Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “C++ analysis”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

ECAR-7517 Rev 1 MARVEL I&C Failure Modes and Effects Analysis

The purpose of this document is to perform a single-failure analysis through the use of a Failure Modes and Effects Analysis (FMEA) for the Safety Related components of the MARVEL Instrumentation and Control (I&C) System. The intent is that this document will meet the requirements for a single-failure analysis described in IEEE-379, “IEEE Standard for Application of the Single-Failure Criterion to Nuclear Power Generating Station Safety Systems”, to verify that this design does indeed meet the single failure criterion. Principles of IEEE-352, “IEEE Guide for General Principles of Reliability Analysis of Nuclear Power Generating Station Safety Systems” are followed to ensure the analysis is consistent with industry standards.

21 - SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLAN↗
NASA NTRS1986

Accurate determination of the fine-structure intervals in the 3P ground states of C-13 and C-12 by far-infrared laser magnetic resonance

Accurate values are presented for the fine-structure intervals in the 3P ground state of neutral atomic C-12 and C-13 as obtained from laser magnetic resonance spectroscopy. The rigorous analysis of C-13 hyperfine structure, the measurement of resonant fields for C-12 transitions at several additional far-infrared laser frequencies, and the increased precision of the C-12 measurements, permit significant improvement in the evaluation of these energies relative to earlier work. These results will expedite the direct and precise measurement of these transitions in interstellar sources and should assist in the determination of the interstellar C-12/C-13 abundance ratio.

Cooksy, A. L.↗
NASA NTRS1973

A determination of the earth tidal amplitude and phase from the orbital perturbations of the Beacon Explorer C spacecraft

An analysis of the orbital inclination of the Beacon Explorer C spacecraft over a period of nearly five months in 1970 revealed a very clear and distinctive perturbation caused by the earth and ocean tides. The perturbation has a full amplitude of about 1.8 seconds of arc and a period of about 85 days. This amplitude is approximately 15% smaller than would be expected from the solid-earth tide alone and is shifted slightly in phase. The perturbation can be represented almost exactly by a Love number of k sub 2 = 0.245 with a phase lag of 3.2 degrees. The data used were laser range measurements obtained by a NASA Goddard Space Flight Center tracking system in Greenbelt, Maryland.

Smith, D. E.↗
DOE OSTI2020

In Vivo Thermodynamic Analysis of Glycolysis in Clostridium thermocellum and Thermoanaerobacterium saccharolyticum Using 13 C and 2 H Tracers

Clostridium thermocellum and Thermoanaerobacterium saccharolyticum are thermophilic anaerobic bacteria with complementary metabolic capabilities that utilize distinct glycolytic pathways for the conversion of cellulosic sugars to biofuels. We integrated quantitative metabolomics with 2 H and 13 C metabolic flux analysis to investigate the in vivo reversibility and thermodynamics of the central metabolic networks of these two microbes. We found that the glycolytic pathway in C. thermocellum operates remarkably close to thermodynamic equilibrium, with an overall drop in Gibbs free energy 5-fold lower than that of T. saccharolyticum or anaerobically grown Escherichia coli . The limited thermodynamic driving force of glycolysis in C. thermocellum could be attributed in large part to the small free energy of the phosphofructokinase reaction producing fructose bisphosphate. The ethanol fermentation pathway was also substantially more reversible in C. thermocellummthan in T. saccharolyticum. These observations help explain the comparatively low ethanol titers of C. thermocellum and suggest engineering interventions that can be used to increase its ethanol productivity and glycolytic rate. In addition to thermodynamic analysis, we used our isotope tracer data to reconstruct the T. saccharolyticum central metabolic network, revealing exclusive use of the Embden-Meyerhof-Parnas (EMP) pathway for glycolysis, a bifurcated tricarboxylic acid (TCA) cycle, and a sedoheptulose bisphosphate bypass active within the pentose phosphate pathway. Thermodynamics constitutes a key determinant of flux and enzyme efficiency in metabolic networks. Here, we provide new insights into the divergent thermodynamics of the glycolytic pathways of C. thermocellum and T. saccharolyticum, two industrially relevant thermophilic bacteria whose metabolism still is not well understood. We report that while the glycolytic pathway in T. saccharolyticum is as thermodynamically favorable as that found in model organisms, such as E. coli or Saccharomyces cerevisiae , the glycolytic pathway of C. thermocellum operates near equilibrium. The use of a near-equilibrium glycolytic pathway, with potentially increased ATP yield, by this cellulolytic microbe may represent an evolutionary adaptation to growth on cellulose, but it has the drawback of being highly susceptible to product feedback inhibition. The results of this study will facilitate future engineering of high-performance strains capable of transforming cellulosic biomass to biofuels at high yields and titers.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2024

