Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “DSD”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8
All sourcesNASA NTRSDOE OSTI
NASA NTRS2017

Optical Extinction Measurements of Laser Side-Scatter During Tropical Storm Colin

A side-scatter imaging (SSI) technique using a 447 nm, 500 mW laser and a Nikon D80 camera was tested at Kennedy Space Center, Florida during the passing of a rain band associated with Tropical Storm Colin. The June 6, 2016, 22:00 GMT rain event was intense but short-lived owing to the strong west-to-east advection of the rain band. An effort to validate the optical extinction measurement was conducted by setting up a line of three tipping rain gauges along an 80 m east-west path and below the laser beam. Differences between tipping bucket measurements were correlated to the extinction coefficient profile along the lasers path, as determined by the SSI measurement. In order to compare the tipping bucket to the optical extinction data, a Marshall-Palmer DSD model was assumed. Since this was a daytime event, the laser beam was difficult to detect in the camera images, pointing out an important limitation of SSI measurements: the practical limit of DSD density that can be effectively detected and analyzed under daylight conditions using this laser and camera, corresponds to a fairly moderate rainfall rate on the order of 20 mmh (night measurements achieve a much improved sensitivity). The SSI analysis model under test produced promising results, but in order to use the SSI method for routine meteorological studies, improvements to the math model will be required.

optical extinction↗
NASA NTRS2016

Impact of Scattering Model on Disdrometer Derived Attenuation Scaling

NASA Glenn Research Center (GRC), the Air Force Research Laboratory (AFRL), and the Politecnico di Milano (POLIMI) are currently entering the third year of a joint propagation study in Milan, Italy utilizing the 20 and 40 GHz beacons of the Alphasat TDP5 Aldo Paraboni scientific payload. The Ka- and Q-band beacon receivers were installed at the POLIMI campus in June of 2014 and provide direct measurements of signal attenuation at each frequency. Collocated weather instrumentation provides concurrent measurement of atmospheric conditions at the receiver; included among these weather instruments is a Thies Clima Laser Precipitation Monitor (optical disdrometer) which records droplet size distributions (DSD) and droplet velocity distributions (DVD) during precipitation events. This information can be used to derive the specific attenuation at frequencies of interest and thereby scale measured attenuation data from one frequency to another. Given the ability to both predict the 40 GHz attenuation from the disdrometer and the 20 GHz timeseries as well as to directly measure the 40 GHz attenuation with the beacon receiver, the Milan terminal is uniquely able to assess these scaling techniques and refine the methods used to infer attenuation from disdrometer data.In order to derive specific attenuation from the DSD, the forward scattering coefficient must be computed. In previous work, this has been done using the Mie scattering model, however, this assumes a spherical droplet shape. The primary goal of this analysis is to assess the impact of the scattering model and droplet shape on disdrometer derived attenuation predictions by comparing the use of the Mie scattering model to the use of the T-matrix method, which does not assume a spherical droplet. In particular, this paper will investigate the impact of these two scattering approaches on the error of the resulting predictions as well as on the relationship between prediction error and rain rate.

statistics↗
NASA NTRS2020

Comparison of Raindrop Size Distribution between NASA’s S-Band Polarimetric Radar and Two-Dimensional Video Disdrometers

The ground-based-radar-derived raindrop size distribution (DSD) parameters—mass-weighted drop diameter Dmass and normalized intercept parameter NW—are the sole resource for direct validation of the National Aeronautics and Space Administration (NASA) Global Precipitation Measurement (GPM) mission Core Observatory satellite-based retrieved DSD. Both Dmass and NW are obtained from radar-measured reflectivity ZH and differential reflectivity ZDR through empirical relationships. This study uses existing relationships that were determined for the GPM ground validation (GV) program and directly compares the NASA S-band polarimetric radar (NPOL) observables of ZH and ZDR and derivedDmass and NW with those calculated by two-dimensional video disdrometer (2DVD). The joint NPOL and 2DVD datasets were acquired during three GPM GV field campaigns conducted in eastern Iowa, southern Appalachia, and western Washington State. The comparative study quantifies the level of agreement for ZH, ZDR, Dmass, and log(NW) at an optimum distance (15–40 km) from the radar as well as at distances greater than 60 km from radar and over mountainous terrain. Interestingly, roughly 10%–15% of the NPOL ZH–ZDR pairs were well outside the envelope of 2DVD-estimated ZH–ZDR pairs. The exclusion of these pairs improved the comparisons noticeably.

