Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “variable selection”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,423 records · Page 79
All sourcesNASA NTRSDOE OSTI
NASA NTRS1989

Spray automated balancing of rotors - How process parameters influence performance

This paper addresses the application of spray-automated balancing of rotors, and the influence that various operating parameters will have on balancing performance. Spray-automated balancing uses the fuel-air repetitive explosion process to imbed short, discrete bursts of high velocity, high temperature powder into a rotating part at an angle selected to reduce unbalance of the part. The shortness of the burst, the delay in firing of the gun, the speed of the disk and the variability in speed all influence the accuracy and effectiveness of the automated balancing process. The paper evaluates this influence by developing an analytical framework and supplementing the analysis with empirical data obtained while firing the gun at a rotating disk. Encouraging results are obtained, and it is shown that the process should perform satisfactorily over a wide range of operating parameters. Further experimental results demonstrate the ability of the method to reduce vibration levels induced by mass unbalance in a rotating disk.

Smalley, A. J.↗
NASA NTRS1990

Mars mission gravity profile simulation

A flight experiment designed to determine the need for artificial gravity for Mars mission architectures at earlier stages of the design process is proposed. The Soviet Mir space station, the NASA Space Shuttle, and the resources of NASA Ames Research Center would be used to duplicate in the terrestrial environment the complete Mars-mission gravity profile in order to assess the need for artificial gravity. All mission phases of 1 G would be on earth; all mission phases of zero or micro G would be in space aboard Mir; and all launch, ascent, orbit, deorbit, approach, departure, and descent G loads would be provided by actual spacecraft in operations that could be designed to simulate the actual G loads, while the Mars stay time would be simulated on earth or in a variable-gravity research facility in space. Methods of simulating activities on the Martian surface are outlined along with data monitoring, countermeasures, and launch site and vehicle selection criteria.

Kuznetz, Lawrence H.↗
NASA NTRS1992

Determination of coronal magnetic fields from vector magnetograms

The determination of coronal magnetic fields from vector magnetograms, including the development and application of algorithms to determine force-free coronal fields above selected observations of active regions is studied. Two additional active regions were selected and analyzed. The restriction of periodicity in the 3-D code which is used to determine the coronal field was removed giving the new code variable mesh spacing and is thus able to provide a more realistic description of coronal fields. The NOAA active region AR5747 of 20 Oct. 1989 was studied. A brief account of progress during the research performed is reported.

Mikic, Zoran↗
NASA NTRS1991

Application of the Galerkin/least-squares formulation to the analysis of hypersonic flows. I - Flow over a two-dimensional ramp

An FEM for the compressible Navier-Stokes equations is introduced. The discretization is based on entropy variables. The methodology is developed within the framework of a Galerkin/least-squares formulation to which a discontinuity-capturing operator is added. Results for three test cases selected among those of the Workshop on Hypersonic Flows for Reentry Problems are presented.

Chalot, F.↗
NASA NTRS1991

Application of the Galerkin/least-squares formulation to the analysis of hypersonic flows. II - Flow past a double ellipse

A finite element method for the compressible Navier-Stokes equations is introduced. The discretization is based on entropy variables. The methodology is developed within the framework of a Galerkin/least-squares formulation to which a discontinuity-capturing operator is added. Results for four test cases selected among those of the Workshop on Hypersonic Flows for Reentry Problems are presented.

Chalot, F.↗
NASA NTRS2003

The NASA Scientific Data Purchase: Summary and Evaluation

This report summarizes the results of the NASA Scientific Data Purchase (SDP) program implemented by the Stennis Space Center Earth Science Application Directorate in fiscal years 1998-2002. The SDP was conducted in support of NASA's Mission to Planet Earth (MTPE) program (currently known as NASA's Earth Science Enterprise). This Earth Science Enterprise (ESE) provides major observational capabilities for NASA's Earth system science research and the U.S. Global Change Research Program. Observations supported through the SDP were selected based upon their application to the five science themes of the MTPE/ESE: 1) Land cover and land use change research; 2) Seasonal to interannual climate variability and prediction; 3) Natural hazards research and applications; 4) Long-term climate: Natural variability and change research; 5) Atmospheric ozone research. The MTPE/ESE science themes, although they have evolved over time, are driven by a set of key science questions that help focus the research program on characterizing the Earth system.