Systematic engineering for production of anti-aging sunscreen compound in Pseudomonas putida

Sunscreen has been used for thousands of years to protect skin from ultraviolet radiation. However, the use of modern commercial sunscreen containing oxybenzone, ZnO, and TiO 2 has raised concerns due to their negative effects on human health and the environment. In this study, we aim to establish an efficient microbial platform for production of shinorine, a UV light absorbing compound with anti-aging properties. First, we methodically selected an appropriate host for shinorine production by analyzing central carbon flux distribution data from prior studies alongside predictions from genome-scale metabolic models (GEMs). We enhanced shinorine productivity through CRISPRi-mediated downregulation and utilized shotgun proteomics to pinpoint potential competing pathways. Simultaneously, we improved the shinorine biosynthetic pathway by refining its design, optimizing promoter usage, and altering the strength of ribosome binding sites. Finally, we conducted amino acid feeding experiments under various conditions to identify the key limiting factors in shinorine production. The study combines meta-analysis of 13 C-metabolic flux analysis, GEMs, synthetic biology, CRISPRi-mediated gene downregulation, and omics analysis to improve shinorine production, demonstrating the potential of Pseudomonas putida KT2440 as platform for shinorine production.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2021

Effect of heat treatments on superconducting properties and connectivity in K-doped BaFe2As2

Abstract Fe-based superconductors and in particular K-doped BaFe 2 As 2 (K-Ba122) are materials of interest for possible future high-field applications. However the critical current density ( J c ) in polycrystalline Ba122 is still quite low and connectivity issues are suspected to be responsible. In this work we investigated the properties of high-purity, carefully processed, K-Ba122 samples synthesized with two separate heat treatments at various temperatures between 600 and 825 °C. We performed specific heat characterization and T c -distribution analysis up to 16 T and we compared them with magnetic T c and J c characterizations, and transmission-electron-microscopy (TEM) microstructures. We found no direct correlation between the magnetic T c and J c , whereas the specific heat T c -distributions did provide valuable insights. In fact the best J c -performing sample, heat treated first at 750 °C and then at 600 °C, has the peak of the T c -distributions at the highest temperatures and the least field sensitivity, thus maximizing H c2 . We also observed that the magnetic T c onset was always significantly lower than the specific heat T c : although we partially ascribe the lower magnetization T c to the small grain size (< λ , the penetration depth) of the K-Ba122 phase, this behaviour also implies the presence of some grain-boundary barriers to current flow. Comparing the T c -distribution with J c , our systematic synthesis study reveals that increasing the first heat treatment above 750 °C or the second one above 600 °C significantly compromises the connectivity and suppresses the vortex pinning properties. We conclude that high-purity precursors and clean processing are not yet enough to overcome all J c limitations. However, our study suggests that a higher temperature T c -distribution, a larger H c2 and a better connectivity could be achieved by lowering the second heat treatment temperature below 600 °C thus enhancing, as a consequence, J c .