Ali Tokay↗
NASA NTRS2020

Development and Evaluation of the Raindrop Size Distribution Parameters for the NASA Global Precipitation Measurement Mission Ground Validation Program

The National Aeronautics and Space Administration Global Precipitation Measurement (GPM) mission ground validation program uses dual-polarization radar moments to estimate raindrop size distribution (DSD) parameters, the mass-weighted mean drop diameter Dmass, and normalized intercept parameter NW, to validate the GPM Core Observatory–derived DSD parameters. The disdrometer-based Dmass and NW are derived through empirical relationships between Dmass and differential reflectivity ZDR, and between NW, reflectivity ZH, and Dmass. This study employs large datasets collected from two-dimensional video disdrometers (2DVD) during six different field studies to derive the requisite empirical relationships. The uncertainty of the derived Dmass(ZDR) relationship is evaluated through comparisons of 2DVD-calculated and ZDR-estimated Dmass, where ZDR is calculated directly from 2DVD observations. Similarly, the uncertainty of the NW(ZH, Dmass) relationship is evaluated through 2DVD-calculated and Dmass and ZH-estimated NW, where Dmass and ZH are directly calculated from 2DVD observations. This study also presents the sensitivity of Dmass(ZDR) relationships to climate regime and to disdrometer type after developing three additional Dmass(ZDR) relationships from second-generation Particle Size Velocity (PARSIVEL2) disdrometer (P2) observations collected in the Pacific Northwest, in Iowa, and at Kwajalein Atoll in the tropical Pacific Ocean. The application of P2-derived Dmass(ZDR) relationship based on precipitation in the northwestern United States to P2 observations collected over the tropical ocean resulted in the highest error among comparisons of the three datasets.

Ali Tokay↗
NASA NTRS2020

Comparison of Raindrop Size Distribution between NASA's S-Band Polarimetric Radar and Two-Dimensional Video Disdrometers

The ground-based-radar-derived raindrop size distribution (DSD) parameters—mass-weighted drop diameter D mass and normalized intercept parameter NW—are the sole resource for direct validation of the National Aeronautics and Space Administration (NASA) Global Precipitation Measurement (GPM ) mission Core Observatory satellite-based retrieved DSD. Both D mass and NW are obtained from radar-measured reflectivity Z Hand differential reflectivity ZDR through empirical relationships. This study uses existing relationships that were determined for the GPM ground validation (GV) program and directly compares the NASA S-band polarimetric radar (NPOL) observables of Z Hand Z DR and derived D mass and NW with those calculated by two-dimensional video disdrometer (2DVD). The joint NPOL and 2DVD datasets were acquired during three GPM GV field campaigns conducted in eastern Iowa, southern Appalachia, and western Washington State. The comparative study quantifies the level of agreement for ZH, ZDR, D mass, and log (NW) at an optimum distance (15–40 km) from the radar as well as at distances greater than 60 km from radar and over mountainous terrain. Interestingly, roughly 10%–15% of the NPOLZH–Z DR pairs were well outside the envelope of 2DVD-estimatedZH–Z DR pairs. The exclusion of these pairs improved the comparisons noticeably.

