Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Automotive”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8

Unsteady velocity field measurements at the outlet of an automotive supercharger using particle image velocimetry (PIV)

Particle image velocimetry (PIV) was used to study air flow characteristics at the outlet of an automotive supercharger. Instantaneous velocity fields were analyzed to yield ensemble-averaged velocities and Reynolds stresses, and the ensemble-averages were used to determine maximum velocity and exit flow angle as a function of blade position for various speeds and pressure ratios. The results show that the flow exits the supercharger as a high-speed jet that not only varies in the parallel plane but also in the perpendicular plane, generating a complex three-dimensional flow. The flow varies in the magnitude and the angle at which it leaves the supercharger with the change in blade position and follows a periodic behavior. The maximum velocity at which the flow exits the supercharger also follows a periodic behavior with a variation of 25-30% observed for all the cases. In the parallel plane, the exit angles are periodic every 60 deg of blade rotation and vary by as much as 40 deg, whereas periodic behavior with every 120 deg of blade rotation and a variation of 60 deg is observed in the perpendicular plane. Variation in flow with blade position is also observed in the velocity and turbulence profiles, with periodic behavior with every 60 blade rotation. The velocity and velocity fluctuation profiles show that the unsteady nature of the flow is most significant close to the outlet, and these unsteady variations diminish 58 mm downstream of the outlet. An exit flow pattern of a figure 8 is generated as the flow leaves the blades with one complete blade rotation of 120 for all the cases, except 4000 rpm, pressure ratio 1.4, where the flow exits in a circular pattern. (author)

33 ADVANCED PROPULSION SYSTEMS↗

Automotive fuel cell stack and system efficiency and fuel consumption based on vehicle testing on a chassis dynamometer at minus 18 °C to positive 35 °C temperatures

In this work we present an in-depth laboratory technology assessment of a 2016 Toyota Mirai Fuel Cell (FC) vehicle based on chassis dynamometer testing. The 114.6 kW FC stack has a high dynamic response, which makes this powertrain a FC-dominant hybrid electric vehicle. The measured peak efficiency is 66.0% FC stack and 63.7% FC system with an idle hydrogen flow rate of 4.39 g/hr. The high FC system efficiencies at low loads match typical vehicle power spectrums, resulting in a high average vehicle efficiency of 62% compared to 45% and 23% for a hybrid electric vehicle and a conventional vehicle, respectively. An energy breakdown accounts for the FC stack losses, FC system losses, air compressor loads, and heater loads for different drive cycles and different thermal conditions. The cold-start North American city drive cycle (UDDS) energy consumption values are, respectively, 758, 581, 226, and 321 Wh/km at ambient conditions of -18 degrees C, -7 degrees C, -25 degrees C and 35 degrees C with 850 W/m 2 of solar loading. The FC system shutdown and startup processes at temperatures below the freezing point contribute to the increased hydrogen consumption. Additionally, the raw test data files are available for download, thus providing the research community with a public reference data on a modern production automotive FC system.

08 HYDROGEN↗

Life cycle assessment of coir fiber-reinforced composites for automotive applications

Past decades have seen an increasing prevalence of natural fiber-reinforced composites (NFRCs) due to growing conscientiousness around sustainability and a push towards vehicle lightweighting. The environmentally friendly and sustainable claims of NFRCs need to be validated due to their large variability and variety, particularly where material substitutions are concerned, such as in substituting glass fiber with natural fiber. Additionally, the objective of this work is to determine the cumulative energy demand (CED) and greenhouse gas emissions (GHG) associated with an automotive part (of volume 0.001 m3) made from 40 wt% coir fiber-reinforced polypropylene (PP) and compared with a similar part made from 40 wt% glass fiber reinforced PP. SimaPro v. 9.0.0.49 was used for the analysis, whereas inventory data were collected from databases, such as Ecoinvent 3, Transportation Energy Databook, Greet model 2022, and published papers. The results showed that CED and GHG associated with the coir fiber-reinforced composite part were lower than the glass fiber-reinforced composite part for both cradle-to-gate (~34–40%) and cradle-to-grave (excluding end-of-life) (~24%) analysis.

36 MATERIALS SCIENCE↗

Performance and cost of automotive fuel cell systems with ultra-low platinum loadings.