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2025

Quantitative decoding of coupled carbon and energy metabolism in Pseudomonas putida for lignin carbon utilization

Soil Pseudomonas species, which thrive on lignin derivatives, are widely explored for biotechnology applications in lignin valorization. However, how the native metabolism coordinates phenolic carbon processing with required cofactor generation remains poorly understood. Here, we achieve quantitative understanding of this metabolic balance through a detailed multi-omics investigation of Pseudomonas putida KT2440 grown on four common phenolic acid substrates: ferulate, p-coumarate, vanillate, and 4-hydroxybenzoate. Relative to succinate, proteomics reveals > 140-fold increase in transport and catabolic proteins for aromatics, but metabolomics identifies bottlenecks in initial catabolism to maintain favorable cellular energy charge, which is compromised in mutants with resolved bottlenecks. Up to 30-fold increase in pyruvate carboxylase and glyoxylate shunt proteins implies a metabolic remodeling confirmed by kinetic 13 C-metabolomics. Quantitative analysis by 13 C-fluxomics demonstrates coupling of this remodeling with cofactor production. Specifically, anaplerotic carbon recycling through pyruvate carboxylase promotes tricarboxylic acid cycle fluxes to generate 50-60% NADPH yield and 60-80% NADH yield, resulting in up to 6-fold greater ATP surplus than with succinate metabolism; the glyoxylate shunt sustains cataplerotic flux through malic enzyme for the remaining NADPH yield. This quantitative blueprint affords cofactor imbalance predictions in proposed engineering of key metabolic nodes in lignin valorization pathways.

09 BIOMASS FUELS↗
NASA NTRS1984

Thermogravimetric analysis of silicon carbide-silicon nitride fibers at ambient to 1000 C in air

Thermogravimetric analysis of silicon carbide-silicon nitride fibers was carried out at ambient to 1000 C in air. The weight loss over this temperature range was negligible. In addition, the oxidative stability at high temperature for a short period of time was determined. Fibers heated at 1000 C in air for fifteen minutes showed negligible weight loss (i.e., less than 1 percent).

Daniels, J. G.↗
NASA NTRS2023

STXM-C-XANES, IR Microspectroscopy, and Raman Microspectroscopy Analysis of Organic Matter in the Chwichiya 002 C3.00-Ungrouped Chondrite

Chwichiya 002 is a C3.00-ungrouped carbonaceous chondrite discovered in Western Sahara in 2018. The presence of hydrated phases in Chwichiya 002 was not confirmed by XRD analysis, and only a faint water and Si-O band attributed to phyllosilicate were observed by infrared transmission spectroscopy, indicating a very low degree of aqueous alteration (Meteoritical Bulletin, 2020). The structural order of polycyclic aromatic hydrocarbons evaluated by Raman spectroscopy indicates that the effect of thermal metamorphism is less severe than in the Semarkona meteorite, an LL3.00 ordinary chondrite (Meteoritical Bulletin, 2020). Chiwichiya 002 is a very primitive carbonaceous chondrite and an important information source for the early stage of the evolution of organic matter in the solar system. In this study, we investigated the molecular structure and distribution of organic matter in Chiwichiya 002 by Carbon X-ray Absorption Near Edge Structure (C-XANES) analysis using a Scanning Transmission X-ray Microscope (STXM). The STXM-C-XANES analysis has a spatial resolution of 20~100 nm and can observe the spatial distribution of organic materials in microstructures. In addition, to investigate the degree of thermal metamorphism of the organic matter, micro-IR, and micro-Raman spectroscopic analyses were performed. In addition, the Murchison CM2 chondrite was also analyzed for comparison. To evaluate contamination during analytical procedures, antigorite, which was heated in air at 500°C for 5 hours to eliminate organic matter was also analyzed in the same manner. The samples were milled into 100 nm-thick, thin sections using a Focused Ion Beam (FIB), and C-XANES spectra were obtained using the STXM at the High Energy Accelerator Research Organization, Photon Factory (PF), BL-19B. The obtained C-XANES spectra were smoothed and then fitted with Gaussian functions using the method of Le Guillou et al. (2018). The C-XANES showed that the ratio of oxygenated functional group (ketone, phenolic) carbons in Chwichiya 002 was lower than in Murchison, whereas the ratio of aliphatic carbons was almost the same. This may reflect the low degree of aqueous alteration of Chwichiya 002. In addition, contamination peaks were detected at 287.3-287.7 eV and 288.3-288.7 eV in the C-XANES spectra of some of the antigorite samples. The source of these peaks is under investigation. Raman spectroscopic analysis showed that the intensity ratio of the D band to the G band of Chwichiya 002 was slightly higher than that of Murchison. IR absorption spectra showed aromatic absorption at 1630 cm -1 , but there was little absorption due to aliphatic C-H around 2900 cm -1 . These results suggest that the organic matter in Chwichiya 002 may be more heated than in Murchison.