Ali Tokay↗
NASA NTRS2020

Drop Size Distribution Measurements in Outer Rainbands of Hurricane Dorian at the NASA Wallops Precipitation-Research Facility

Hurricane rainbands are very efficient rain producers, but details on drop size distributions are still lacking. This study focuses on the rainbands of hurricane Dorian as they traversed the densely instrumented NASA precipitation-research facility at Wallops Island, VA, over a period of 8 h. Drop size distribution (DSD) was measured using a high-resolution meteorological particle spectrometer (MPS) and 2D video disdrometer, both located inside a double-fence wind shield. The shape of the DSD was examined using double-moment normalization, and compared with similar shapes from semiarid and subtropical sites. Dorian rainbands had a superexponential shape at small normalized diameter values similar to those of the other sites. NASA’s S-band polarimetric radar performed range height-indicator (RHI) scans over the disdrometer site, showing some remarkable signatures in the melting layer (bright-band reflectivity peaks of 55 dBZ, a dip in the copolar correlation to 0.85 indicative of 12–15 mm wet snow, and a staggering reflectivity gradient above the 0 °C level of −10 dB/km, indicative of heavy aggregation). In the rain layer at heights < 2.5 km, polarimetric signatures indicated drop break-up as the dominant process, but drops as large as 5 mm were detected during the intense bright-band period.

Merhala Thurai↗
NASA NTRS2016

A Possible Explanation for the Z-R Parameter Inconsistency when Comparing Stratiform and Convective Rainfall

The well-known Z-R power law Z A R(sup b) uses two parameters, A and b, in order to relate rainfall rate R to measured weather radar reflectivity Z. A common method used by researchers is to compute Z and R from disdrometer data and then extract the A-b parameter pair from a log-linear line fit to a scatter plot of Z-R pairs. Even though it may seem far more truthful to extract the parameter pair from a fit of radar Z(sub R) versus gauge rainfall rate R(sub G), the extreme difference in spatial and temporal sampling volumes between radar and rain gauge creates a slew of problems that can generally only be solved by using rain gauge arrays and long sampling averages. Disdrometer derived A-b parameters are easily obtained and can provide information for the study of stratiform versus convective rainfall. However, an inconsistency appears when comparing averaged A-b pairs from various researchers. Values of b range from 1.26 to 1.51 for both stratiform and convective events. Paradoxically the values of A fall into three groups: 150 to 200 for convective; 200 to 400 for stratiform; and 400 to 500 again for convective. This apparent inconsistency can be explained by computing the A-b pair using the gamma DSD coupled with a modified drop terminal velocity model, v(D) alpha D(sup beta) - w, where w is a somewhat artificial constant vertical velocity of the air above the disdrometer. This model predicts three regions of A, corresponding to w less than 0, w = 0, and w greater than 0, which approximately matches observed data.

gamma DSD↗
NASA NTRS1996

A New Parametrization of the Rain Drop Size Distribution

This paper revisits the problem of finding a parametric form for the rain drop size distribution (DSD) which 1) is an appropriate model for tropical rainfall, and 2) involves statistically independent parameters. Using TOGA/COARE data, we derive a parametrization which meets these criteria. This new parametrization is an improvement on the one that was derived in [3] using TRMM ground truth data from Darwin, Australia. The new COARE data allows us to verify that the spatial variability fo the two

rain↗
DOE OSTI2017

Physical Interpretation of Mixing Diagrams: Interpretation of Mixing Diagrams

Type of mixing at cloud edges is often determined by means of mixing diagrams showing the dependence of normalized cube of the mean volume radius on the dilution level. The mixing diagrams correspond to the final equilibrium state of mixing between two air volumes. While interpreting in situ measurements, scattering diagrams are plotted in which normalized droplet concentration is used instead of dilution level. Utilization of such scattering diagrams for interpretation of in situ observations faces significant difficulties and often leads to misinterpretation of the mixing process and to uncertain conclusions concerning the mixing type. In this study we analyze the scattering diagrams obtained by means of a Lagrangian-Eulerian model of a stratocumulus cloud. The model consists of 2,000 interacting Largangian parcels which mix with their neighbors during their motion in the atmospheric boundary layer. In the diagram, each parcel is denoted by a point. Changes of microphysical parameters of the parcel are represented by movements of the point in the scattering diagram. The method of plotting the scattering diagrams using the model is in many aspects similar to that used in in situ measurements. It is shown that a scattering diagram shows snapshots of a transient mixing process. The location of points in the scattering diagrams reflects largely the history and the origin of air parcels. Location of points on scattering diagram characterizes intensity of entrainment, and different parameters of droplet size distributions (DSDs) like concentration, mean volume (or effective) radius, and DSD width.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2017

