SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Several areas of silicon sheet growth development are addressed including: silicon ingot casting, heat exchanger method, multiwire slicing, and fixed abrasive slicing technique.
The Fixed Abrasive Slicing Techniques (FAST) is a new slicing technique that was developed to slice ingots more effectively. It was demonstrated that 25 wafers/cm can be sliced from 10cm diameter and 19 wafers/cm from 15 cm diameter ingots. Over 99% yield (222 out of a possible 224) was demonstrated during slicing of a 10 cm diameter ingots at 25 wafers/cm. The average thickness of wafers was 0.249 mm and the kerf was 0.151 mm. Slicing rates as high as 0.14 mm/min were also demonstrated for 10 cm diameter ingots.
One of the major cost factors in silicon ingot technology adaptation for terrestrial photovoltaic application is in slicing boules into wafers. The most developed industrial practice is the Internal Diameter (ID) slicing. This method utilizes diamond cutting. The diamond stands up for long periods, hence, the cost of expendable materials is low. However, the ID technology as practiced today has poor material utilization. The Multiblade Slurry (MBS) method has low equipment and labor costs but its expendable material costs are high. Recently Multiwire Slurry (MWS) technology has shown very good material utilization, but its expendable material costs are even higher than MBS. The multiwire Fixed Abrasive Slicing Technique (FAST) still in advanced development stage, combines the low expendable material costs of ID method, the low labor and equipment costs of MBS and high material utilization of MWS.
Slicing is an important processing step for all technologies based on the use of ingots. A comparison of the economics of three slicing techniques shows that the fixed abrasive slicing technique (FAST) is superior to the internal diameter (ID) and the multiblade slurry (MBS) techniques. Factors affecting contact length are discussed, taking into account kerf width, rocking angle, ingot size, and surface speed. Aspects of blade development are also considered. A high concentration of diamonds on wire has been obtained in wire packs usd for FAST slicing. The material removal rate was found to be directly proportional to the pressure at the diamond tips.
Flame retardant, abrasion resistant elastomeric compositions are disclosed which are comprised of thermoplastic polyurethane polymer and flame retarding amounts of a filler selected from decabromodiphenyloxide and antimony oxide in a 3:1 weight ratio, and decabromodiphenyloxide, antimony oxide, and ammonium polyphosphate in a 3:1:3 weight ratio respectively. Heat sealable coated fabrics employing such elastomeric compositions as coating film are produced by dissolving the elastomeric composition to form a solution, casting the solution onto a release paper and drying it to form an elastomeric film. The film is then bonded to a woven, knitted, or felted fabric.
Ceramic coating increases durability and heat resistance of flexible high-temperature insulation. Coating compatible with quartz-fabric insulation allowing it to remain flexible during and after repeated exposures to temperatures of 1,800 degree F (982 degree C). Prevents fabric from becoming brittle while increasing resistance to aerodynamic abrasion and loading. Coating consists of penetrating precoat and topcoat. Major ingredients high-purity colloidal silica binder and ground silica filler, which ensure stability and compatibility with fabric at high temperatures. Both precoat and topcoat cured at room temperature.
A three-phase investigation was conducted to compare the friction and wear response of aluminum and graphite-epoxy composite materials when subjected to loading conditions similar to those experienced by the skin panels on the underside of a transport airplane during an emergency belly landing on a runway surface. The first phase involved a laboratory test which used a standard belt sander to provide the sliding abrasive surface. Small skin-coupon test specimens were abraded over a range of pressures and velocities to determine the effects of these variables on the coefficient of friction and wear rate. The second phase involved abrading I-beam stiffened skins on actual runway surface over the same range of pressures and velocities used in the first phase. In the third phase, large stiffened panels which most closely resembled transport fuelage skin construction were abraded on a runway surface. This report presents results from each phase of the investigation and shows comparisons between the friction and wear behavior of the aluminum and graphite-epoxy composite materials.