Chwichiya 002↗
NASA NTRS1972

Analysis of requirements for GEOS-C laser cube-corner reflector panels

A mathematical analysis of the tradeoffs and requirements was performed to develop an improved array design which will give stronger returns at lower elevation angles and reduce pulse spread in the return. It was determined that a zenith angle of 75deg can be obtained with an array with an area of 0.28 sq m, if the array is shaped on the surface of a 45 deg cone whose axis is coincident to the satellite axis. The total weight of the truncated pyramid array with 270 cube corners is calculated to be not more than 50% greater than the GEOS 2 array, while the efficiency is increased 275%.

Minott, P. O.↗
NASA NTRS2001

Selection of the Ground Segment for the Next Generation Space Telescope (NGST) Flight Demonstrator (Nexus)

Nexus was a technology demonstrator project that was designed to bridge from the Hubble Space Telescope (HST) to its successor, the Next Generation Space Telescope (NGST). This paper focuses on the process used in designing the ground segment for Nexus and the lessons learned in its development. Ground station cost drivers were: (1) Contact time, (2) Cost of transporting data between the ground stations and control center, and (3) Cost savings via ground automation. We found that reducing the communication requirement in just the first 100 days could have reduced the total ground station cost by 40%. Contact time cost dwarfed the cost trade between automation development and off-shift operations personnel. Real-time Telemetry and Control (T&C) system analysis was divided into: (1) Potential reuse of the Nexus real-time (T&C) system for NGST, (2) Feasibility of using a 'Finite State-Based Modeling' product, and (3) Selecting a Commercial Off the Shelf (COTS) versus Government Off The Shelf (GOTS) products. We found that each of the products evaluated in detail (ASIST, EPOCH 2000, and ITOS) could adequately support basic mission requirements. Lessons learned were: (1) Include operations at the beginning of the mission, and (2) Develop an operations concept as soon as possible.

Gal-Edd, Jonathan↗
NASA NTRSDate not supplied

Analysis of "Stone" Samples from C-Type Asteroid Ryugu

As a part of activities of initial analysis, we analyzed eighteen Ryugu “stone” samples of 1 ~ 8mm in size: seven stones from the 1st touch down site and eleven from the 2nd touch down site. Ryugu stones were analyzed first using X-rays, UV, visible, near-infrared, mid-infrared, and muon probes for surface reflectance spectra, internal 3D structure and element distribution, crystal structures, and bulk composition of light elements such as C, N, and O. Measurements for magnetic, thermal, and physical properties using some stones were also performed. TOF-SIMS analysis of fluid inclusions as being continued. Small particles separated from some stones were analyzed by IR-CT. Based on 3D-CT images of individual stones, objects of interests were identified, separated by pFIB cutting, and exposed by polishing on the surface of epoxy disks. FE-EPMA/FE-SEM analysis was made on ~40 polished epoxy disks for chemical composition and textural observation. FIB sections and small (~15 μm in size) fragments were separated from polished surface and analyzed by TEM, STXM,XRF, and nano-CT.

