Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Boundary identification”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8
All sourcesNASA NTRSDOE OSTI
NASA NTRS2022

Identification of Best Practices for Predicting Inlet Performance Using FUN3D Part 2: Installed Inlets.

A series of studies were performed to assess the impacts of boundary condition type and placement, grid refinement, and modeling parameters such as turbulence model and flux limiter on the predicted inlet performance for installed inlet configurations using the FUN3D flow solver. Two configurations were considered for the study; a wall-mounted Boundary Layer Ingestion (BLI) inlet and the C607 propulsion model tested in the 8x6 Supersonic Wind Tunnel at the NASA Glenn Research Center. The results of the studies were to be used to recommend best practices, as well as to assess the accuracy of FUN3D for inlet predictions. The results of BLI inlet stud-ies showed a minimal impact of grid refinement on the predicted inlet performance for a constant mass flow rate through the inlet. For the C607 propulsion model, the results showed that while the FUN3D predictions at the Aerodynamic Inter-face Plane (AIP) qualitatively agree with the experimental data, FUN3D showed a tendency to overpredict the circumferential distortion metric (IDCmax) and un-derpredict both the radial distortion metric (IDRmax) and the pressure recovery at the AIP (PRAIP ), with the differences between FUN3D and the experimental data increasing with increasing grid refinement and Mach number. Additionally, the outflow boundary location studies performed for both geometries showed that the solution at the AIP was not significantly impacted by the outflow boundary location as long as it was not placed at the location of the AIP. The modeling parameter studies did not indicate a path forward for improved predictions for either inlet con-figuration. Finally, comparisons between the mass flow plug and outflow geometry versions of the C607 propulsion model illustrated favorable agreement, which indi-cates that the differences observed are not caused by the outflow boundary model for this problem. This problem poses significant challenges to Reynolds-averaged Navier-Stokes (RANS) solvers due to the presence of shocks and flow separation in the inlet.

FUN3D↗
DOE OSTI2024

Aerosol Vertical Turbulent Mass Flux Retrievals Through Novel Remote Sensing Algorithm

Abstract Integrated measurements of aerosol, radiation, cloud, and turbulent transport in the planetary boundary layer (PBL) are essential for understanding and modeling climate and air quality. Here, we developed a new technique for the identification of convective turbulent regions and deriving the vertical distribution of aerosol turbulent mass fluxes within PBL. The algorithm uses retrievals from coherent Doppler lidars and a high spectral resolution lidar. The technique was applied to study particle mass fluxes over 2 months (November–December 2020) during the campaign conducted at the DOE Atmospheric Radiation Measurement Southern Great Plains (SGP) site in Lamont, Oklahoma. The algorithm developed here is capable of continuously deriving vertically resolved (curtains) aerosol mass fluxes. Our data analysis shows that at the site, the 30‐min averaged fluxes at 135 m above the surface were mainly positive (upward) at ∼1 μg m −2 s −1 , suggesting that the surface is the primary source of the particle mass supplied to the boundary layer at the SGP site. Analyses of the individual case studies have revealed that not all the derived fluxes can be linked to surface emissions. Both positive and negative values in a range of ±5 μg m −2 s −1 can be caused by convective thermals interacting between the residual layer and the mixed layer and by rotation of the horizontal wind with the height. Large erroneous negative fluxes can also be caused by drizzling/precipitating clouds. We anticipate that the application of the current technique will lead to a more realistic representation of aerosol mass budgets and bidirectional mixing rates.

54 ENVIRONMENTAL SCIENCES↗
NASA NTRS2002

Sliding-Mode Control Applied for Robust Control of a Highly Unstable Aircraft

An investigation into the application of an observer based sliding mode controller for robust control of a highly unstable aircraft and methods of compensating for actuator dynamics is performed. After a brief overview of some reconfigurable controllers, sliding mode control (SMC) is selected because of its invariance properties and lack of need for parameter identification. SMC is reviewed and issues with parasitic dynamics, which cause system instability, are addressed. Utilizing sliding manifold boundary layers, the nonlinear control is converted to a linear control and sliding manifold design is performed in the frequency domain. An additional feedback form of model reference hedging is employed which is similar to a prefilter and has large benefits to system performance. The effects of inclusion of actuator dynamics into the designed plant is heavily investigated. Multiple Simulink models of the full longitudinal dynamics and wing deflection modes of the forward swept aero elastic vehicle (FSAV) are constructed. Additionally a linear state space models to analyze effects from various system parameters. The FSAV has a pole at +7 rad/sec and is non-minimum phase. The use of 'model actuators' in the feedback path, and varying there design, is heavily investigated for the resulting effects on plant robustness and tolerance to actuator failure. The use of redundant actuators is also explored and improved robustness is shown. All models are simulated with severe failure and excellent tracking, and task dependent handling qualities, and low pilot induced oscillation tendency is shown.

