Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “CeAs”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

FIDES-II/P2M Simulation Exercise on AN3 and AN10 bump tests: main results

This paper presents simulations of bump tests conducted as part of the P2M (Power to Melt and Maneuverability) project within the OECD/NEA FIDES-II framework (Framework for Irradiation Experiments). To prepare fuel performance codes for analyzing the P2M experiments, an international Simulation Exercise (SE) was initiated under the P2M project. The objective of this exercise was to model the AN3 and AN10 bump tests carried out in the 1980s at the DR3 reactor (3rd RISØ Fission Gas Project), during which instrumented fuel rodlets (equipped with thermocouples and pressure sensors) were subjected to prolonged power transients and power dips. The ongoing simulation exercise involves seven organizations from industry, research, and regulatory bodies, each using different fuel performance codes. This paper provides detailed descriptions of the test cases and simulation results from six fuel performance codes (ALCYONE, BISON, FAST, FEMAXI, FRAPCON, and TRANSURANUS), with a particular focus on fission gas release kinetics.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2025

Search for solar axions produced through the axion-electron coupling gae using a new GridPix detector at CAST

We present a search for solar axions produced through the axion-electron coupling (g ae ) using data from a novel 7-GridPix detector installed at the CERN Axion Solar Telescope (CAST). The detector, featuring ultra-thin silicon nitride windows and multiple veto systems, collected approximately 160 hours of solar tracking data between 2017–2018. Using machine learning techniques and the veto systems, we achieved a background rate of 1.06 × 10 −5 keV −1 cm −2 s −1 at a signal efficiency of about 80% in the 0.2 to 8 keV range. Analysis of the data yielded no significant excess above background, allowing us to set a new upper limit on the product of the axion-electron and axion-photon couplings of g ae · g aγ < 7.35 × 10 −23 GeV −1 at 95% confidence level for axion masses below 10 meV. This result improves upon the previous best helioscope limit and demonstrates the potential of GridPix technology for rare event searches. Additionally, we derived a limit on the axion-photon coupling of g aγ < 9.0 × 10 −11 GeV −1 at 95% CL, which, while not surpassing CAST’s best limit, provides complementary constraints on axion models.

Beyond Standard Model↗
DOE OSTI2025

All-alumina quarter-wave plate coatings fabricated by glancing angle deposition using serial bideposition

Anisotropic phase retarders, used in high power laser facilities to perform polarization smoothing, can be obtained by the glancing angle deposition (GLAD) coating process. Due to its high laser resistance, the coatings are mainly made of silica. Therefore, limited attention has been given to other dielectric materials. Here we present a study on alumina GLAD anisotropic coatings; a material with high laser resistance, higher birefringence and lower environmental sensitivity than silica. Since the anisotropy is related to the coatings microstructure through the deposition angle, samples were coated at angles varying from ± 68° to ± 82° using the serial bideposition technique. They were characterized by ellipsometry, polarimetry, spectrophotometry and electron microscopy. We showed that the highest birefringence is obtained at a deposition angle of ± 76° with an in-plane value of 0.053. Based on these results, a quarter-wave plate at 351 nm was designed as a multilayer with seven pairs of anisotropic layers deposited at ± 76° and isotropic layers deposited at 0°. The fabricated coating exhibited a uniform retardance of 88.51 ± 0.45 nm. The alumina GLAD wave plates presented here, open the door to new possibilities in the laser field and especially in the field of fusion energy.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Thermal and structural analysis of a new WEST reciprocating probe head with Titanium-Zirconium-Molybdenum armour material

The Tore Supra tokamak was transformed into an X-point divertor fusion device in the frame of the WEST (W-for tungsten-Environment in Steady-state Tokamak) project, launched in support of the ITER tungsten divertor strategy. WEST began operation in 2017. A new reciprocating probe head, equipped with a Titanium-Zirconium-Molybdenum (TZM) heat shield, was recently built and operated on WEST during the C9 Campaign in early 2024. TZM was chosen as armour material for its very good mechanical properties between 700 °C and 1400 °C. This material was already extensively used for probe heads and other plasma facing components on the Alcator C-Mod tokamak. Here, this paper presents the design of the new WEST probe head. It is equipped with tungsten filaments that can be heated to emit electrons and provide a direct measurement of the plasma potential in the scrape-off layer, and it is also equipped with a pair of Langmuir probes. The probe plunges vertically into the plasma, reaches its maximum dive depth, then returns to its protected resting position in about 0.25 s. Thermal loads are calculated using as input the thermal properties of TZM and radial profiles of the heat flux measured in the past by other reciprocating probes, and scaled upwards to the expected heat loads in the WEST scrape-off layer. An analytical estimation of Electromagnetic (EM) loads will also be presented, as well as a thermal and structural analysis of the probe for 15 cycles at maximum plunge depth. The probe is observed by an infrared camera. Comparisons between the heat flux deduced by the Langmuir probe and the infrared radiance of the probe housing during plasma exposure are finally presented.