An automotive polymer-electrolyte fuel cell (PEFC) system with ultra-low platinum loading (0.15 mg-Pt cm{sup -2}) has been analyzed to determine the relationship between its design-point efficiency and the system efficiency at part loads, efficiency over drive cycles, stack and system costs, and heat rejection. The membrane electrode assemblies in the reference PEFC stack use nanostructured, thin-film ternary catalysts supported on organic whiskers and a modified perfluorosulfonic acid membrane. The analyses show that the stack Pt content can be reduced by 50% and the projected high-volume manufacturing cost by >45% for the stack and by 25% for the system, if the design-point system efficiency is lowered from 50% to 40%. The resulting penalties in performance are a <1% reduction in the system peak efficiency; a 2-4% decrease in the system efficiency on the urban, highway, and LA92 drive cycles; and a 6.3% decrease in the fuel economy of the modeled hybrid fuel-cell vehicle on the combined cycle used by EPA for emission and fuel economy certification. The stack heat load, however, increases by 50% at full power (80 kW{sub e}) but by only 23% at the continuous power (61.5 kW{sub e}) needed to propel the vehicle on a 6.5% grade at 55 mph. The reduced platinum and system cost advantages of further lowering the design-point efficiency from 40% to 35% are marginal. The analyses indicate that thermal management in the lower efficiency systems is very challenging and that the radiator becomes bulky if the stack temperature cannot be allowed to increase to 90-95 C under driving conditions where heat rejection is difficult.

30 DIRECT ENERGY CONVERSION↗

Property optimized energy absorber for automotive bumpers utilizing multi-material and structural design strategies

This study proposes a novel design for automotive bumper using optimized lattice structures and multi-materials to balance low-speed collision and high-speed pedestrian impact performance. Different blends of 20 % carbon fiber-reinforced acrylonitrile butadiene styrene with thermoplastic polyurethane were used to tailor material properties. The energy absorber features lattice structures with customized mechanical responses, created by varying the incline angle θ from 0 to 180°. We conducted 576 finite element simulations on a half-scale model to optimize energy absorption and stiffness, leading to 66 optimized designs that met both low-speed and high-speed impact criteria. Two sub-scale optimized energy absorbers with different peak forces—both meeting low-speed impact requirements—were 3D printed and validated through drop-weight testing. The one with lower peak stress demonstrated a more compliant response, exhibiting approximately 90 % lower initial peak force and an increase in energy absorption of around 33 % (from 24 J to 32 J). Compared to the baseline triangular lattice, the optimized absorber increased energy absorption by 68 % from (19 J to 32 J) and reduced peak stress by 70 %. It also showed near-complete recovery with minimal fractures, making it suitable for repeated use. This design improves safety while offering a lightweight, durable, and cost-effective bumper system.

36 MATERIALS SCIENCE↗

Materials Engineering and Scale Up of Fluid Phase Chemical Hydrogen Storage for Automotive Applications

Among candidates for chemical hydrogen storage in PEM fuel cell automotive applications, ammonia borane (AB, NH3BH3) is considered to be one of the most promising materials due to its high hydrogen content of 14-16 wt% below 200°C and high volumetric density. In our previous paper, we selected AB in silicone oil as a role model for a slurry hydrogen storage system. Materials engineering properties were optimized by increasing solid loading by using an ultra-sonic process. In this paper, we proceeded to scale up to liter size batches with solid loadings up to 50 wt% (8 wt% H2) with dynamic viscosities less than 1000cP at 25°C. The use of a non-ionic surfactant, Triton X-15, shows significant promise in controlling the level of foaming produced during the thermal dehydrogenation of the AB. Through the development of new and efficient processing techniques and the ability to adequately control the foaming, stable homogenous slurries of high solid loading have been demonstrated as a viable hydrogen delivery source.

ammonia borane↗

Characterizing automotive fuel cell materials by soft x-ray scanning transmission x-ray microscopy

Proton-Exchange Membrane Fuel Cell (PEM-FC) based engines are being developed rapidly for near-term implementation in hydrogen fueled, mass production, personal automobiles. Research is focused on understanding and controlling various degradation processes (carbon corrosion, Pt migration, cold start), and reducing cost by reducing or eliminating Pt catalyst. We are using soft X-ray scanning transmission X-ray microscopy (STXM) at the S 2p, C 1s, O 1s and F 1s edges to study a variety of issues related to optimization of PEM-FC materials for automotive applications. A method to efficiently and accurately measure perfluorosulfonic acid distributions was developed and is being used to better understand how different loadings and preparation methods affect the ionomer distribution in the cathode. Progress towards an environmental cell capable of controlling the temperature and humidity of a PEM-FC sample in the STXM is described. Methods for studying the 3D chemical structure of PEM-FC are outlined.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Evaluation of Performance and Opportunities for Improvements in Automotive Power Electronics Systems: Preprint