Rain retrieval from dual-frequency radar Doppler spectra: validation and potential for a midlatitude precipitating case-study

A recently developed technique retrieving the binned raindrop size distributions (DSDs) and air state parameters from ground-based K a and W-band radars Doppler spectra profiles is improved and applied to a typical midlatitude rain event. The retrievals are thoroughly validated against DSD observations of a 2D video disdrometer and independent X-band observations. Here for this case-study, profiles of rain rate, R, mean volume diameter and concentration parameter are retrieved, with low bias and standard deviations. In light rain (0.1 < R < 1 mm h -1 ), the radar reflectivities must be calibrated with a collocated disdrometer which introduces random errors due to sampling mismatch between the two instruments. The best performances are obtained in moderate rain (1 < R < 20 mm h -1 ) where the retrieval is providing self-consistent estimates of the absolute calibration and of the attenuation caused by antenna or radome wetness for both radars.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2023

Pathway for decarbonizing residential building operations in the US and China beyond the mid-century

With global carbon budget targets looming, residential buildings in top economies must become carbon neutral as soon as possible to reserve more emission space for emerging carbon-emitting economies. This study is the first to compare the operational decarbonization process of China’s and the United States (US) residential buildings from 2000 to 2060 by combining the end-use emission model with the decomposing structural decomposition (DSD) method and Monte Carlo simulation. The results show that from 2001 to 2020 China decarbonized 1544 mega-tons of carbon dioxide (MtCO 2 ) and the US decarbonized 1848 MtCO 2 . In the business-as-usual scenario, China will hit its emission peak in 2031 (±3) with 934 (±61) MtCO 2 , while the US will maintain a lock-in level of 736 (±133) MtCO 2 since the 2030s. In the decarbonization scenario, operational carbon neutrality for residential buildings in 2060 is promoted by an increase in clean power generation proportion, building-integrated power generation level, building electrification level, and a reduction in end-use energy intensity, which will contribute 34.4 %, 21.4 %, 14.3 %, and 29.9 % in China and 32.9 %, 33.1 %, 8.2 %, and 25.8 % in the US, respectively. Especially, building-integrated power generation in China only costs about 40 % of what it costs in the US. Besides, high-decarbonization strategies for residential building operations are proposed as references for governments to formulate targeted climate policies. Overall, this study offers data benchmarks for buildings’ carbon neutrality of top economies to further promote synergistic carbon neutrality with the buildings of emerging economies in the age of Post COP27.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2019

Calculation of supersaturation maximum and droplet concentration at cloud boundaries

Most parameterizations of droplet concentration at cloud base in cloud models are derived under the assumption that all droplets at the cloud base form by nucleation of dry CCN crossing the lifting condensation level in updraft. In this study, a novel method of calculation of the supersaturation maximum and droplet concentration at cloud base is described that takes into account the existence of liquid at the level of droplet nucleation. Liquid exists in haze particles, as well as in the form of cloud droplets and raindrops. It is shown that the presence of liquid water inside non-activated CCN, as well as of cloud droplets and raindrops substantially decreases supersaturation maximum in case of high aerosol concentration. The possible effect of the supersaturation maximum decrease on formation of DSD in clouds is discussed. The method can be also applied to calculation of supersaturation and droplet nucleation at cloud edges.