Diagnostic↗
DOE OSTI2026

Analysis of RF Sheath-Driven Tungsten Erosion at RF Antenna in the WEST Tokamak

This study applies the newly developed STRIPE (Simulated Transport of RF Impurity Production and Emission) framework to analyze tungsten (W) erosion at RF antenna structures in the WEST tokamak. STRIPE integrates SolEdge3x for edge plasma backgrounds, COMSOL for 3D RF sheath potentials, RustBCA for sputtering yields, and GITR for impurity transport and ion energy–angle distributions. Building on prior work by Kumar et al. (2025) Nuclear Fusion, 65, 076039, which validated STRIPE for WEST ICRH discharge #57877, the present study provides a spatially resolved assessment of gross W erosion at both Q2 antenna limiters under ohmic and ICRH conditions. Simulations using 2D SolEdge3x profiles in COMSOL capture rectified sheath potentials exceeding 300 V, leading to strong upper-limiter localization. Both poloidal and toroidal asymmetries are observed and attributed to RF sheath effects, with modeled erosion patterns deviating from experiment—highlighting sensitivity to sheath geometry and plasma resolution. Erosion is driven primarily by high-charge-state oxygen ions (O6+–O8+), while D+ plays a negligible role. Assuming a plasma composition of 1% oxygen and 98% deuterium, STRIPE predicts a 30-fold increase in gross W erosion from ohmic to ICRH phases, consistent with a >25-fold rise in W-I (400.9 nm) brightness. Quantitative agreement is within 5% in the ohmic phase and 30% under ICRH, demonstrating predictive capability. Importantly, the study shows that the magnitude of ICRH-driven W erosion depends strongly on the concentration of light impurities (O, B, N, C), which drive sputtering through high charge states. Cleaner plasma conditions with reduced impurity content are therefore expected to substantially mitigate antenna W sources in WEST and other toroidal fusion devices. These findings establish STRIPE as a predictive framework for RF-induced plasma–material interactions and support its application to reactor-scale antenna design.

Kumar, Atul [ORNL] (ORCID:0000000277475210)↗
DOE OSTI2026

ICRF near-field effects sensitivity to magnetic tilt-angle

This paper complements the study reported in G. Urbanczyk et al 2025 Nucl. Fusion 65 046018 by investigating how near-field effects from Ion Cyclotron Range of Frequency (ICRF) antennas depend on the magnetic geometry, particularly focusing on the sensitivity of rectified sheath potentials and associated impurity production to variations in magnetic field tilt-angle. Simulations were conducted using Petra-M, employing a flat model of the ASDEX Upgrade (AUG) three-strap antenna, and COMSOL, utilizing a curved model of the WEST antenna. Results demonstrate indications of sensitivity of the rectified sheath potentials and impurity sputtering to the alignment of Faraday screen bars with the magnetic field lines, emphasizing the necessity for careful consideration of geometric alignment in antenna design for fusion devices. This trend is consistent with experimental data measured with various diagnostics.

