texture on the fracture toughness of Ti-5Al-2.5Sn plate at cryogenic temperatures

The plane strain fracture toughness K sub Ic and conventional tensile properties of two commercially produced one-inch thick Ti-5Al-2.5Sn plates were determined at cryogenic temperatures. One plate was extra-low interstitial (ELI) grade, the other normal interstitial. Portions of each plate were mill annealed at 1088 K (1500 F) followed by either air cooling or furnace cooling. The tensile properties, flow curves, and K sub Ic of these plates were determined at 295 K (room temperature), 77 K (liquid nitrogen temperature), and 20 K (liquid hydrogen temperature).

Vanstone, R. H.↗
NASA NTRS2026

Cryogenic Mixed Mode I – Mode II Fracture Toughness of Various Polymer Composite Materials

The present study investigates the mixed mode interlaminar fracture toughness of six polymer matrix composite materials at both room temperature and cryogenic liquid nitrogen temperature. The single leg bending test employed gives a mix of Mode I (opening) and Mode II (in-plane shearing) cracking. The tested thermoplastic-matrix composites were shown to have total mixed mode toughnesses 3.1–4.3 times higher than those of representative thermoset resin composites.

Carbon fiber↗