SEARCH · Engineering Papers

Results for “ELECTRIC MOTOR”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8

All sources NASA NTRS DOE OSTI

NASA NTRS1981

Testing of the permanent magnet material Mn-Al-C for potential use in propulsion motors for electric vehicles

The development of Mn-Al-C permanent magnets is reviewed. The general properties of the material are discussed and put into perspective relative to alnicos and ferrites. The traction motor designer's demands of a permanent magnet for potential use in electric vehicle drives are reviewed. Tests determined magnetic design data and mechanical strength properties. Easy axis hysteresis and demagnetization curves, recoil loops and other minor loop fields were measured over a temperature range from -50 to 150 C. Hysteresis loops were also measured for three orthogonal directions (the one easy and two hard axes of magnetization). Extruded rods of three different diameters were tested. The nonuniformity of properties over the cross section of the 31 mm diameter rod was studied. Mechanical compressive and bending strength at room temperature was determined on individual samples from the 31 mm rod.

Abdelnour, Z.↗

NASA NTRS1972

Waveguide switch protector

Device for detecting excessive operation of electric motors used to drive waveguide switches is described. Purpose of device is to prevent burnout of electric motor in event of waveguide stoppage at some point other than extreme limits of travel. Operation of equipment, components used to sense motor performance, and schematic diagram are included.

Kolbly, R. B.↗

NASA NTRS2018

Low-Noise Operating Mode for Propeller-Driven Electric Airplanes

Mechanical shaft power and shaft speed of reciprocating internal combustion engines are closely coupled. Maximum rated shaft power is typically produced at or near peak shaft speed. If a general aviation airplane equipped with a reciprocating engine and a variable-pitch propeller attempts a low-noise takeoff by reducing propeller tip speed, propeller power and thrust are reduced. Such takeoffs are not tolerated due to punishing performance effects, such as increased field lengths and poor climb rates. Certain electric motors, however, are able to deliver maximum shaft power over a wide range of shaft speed. Electric or hybrid-electric propeller-driven airplanes should be able to exploit this behavior. At low shaft speeds, high shaft power levels and high blade pitch angles could be combined to recover much of the thrust that would otherwise be lost. This could enable a low-noise operating mode for propellers normally designed for performance rather than for noise. The subject of this paper is an analytical investigation into low-noise takeoffs and steady overflights of a notional general aviation airplane equipped with a propeller driven by an electric motor.

Berton, Jeffrey J.↗

NASA NTRS1980

Testing of the permanent magnet material Mn-Al-C for potential use in propulsion motors for electric vehicles

The development of Mn-Al-C permanent magnets is reviewed. The general properties of the material are discussed and put into perspective relative to alnicos and ferrites. The commercial material now available is described by the manufacturer's data. The traction motor designer's demands of a permanent magnet for potential use in electric vehicle drives are reviewed. From this, a list of the needed specific information is extracted. A plan for experimental work is made which would generate this information, or verify data supplied by the producer. The results of these measurements are presented in the form of tables and graphs. The tests determined magnetic design data and some mechanical strength properties. Easy axis hysteresis and demagnetization curves, recoil loops and other minor loop fields were measured over a temperature range from -50 C to +150 C. Hysteresis loops were also measured for three orthogonal directions (the easy and 2 hard axes of magnetization).

Abdelnour, Z. A.↗

NASA NTRS1987

Lapping and Polishing an Elliptical Bore

Numerically controlled milling machine modified to make head reciprocate. Modification accomplished by removal of original milling head from machine and by mounting vertical slide in its place. Vertical slide driven up and down by connecting rod bolted off-center to drive pulley. Pulley driven by belt from variable-speed electric motor. Milling-machine head then attached to vertical slide. Mechanism allowed independent control of reciprocating surface speed through variation of speed of electric motor.

Loggan, John J., Jr.↗

NASA NTRS2022

Genetic Optimization of Planetary Gearboxes Based on Analytical Gearing Equations

Electric and hybrid electric vertical takeoff and landing vehicles will require high performance electric motor driven propulsion systems to enable fuel burn and emissions benefits over traditional liquid fuel powered rotorcraft. One key to the design of a high performance electric motor driven propulsion systems is to be able to estimate the mass and efficiency of a gearbox at various motor and propellor operating speeds. Knowing how gearbox mass and efficiency trade with motor and propellor rotational speed, allows motor and propellor RPM to be traded in an overall optimization of the propulsion system. In this paper, a genetic optimization tool for estimating the mass and efficiency of gearboxes is presented. Example results from the tool are presented and compared to existing correlations in use by NASA aircraft design codes.

Thomas Tallerico↗

NASA NTRS1983

Permanent-Magnet Motors and Generators for Aircraft

Electric motors and generators that use permarotating machinery, but aspects of control and power conditioning are also considered. The discussion is structured around three basic areas: rotating machine design considerations presents various configuration and material options, generator applications provides insight into utilization areas and shows actual hardware and test results, and motor applications provides the same type of information for drive systems.

