Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Aircraft airspeed”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8
All sourcesNASA NTRSDOE OSTI
NASA NTRS1974

Flight experience with the decelerating noise abatement approach

The noise of older aircraft can be reduced in two principal ways: retrofitting the aircraft with a quiet propulsion system, and changing the flight operational procedures used in flying the aircraft. The former approach has already proved to be expensive, time consuming, and difficult to implement even though low-noise propulsion system technology exists. The latter method seems to hold promise of being less expensive and easier to implement. One operational technique which might reduce the noise beneath the landing approach path is the decelerating approach. This technique requires intercepting the 3 deg approach path at a relatively high speed with the aircraft in the cruise configuration, then reducing the thrust to idle and allowing the aircraft to decelerate along the 3 deg approach path. As the appropriate airspeed is achieved, the landing flaps and landing gear are deployed for a normal flare and landing. Because the engines, which are the predominant noise source on landing approach, are at idle thrust, a significant reduction in the noise beneath the approach path should be realized.

Putman, T. W.↗
NASA NTRS1980

Atmospheric laser Doppler velocimetry - An overview

Research, development, and application of atmospheric laser Doppler velocimetry are overviewed. Consideration is given to operation principles of CO2 heterodyne systems. Global wind, pollution, V/STOL flow, and true airspeed measurements are outlined. Wind energy, dust devils, water spouts, tornadoes, and aircraft wake vortices are covered.

Bilbro, J. W.↗
NASA NTRS1961

Sound Pressures and Correlations of Noise on the Fuselage of a Jet Aircraft in Flight

Tests were conducted at altitudes of 10,000, 20,000, and 30,000 feet at speeds of Mach 0.4, 0.6, and O.8. It was found that the sound pressure levels on the aft fuselage of a jet aircraft in flight can be estimated using an equation involving the true airspeed and the free air density. The cross-correlation coefficient over a spacing of 2.5 feet was generalized with Strouhal number. The spectrum of the noise in flight is comparatively flat up to 10,000 cycles per second.

Shattuck, Russell D.↗
NASA NTRSDate not supplied

Uncertainty Propagation in Pre-Flight Prediction of Unmanned Aerial Vehicle Separation Violation

Current forecasts on the future of aeronautics suggest an in- creasing number of unmanned aerial vehicles entering the low- altitude airspace in the next decades (FAA, 2018; Kopardekar et al., 2016). Small vehicles for package delivery as well as larger vehicles for urban air mobility will change the airspace drastically, increasing density of operations both in time, i.e. high number of take-off and landings per unit time, and in space, operating in dense urban environment. This scenario poses challenges to the current approach to air traffic control, and large efforts from academia, industry and regulatory bodies are dedicated to the development of new traffic management strategies that leverage higher computing and simulating capabilities available today. In this paper, we propose a simple look-ahead approach to predict potential minimum separation violations at the strategic level, that is before vehicles start flying, depending on the predefined 4D trajectories and uncertainty affecting the wind acting along those routes. The wind field is extracted from the NOAA North America Mesoscale Forecast System and interpolated using Gaussian process regression, while uncertainty affecting the expected cruise airspeed is propagated through error intervals. The approach allows the prediction of aircraft separation as a function of time, highlighting potential safety violations that would go undetected if uncertainty affecting the expected 4D trajectories is not considered. The paper will also discuss issues related to accuracy and scalability of the approach to multiple vehicle operations.

Trajectory Prediction↗
NASA NTRS1978

Investigation of interior noise in a twin-engine light aircraft

This paper describes experimental studies of interior noise in a twin-engine, propeller-driven, light aircraft. An analytical model for this type of aircraft is also discussed. Results indicate that interior noise levels in this aircraft due to propeller noise can be reduced by reducing engine rpm at constant airspeed (about 3 dB), and by synchrophasing the twin engines/propellers (perhaps up to 12 dB). Ground tests show that the exterior noise pressure imposed on the fuselage consists of a complex combination of narrow-band harmonics due to propeller and engine exhaust sources. This noise is reduced by about 20-40 dB (depending on the frequency) by transmission through the sidewall to the cabin interior. The analytical model described uses modal methods and incorporates the flat-side geometrical and skin-stringer structural features of this light aircraft.

Mixson, J. S.↗
NASA NTRS1975

Fixed-range optimum trajectories for short-haul aircraft

An algorithm, based on the energy-state method, is derived for calculating optimum trajectories with a range constraint. The basis of the algorithm is the assumption that optimum trajectories consist of, at most, three segments: an increasing energy segment (climb); a constant energy segment (cruise); and a decreasing energy segment (descent). This assumption allows energy to be used as the independent variable in the increasing and decreasing energy segments, thereby eliminating the integration of a separate adjoint differential equation and simplifying the calculus of variations problem to one requiring only pointwise extremization of algebraic functions. The algorithm is used to compute minimum fuel, minimum time, and minimum direct-operating-cost trajectories, with range as a parameter, for an in-service CTOL aircraft and for an advanced STOL aircraft. For the CTOL aircraft and the minimum-fuel performance function, the optimum controls, consisting of air-speed and engine power setting, are continuous functions of the energy in both climb and descent as well as near the maximum or cruise energy. This is also true for the STOL aircraft except in the descent where at one energy level a nearly constant energy dive segment occurs, yielding a discontinuity in the airspeed at that energy. The reason for this segment appears to be the relatively high fuel flow at idle power of the engines used by this STOL aircraft. Use of a simplified trajectory which eliminates the dive increases the fuel consumption of the total descent trajectory by about 10 percent and the time to fly the descent by about 19 percent compared to the optimum.

