Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Current mode”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8
All sourcesNASA NTRSDOE OSTI
NASA NTRS1988

The excitation and damping of solar oscillations

The status of understanding of the excitation and damping of solar p-mode oscillations is reviewed. While a few simple statements can be made about the expected properties of p-modes, there is currently no complete theory which explains the observed mode amplitudes and linewidths. Evidence suggests that the p-modes cannot be overstable and therefore self-excited, but are instead probably stochastically excited by turbulent convection. The status of the latter model for exciting p-modes, and possible future directions are discussed.

Libbrecht, Ken G.↗
NASA NTRS2004

Advanced Diagnostic System on Earth Observing One

In this infusion experiment, the Livingstone 2 (L2) model-based diagnosis engine, developed by the Computational Sciences division at NASA Ames Research Center, has been uploaded to the Earth Observing One (EO-1) satellite. L2 is integrated with the Autonomous Sciencecraft Experiment (ASE) which provides an on-board planning capability and a software bridge to the spacecraft's 1773 data bus. Using a model of the spacecraft subsystems, L2 predicts nominal state transitions initiated by control commands, monitors the spacecraft sensors, and, in the case of failure, isolates the fault based on the discrepant observations. Fault detection and isolation is done by determining a set of component modes, including most likely failures, which satisfy the current observations. All mode transitions and diagnoses are telemetered to the ground for analysis. The initial L2 model is scoped to EO-1's imaging instruments and solid state recorder. Diagnostic scenarios for EO-1's nominal imaging timeline are demonstrated by injecting simulated faults on-board the spacecraft. The solid state recorder stores the science images and also hosts: the experiment software. The main objective of the experiment is to mature the L2 technology to Technology Readiness Level (TRL) 7. Experiment results are presented, as well as a discussion of the challenging technical issues encountered. Future extensions may explore coordination with the planner, and model-based ground operations.

Hayden, Sandra C.↗
NASA NTRS2013

Dual-Mode Combustor

A new dual-mode ramjet combustor used for operation over a wide flight Mach number range is described. Subsonic combustion mode is usable to lower flight Mach numbers than current dual-mode scramjets. High speed mode is characterized by supersonic combustion in a free-jet that traverses the subsonic combustion chamber to a variable nozzle throat. Although a variable combustor exit aperture is required, the need for fuel staging to accommodate the combustion process is eliminated. Local heating from shock-boundary-layer interactions on combustor walls is also eliminated.

Trefny, Charles J↗
NASA NTRS2017

Process for Operating a Dual-Mode Combustor

A new dual-mode ramjet combustor used for operation over a wide flight Mach number range is described. Subsonic combustion mode is usable to lower flight Mach numbers than current dual-mode scramjets. High speed mode is characterized by supersonic combustion in a free-jet that traverses the subsonic combustion chamber to a variable nozzle throat. Although a variable combustor exit aperture is required, the need for fuel staging to accommodate the combustion process is eliminated. Local heating from shock-boundary-layer interactions on combustor walls is also eliminated.

Trefny, Charles J.↗
NASA NTRS1985

Current collection from the space plasma through defects in solar array insulation

Operating high-voltage solar arrays in the space environment can result in anomalously large currents being collected through small insulation defects. Tests simulating the electron collection have shown that there are two major collection modes. The first involves current enhancement by means of a surface phenomenon involving secondary electron emission from the surrounding insulator. In the second mode, the current collection is enhanced by vaporization and ionization of the insulator material, in addition to the surface enhancement of the first mode. The electron collection due to surface enhancement (first mode) has been modeled. Using this model, simple calculations yield realistic predictions.

Robinson, R. S.↗
NASA NTRS1979

Optically isolated logarithmic nanoammeter capable of floating to 5 kilovolts

A logarithmic current-measuring instrument was developed to measure plasma coupling currents at a common mode voltage of 5 kilovolts. Positive or negative currents can be measured from 10 to the -9th power to .001 ampere direct current. Optical isolation is used to control input switching and to provide data referenced to ground potential. Analog meter readouts as well as zero to five volt outputs are provided for peripheral data collection. Six independent channels are provided. Three measure positive currents, and three measure negative currents. Although designed for vacuum operation, it can be used equally well in air to measure low currents at high common mode voltages.

Sturman, J. C.↗
NASA NTRSDate not supplied

Design Considerations of an Ascent Abort Monitor Algorithm for Use During Service Module Aborts

In support of human rating the Artemis missions, NASA's Orion program requires continuous abort coverage from liftoff through mission destination. During a portion of the ascent trajectory, the currently achievable abort mode is determined by an Orion algorithm using the onboard navigated vehicle state. This ascent abort monitor determines achievability for Orion's Mode 2 abort, Untargeted Abort Splashdown (UAS), by propagating the current vehicle state through ascent abort events to determine sufficient timing to perform the abort and to a ballistic touchdown point to approximate landing location relative to prescribed keep out boundaries. The algorithm was updated for Artemis 2 to allow the capability to limit loads for the majority of ascent. Performance of the algorithm has been demonstrated and verified through dispersed trajectory analysis with emulated flight software, unit testing, and hardware in the loop testing.