Echolds, E. F.↗

NASA NTRS1973

Investigation of fluctuations in angular velocity in magnetic memory devices

The fluctuations in the angular velocity of individual assemblies of a precision mechanical system were analyzed. The system was composed of an electric motor and a magnetic drum which were connected by a flexible coupling. A dynamic model was constructed which took into account the absence of torsion in the rigid shafts of the electric motor drive rotor and the magnetic drum. The motion was described by Lagrange differential equations of the second kind. Curves are developed to show the nature of amplitude fluctuation of the magnetic drum angular velocity at a specific excitation frequency. Additional curves show the amplitudes of fluctuation of the magnetic drum angular velocity compared to the quantity of damping at specific frequencies.

Meshkis, Y. A.↗

NASA NTRS1980

Near term hybrid passenger vehicle development program, phase 1

Missions for hybrid vehicles that promise to yield high petroleum impact were identified and a preliminary design, was developed that satisfies the mission requirements and performance specifications. Technologies that are critical to successful vehicle design, development and fabrication were determined. Trade-off studies to maximize fuel savings were used to develop initial design specifications of the near term hybrid vehicle. Various designs were "driven" through detailed computer simulations which calculate the petroleum consumption in standard driving cycles, the petroleum and electricity consumptions over the specified missions, and the vehicle's life cycle costs over a 10 year vehicle lifetime. Particular attention was given to the selection of the electric motor, heat engine, drivetrain, battery pack and control system. The preliminary design reflects a modified current compact car powered by a currently available turbocharged diesel engine and a 24 kW (peak) compound dc electric motor.

Source record↗

NASA NTRS1981

Selection of a pump-fed propulsion system for planetary exploration missions

A study has been conducted to select the most desirable pump-fed propellant feed system approach for planetary spacecraft. Four systems, including two battery powered and two gas generator driven systems, were considered. Complete propulsion system schematics were developed, including preliminary detailed design of both the electric motor and the gas turbine pump drives. Utilizing a Figure-of-Merit system which included consideration for reliability, development risk, complexity and growth potential as well as weight, the advanced battery powered electric motor drive system was selected for continued development at JPL.

Auslander, T. W.↗

NASA NTRS2019

Enabling Additive Manufacturing Technologies for Advanced Aero Propulsion Materials & Components

Additive manufacturing (AM) technologies are enabling for advanced high performance, propulsion component designs in electric motors1-2 and turbine engine systems in future electrified aircraft. AM offers significant benefits over conventional manufacturing to fabricate components that are more compact, lighter weight, geometrically complex, innovatively cooled, integrated, multi-material, and multifunctional. For turbine engine applications, silicon carbide (SiC) based composites are being pursued using binder jetting and laminated object manufacturing (LOM) for components such as shrouds, vanes, and recuperators. For electric motor applications, additive processes are being applied toward optimized component designs to include the housing, rotor, and stators with 3-D printing and wire imbedded coils and with direct printed 3-phase coils. The electrical conductivity of silver conductor coils optimized by evaluating alternate sintering methods and additions of graphene and carbon nanostructures will be presented. Potential benefits of new electric motor components in improving temperature capability, efficiency, and power density for reductions in energy consumption and emissions will be discussed.

Halbig, Michael C.↗

NASA NTRS2018

Dynamic Analysis of the hFan, a Parallel Hybrid Electric Turbofan Engine

NASA and a variety of aerospace industry stakeholders are investing in conceptual studies of electrified aircraft, including parallel hybrid electric aircraft such as the Subsonic Ultra Green Aircraft Research (SUGAR) Volt. At this point, little of the work published in the literature has examined the transient behavior of the turbomachinery in these systems. This paper describes a control system built around the hFan, the parallel hybrid electric turbofan engine designed for the SUGAR Volt concept aircraft. This control system is used to show that the hFan, running with its baseline concept of operations, is capable of transient operation throughout the envelope. The design parameters of this controller are varied to assess the amount of operability margin built into the engine design, and whether this margin can be reduced to enable more aggressive designs, that may feature better fuel economy. Further, studies are performed as parameters for the hFan electric motor are varied to determine how the motor impacts the engine's need for transient operability margin. The studies suggest that the engine may be redesigned with as much as a 3% reduction in high pressure compressor stall margin. It was also demonstrated that appropriate design and control of the electric motor may be able to buy an additional 0.5% stall margin reduction or a turbine inlet temperature reduction of 35 degR, as tested at the sea-level static condition.

turboelectric↗

NASA NTRS2018

Dynamic Analysis of the hFan, a Parallel Hybrid Electric Turbofan Engine

SUGAR Volt↗

NASA NTRS1977

Research on battery-operated electric road vehicles

Mathematical analysis of battery-operated electric vehicles is presented. Attention is focused on assessing the influence of the battery on the mechanical and dynamical characteristics of dc electric motors with series and parallel excitation, as well as on evaluating the influence of the excitation mode and speed control system on the performance of the battery. The superiority of series excitation over parallel excitation with respect to vehicle performance is demonstrated. It is also shown that pulsed control of the electric motor, as compared to potentiometric control, provides a more effective use of the battery and decreases the cost of recharging.