Erzberger, H.↗
NASA NTRS1991

Calculation of aerosol backscatter from airborne continuous wave focused CO2 Doppler lidar measurements. I - Algorithm description

Since 1981 the Royal Signals and Radar Establishment and the Royal Aircraft Establishment, United Kindom, have made vertical and horizontal sounding measurements of aerosol backscatter coefficients at 10.6 microns, using an airborne continuous-wave-focused CO2 Doppler lidar, the Laser True Airspeed System (LATAS). In this paper, the heterodyne signal from the LATAS detector is spectrally analyzed. Then, in conjunction with aircraft flight parameters, the data are processed in a six-stage computer algorithm: set search window, search for peak signal, test peak signal, measure total signal, calculate signal-to-noise ratio, and calculate backscatter coefficient.

Rothermel, Jeffry↗
NASA NTRS1990

Control of an aircraft in downbursts

Guidance schemes are designed to approximate the optimal survival and optimal performance paths through downbursts, which were determined in the previous paper. Specifically, climb-rate command following is used to achieve performance, and altitude command following is used to enhance survivability. Nonlinear simulations are conducted to investigate the effects of the climb-rate command and altitude command. Takeoff flight is considered and full thrust is assumed. In a mild to moderate downburst, an aircraft can follow a constant, smaller-than-nominal climb rate without stall. Better survival capability is achieved by climbing at a lower rate accompanied by lower altitude, and vice versa. In a severe downbursts, the aircraft must descend to avoid stall. The farther it descends, the higher the survival capability, but the poorer the performance. If the downburst is very severe, the best strategy is to descend immediately to the lowest safe altitude. Since the intensity of a downbursts is hard to evaluate prior to penetration, it is advisable to keep a high airspeed. Therefore, use of the survival strategy is recommended that employs maximum thrust and allows the aircraft to descend to a safe minimum altitude immediately upon entering a downburst on takeoff.

Zhao, Yiyuan↗
NASA NTRSDate not supplied

Training the Powered-Lift Evaluation Pilot

This poster describes a project to prepare pilots for a study assessing novel aircraft automation concepts for electric Vertical Takeoff and Landing (eVTOL) aircraft using NASA’s Vertical Motion Simulator (VMS). By exploring the operational and learning challenges related to transitioning between forward flight and vertical landing, we seek to establish baselines of pilot workload and aircraft handling qualities across varying atmospheric conditions and automation states. The simulated eVTOL design differentiates flight control allocations as a function of airspeed across four speed ranges as the vehicle transitions between fully thrust-borne lift and wing-borne lift. As speed increases, side stick controls command: translational ground speeds, vertical and lateral acceleration, vertical rate, vertical flight path angle, and bank angle. This novel approach to flight control allocation creates a significant learning challenge for pilots. Since initial eVTOL aircraft may have limitations on hover capabilities, automation and flight guidance cues also vary with airspeed to provide efficient landing profiles while still providing cues suitable for cruise flight. The NASA team prepared the study pilots to follow these flight guidance cues along curved Required Navigation Performance (RNP) approaches and along 6o and 12o glide paths to energy-efficient assistive-hover landing and goarounds. The pre-VMS preparation sought to prepare pilots from diverse levels of experience and background. To do this, NASA researchers designed and developed a fixed-based, large field-ofview simulator with terrain, structures, and air traffic. With one day of combined classroom learning and skill development in the fixedbase simulator, pilots were largely able to fly the simulated eVTOL in the VMS with sufficient mastery to provide handling quality assessments using the Cooper-Harper Handling Qualities Rating and workload assessments through the Bedford Workload Scale.

AAM↗
NASA NTRS1988

Flight evaluation of an integrated control and display system for high-precision manual landing flare of powered-lift STOL aircraft

An account is given of the features and performance of a manual landing flare and touchdown system capable of great precision, as demonstrated by its installation in the NASA Quiet Short-haul Research Aircraft (QSRA). The integrated cockpit display and closed-loop control employed constitutes a trajectory-augmentation system that extends QSRA flight control from augmentation of altitude, flight path angle, and airspeed, to the augmentation of the trajectory itself. The + or - 18 ft touchdown dispersion achieved is approximately equal to that obtained during aircraft carrier trials of the same aircraft.

