SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
A simple siphon method is described for determining the resistivities of thin heat pipe wicks as a function of the pressure difference between the liquid in the wick and the vapor above it. The method was applied to wicks of one layer and two layers of 100 mesh (40 per centimeter) stainless steel screens diffusion bonded to stainless steel substrates. Some possible improvements in the method are suggested.
The high temperature properties of boron/aluminum composites, fabricated by an air diffusion bonding technique utilizing vacuum-bonded monolayer tape are reported. Seventeen different combinations of matrix alloy, reinforcement diameter, reinforcement volume percent, angle-ply and matrix enhancement (i.e. titanium cladding and interleaves) were fabricated, inspected, and tested. It is shown that good to excellent mechanical properties could be obtained for air-bonded boron/aluminum composites and that these properties did not decrease significantly up to a test temperature of at least 260 C. Composites made with 8 mil B/W fiber show a much greater longitudinal strength dependence on volume percent fiber than composites made with 5.6 mil fiber. The addition of titanium caused difficulties in composite bonding and yielded composites with reduced strength.
Flightworthy primary structural panels were designed, fabricated, and tested to investigate two advanced fabrication methods for titanium alloys. Skin-stringer panels fabricated using the weldbraze process, and honeycomb-core sandwich panels fabricated using a diffusion bonding process, were designed to replace an existing integrally stiffened shear panel on the upper wing surface of the NASA YF-12 research aircraft. The investigation included ground testing and Mach 3 flight testing of full-scale panels, and laboratory testing of representative structural element specimens. Test results obtained on full-scale panels and structural element specimens indicate that both of the fabrication methods investigated are suitable for primary structural applications on future civil and military supersonic cruise aircraft.
The requirements and opportunities for technological development in transport aircraft of the next generation are reviewed, focusing primarily on conventional, subsonic aircraft. Advances in computational aerodynamics and computer-aided design and manufacturing (in numerically controlled processes) are noted as well as improved wind tunnel testing and drag reduction techniques. Advances in aeroelasticity prediction have made it possible to use flexible, high-aspect-ratio wings without large weight penalties. Weight reduction may be achieved by the use of composite aircraft structures and superplastic forming combined with diffusion bonding, however composites require improvement in manufacturing techniques and mechanical properties in order to gain general acceptance. Propulsion systems can be improved in engine fuel efficiency, control, durability, environmental compatibility (exhaust and noise emissions), and fuel specifications. In avionics, due to the growth of low-cost, miniaturized packages, opportunities exist in the fields of digital controls, navigation, guidance and communication. Applications of new technologies to various aspects of flight safety are also outlined.
Two studies are described in which CAD methods are used for preliminary design of advanced earth-to-orbit transport wings. The first structural concept was a multilayer honeycomb wing composed of diffusion-bonded Inconel 718; the second concept (in which structural simplicity was sought) involved a honeycomb sandwich wing, for which only a leading edge and trailing edge spar were used. Some new technologies applicable to advanced wing designs are briefly discussed.
The superplastically formed diffusion-bonded (SPF/DB) program has developed successfully and far enough to recommend that a major structural program to validate the weight and cost of SPF/DB sandwich titanium structure should be initiated. The NASA Langley study of wing and fuselage SPF/DB sandwich panels shows that this process is potentially structurally efficient. The Douglas SPF/DB expanded sandwich process that utilizes a welded core sheet that expands to face sheets proves to be very efficient. The theoretical weight optimization design charts for the wing and fuselage concepts were validated by small-scale tests. Mnay design applications were fabricated. Projecting the results of an SPF/DB sandwich airframe structure to a MDC AST design shows significant weight and cost savings. A 6 percent lower direct operating cost was calculated. A growth AST utilizing composites, metal matrices, and SPF/DB sandwich shows future promise for a post-1990 technology readiness. Titanium SPF/DB sandwich, compared to presently available aluminum structure, is superior for application to a Mach 2.2 supersonic transport.