Thermal management strategies for automotive power electronic systems have evolved over time to reduce system cost and to improve reliability and thermal performance. In this study, we characterized the power electronic thermal management systems of two electric-drive vehicles--the 2012 Nissan LEAF and 2014 Honda Accord Hybrid. Tests were conducted to measure the insulated-gate bipolar transistor-to-coolant thermal resistances for both steady-state and transient conditions at various coolant flow rates. Water-ethylene glycol at a temperature of 65 degrees C was used as the coolant for these experiments. Computational fluid dynamics and finite element analysis models of the vehicle's power electronics thermal management system were then created and validated using experimentally obtained results. Results indicate that the Accord module provides lower steady-state thermal resistance as compared with the LEAF module. However, the LEAF design may provide improved performance in transient conditions and may have cost benefits.

30 DIRECT ENERGY CONVERSION↗

Electrohydraulic Forming of Sheet Metal for Structural Automotive Applications - PNNL CRADA 258 Project Letter Agreement 1

This project focused on developing, characterizing, and commercializing electrohydraulic forming of sheet metal for structural automotive applications. Pulsed electrohydraulic forming is an electrodynamic process based upon high-voltage discharge of capacitors between two electrodes positioned in a fluid-filled chamber. The electrical discharge results in the vaporization of a small volume of the liquid, which creates a high-intensity, high-velocity shock wave in the liquid. The shock wave is directed toward a sheet metal workpiece, which is ultimately driven into a die.

aluminum↗

Development of High Speed Multispectral Imaging for Sorting Automotive Plastics, Phase II Final Report

The objective of this Small Business Innovation Research Phase II project is to develop an infrared (IR) hyperspectral imaging system suitable for recycling end-of-life automotive plastics due to rapid, concurrent identification of multiple samples according to their polymer types. This Phase II research has contributed greatly to the development of a prototype sorting unit. Techniques developed from this technology are already in use in multiple installations worldwide. RT investigated various approaches to identification and sorting of the polymers. Some approaches were determined to be unsuitable for the current application. Multiple approaches were determined to be suitable, however a hyperspectral imaging system utilizing a single high speed camera with full spectral capability looking over the entire waste stream width has been selected.

47 OTHER INSTRUMENTATION↗

Technical Assessment of Compressed Hydrogen Storage Tank Systems for Automotive Applications

This technical report describes DOE's assessment of the performance and cost of compressed hydrogen storage tank systems for automotive applications. The on-board performance (by Argonne National Lab) and high-volume manufacturing cost (by TIAX LLC) were estimated for compressed hydrogen storage tanks. The results were compared to DOE's 2010, 2015, and ultimate full fleet hydrogen storage targets. The Well-to-Tank (WTT) efficiency as well as the off-board performance and cost of delivering compressed hydrogen were also documented in the report.

08 HYDROGEN↗

High-Strength Electroformed Nanostructured Aluminum for Lightweight Automotive Applications

This is the final technical report on the development of nanostructured light weight aluminum alloys for automotive applications. We describe the use of thermodynamically stabilized aluminum alloys and the processes used to create them electrolytically. The alloy is strong and ductile with strengths of 680 MPa and ductility greater than 8%. The material currently produces a cost impact of $4.5 per pound saved with a roadmap to get to $2 per pound saved.

36 MATERIALS SCIENCE↗

Coatings and Process Development for Reduced Energy Automotive OEM Manufacturing Final Technical Report

The project team successfully developed a new low-temperature coating system that achieves performance, durability, and appearance requirements for an Automotive Original Equipment Manufacturer paint system. This coating system is compatible with current OEM manufacturing paint lines, allowing application to existing manufacturing locations. The new coating system can also save capital expenses for new lines or renovations of existing lines. The new paint system enable energy savings and operational expense savings. DURR has designed a reference system that can serve as the starting point for new or retrofit paint line upgrades to this low temperature coating system. NDSU has developed and demonstrated the value of high-throughput screening for polymers and cure performance.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Development and Integration of Predictive Models for Manufacturing and Structural Performance of Carbon Fiber Composites in Automotive Applications (Final Report)