Hynes, Charles S.↗
NASA NTRS1979

Flight test evaluation of predicted light aircraft drag, performance, and stability

A technique was developed which permits simultaneous extraction of complete lift, drag, and thrust power curves from time histories of a single aircraft maneuver such as a pull up (from V max to V stall) and pushover (to V max for level flight). The technique, which is an extension of nonlinear equations of motion of the parameter identification methods of Iliff and Taylor and includes provisions for internal data compatibility improvement as well, was shown to be capable of correcting random errors in the most sensitive data channel and yielding highly accurate results. Flow charts, listings, sample inputs and outputs for the relevant routines are provided as appendices. This technique was applied to flight data taken on the ATLIT aircraft. Lack of adequate knowledge of the correct full throttle thrust horsepower true airspeed variation and considerable internal data inconsistency made it impossible to apply the trajectory matching features of the technique.

Smetana, F. O.↗
NASA NTRS2003

TAMDAR Capabilities Development

In this viewgraph presentation, information is provided on a collaboration between NASA, the FAA (Federal Aviation Administration), and NOAA (National Oceanographic and Atmospheric Association), particularly regarding the development of a TAMDAR Sensor system. TAMDAR is envisioned to downlink weather data such as icing, temperature, pressure altitude, humidity, magnetic heading, eddy dissipation rate, true airspeed, dew point, density altitude, and winds at altitude from non-jet aircraft. The weather data will be sent to FSL (Forecast Systems Laboratory), FSS (Flight Service Station), ATC (Air Traffic Control), AWC (Aviation Weather Center), and others via a ground-based infrastructure and to other aircraft. New weather products will be generated and uplinked to the cockpit.

Daniels, Taumi↗
NASA NTRS2016

Comparison of Fuel Consumption of Descent Trajectories Under Arrival Metering

This paper compares fuel consumption of descent trajectories from cruise altitude to meter fix when the required time of arrival is later than the nominal time of arrival at the meter fix. The required delay, which is the difference between the nominal and the required times of arrival, is achieved by either slowing down the aircraft in the cruise and descent phases or flying a longer route at a constant altitude. Performance models of ten different Boeing and Airbus aircraft, obtained from the Base of Aircraft Data, are employed for generating the results. It is demonstrated that the most fuel-efficient speed control strategy for absorbing delay is first reducing descent speed as much as possible and then reducing cruise speed. This is a common finding for all ten aircraft considered. For some aircraft, flying at a fixed flight path angle and constant Mach-calibrated-airspeed results in lower fuel consumption compared to standard descent at idle-thrust and constant Mach-calibrated- airspeed. Finally, for the cases examined, it is shown that executing a path stretch maneuver at cruise altitude and descent at a reduced speed is more fuel efficient than inserting an intermediate-altitude cruise segment.

Nikoleris, Tasos↗
NASA NTRS1965

The Effect of Yaw Coupling in Turning Maneuvers of Large Transport Aircraft

A study has been made, using a piloted moving simulator, of the effects of the yaw-coupling parameters N(sub p) and N(sub delta(sub a) on the lateral-directional handling qualities of a large transport airplane at landing-approach airspeed. It is shown that the desirable combinations of these parameters tend to be more proverse when compared with values typical of current aircraft. Results of flight tests in a large variable-stability jet transport showed trends which were similar to those of the simulator data. Areas of minor disagreement, which were traced to differences in airplane geometry, indicate that pilot consciousness of side acceleration forces can be an important factor in handling qualities of future long-nosed transport aircraft.

McNeill, Walter E.↗
DOE OSTI2024

Autonomous Emergency Landing for Fixed-Wing Aircraft with Energy-Constrained Closed-Loop Prediction

Here this paper presents a new approach for autonomous motion planning for aircraft suffering from a loss-of-thrust emergency. Specifically, we show how modifications to the Closed-Loop Rapidly exploring Random Trees (CL-RRT) framework combined with controlled energy dissipation can enable rapid and effective kinodynamic motion planning. This CL-RRT Glide algorithm uses closed-loop prediction not only for node connections but also to estimate the remaining energy and prune infeasible paths. This greatly speeds up the search process, which is essential for emergency situations. In addition, we improve the ability of the gliding aircraft to reach a goal position and energy state. We do so by creating a Dissipative Total Energy Control Scheme (TECS). Dissipative TECS enables the glider to lose excess altitude in order to reach a desired energy level. Simulation results illustrate how the proposed methods enable faster motion planning. We also integrate the system into a small unmanned aerial vehicle system and experimentally demonstrate autonomous glide planning and execution during a motor-failure event. This type of algorithm can primarily benefit unmanned aircraft but can also serve to assist pilots in stressful emergency situations.

42 ENGINEERING↗
NASA NTRS1976

Trailing anemometer for low airspeed calibration

A propeller-type trailing airspeed anemometer system is described for low airspeed (M not exceeding 0.2) calibration which has improved accuracy and is easy to implement as compared to most methods currently in use. The trailing anemometer system consists of the trailing anemometer itself, a deployment mechanism, and an operator's control box. The trailing anemometer is a small low-drag brass body provided with tail fins for self-alignment with the airstream. The rotational speed of a small six-bladed low-inertia propeller is sensed with a miniature self-generating tachometer inside the anemometer. A very satisfactory airspeed calibration can be made with this device in which true airspeed can be measured to within 1 knot. Results from flight calibration of an aircraft and trail-back characteristics of the anemometer and cable are included. The operating speed range of the designed cable-anemometer combination is 7 to 165 knots.

Fisher, B. D.↗