Vetter, Travis Kenneth↗
NASA NTRS2003

Colossal Tooling Design: 3D Simulation for Ergonomic Analysis

The application of high-level 3D simulation software to the design phase of colossal mandrel tooling for composite aerospace fuel tanks was accomplished to discover and resolve safety and human engineering problems. The analyses were conducted to determine safety, ergonomic and human engineering aspects of the disassembly process of the fuel tank composite shell mandrel. Three-dimensional graphics high-level software, incorporating various ergonomic analysis algorithms, was utilized to determine if the process was within safety and health boundaries for the workers carrying out these tasks. In addition, the graphical software was extremely helpful in the identification of material handling equipment and devices for the mandrel tooling assembly/disassembly process.

Hunter, Steve L.↗
NASA NTRS1984

Spatial variation analyses of Thematic Mapper data for the identification of linear features in agricultural landscapes

A need exists for digitized information pertaining to linear features such as roads, streams, water bodies and agricultural field boundaries as component parts of a data base. For many areas where this data may not yet exist or is in need of updating, these features may be extracted from remotely sensed digital data. This paper examines two approaches for identifying linear features, one utilizing raw data and the other classified data. Each approach uses a series of data enhancement procedures including derivation of standard deviation values, principal component analysis and filtering procedures using a high-pass window matrix. Just as certain bands better classify different land covers, so too do these bands exhibit high spectral contrast by which boundaries between land covers can be delineated. A few applications for this kind of data are briefly discussed, including its potential in a Universal Soil Loss Equation Model.

Pelletier, R. E.↗
DOE OSTI2026

Energy-Optimal Vehicle Longitudinal Motion Control via Pontryagin’s Minimum Principle and Ultra-Local Model

Longitudinal vehicle motion control is essential for enhancing performance and optimizing a vehicle’s energy usage. However, it remains a challenging task due to the nonlinear and uncertain nature of vehicle dynamics, along with varying driving conditions. This paper presents a novel ultra-local optimal control approach based on Pontryagin’s Minimum Principle (PMP) that circumvents the need for detailed system identification by employing an ultra-local model. The control objective is to minimize the total energy consumption under boundary conditions while ensuring smooth traction force generation. The proposed approach is evaluated using a high-fidelity vehicle model in three representative scenarios: (i) nominal driving, (ii) a change in tire road friction coefficient (TRFC) from 0.5 to 0.65 and road slope from 0% to 5% during the maneuver, with target velocity unchanged, and (iii) a change in target velocity from 20 m/s to 0 m/s during the maneuver, while maintaining nominal TRFC and slope conditions. The simulation results demonstrate that the proposed method delivers robust performance, effectively balancing consumption and tracking accuracy in all tested scenarios.

Waleed khan, Muhammad [The University of Texas at ↗
NASA NTRS2005

The NASA Icing Remote Sensing System

NASA and the U.S. Army Cold Regions Research and Engineering Laboratory (CRREL) have an on-going activity to develop remote sensing technologies for the detection and measurement of icing conditions aloft. A multiple instrument approach is the current emphasis of this activity. Utilizing radar, radiometry, and lidar, a region of supercooled liquid is identified. If the liquid water content (LWC) is sufficiently high, then the region of supercooled liquid cloud is flagged as being an aviation hazard. The instruments utilized for the current effort are an X-band vertical staring radar, a radiometer that measures twelve frequencies between 22 and 59 GHz, and a lidar ceilometer. The radar data determine cloud boundaries, the radiometer determines the sub-freezing temperature heights and total liquid water content, and the ceilometer refines the lower cloud boundary. Data are post-processed with a LabVIEW program with a resultant supercooled LWC profile and aircraft hazard identification. Remotely sensed measurements gathered during the 2003-2004 Alliance Icing Research Study (AIRS II) were compared to aircraft in-situ measurements. Although the comparison data set is quite small, the cases examined indicate that the remote sensing technique appears to be an acceptable approach.