The National Aeronautics and Space Administration (NASA) sent a mission to the martian surface, called Mars Pathfinder. The mission payload consisted of a lander and a rover. The primary purpose of the mission was demonstrating a novel entry, descent, and landing method that included a heat shield, a parachute, rockets, and a cocoon of giant air bags. Once on the surface, the spacecraft returned temperature measurements near the Martian surface, atmosphere pressure, wind speed measurements, and images from the lander and rover. The rover obtained 16 elemental measurements of rocks and soils, performed soil-mechanics, atmospheric sedimentation measurements, and soil abrasiveness measurements.
I have the opportunity to work in the Environmental Management Office (EMO) this summer. One of the EMO's tasks is to make sure the Environmental Management System is implemented to the entire Glenn Research Center (GRC). The Environmental Management System (EMS) is a policy or plan that is oriented toward minimizing an organization's impact to the environment. Our EMS includes the reduction of solid waste regeneration and the reduction of hazardous material use, waste, and pollution. With the Waste Management Team's (WMT) help, the EMS can be implemented throughout the NASA Glenn Research Center. The WMT is responsible for the disposal and managing of waste throughout the GRC. They are also responsible for the management of all chemical waste in the facility. My responsibility is to support the waste management team by performing an inventory on parts cleaning stations, abrasive cabinets, and paint booths through out the entire facility. These booths/stations are used throughout the center and they need to be monitored and tested for hazardous waste and material. My job is to visit each of these booths/stations, take samples of the waste, and analyze the samples.
A narrow wire blade with abrasive particles plated within a longitudinally-extending, plated cutting portion that extends from only one side of a wire core and has parallel side walls spaced by a controlled width.
During my summer internship at NASA I have been working alongside the team members of the RESTORE project. Engineers working on the RESTORE project are creating ·a device that can go into space and service satellites that no longer work due to gas shortage or other technical difficulties. In order to complete the task of refueling the satellite a hose needs to be used and covered with a material that can withstand effects of space. The conduit coating abrasion test will help the researchers figure out what type of thermal coating to use on the hose that will be refueling the satellites. The objective of the project is to determine whether or not the conduit coating will withstand the effects of space. For the RESTORE project I will help with various aspects of the testing that needed to be done in order to determine which type of conduit should be used for refueling the satellite. During my time on the project I will be assisting with wiring a relay board that connected to the test set up by soldering, configuring wires and testing for continuity. Prior to the testing I will work on creating the testing site and help write the procedure for the test. The testing will take place over a span of two weeks and lead to an informative conclusion. Working alongside various RESTORE team members I will assist with the project's documentation and records. All in all, throughout my internship at NASA I hope to learn a number of valuable skills and be a part of a hard working team of engineers.
A surface covering composition of abrasion resistant character adapted for disposition in overlying bonded relation to a metal substrate. The surface covering composition includes metal carbide particles within a metal matrix at a packing factor of not less than about 0.6. Not less than about 40 percent by weight of the metal carbide particles are characterized by an effective diameter in the range of +14-32 mesh prior to introduction to the metal matrix. Not less than about 3 percent by weight of the metal carbide particles are characterized by an effective diameter of +60 mesh prior to introduction to the metal matrix.
Deposition of a coating on rough surfaces faces unique challenges due to the complexity of substrate morphology. In the present research, electroless deposition of a Ni-P coating was successfully deposited on diamond particles. Microtomography was conducted to study the deposition mechanisms. It revealed that the coating coverage rate on diamond particles was affected by the synergistic action of the deposition time, substrate morphology, and hypophosphite concentration. The best coverage was achieved in a solution with 0.2 mol/L hypophosphite. Two major morphological features of the coating: nodular and smooth, were influenced by the deposition parameters, coating integrity, and substrate morphology. The failure was seen in fractured and peeled off coatings. It was due to residual stress produced by the coalescing of crystallites during the deposition. This failure mechanism explains the tendency of coating fracture at three morphological features of the substrate. This work is beneficial to semiconductor manufacturing where effective cutting in chip fabrication is essential.
Explore the source record for details and available documents.
Explore the source record for details and available documents.
Explore the source record for details and available documents.
Decreasing LCOE with predictive soiling loss models (using site data to predict annualized energy loss), quantification of different soiling mechanisms (using AFM-based characterization), and developing standards for PV module coatings.