Urbanczyk, Guillaume [Universite de Lorraine, Nanc↗
DOE OSTI2025

Runaway electron-induced plasma facing component damagein tokamaks

This Roadmap article addresses the critical and multifaceted challenge of plasma facing component (PFC) damage caused by runaway electrons (REs) in tokamaks, a phenomenon that poses a significant threat to the viability and longevity of future fusion reactors such as ITER and DEMO. The dramatically increased RE production expected in future high-current tokamaks makes it very difficult to avoid or mitigate REs in such devices when a plasma discharge terminates abnormally. Preventing damage from the intense localised heat loads they can cause requires a holistic approach that considers plasma, REs and PFC damage. Despite decades of progress in understanding the physics of REs and the thermomechanical response of PFCs separately, their complex interplay remains poorly understood. This document aims to initiate a coordinated, interdisciplinary approach to bridge this gap by reviewing experimental evidence, advancing diagnostic capabilities, and improving modelling tools across different scales, dimensionalities, and fidelities. Key topics include RE beam formation and transport, damage mechanisms in both brittle and metallic PFCs, and observed effects in major facilities such as JET, DIII-D, WEST and EAST. The Roadmap emphasises the urgency of predictive, high-fidelity modelling validated against well-diagnosed controlled experiments, particularly in the light of recent changes in ITER’s wall material strategy and the growing importance of private sector fusion initiatives. Each section of the Roadmap article is written to provide a concise overview of one area of this multidisciplinary subject, with an assessment of the status, a look at current and future challenges, and a brief summary. The ultimate goal of this initiative is to guide future mitigation strategies and design resilient components that can withstand the intense localised loads imposed by REs, thus ensuring the safe and sustainable operation of the next generation of fusion power plants.

Ratynskaia, Svetlana [KTH Royal Inst. of Technolog↗
DOE OSTI2025

Integrated modeling of RF-induced tungsten erosion at ICRH antenna structures in the WEST tokamak *

This paper introduces STRIPE (Simulated Transport of RF Impurity Production and Emission), an advanced modeling framework developed to analyze material erosion and the global transport of eroded impurities originating from radio-frequency (RF) antenna structures in magnetic confinement fusion devices. STRIPE integrates multiple physics modules: SolEdge3x for scrape-off-layer plasma profiles, COMSOL for 3D RF rectified sheath potentials, RustBCA for erosion yields and surface interactions, and global impurity transport for 3D ion energy-angle distributions and impurity transport. The framework is applied to an ion cyclotron RF-heated L-mode discharge (#57877) in the WEST tokamak, where it predicts a thirty-fold increase in gross tungsten erosion at antenna limiters during the transition from ohmic to ICRH operation. Additionally, under ICRH conditions, a tenfold enhancement in erosion is observed when comparing RF sheath effects to purely thermal sheath conditions. High-charge-state oxygen ions ($\mathrm{O}$ 6+ and above) are identified as the dominant contributors to tungsten sputtering. To validate the model, a synthetic diagnostic tool based on inverse photon efficiency (S/XB coefficients) from the ColRadPy collisional-radiative model enables direct comparison with spectroscopic measurements. Model predictions using a plasma composition of 1% oxygen and 99% deuterium show good agreement with observed W − I (400.9 nm) emission for discharge #57877, supporting the accuracy of the STRIPE framework. This study focuses specifically on gross erosion calculations to demonstrate STRIPE’s capabilities. Future extensions of this work will incorporate net erosion, re-deposition, self-sputtering effects, and whole-device modeling of sputtered tungsten impurity transport. STRIPE is also being applied to other RF-heated linear and toroidal devices, offering valuable insights for antenna design, impurity control, and performance optimization in next-generation fusion reactors.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2026

Measurement of the near-threshold 𝐽/𝜓 photoproduction cross section with the CLAS12 experiment

We present measurements of the total and differential cross sections for near-threshold 𝐽/𝜓 photoproduction obtained with the CLAS12 detector at the Thomas Jefferson National Accelerator Facility. The results are based on data collected during the fall 2018 and spring 2019 running periods, using electron beams with energies of 10.6 and 10.2 GeV, respectively, scattered off a liquid-hydrogen target. Near-threshold 𝐽/𝜓 photoproduction offers a unique sensitivity to the strong interaction in the nonperturbative regime of quantum chromodynamics (QCD). The energy dependence of the cross section constrains the underlying 𝐽/𝜓 production mechanisms, including multigluon exchange and potential baryonic excitations. Additionally, the 𝑡 dependence of the differential cross section can be related to the transverse spatial distribution of gluons in the proton, providing critical input for theoretical descriptions of the gluonic structure of the proton. An interpretation of the results in terms of the gluon content of the proton is presented, providing new experimental constraints on QCD-inspired models of the proton structure and the role of gluonic degrees of freedom in hadronic mass generation.

form factors↗
DOE OSTI2025

Inclusive electron scattering in the resonance region off a hydrogen target with CLAS12