Research and development programs to develop high-strength aluminum alloys and low-cost materials and fabrication techniques for titanium alloys are being conducted. Thirteen aluminum alloy compositions are being evaluated. A section of a production component was fabricated using superplastic forming and diffusion bonding (SPF/DB) and fabrication studies are being conducted on three low temperature forming beta titanium alloys. Cost studies indicate substantial structural cost reduction potentials resulting from the use of both aluminum alloys and low-cost titanium fabrication techniques. Lowest overall costs are indicated for a composite/aluminum or composite titanium structure.
The significant technology items of the Concorde and the conceptual MCD baseline advanced supersonic transport are compared. The four major improvements are in the areas of range performance, structures (materials), aerodynamics, and in community noise. Presentation charts show aerodynamic efficiency; the reoptimized wing; low scale lift/drag ratio; control systems; structural modeling and analysis; weight and cost comparisons for superplasticity diffusion bonded titanium sandwich structures and for aluminum brazed titanium honeycomb structures; operating cost reduction; suppressor nozzles; noise reduction and range; the bicone inlet; a market summary; environmental issues; high priority items; the titanium wing and fuselage test components; and technology validation.
This paper presents the results of recent Douglas Aircraft Company integration studies for an advanced supersonic transport. The studies include technology improvements such as superplastic formed and diffusion-bonded titanium sandwich primary structure, composite secondary structure, bicone engine inlet, improved mechanical suppressors based on flight test data, improved aerodynamic efficiency based on wind tunnel test data, and updated performance for both variable-cycle and low-bypass-ratio engines. Technology development requirements for an economically viable and environmentally acceptable advanced supersonic transport are defined through these studies. A new Douglas Aircraft Company baseline supersonic transport designed to carry 350 passengers is defined for cost comparisons.
A method is described for fabricating curved T1-6Al-4V multiwall panels having a single radius of curvature of 30.5 cm (12 inches). A panel 30.5 x 30.5 x 1.7 cm (12 x 12 x .688 inch) having 4 dimpled sheets, 5 undimpled sheets, and stepped side closures was designed, fabricated and delivered for evaluation. Tool design for skin and dimpled sheet forming are described as well as layup and liquid interface diffusion bonding.
Skin friction and profiles of mean velocity, axial and normal turbulence intensity, and Reynolds stress in the untripped boundary layer were measured directly on a large diameter, axisymmetric body with: (1) a smooth, solid surface; (2) a sandpaper-roughened, solid surface; (3) a sintered metal, porous surface; (4) a smooth, perforated titanium surface; (5) a rough solid surface made of fine, diffusion bonded screening, and (6) a rough, porous surface of the same screening. Results obtained for each of these surfaces are discussed. It is shown that a rough, porous wall simply does not influence the boundary layer in the same way as a rough solid wall. Therefore, turbulent transport models for boundary layers over porous surfaces either with or without injection or suction, must include both surface roughness and porosity effects.
Noise and economic characteristics were obtained for an advanced supersonic transport concept that utilized wing body blending, a double bypass variable cycle engine, superplastically formed and diffusion bonded titanium in both the primary and secondary structures, and an alternative interior arrangement that provides increased seating capacity. The configuration has a cruise Mach number of 2.62, provisions for 290 passengers, a mission range of 8.19 Mm (4423 n.mi.), and an average operating cruise lift drag ratio of 9.23. Advanced operating procedures, which have the potential to reduce airport community noise, were explored by using a simulator. Traded jet noise levels of 105.7 and 103.4 EPNdB were obtained by using standard and advanced takeoff operational procedures, respectively. A new method for predicting lateral attenuation was utilized in obtaining these jet noise levels.