Varpetian, V. S.↗

NASA NTRS2019

Additive Manufacturing Technologies for Aerospace Applications

An overview will be provided on NASA GRC activities in additive manufacturing (AM) technology development for advanced high performance, propulsion component designs in electric motors and turbine engine systems in future electrified aircraft. AM offers significant benefits over conventional manufacturing to fabricate components that are more compact, lighter weight, geometrically complex, innovatively cooled, integrated, multi-material, and multifunctional. For turbine engine applications, silicon carbide (SiC) based composites are being pursued using binder jetting. For electric motor applications, additive processes are being applied toward optimized component designs to include the housing, rotor, and stators with 3-D printing and wire imbedded coils and with direct printed 3-phase coils. The will be an emphasis on capabilities in additive manufacturing.

Halbig, Michael C.↗

NASA NTRS2022

X-57 Mod II Avionics Power Analysis

The X-57 Mod II Avionics Power Analysis was developed to provide the design requirements for the X-57 Avionics Power System. In the Mod II configuration, the two stock Tecnam P2006T Rotax engines are replaced with two electric motors. A high voltage traction battery (460 VDC nominal) supplies power for the motors. The Mod II avionics power design uses the stock Tecnam avionics power architecture as a baseline. The stock Tecnam power system utilizes three 12 VDC power sources, a battery and two alternators, to provided redundant avionics power. This redundancy was preserved in the X-57 avionics power architecture. A block diagram of the X-57 avionics system can be found in the “Mod II Architecture” worksheet of this documents. Since the X-57 electric motors do not have alternators or generators, two 13.8V DC Converters were added to replace the stock Tecnam alternators. Input power to these DC Converters is provide by the high voltage traction battery. The Tecnam stock lead acid battery was replaced with a Lithium Iron Phosphate (LiFePO4) battery. The Mod II Avionics Power Analysis provided the power requirements for the two 13.8V DC converters and the Lithium Iron Phosphate battery. Power requirement estimates for each subsystem used in this analysis were provided by manufacturer specifications, measured in the laboratory or provided by the subsystem design engineer. Typical power requirements and maximum power requirements were provided for each subsystem. The Mod II Avionics Power Systems consists of seven 13.8 VDC buses, two 28 VDC Buses and two 23 VDC buses. The avionics power requirements for Mod III configuration are the same as Mod II. The Mod III configuration replaces the stock Tecnam wing with a carbon fiber wing that is optimized for cruise conditions. The motors are located on the wingtips. The Mod IV Avionics Power Analysis is a separate analysis and is document number ANLYS-CEPT-032.

Keith Harris↗

NASA NTRS1997

Hybrid Turbine Electric Vehicle

Hybrid electric power trains may revolutionize today's ground passenger vehicles by significantly improving fuel economy and decreasing emissions. The NASA Lewis Research Center is working with industry, universities, and Government to develop and demonstrate a hybrid electric vehicle. Our partners include Bowling Green State University, the Cleveland Regional Transit Authority, Lincoln Electric Motor Division, the State of Ohio's Department of Development, and Teledyne Ryan Aeronautical. The vehicle will be a heavy class urban transit bus offering double the fuel economy of today's buses and emissions that are reduced to 1/10th of the Environmental Protection Agency's standards. At the heart of the vehicle's drive train is a natural-gas-fueled engine. Initially, a small automotive engine will be tested as a baseline. This will be followed by the introduction of an advanced gas turbine developed from an aircraft jet engine. The engine turns a high-speed generator, producing electricity. Power from both the generator and an onboard energy storage system is then provided to a variable-speed electric motor attached to the rear drive axle. An intelligent power-control system determines the most efficient operation of the engine and energy storage system.

Viterna, Larry A.↗

NASA NTRS2009

Hydrogen Fuel System Design Trades for High-Altitude Long-Endurance Remotely- Operated Aircraft

Preliminary design trades are presented for liquid hydrogen fuel systems for remotely-operated, high-altitude aircraft that accommodate three different propulsion options: internal combustion engines, and electric motors powered by either polymer electrolyte membrane fuel cells or solid oxide fuel cells. Mission goal is sustained cruise at 60,000 ft altitude, with duration-aloft a key parameter. The subject aircraft specifies an engine power of 143 to 148 hp, gross liftoff weight of 9270 to 9450 lb, payload of 440 lb, and a hydrogen fuel capacity of 2650 to 2755 lb stored in two spherical tanks (8.5 ft inside diameter), each with a dry mass goal of 316 lb. Hydrogen schematics for all three propulsion options are provided. Each employs vacuum-jacketed tanks with multilayer insulation, augmented with a helium pressurant system, and using electric motor driven hydrogen pumps. The most significant schematic differences involve the heat exchangers and hydrogen reclamation equipment. Heat balances indicate that mission durations of 10 to 16 days appear achievable. The dry mass for the hydrogen system is estimated to be 1900 lb, including 645 lb for each tank. This tank mass is roughly twice that of the advanced tanks assumed in the initial conceptual vehicle. Control strategies are not addressed, nor are procedures for filling and draining the tanks.

Millis, Marc G.↗