Inclusive electron scattering cross sections off a hydrogen target at a beam energy of 10.6 GeV have been measured with data collected from the CLAS12 spectrometer at Jefferson Laboratory. These first absolute cross sections from CLAS12 cover a wide kinematic area in invariant mass 𝑊 of the final state hadrons from the pion threshold up to 2.5 GeV for each bin in virtual photon four-momentum transfer squared 𝑄 2 from 2.55 to 10.4GeV 2 owing to the large scattering angle acceptance of the CLAS12 detector. Comparison of the cross sections with the resonant contributions computed from the CLAS results on the nucleon resonance electroexcitation amplitudes has demonstrated a promising opportunity to extend the information on their 𝑄 2 evolution up to 10 GeV 2 . Together these results from CLAS and CLAS12 offer good prospects for probing the nucleon parton distributions at large fractional parton momenta 𝑥 for 𝑊<2.5 GeV, while covering the range of distances where the transition from the strongly coupled to the perturbative regimes is expected.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
DOE OSTI2026

Lagrange-Remap strategy for multi-material fluid-solid simulations using compressive limiters

In the present work, the Lagrange-Remap strategy proposed in [1] is extended to multi-material fluid-solid simulations. Both hypo-elastic and hyper-elastic material models are considered to describe the mechanical behavior of the solids. In practice, the deviatoric stress tensor (for hypo-elastic materials) and the left Cauchy-Green tensor (for isotropic hyper-elastic materials) are remapped, while the use of compressive limiters effectively reduces numerical diffusion during the remapping step. The simplicity of this diffuse interface approach is emphasized in the context of multi-material fluid-solid simulations. A series of Lagrange-Remap test cases, involving both solids and fluids, are conducted and compared with reference Lagrangian simulations, demonstrating the robustness and accuracy of the overall numerical strategy.

Compressive limiters↗
DOE OSTI2025

3D mesh regularization within an ALE code using a weighted line sweeping method

The Lagrangian formalism is widely used to simulate hydrodynamic responses in complex engineering applications, particularly those involving strong shock waves. However, as the mesh moves with the fluid, it can become highly distorted, requiring a regularization step. This involves constructing a new grid and remapping conservative quantities onto it to restore mesh quality. This work introduces a regularization method for block-structured meshes within a 3D ALE (Arbitrary Lagrangian-Eulerian) code. The proposed approach prevents mesh tangling while preserving the anisotropic features of the initial Lagrangian mesh. This regularization technique incorporates aspect ratio-based weights to control mesh smoothing. Unlike uniform rezoning techniques, this weighted approach maintains proximity to the Lagrangian mesh while improving mesh quality. Here, the method effectively handles concave geometries by mitigating the grid attraction phenomenon, which typically leads to mesh concentration along concave edges. Numerical experiments demonstrate its efficiency in regularizing severely deformed meshes, and its integration within the ALE framework is validated on challenging hydrodynamic test cases, including the triple point problem.

42 ENGINEERING↗
DOE OSTI2025

XPS post-mortem analysis of plasma-facing units extracted from WEST after the C3 (2018) and C4 (2019) campaigns

Four monoblocks coming from one ITER-like plasma-facing unit from the Q3B sector of the lower divertor, named as monoblock (MB)3, MB9, MB20, and MB30, were exposed to the deuterium and helium plasma mixture during the C3 (2018) and C4 (2019) campaigns of the Tungsten Environment in Steady-state Tokamak (WEST), followed by a detailed ex-situ X-ray photoelectron spectroscopy investigation. The surface and in-depth chemistry of the tungsten monoblocks indicated the formation of a re-deposited mixture in the deposition-dominated area of the divertor, thicker than 218 and 172 nm for MB3 and MB9, respectively. The redeposition layer was dominated by a mixture of boron carbides accompanied by tungsten carbides in MB3, while in MB9, the redeposition layer was dominated by tungsten borides. The remaining two monoblocks, MB20 and MB30, were collected from the erosion region and showed similar chemical behavior with a blended mixture of oxidized and metallic tungsten followed by boron carbides within a 50 nm depth range. Boron fixation in the layers is an expected consequence of the boronizations used during the operation, but the chemical status of redeposited elements was characterized for the first time in this work.