T. Nakamura↗
DOE OSTI2026

An experimental and kinetic modeling study of the ignition of 2-methyl decane

Ignition delay times (IDTs) of 2-methyl decane (C 11 H 24 -2) are measured in a high-pressure shock tube and in a rapid compression machine at equivalence ratios in the range 0.5–2.0 at 90 % dilution, at temperatures in the range 600–1430 K and at pressures of 15 and 30 bar. To clarify the effect of the branched methyl group on fuel oxidation, IDTs of n-undecane (nC 11 H 24 ) are also measured at similar conditions to those measured for C 11 H 24 -2. A new chemical kinetic mechanism, using C3MechV4.0.1 as the core chemistry, is developed and validated against the new experimental data. The thermodynamic properties of the fuel (RH), alkyl (Ṙ), alkyl peroxy (RȮ 2 ), hydroperoxy-alkyl (Q̇OOH), and peroxy hydroperoxy alkyl (Ȯ 2 QOOH) radicals are updated in both the C 11 H 24 -2 and nC 11 H24 models using THERM25. A reaction path flux analysis for C 11 H 24 -2 at different temperatures was conducted. Compared to nC 11 H 24 , C 11 H 24 -2 shows slower reactivity. At low and intermediate temperatures, the chain propagation pathway Q̇OOH ↔ C 11 cyclic ether + ȮH is favored for C 11 H 24 -2, while the chain branching pathway Q̇OOH ↔ Ȯ 2 QOOH ↔ C 11 carbonyl hydroperoxide (KHP) + ȮH is suppressed, leading to lower reactivity compared to nC 11 H 24 . At high temperatures, the presence of the branched methyl group inhibits the direct decomposition of the fuel, resulting in reduced C 2 H 4 formation, which in turn suppresses the reactivity of the fuel.

2-methyl decane↗
NASA NTRS2010

279 - Xanes Studies on UV-Irradiated Interstellar Ice Analogs: A Comparison to STARDUST Samples

We present C-, N-, and O-XANES (X-ray Absorption Near-Edge Spectroscopy) results of organic residues produced in the laboratory from the UV irradiation of astrophysical ice analogs containing H20, CO, CH30H, NH31 in order to mimic processes that may occur in cold icy bodies of the outer Solar System, particularly in comets, Such analyses showed that laboratory-formed organic residues mainly consist of a solid phase and an oily phase. C-XANES analysis of the solid phase suggests a rich distribution of organic functionalities, among which carbonyl groups, C=C bonds, and alcohols are present. Results from N-XANES indicate the possible presence of amide, amine, and nitrile groups, The O-XANES spectra confirmed the a-bearing groups, These results are compared with the XANES spectra obtained from STARDUST cometary samples,

Milam, Stefanie N.↗
NASA NTRS1986

Radionuclide measurements by accelerator mass spectrometry at Arizona

Over the past years, Tandem Accelerator Mass Spectrometry (TAMS) has become established as an important method for radionuclide analysis. In the Arizona system the accelerator is operated at a thermal voltage of 1.8MV for C-14 analysis, and 1.6 to 2MV for Be-10. Samples are inserted into a cesium sputter ion source in solid form. Negative ions sputtered from the target are accelerated to about 25kV, and the injection magnet selects ions of a particular mass. Ions of the 3+ charge state, having an energy of about 9MeV are selected by an electrostatic deflector, surviving ions pass through two magnets, where only ions of the desired mass-energy product are selected. The final detector is a combination ionization chamber to measure energy loss (and hence, Z), and a silicon surface-barrier detector which measures residual energy. After counting the trace iosotope for a fixed time, the injected ions are switched to the major isotope used for normalization. These ions are deflected into a Faraday cup after the first high-energy magnet. Repeated measurements of the isotope ratio of both sample and standards results in a measurement of the concentration of the radionuclide. Recent improvements in sample preparation for C-14 make preparation of high-beam current graphite targets directly from CO2 feasible. Except for some measurements of standards and backgrounds for Be-10 measurements to date have been on C-14. Although most results have been in archaeology and quaternary geology, studies have been expanded to include cosmogenic C-14 in meteorites. The data obtained so far tend to confirm the antiquity of Antarctic meteorites from the Allan Hills site. Data on three samples of Yamato meteorites gave terrestrial ages of between about 3 and 22 thousand years.