Reehorst, Andrew L.↗
NASA NTRS2005

NASA Icing Remote Sensing System Comparisons From AIRS II

NASA has an on-going activity to develop remote sensing technologies for the detection and measurement of icing conditions aloft. A multiple instrument approach is the current emphasis of this activity. Utilizing radar, radiometry, and lidar, a region of supercooled liquid is identified. If the liquid water content (LWC) is sufficiently high, then the region of supercooled liquid cloud is flagged as being an aviation hazard. The instruments utilized for the current effort are an X-band vertical staring radar, a radiometer that measures twelve frequencies between 22 and 59 GHz, and a lidar ceilometer. The radar data determine cloud boundaries, the radiometer determines the sub-freezing temperature heights and total liquid water content, and the ceilometer refines the lower cloud boundary. Data is post-processed with a LabVIEW program with a resultant supercooled LWC profile and aircraft hazard identification. Individual remotely sensed measurements gathered during the 2003-2004 Alliance Icing Research Study (AIRS II) were compared to aircraft in-situ measurements. Comparisons between the remote sensing system s fused icing product and in-situ measurements from the research aircraft are reviewed here. While there are areas where improvement can be made, the cases examined indicate that the fused sensor remote sensing technique appears to be a valid approach.

Reehorst, Andrew L.↗
DOE OSTI2022

Quasiparticle excitations in a one-dimensional interacting topological insulator: Application for dopant-based quantum simulation

Here, we study the effects of electron-electron interactions on the charge excitation spectrum of the spinful Su-Schrieffer-Heeger (SSH) model, a prototype of a one-dimensional bulk obstructed topological insulator. In view of recent progress in the fabrication of dopant-based quantum simulators we focus on experimentally detectable signatures of interacting topology in finite lattices. To this end we use Lanczos-based exact diagonalization to calculate the single-particle spectral function in real space which generalizes the local density of states to interacting systems. Its spatial and spectral resolution allows for the direct investigation and identification of edge states. By studying the noninteracting limit, we demonstrate that the topological in-gap states on the boundary are robust against both finite-size effects as well as random bond and onsite disorder which suggests the feasibility of simulating the SSH model in engineered dopant arrays in silicon. While edge excitations become zero-energy spinlike for any finite interaction strength, our analysis of the spectral function shows that the single-particle charge excitations are gapped out on the boundary. Despite the loss of topological protection, we find that these edge excitations are quasiparticlelike as long as they remain within the bulk gap. Above a critical interaction strength of U c ≈5t these quasiparticles on the boundary lose their coherence which is explained by the merging of edge and bulk states. This is in contrast to the many-body edge excitations which survive the limit of strong coupling, as established in the literature. Our findings show that for moderate repulsive interactions the nontrivial phase of the interacting SSH model can be detected through remnant signatures of topological single-particle states using single-particle local measurement techniques such as scanning tunneling spectroscopy.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
NASA NTRS1974

Recording and cataloging hazards information, revision A

A data collection process is described for the purpose of discerning causation factors of accidents, and the establishment of boundaries or controls aimed at mitigating and eliminating accidents. A procedure is proposed that suggests a discipline approach to hazard identification based on energy interrelationships together with an integrated control technique which takes the form of checklists.

Stein, R. J.↗
NASA NTRS2006

Acoustic Source Localization in Aircraft Interiors Using Microphone Array Technologies

Using three microphone array configurations at two aircraft body stations on a Boeing 777-300ER flight test, the acoustic radiation characteristics of the sidewall and outboard floor system are investigated by experimental measurement. Analysis of the experimental data is performed using sound intensity calculations for closely spaced microphones, PATCH Inverse Boundary Element Nearfield Acoustic Holography, and Spherical Nearfield Acoustic Holography. Each method is compared assessing strengths and weaknesses, evaluating source identification capability for both broadband and narrowband sources, evaluating sources during transient and steady-state conditions, and quantifying field reconstruction continuity using multiple array positions.