Marin, Alexandru [Pennsylvania State University]↗
DOE OSTI2025

Gapped commensurate antiferromagnetic response in a strongly underdoped model cuprate superconductor

It is a distinct possibility that spin fluctuations are the pairing interactions in numerous unconventional superconductors. In the high-transition-temperature (high-T c ) cuprates, superconductivity emerges upon doping antiferromagnetic Mott insulators, and spin fluctuations might furthermore drive unusual pseudogap phenomena. Here we use magnetic neutron scattering to study the highly underdoped cuprate HgBa 2 CuO 4+δ (hole concentration p ≈ 0.064). In contrast to prior results for other underdoped cuprates, we find no evidence of incommensurate magnetic order associated with spin-density-wave or stripe correlations. Instead, the antiferromagnetic response in both the superconducting and pseudogap states is gapped below Δ AF ≈ 6 meV, commensurate over a wide energy range, and disperses above about 55 meV. Given the pristine nature of HgBa 2 CuO 4+δ , which exhibits high structural symmetry and minimal point disorder effects, this behavior likely signifies the unmasked response of the underlying CuO 2 planes near the Mott-insulating state. These results serve as a benchmark for a refined theoretical understanding of the cuprates.

Materials science↗
DOE OSTI2026

The 0E2 benchmarks for PWR UO 2 decay heat: an analysis from the NEA WPNCS

This paper presents the work performed in the subgroup 16 of the Working Party for Nuclear Criticality Safety (WPNCS) of the OECD Nuclear Energy Agency. The main goal was to define two decay heat benchmarks for Spent Nuclear Fuel (one pincell and one assembly), perform calculations and compare and analyze the results in light of existing calorimetric measurements. The selected case is the PWR UO2 assembly 0E2, irradiated at the Ringhals-3 reactor and measured at the Clab facility in Sweden. In total, 21 institutes worldwide participated to the exercise, leading to 55 calculated results (named C). It was found that the measured decay heat values (E) can be satisfactorily reproduced with two-dimensional assembly calculations, leading to an average C/E value of 0.99, with an uncertainty (or one standard deviation) of ±0.01.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2025

Kelvin–Helmholtz instability under stabilizing parallel magnetic field in nonhomogeneous compressible MHD flows

We study the Kelvin–Helmholtz instability (KHI) for the general case of a compressible, nonhomogeneous, magnetized plasma flow. The study is limited to a vortex sheet interface with an imposed parallel magnetic field. We introduce a new formalism based on a convective Mach number M c , a convective Alfvénic Mach number M Ac , and a total convective Mach number that combines the two. We derive an analytic expression of the KHI growth rate for a homogeneous flow (i.e., zero Atwood number, A=0) that converges toward both the expression for unmagnetized compressible flow and Chandrasekhar's expression for magnetized incompressible flow. Otherwise, the dispersion relation is solved numerically and allows deriving general stability diagrams of magnetized KHI for the triplet (A, M c , β −plasma) parameters. We show these parameters uniquely define all configurations for a parallel magnetic field. We also construct diagrams with respect to the convective Alfvénic Mach number, the β − plasma parameter, or the magnetic field showing which magnetic field strength is required for stabilizing a given shear flow. The theoretical growth rates are compared with 18 simulations made with the GAMERA code, currently used for 3D magnetospheric simulations. Finally, we apply our results to the analysis of a past KHI experiment performed at the OMEGA laser facility, showing linear theory succeeds to provide accurate estimates of the growth rate at early times. We further discuss how our results can inform future experiments in the high-Mach magnetized regime at the National Ignition Facility. Possible limitations of the study due to resistive, mixing, or turbulence effects are discussed.

compressible flows↗
DOE OSTI2025

Calibration and characterization of the line-VISAR diagnostic at the HED-HIBEF instrument at the European XFEL

In dynamic-compression experiments, the line-imaging Velocity Interferometer System for Any Reflector (VISAR) is a well-established diagnostic used to probe the velocity history, including wave profiles derived from dynamically compressed interfaces and wavefronts, depending on material optical properties. Knowledge of the velocity history allows for the determination of the pressure achieved during compression. Such a VISAR analysis is often based on Fourier transform techniques and assumes that the recorded interferograms are free from image distortions. In this paper, we describe the VISAR diagnostic installed at the HED-HIBEF instrument located at the European XFEL along with its calibration and characterization. It comprises a two-color (532, 1064 nm), three-arm (with three velocity sensitivities) line imaging system. We provide a procedure to correct VISAR images for geometric distortions and evaluate the performance of the system using Fourier analysis. We finally discuss the spatial and temporal calibrations of the diagnostic. As an example, we compare the pressure extracted from the VISAR analysis of shock-compressed polyimide and silicon.

47 OTHER INSTRUMENTATION↗