The NASA-sponsored Energy Efficient Engine (E3) Program, which is now in its fourth year, is assessed from the viewpoint of one of its research contractors. Attention is given to the development status of the shroudless fan, segmented combustor and exhaust mixer components which are encompassed by the program. The shroudless fan blades are two-thirds hollow for lightness, and are fabricated by means of plies and cores subjected to hot isostatic pressing diffusion bonding. The combustor's segmented liner is cast from turbine blade materials. Exhaust mixer flow visualization tests are described. Consideration is given to the effects of integrating the technology described with the low and high pressure advanced turbines whose development is also part of the E3 program.
The feasibility of fabricating and processing liquid metal heat pipes in a low mass honeycomb sandwich panel configuration for application on the NASA Langley airframe-integrated Scramjet engine was investigated. A variety of honeycomb panel facesheet and core-ribbon wick concepts was evaluated within constraints dictated by existing manufacturing technology and equipment. The chosen design consists of an all-stainless steel structure, sintered screen facesheets, and two types of core-ribbon; a diffusion bonded wire mesh and a foil-screen composite. Cleaning, fluid charging, processing, and process port sealing techniques were established. The liquid metals potassium, sodium and cesium were used as working fluids. Eleven honeycomb panels 15.24 cm X 15.24 cm X 2.94 cm were delivered to NASA Langley for extensive performance testing and evaluation; nine panels were processed as heat pipes, and two panels were left unprocessed.
The wind tunnel models and instrumentation used as well as data reduction and error analysis techniques employed are described for an experimental study conducted to measure directly skin friction and obtain profiles of mean velocity, axial and normal turbulence intensity, and Reynolds stress in the untripped boundary on a large diameter axisymmetric body. Results are given for such a body with a (1) smooth, solid surface; (2) a sandpaper roughened, solid surface; (3) a sintered metal, porous surface; (4) a ""smooth'' performated titanium surface; (5) a rough, solid surface made of fine diffusion bonded screening; and (6) a rough, porous surface made of the same screening. The roughness values were in low range (k+ 5 to 7) just above what is normally considered ""hydraulically smooth''. Measurements were taken at several axial locations and tow or normal stream freestream velocities, 45.1 m/sec and 53.5 m/sec.
Mach 5 cruise research conducted by NASA is related to aerodynamics, propulsion, and structures. The study of structures includes the propulsion system, fuselage, and wings. Various studies have shown that the achievement of adequate range is largely dependent on a low structural mass fraction. The present investigation is concerned with a study of two wing structure configurations for Mach 5 aircraft. An uprated version (Ti-6242 replacing B-120 titanium) of the YF-12/SR-71 wing structure is considered. The B-120 titanium structure represents the current art of high speed aircraft wing structures. The YF-12 wing structure was designed about 20 years ago when the analytical methods for calculating thermal stresses were limited. The second wing structural configuration studied in the present investigation also used Ti-6242 materials but replaced the corrugated-beaded panels with diffusion bonded honeycomb-core sandwich panels, and replaced the z-stiffened shear webs with sine-wave stiffened shear webs.
The impact of variable sweep wing technology with relaxed static stability requirements on a supersonic-cruise executive jet with transatlantic range was assessed. The baseline vehicle utilized modified, current-technology engines and titanium structures produced with superplastic forming and diffusion bonding; this vehicle meets study requirements for both supersonic-cruise and low-speed characteristics. The baseline concept has a ramp weight of 64,500 pounds with a crew of two and eight passengers. Its Mach 2.0 cruise range is nearly 3,500 nautical miles; its Mach 0.9 cruise range is over 5,000 nautical miles. Takeoff, landing, and balanced field length requirements were calculated for a composite variant and are all less than 5,000 feet.
Several silicon-carbide fiber reinforced titanium matrix composite systems were investigated to determine composite degradation mechanisms and to develop techniques to minimize loss of mechanical properties during fabrication and in service. Emphasis was on interface control by fiber or matrix coatings. Fibers and matrix materials were sputter coated with various metals to determine the effects of the coatings on basic fiber properties, fiber-matrix interactions, and on composite properties. The effects of limited variations in fabrication temperature on composite properties were determined for composites consolidated by standard press-diffusion-bonding techniques.