Esteban Guzman↗
NASA NTRS1981

Constricted double-heterojunction AlGaAs diode lasers - Structures and electrooptical characteristics

Constricted double-heterojunction (CDH) diode lasers are presented as a class of nonplanar-substrate devices for which the lasing cavity is on the least resistive electrical path between the contact and the substrate. Various CDH structures are discussed while treating such topics as liquid-phase epitaxy over channeled substrates, lateral mode control, and current control in nonplanar-substrate devices. Ridge-guide CDH lasers with positive-index lateral mode confinement provides single-mode CW operation to 7 mW/facet at room temperature and to 3 mW/facet at 150 C, while exhibiting light-current characteristics with second-harmonic distortions as low as -57 dB below the fundamental level. Semileaky guide CDH lasers with an asymmetric leaky cavity provide single-mode operation to 15-20 mW/facet CW, and to 50 mW/facet at 50% duty cycle.

Botez, D.↗
NASA NTRS1982

Studies of single-mode injection lasers and of quaternary materials. Volume 1: Single-mode constricted double-heterojunction AlGaAs diode lasers

Constricted double-heterojunction (CDH) lasers are presented as the class of single-mode nonplanar-substrate devices for which the lasing cavity is on the least resistive electrical path between the contact and the substrate. Various types of CDH structures are considered under three general topics: liquid-phase epitaxy over channeled substrates, lateral mode control, and current control in nonplanar-substrate devices. Ridge-guide CDH lasers have positive-index lateral-mode confinement and provide: single-mode CW operation to 7 mW/facet at room temperature and to 3 mW/facet at 150 C; light-current characteristics with second-harmonic distortion as low as -57 dB below the fundamental level; threshold-current temperature coefficients, as high as 375 C (pulsed) and 310 C (CW); constant external differential quantum efficiency to 100 C; and lasing operation to 170 C CW and 280 C pulsed. Semileakyguide CDH lasers have an asymmetric leaky cavity for lateral-mode confinement and provide single-mode operation to 15 to 20 mW/facet CW and to 50 mW/facet at 50% duty cycle. Modulation characteristics and preliminary reliability data are discussed.

Botez, D.↗
NASA NTRS2016

Performance, Facility Pressure Effects, and Stability Characterization Tests of NASA's Hall Effect Rocket with Magnetic Shielding Thruster

NASA's Hall Effect Rocket with Magnetic Shielding (HERMeS) 12.5 kW Technology Demonstration Unit-1 (TDU-1) has been the subject of extensive technology maturation in preparation for flight system development. Part of the technology maturation effort included experimental evaluation of the TDU-1 thruster with conducting and dielectric front pole cover materials in two different electrical configurations. A graphite front magnetic pole cover thruster configuration with the thruster body electrically tied to cathode, and an alumina front pole cover thruster configuration with the thruster body floating were evaluated. Both configurations were also evaluated at different facility background pressure conditions to evaluate background pressure effects on thruster operation. Performance characterization tests found that higher thruster performance was attained with the graphite front pole cover configuration with the thruster electrically tied to cathode. A total thrust efficiency of 68% and a total specific impulse of 2,820 s was demonstrated at a discharge voltage of 600 V and a discharge power of 12.5 kW. Thruster stability regimes were characterized with respect to the thruster discharge current oscillations and with maps of the discharge current-voltage-magnetic field (IVB). Analysis of TDU-1 discharge current waveforms found that lower normalized discharge current peak-to-peak and root mean square magnitudes were attained when the thruster was electrically floated with alumina front pole covers. Background pressure effects characterization tests indicated that the thruster performance and stability were mostly invariant to changes in the facility background pressure for vacuum chamber pressure below 1×10-5 Torr-Xe (for thruster flow rates of 20.5 mg/s). Power spectral density analysis of the discharge current waveforms showed that increasing the vacuum chamber background pressure resulted in a higher discharge current dominant breathing mode frequency. Finally, IVB maps of the TDU-1 thruster indicated that the discharge current became more oscillatory with higher discharge current peak-to-peak and RMS values with increased facility background pressure at lower thruster mass flow rates; thruster operation at higher flow rates resulted in less change to the thruster's IVB characteristics with elevated background pressure.