The goal of this project is to develop integrated, state-of-the-art, computational modeling tools based on an integrated computational materials engineering (ICME) methodology that are critically needed to enable structural carbon fiber (CF) applications in automobiles. These tools are designed to predict the manufacturing and structural performance of CF composites, including stochastic effects. During the first phase of the project, the manufacturing and structural performance tools, including a stochastic driver, were developed, calibrated, and validated against coupon and component level test results. For this project, from the manufacturing side, the development efforts were focused on high-pressure resin transfer molding (HP-RTM), a potentially game-changing manufacturing technology that is capable of reaching the 3-5-minute cycle time that is necessary for volume manufacturing of composites. On the structural performance side, the crashworthiness of CF structures was studied. Accordingly, computational tools were developed and validated. The resulting differences between the numerical predictions and the experimental results in the first phase of the project were required to be less than 15%. During the second phase of the project, the manufacturing and performance tools were integrated by mapping the manufacturing outcomes (e.g., fiber angles, residual stresses, degree of cure, and defects) into the structural models. Also, using the tools developed in this project, an automotive assembly currently manufactured in steel (2016 GM Malibu) was redesigned to be manufactured using advanced CF composites with the objective of comparing the performance of the CF assembly with the developed ICME model predictions. The weight, performance and cost of the CF assembly were compared with the baseline steel assembly as well. The CF underbody design was shown to be 30% lighter than the corresponding steel design. The CF underbody assembly withstood the side pole impact with less than half the intrusion for the steel assembly. Excellent correlations within 10% for both peak impact load and intrusion were observed between the numerical predictions and experimental results. Based on the cost models developed in the project, the cost increase per Kg saved was determined to be $22. The project team has prepared a total of 28 publications in various journals and conferences and broadly communicated the project results for the benefit of the composite industry. The project team has also prepared a total of 10 patent applications that were submitted to the US Patent and Trademark office.

36 MATERIALS SCIENCE↗

Future Automotive Systems Technology Simulator (FASTSim) Validation Report - 2021

The National Renewable Energy Laboratory's Future Automotive Systems Technology Simulator (FASTSim) captures the most important factors influencing vehicle power demands and performs large-scale fuel efficiency calculations very quickly. These features make FASTSim well suited to evaluate a representative distribution of real-world fuel efficiency over a large quantity of in-use driving profiles, which have become increasingly available in recent years owing to incorporation of Global Positioning System data collection into various travel surveys and studies. In addition, by being open source, computationally lightweight, freely available, and free from expensive third-party software requirements, analyses conducted using FASTSim may be easily replicated and critiqued in an open forum. This is highly desirable for situations in which technical experts seek to reach consensus over questions about what vehicle development plans or public interest strategies could maximize fuel savings and minimize adverse environmental impacts with an evolving vehicle fleet. While FASTSim continues to be refined and improved on an ongoing basis, this report compiles available runs using versions of the tool from the past few years to provide illustrative comparisons of the model results against measured data.

33 ADVANCED PROPULSION SYSTEMS↗

Development of NDE/NDT Tools for High-Volume & High-Speed Inspection of CFRP Structures in Automotive Manufacturing