58 GEOSCIENCES↗
DOE OSTI2019

Surface evolution of synthetic bilgewater emulsion

Bilgewater is oil-in-water emulsion emitted from shipboard and it is a source of pollution to the ocean. Wastewater treatment needs fundamental knowledge of the bilgewater surface changes; however, limited information is available. We have reported the first surface characterization of synthetic bilgewater emulsion using time-of-flight secondary ion mass spectrometry (ToF-SIMS) coupled with optical microscopy. A NAVY synthetic bilgewater emulsion consisting of three oils and a detergent mixture is used as the synthetic bilgewater model. Both fresh and aged emulsion samples are analyzed to determine their droplet size distributions (DSDs) and surface chemical compositions. Our results show that fresh emulsions are largely mono-modal with hydrocarbon fragments as the main surface composition. Aged emulsions are also monomodal with slightly larger size. Both SIMS spectral comparison and Principal Component Analysis (PCA) show that some surfactant components appear on the fresh emulsion surface immediately while larger molecular weight components appear at the aged bilge droplet surface. Our results indicate that the oil-water interface evolves after emulsion droplet forms. More importantly, surface evolution not only changes the bilgewater DSD but also surface chemical composition and reactivity.

bilgewater, droplet size distribution, ToF-SIMS, s↗
DOE OSTI2020

Density Functionals for Hydrogen Storage: Defining the H2Bind275 Test Set with Ab Initio Benchmarks and Assessment of 55 Functionals

Efficient and high-capacity storage materials are indispensable for a hydrogen-based economy. In silico tools can accelerate the process of discovery of new adsorbent materials with optimal hydrogen adsorption enthalpies. Density functional theory is well-poised to become a very useful tool for enabling high-throughput screening of potential materials. In this work, we have identified density functional approximations that provide good performance for hydrogen binding applications following a two-pronged approach. First, we have compiled a data set (H2Bind275) that comprehensively represents the hydrogen binding problem capturing the chemical and mechanistic diversity in the binding sites encountered in hydrogen storage materials. We have also computed reference interaction energies for this data set using coupled-cluster theory. Second, we have assessed the performance of 55 density functional approximations for predicting H 2 interaction energies and have identified two hybrid density functionals (ωB97X-V and ωB97M-V), two double hybrid density functionals (DSD-PBEPBE-D3(BJ) and PBE0-DH), and one semilocal density functional (B97M-V) as the best performing ones. We have recommended the addition of empirical dispersion corrections to systematically underbinding density functionals such as revPBE, BLYP, and B3LYP for improvements in performance at negligible additional cost. We have also recommended the usage of the def2-TZVPP basis set as it represents a good compromise between accuracy and cost, limiting the finite basis set errors to less than 1 kJ/mol.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Assessment of Performance of Density Functionals for Predicting Potential Energy Curves in Hydrogen Storage Applications

We report the availability of accurate computational tools for modeling and simulation is vital to accelerate the discovery of materials capable of storing hydrogen (H 2 ) under given parameters of pressure swing and temperature. Previously, we compiled the H2Bind275 data set consisting of equilibrium geometries and assessed the performance of 55 density functionals over this data set (Veccham, S. P.; Head-Gordon, M. J. Chem. Theory Comput. 2020, 16, 4963-4982). As it is crucial for computational tools to accurately model the entire potential energy curve (PEC), in addition to the equilibrium geometry, we extended this data set with 389 new data points to include two compressed and three elongated geometries along 78 PECs for H 2 binding, forming the H2Bind78 × 7 data set. By assessing the performance of 55 density functionals on this significantly larger and more comprehensive H2Bind78 × 7 data set, we identified the best performing density functionals for H 2 binding applications: PBE0-DH, ωB97X-V, ωB97M-V, and DSD-PBEPBE-D3(BJ). The addition of Hartree-Fock exchange improves the performance of density functionals, albeit not uniformly throughout the PEC. We recommend the usage of ωB97X-V and ωB97M-V density functionals as they offer good performance for both geometries and energies. In addition, we also identified B97M-V and B97M-rV as the best semilocal density functionals for predicting H 2 binding energy at its equilibrium geometry.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Observed and Simulated Variability of Droplet Spectral Dispersion in Convective Clouds Over the Amazon