Electric Propulsion↗
NASA NTRS1983

Investigation of a pulsed electrothermal thruster

Exhaust velocity and thrust measurements are performed on a pulsed electrothermal thruster using polyethylene and Teflon propellants. The results verify theoretical predictions of equilibrium flow in the nozzle, resulting in substantial recovery of the energy of dissociation and ionization. The thruster is tested in an unsteady mode (15 micro sec current pulse and 15 cm discharge length) and in a quasi-steady mode (48 micro sec current pulse and 5 cm discharge length). All tests are run at 2 kJ. The exhaust velocity of the propellant mass exiting during the current pulse is measured with two types of time of flight probes, and the impulse bit is measured on a thrust stand. It is inferred from both theory and experiment that an additional amount of mass is exhausted after the pulse. The measured thrust to power ratio for polyethylene is T/P = 0.10 NkW at 21 km/sec in the unsteady mode, and T/P = .053 N/kW at 27 km/sec in the quasi-steady mode, where the velocities are measured by the time-of-flight probes. For Teflon propellant, T/P = .20 N/kW at 15 km/sec (unsteady mode) and 0.090 N/kW at 20 km/sec (quasi-steady mode). The discharge pressure and temperature predicted by a computational model for polyethylene are consistent with the measured thrust and discharge resistance.

Burton, R. L.↗
NASA NTRS1989

High-power single spatial mode AlGaAs channeled-substrate-planar semiconductor diode lasers for spaceborne communications

A high power single spatial mode channeled substrate planar AlGaAs semiconductor diode laser was developed. The emission wavelength was optimized at 860 to 880 nm. The operating characteristics (power current, single spatial mode behavior, far field radiation patterns, and spectral behavior) and results of computer modeling studies on the performance of the laser are discussed. Reliability assessment at high output levels is included. Performance results on a new type of channeled substrate planar diode laser incorporating current blocking layers, grown by metalorganic chemical vapor deposition, to more effectively focus the operational current to the lasing region was demonstrated. The optoelectronic behavior and fabrication procedures for this new diode laser are discussed. The highlights include single spatial mode devices with up to 160 mW output at 8600 A, and quantum efficiencies of 70 percent (1 W/amp) with demonstrated operating lifetimes of 10,000 h at 50 mW.

Connolly, J. C.↗
NASA NTRS2003

Analysis of ProSEDS Test of Bare-Tether Collection

NASA's tether experiment ProSEDS will be placed in orbit on board a Delta-II rocket to test bare-tether electron collection, deorbiting of the rocket second stage, and the system dynamic stability. ProSEDS performance will vary because ambient conditions change along the orbit and tether-circuit bulk elements at the cathodic end follow the step-by-step sequence for the current cycles of operating modes (open-circuit, shunt and resistor modes for primary cycles; shunt and battery modes for secondary cycles). In this work we discuss expected ProSEDS values of the ratio L,/L*, which jointly with cathodic bulk elements determines bias and current tether profiles; L, is tether length, and L* (changing with tether temperature and ionospheric plasma density and magnetic field) is a characteristic length gauging ohmic versus baretether collection impedances. We discuss how to test bare-tether electron collection during primary cycles, using probe measurements of plasma density, measurements of cathodic current in resistor and shunt modes, and an estimate of tether temperature based on ProSEDS orbital position at the particular cycle concerned. We discuss how a temperature misestimate might occasionally affect the test of bare-tether collection, and how introducing the battery mode in some primary cycles, for an additional current measurement, could obviate the need of a temperature estimate. We also show how to test bare-tether collection by estimating orbit-decay rate from measurements of cathodic current for the shunt and battery modes of secondary cycles.

Sanmartin, J. R.↗
NASA NTRS2019

Pulsed Plasma Acceleration Modeling in Detonation and Deflagration Modes

Gas-fed electromagnetic pulsed plasma accelerators discharge electrical energy into a gas to ionize and electromagnetically accelerate propellant in the domain. Efforts to model pulsed accelerators have either assumed that the discharge is short and completely transient, accelerating the gas by entraining it in a moving current sheet, or that the discharge is relatively long, establishing a stable quasi-steady current distribution pattern that accelerates a plasma flowing through it. There have been pulsed plasma accelerator tests that appear to fit somewhere between these two bounds, exhibiting some properties that are associated with the purely transient devices while also showing others that are associated with quasi-steady-state plasma acceleration. A model is presented based upon the premise that all pulsed plasma accelerators first form an accelerating current sheet (detonation mode accelerator). Depending upon the pulse length and the gas conditions in the dis- charge channel, the plasma sheet may reach the end of the accelerator before the discharge has completed a full half-cycle, wherein the proposed model transitions to a quasi-steady description of the acceleration process (deflagration mode accelerator). A review of the entire model is presented, highlighting improvements and upgrades implemented to aid in the stability of the numerical scheme used to model the gas flow in the channel and an improved treatment of current sheet mass shedding, which adds gas to the wake of the sheet. The assumptions employed to model the transition from detonation to deflagration mode are presented and used to generate solutions to the governing equations. The modeling of the deflagration-mode under the present assumptions results in very low deflagration impulse bits relative to those obtained at the end of the detonation mode, implying that the present assumptions and modeling of the deflagration mode may not represent a fruitful approach.