Main advantages of the air-coupled ultrasound testing (ACUT) and electromagnetic testing (EMT) techniques for NDE of CFRP composites were non-contact sensing, scalability for high-speed inspection, cost-effectiveness, and non-hazardous operation. Despite these advantages, no systems that would satisfy the project requirements were commercially available. Hence, one of the major efforts of the Michigan State University (MSU) team at the initial stage of the project was to close this technological gap by developing, optimizing, and validating array sensors that would provide sufficient sensitivity, spatial coverage, and resolution for robust defect detection. Optimization of the ACUT and EMT sensor designs was performed using experimentally validated finite element models. Initial experiments using array probes were conducted on relatively flat CFRP samples. In parallel, the MSU team designed and assembled a portable platform with two robotic arms. The robots were equipped with newly designed sensors that enabled high-speed NDE of curved CFRP parts. Presently, the developed robotic platform can be used as a demo/template NDE system, which is easily adaptable to manufacturing environments and in-line NDE. The ACUT NDE system developed by the MSU team used a high-power 4-channel pulser receiver for parallel data acquisition. The array probes were designed by stacking commercially available ACUT transducers, which operated in the frequency range between 100 kHz and 500 kHz. MSU optimized the excitation procedure and developed wave focusing cones so as to reduce the crosstalk between the transducers and to provide higher pulse repletion frequency (PRF). The through-transmission (TT) and single-side access (SSA) inspection modes were successfully implemented. In the TT-ACUT, structural defects in CFRP were detected by passing ultrasonic waves through the test part. Hence, the ACUT transmitters and receivers needed to be placed on the opposite sides of the test part. In the SSA-ACUT, guided waves (GW) were excited in the test part using the transmitters and were sensed by the receivers from the same side. Multi-channel TT-ACUT and SSA-ACUT provided high-speed NDE, and were successfully validated on CFRP test samples with interlaminar delaminations and other embedded defects The EM techniques developed by the MSU team included: 1) eddy current testing (ECT), 2) capacitive imaging (CI) and hybrid dual-mode imaging. In ECT, structural damage was detected in CFRP using coils sensor arrays. In ECT, the excitation magnetic field is generated by passing an alternating current through a coil, which is placed above the test sample. The excitation field penetrates the conductive sample and induces the eddy currents in its transect. In turn, the eddy currents generate the reaction field, which affects the total field sensed by a coil. Hence, the presence of structural flaws will alter the eddy current flow and the picked-up signal. ECT is mostly sensitive to local changes of the electric conductivity of the test sample, and CFRPs are mostly conductive in the direction of carbon fibers. Hence, ECT was well suited for the detection of fiber damage/fiber irregularities. The MSU team developed printed circuit boards (PCB) with coil sensor arrays optimized for NDE of CFRP. Unlike most commercial probes designed for ECT of metallic structures, the MSU array probes were designed for operation in [1-10] MHz frequency range, which was optimal for low-conductive CFRP. Multiple sensing topologies (coil groups excitation/sensing arrangements) were implemented and successfully validated. Capacitive Imaging (CI) technique developed by MSU was complementary to ECT. In contrast to ECT, which was sensitive to local changes of the electrical conductivity, the CI was sensitive to local changes of the dielectric constant. Therefore, CI could provide information about matrix damage/matrix irregularities in CFRP. The MSU CI sensor arrays were made of multiple circular or rectangular open-plate capacitors printed on PCB. Sensors of this type are not commercially available. In addition to ECT and CI, the MSU team developed a hybrid (dual-mode) inductive/capacitive measurement technique that synergistically combined the benefits of inductive and capacitive sensing for rapid NDE of fiber reinforced polymer (FRP) composite structures. Fiber damage and fiber irregularities in FRPs were detected by configuring hybrid sensors as coil sensors. Similarly, matrix damage, matrix irregularities and interlaminar delaminations were detected by configuring hybrid sensors as capacitive sensors. ECT and CI were performed sequentially by means of electronic switching. Hence, eliminating the need for mounting two separate sensor arrays on the probe. Portable robotic platform was developed by MSU for multi-technique high-speed NDE of CFRP test parts. The platform had two 6-axis robots, which enabled inspection of curved parts in approximately a 6×6×6 ft 3 active scan area. On the software side, the MSU team integrated scripts for NDE hardware control with scripts for robot motion control. MSU also implemented automated path planning for the robots, reconstruction of part’s surfaces via stereovision, 3D rendering of inspection data, and image processing algorithms for enhanced defect detection. Automotive composite parts manufactured by Plasan Composites from Phase I were used to validate the ACUT and EMT techniques on representative testbeds. Among those parts were three X-braces for a Dodge Viper, one composite calibration plaque with known defects at known locations, and four other test sections, including sections from a front splitter, a corner section from a composite hood, and a high-pressure RTM panel made using non crimp fabric. Other test samples included CFRP and GFRP calibration plates with fiber/matrix defects fabricated at MSU/CVRC.

36 MATERIALS SCIENCE↗

Federal Automotive Statistical Tool: FY 2022 Data Call Status & Review Tools [Slides]

This presentation presents an overview of current federal vehicle fleet current data collection efforts covering required information submissions about the motor vehicles, fueling centers, and electric vehicle supply equipment (EVSE) inventory through the Federal Automotive Statistical Tool (FAST). The presentation also provides an overview of the capabilities within FAST to assist federal agency users with reviewing and improving the quality of their fleet data submissions. This presentation is intended for delivery via WebEx at the November 9, 2022 meeting of the DOE-sponsored INTERFUEL working group. FAST is a web-based information management tool developed by INL and funded by GSA's Office of Government-wide Policy and DOE's Federal Energy Management Program.

33 ADVANCED PROPULSION SYSTEMS↗