Abstract In this study, the variability of the spectral dispersion of droplet size distributions (DSDs) in convective clouds is investigated. Analyses are based on aircraft measurements of growing cumuli near the Amazon basin, and on numerical simulations of an idealized ice‐free cumulus. In cleaner clouds, the relative dispersion , defined as the ratio of the standard deviation to the mean value of the droplet diameter, is negatively correlated with the ratio of the cloud water content ( ) to the adiabatic liquid water content ( ), while no strong correlation between and is seen in polluted clouds. Bin microphysics numerical simulations suggest that these contrasting behaviors are associated with the effect of collision‐coalescence in cleaner clouds, and secondary droplet activation in polluted clouds, in addition to the turbulent mixing of parcels that experienced different paths within the cloud. Collision‐coalescence simultaneously broadens the DSDs and decreases , explaining the inverse relationship between and in cleaner clouds. Secondary droplet activation broadens the DSDs but has little direct impact on . The combination of a rather modest DSD broadening due to weak collision‐coalescence with enhanced droplet activation in both diluted and highly undiluted cloud regions may contribute to maintain a relatively uniform within polluted clouds. These findings can be useful for parameterizing the shape parameter ( ) of gamma DSDs in bulk microphysics cloud‐resolving models. It is shown that emulating the observed relationship improves the estimation of the collision‐coalescence rate in bulk microphysics simulations compared to the bin simulations.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2023

A Statistical Framework for Evaluating Rain Microphysics in Model Simulations and Disdrometer Observations

Abstract Statistical analyses of a large disdrometer data set and a diverse set of model simulations for convection using the Regional Atmospheric Modeling System were conducted, with the mutual goal of providing insights into precipitation formation and microphysical processes. We demonstrate that a two‐moment bulk microphysical model successfully captures the dominant observed modes of variability in rainfall related to rainfall intensity and raindrop size distributions. The model reproduced the general distribution of observed precipitation groups (PGs) derived from Principal Component Analysis. The multi‐variable analysis also uncovered some shortcomings in the model as well as limitations of the disdrometer data. The model solutions were constrained in their predicted drop size distributions (DSDs) due to the fixed DSD parameters assumed in a two‐moment microphysics scheme. A case study from the Mid‐latitude Continental Clouds and Convection Experiment field project demonstrated how model results can be used to contextualize the disdrometer observations which are limited in sample size, spatial coherence, and detection of small drops and low drop concentrations. The case study also showed that the spatial patterns of the statistically derived PGs revealed by the model are consistent with the hypothesized microphysical processes that determine surface rain DSDs. This work demonstrates how leveraging the strengths of observations and models together can improve our understanding and representation of rain microphysical processes.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2024

THz Radar Observations of Hydrometeors in a Spray Chamber

Abstract A THz radar, with its wide bandwidth, is capable of high‐resolution imaging down to the centimeter scale. In this study, a THz radar is applied to detect hydrometeors generated in a spray chamber. The observed backscattering signals show fluctuations at centimeter scales, indicating various hydrometeor distribution patterns along the radar beam. A co‐located High‐Speed Imaging (HSI) sensor is used to measure the Drop Size Distributions (DSD) in the spray chamber. The radar sampling beam is well aligned with the HSI probes, allowing an objective comparison between the remote sensing and in situ observations. In this study, the observed radar power is compared with the power estimated from the HSI measurements. Results show great consistency, with power difference smaller than 0.5 dB. This study demonstrates the feasibility and great potential of using a THz radar for ultra‐high‐resolution observations of clouds in a laboratory facility, and in the real atmosphere.

54 ENVIRONMENTAL SCIENCES↗