Polzin, Kurt A.↗
NASA NTRS2019

Pulsed Plasma Acceleration Modeling in Detonation and Deflagration Modes

Gas-fed electromagnetic pulsed plasma accelerators discharge electrical energy into a gas to ionize and electromagnetically accelerate propellant in the domain. Efforts to model pulsed accelerators have either assumed that the discharge is short and completely tran- sient, accelerating the gas by entraining it in a moving current sheet, or that the discharge is relatively long, establishing a stable quasi-steady current distribution pattern that accel- erates a plasma flowing through it. There have been pulsed plasma accelerator tests that appear to fit somewhere between these two bounds, exhibiting some properties that are associated with the purely transient devices while also showing others that are associated with quasi-steady-state plasma acceleration. A model is presented based upon the premise that all pulsed plasma accelerators first form an accelerating current sheet (detonation mode accelerator). Depending upon the pulse length and the gas conditions in the dis- charge channel, the plasma sheet may reach the end of the accelerator before the discharge has completed a full half-cycle, wherein the proposed model transitions to a quasi-steady description of the acceleration process (deflagration mode accelerator). A review of the entire model is presented, highlighting improvements and upgrades implemented to aid in the stability of the numerical scheme used to model the gas flow in the channel and an im- proved treatment of current sheet mass shedding, which adds gas to the wake of the sheet. The assumptions employed to model the transition from detonation to deflagration mode are presented and used to generate solutions to the governing equations. The modeling of the deflagration-mode under the present assumptions results in very low deflagration im- pulse bits relative to those obtained at the end of the detonation mode, implying that the present assumptions and modeling of the deflagration mode may not represent a fruitful approach.

Polzin, Kurt A.↗
NASA NTRS2003

Discharge Characterization of 40 cm-Microwave ECR Ion Source and Neutralizer

Discharge characteristics of a 40 cm, 2.45 GHz Electron Cyclotron Resonance (ECR) ion thruster discharge chamber and neutralizer were acquired. Thruster bulk discharge plasma characteristics were assessed using a single Langmuir probe. Total extractable ion current was measured as a function of input microwave power and flow rate. Additionally, radial ion current density profiles at the thruster.s exit plane were characterized using five equally spaced Faraday probes. Distinct low and high density operating modes were observed as discharge input power was varied from 0 to 200 W. In the high mode, extractable ion currents as high as 0.82 A were measured. Neutralizer emission current was characterized as a function of flow rate and microwave power. Neutralizer extraction currents as high as 0.6 A were measured.

Foster, John E.↗
NASA NTRS2010

Supersonic Free-Jet Combustion in a Ramjet Burner

A new dual-mode ramjet combustor concept intended for operation over a wide flight Mach number range is described. Subsonic combustion mode is similar to that of a traditional ram combustor which allows operation at higher efficiency, and to lower flight Mach numbers than current dual-mode scramjets. High speed mode is characterized by supersonic combustion in a free-jet that traverses the subsonic combustion chamber to a variable nozzle. The maximum flight Mach number of this scheme is governed largely by the same physics as its classical counterpart. Although a variable combustor exit aperture is required, the need for fuel staging to accommodate the combustion process is eliminated. Local heating from shock-boundary-layer interactions on combustor walls is also eliminated. Given the parallel nature of the present scheme, overall flowpath length is less than that of present dual-mode configurations. Cycle analysis was done to define the flowpath geometry for computational fluid dynamics (CFD) analysis, and then to determine performance based on the CFD results. CFD results for Mach 5, 8, and 12 flight conditions indicate stable supersonic free-jet formation and nozzle reattachment, thereby establishing the basic feasibility of the concept. These results also reveal the structure of, and interactions between the free-jet and recirculating combustion chamber flows. Performance based on these CFD results is slightly less than that of the constant-pressure-combustion cycle analysis primarily due to these interactions. These differences are quantified and discussed. Additional CFD results at the Mach 8 flight condition show the effects of nozzle throat area variation on combustion chamber pressure, flow structure, and performance. Calculations with constant temperature walls were also done to evaluate heat flux and overall heat loads. Aspects of the concept that warrant further study are outlined. These include diffuser design, ramjet operation, mode transition, loss mechanisms, and the effects of secondary flow for wall cooling and combustion chamber pressurization. Also recommended is an examination of system-level aspects such as weight, thermal management and rocket integration as well as alternate geometries and variable geometry schemes.

Trefny, Charles J.↗