Jull, A. J. T.↗
NASA NTRSDate not supplied

FRET Tutorial

In this tutorial, we present the FRET tool for writing, understanding, formalizing and analyzing requirements. In practice, requirements are typically written in natural language, which is ambiguous and consequently not amenable to formal analysis. Since formal, mathematical notations are unintuitive, requirements in FRET are entered in a restricted, natural language, called FRETish with precise unambiguous meaning. This tutorial explains how requirements can be captured in FRETish and subsequently formalized in temporal logics and in the synchronous data flow language Lustre. We show, through multiple examples, how FRET assists users in understanding FRETish requirements and clarifying subtle semantic issues through English and diagrammatic explanations as well as interactive simulation. FInally, this tutorial describes how FRET can be used to perform realizability checking for identifying conflicting requirements and the connection of FRET with (1) the CoCoSim automated analysis tool for the verification of Simulink and Stateflow models, and (2) the Copilot runtime monitoring tool for the analysis of C programs.

FRET↗
DOE OSTI2022

Renewable low viscosity polyester-polyols for biodegradable thermoplastic polyurethanes

In the transition to renewably sourced, biodegradable polymers, the preparation of low viscosity polyester-polyols has posed a challenge for renewable polyurethane (PU) development. Low viscosity polyols not only reduce the requirement for high process temperatures but also decrease manufacturing time. In our efforts to incorporate increasing ratios of bio-based monomers into renewable PUs, we mixed diacids such as even carbon sebacic acid and odd carbon azelaic acid along with a renewable diol. This provided library of 2000 g/mol molecular weight polyester-polyols, and structures were established by 1 H and 13 C NMR analysis. The prepared polyester-polyols offered lower viscosity and enable lower fabrication temperatures to make TPUs, and their structure and material metrics were evaluated. The formation of TPUs is ascertained from FTIR and NMR analysis. The final TPUs displayed good physical and mechanical properties. Further, these TPUs exhibited T g in the range of -56.5 to -39.7°C, corresponding to TPU soft block structure, and T m between 98.3 and 105.1°C originating from the hard segment. Prepared TPUs exhibit excellent biodegradation under compost environmental conditions. These TPUs showed up to 57% decrease in molecular weight by GPC analysis after 9 weeks of biodegradation, and respirometer analysis displayed up to 97% biodegradation over 120 days.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
NASA NTRS1976

New aromatic silicon-containing polyamides

The experiments described were aimed at studying systematically the effect of silyl linkages on the thermogravimetric and thermomechanical properties of aromatic polyamides. Specifically, 18 aromatic silicon-containing polyamides were synthesized via interfacial polymerization of six silicon-containing diacid chlorides with 3,3-prime-diaminodiphenylmethane, 3,3-prime-diaminobenzophenone, and 1-(3-prime-aminobenzyl)-4-(3-double prime-aminobenzoyl)benzene. All polyamides were soluble in m-cresol and N,N-dimethylacetamide, and had glass transition temperatures between 178 and 254 C. Thermogravimetric analysis conducted in static air on film specimens showed 5 and 10 percent weight losses between 331 and 400 C and 354 and 440 C, respectively. The potential gain in processability engendered by incorporation of silane substituents was offset in most cases by substantial losses in thermo-oxidative stability.

Pratt, J. R.↗