Sklanka, Bernard J.↗
NASA NTRS1987

Origin of northern lowland plains: Constraints from boundary morphology

The origin of the surface units of the northern lowland plains of Mars, about one third of the planet's surface, remains unclear after 20 years of analysis of spacecraft data. Hypotheses were put forward to explain the morphologies. The chief problem with constraining models of plains formation is that characterizing plains surface-forming processes is dependent upon the identification of distinctive landforms within the plains. The most commonly cited examples of distinctive morphologies found within the northern lowlands include: wrinkle ridges; small domes; giant polygons; and curvilinear ridges and ground undulations. To further constrain the processes involved, a careful analysis of boundary morphology is being conducted.

Parker, Timothy J.↗
NASA NTRS1975

Geologic and mineral and water resources investigations in western Colorado, using Skylab EREP data

The author has identified the following significant results. Skylab photographs are superior to ERTS images for photogeologic interpretation, primarily because of improved resolution. Lithologic contacts can be detected consistently better on Skylab S190A photos than on ERTS images. Color photos are best; red and green band photos are somewhat better than color-infrared photos; infrared band photos are worst. All major geologic structures can be recognized on Skylab imagery. Large folds, even those with very gentle flexures, can be mapped accurately and with confidence. Bedding attitudes of only a few degrees are recognized; vertical exaggeration factor is about 2.5X. Mineral deposits in central Colorado may be indicated on Skylab photos by lineaments and color anomalies, but positive identification of these features is not possible. S190A stereo color photography is adequate for defining drainage divides that in turn define the boundaries and distribution of ground water recharge and discharge areas within a basin.

Lee, K.↗
NASA NTRS1982

Time-marching transonic flutter solutions including angle-of-attack effects

Transonic aeroelastic solutions based upon the transonic small perturbation potential equation were studied. Time-marching transient solutions of plunging and pitching airfoils were analyzed using a complex exponential modal identification technique, and seven alternative integration techniques for the structural equations were evaluated. The HYTRAN2 code was used to determine transonic flutter boundaries versus Mach number and angle-of-attack for NACA 64A010 and MBB A-3 airfoils. In the code, a monotone differencing method, which eliminates leading edge expansion shocks, is used to solve the potential equation. When the effect of static pitching moment upon the angle-of-attack is included, the MBB A-3 airfoil can have multiple flutter speeds at a given Mach number.

Edwards, J. W.↗
NASA NTRS1982

Time-marching transonic flutter solutions including angle-of-attack effects

Transonic aeroelastic solutions based upon the transonic small perturbation potential equation are studied. Time-marching transient solutions of plunging and pitching airfoils are analyzed using a complex exponential modal identification technique, and seven alternative integration techniques for the structural equations are evaluated. The HYTRAN2 code is used to determine transonic flutter boundaries versus Mach number and angle-of-attack for NACA 64A010 and MBB A-3 airfoils. In that code, a monotone differencing method, which eliminates leading edge expansion shocks, is used to solve the potential equation. When the effect of static pitching moment upon the angle-of-attack is included, the MBB A-3 airfoil can have multiple flutter speeds at a given Mach number.

Edwards, J. W.↗
NASA NTRS1990

Regolith-structure modeling of lunar facilities

The mechanical properties of lunar regolith are significantly different from terrestrial soils; at low stress levels, the ultimate strength envelope is highly nonlinear, and the material is essentially dilatant. The effects of platen friction, membrane confinement, and material self weight in triaxial tests have been shown to be of great significance in low stress level tests. An inverse identification technique has been devised to account for these effects where the load-displacement response of the entire specimen, including the boundary conditions and the self-weight, was analyzed by nonlinear finite element techniques so as to obtain true material parameters.

Perkins, Steven W.↗
NASA NTRS1976

The magnetosphere of Venus - Evidence for a boundary layer and a magnetotail

Mariner 5 magnetic field data collected during its flyby of Venus are evaluated in the light of reexamination of Venera data and in the context of present knowledge on the interaction of the solar wind with the earth. Attention is focused on an analysis of 4 phenomenological regions: magnetosheath, boundary layer, tail, and upstream waves. Enough evidence is revealed for a boundary layer beginning in the dayside ionosphere. The study affirms the possibility that Venus has an intrinsic magnetotail; the key elements of this identification are the positions of the Mariner 5, Venera 4 and Venera 9 magnetopause crossings and the agreements of the polarity of the field during the Mariner 5 and Venera 9 wake traversals with the direction of the implied Venera 4 dipole moment.

Russell, C. T.↗