Source record↗
NASA NTRS1994

Optimizaton Methods for Passive Damper Placement and Tunin

The effectiveness of viscous elements in introducing damping in a structure is a function of several variables, including their number, their location in the structure, and their physical properties. This paper addresses the questions of the placement of these elements and the selection of their physical parameters via optimization techniques.

viscous elements↗
NASA NTRS2005

A Rapid Approach to Modeling Species-Habitat Relationships

A growing number of species require conservation or management efforts. Success of these activities requires knowledge of the species' occurrence pattern. Species-habitat models developed from GIS data sources are commonly used to predict species occurrence but commonly used data sources are often developed for purposes other than predicting species occurrence and are of inappropriate scale and the techniques used to extract predictor variables are often time consuming and cannot be repeated easily and thus cannot efficiently reflect changing conditions. We used digital orthophotographs and a grid cell classification scheme to develop an efficient technique to extract predictor variables. We combined our classification scheme with a priori hypothesis development using expert knowledge and a previously published habitat suitability index and used an objective model selection procedure to choose candidate models. We were able to classify a large area (57,000 ha) in a fraction of the time that would be required to map vegetation and were able to test models at varying scales using a windowing process. Interpretation of the selected models confirmed existing knowledge of factors important to Florida scrub-jay habitat occupancy. The potential uses and advantages of using a grid cell classification scheme in conjunction with expert knowledge or an habitat suitability index (HSI) and an objective model selection procedure are discussed.

Carter, Geoffrey M.↗
DOE OSTI2022

A large accessory genome and high recombination rates may influence global distribution and broad host range of the fungal plant pathogen Claviceps purpurea

Pangenome analyses are increasingly being utilized to study the evolution of eukaryotic organisms. While pangenomes can provide insight into polymorphic gene content, inferences about the ecological and adaptive potential of such organisms also need to be accompanied by additional supportive genomic analyses. In this study we constructed a pangenome of Claviceps purpurea from 24 genomes and examined the positive selection and recombination landscape of an economically important fungal organism for pharmacology and agricultural research. Together, these analyses revealed that C. purpurea has a relatively large accessory genome (~ 38%), high recombination rates (ρ = 0.044), and transposon mediated gene duplication. However, due to observations of relatively low transposable element (TE) content (8.8%) and a lack of variability in genome sizes, prolific TE expansion may be controlled by frequent recombination. We additionally identified that within the ergoline biosynthetic cluster the lpsA1 and lpsA2 were the result of a recombination event. However, the high recombination rates observed in C. purpurea may be influencing an overall trend of purifying selection across the genome. These results showcase the use of selection and recombination landscapes to identify mechanisms contributing to pangenome structure and primary factors influencing the evolution of an organism.

59 BASIC BIOLOGICAL SCIENCES↗
NASA NTRS1977

Anion permselective membrane

The objective of NAS 3-20108 was the development and evaluation of improved anion selective membranes useful as efficient separators in a redox power storage cell system being constructed. The program was divided into three parts, (a) optimization of the selected candidate membrane systems, (b) investigation of alternative membrane/polymer systems, and (c) characterization of candidate membranes. The major synthesis effort was aimed at improving and optimizing as far as possible each candidate system with respect to three critical membrane properties essential for good redox cell performance. Substantial improvements were made in 5 candidate membrane systems. The critical synthesis variables of cross-link density, monomer ratio, and solvent composition were examined over a wide range. In addition, eight alternative polymer systems were investigated, two of which attained candidate status. Three other alternatives showed potential but required further research and development. Each candidate system was optimized for selectivity.

Alexander, S.↗
NASA NTRS2012

An Algorithm for Detection of Ground and Canopy Cover in Micropulse Photon-Counting Lidar Altimeter Data in Preparation of the ICESat-2 Mission

The Ice, Cloud and Land Elevation Satellite-II (ICESat-2) mission has been selected by NASA as a Decadal Survey mission, to be launched in 2016. Mission objectives are to measure land ice elevation, sea ice freeboard/ thickness and changes in these variables and to collect measurements over vegetation that will facilitate determination of canopy height, with an accuracy that will allow prediction of future environmental changes and estimation of sea-level rise. The importance of the ICESat-2 project in estimation of biomass and carbon levels has increased substantially, following the recent cancellation of all other planned NASA missions with vegetation-surveying lidars. Two innovative components will characterize the ICESat-2 lidar: (1) Collection of elevation data by a multi-beam system and (2) application of micropulse lidar (photon counting) technology. A micropulse photon-counting altimeter yields clouds of discrete points, which result from returns of individual photons, and hence new data analysis techniques are required for elevation determination and association of returned points to reflectors of interest including canopy and ground in forested areas. The objective of this paper is to derive and validate an algorithm that allows detection of ground under dense canopy and identification of ground and canopy levels in simulated ICESat-2-type data. Data are based on airborne observations with a Sigma Space micropulse lidar and vary with respect to signal strength, noise levels, photon sampling options and other properties. A mathematical algorithm is developed, using spatial statistical and discrete mathematical concepts, including radial basis functions, density measures, geometrical anisotropy, eigenvectors and geostatistical classification parameters and hyperparameters. Validation shows that the algorithm works very well and that ground and canopy elevation, and hence canopy height, can be expected to be observable with a high accuracy during the ICESat-2 mission. A result relevant for instrument design is that even the two weaker beam classes considered can be expected to yield useful results for vegetation measurements (93.01-99.57% correctly selected points for a beam with expected return of 0.93 mean signals per shot (msp9) and 72.85% - 98.68% for 0.48 msp (msp4)). Resampling options affect results more than noise levels. The algorithm derived here is generally applicable for analysis of micropulse lidar altimeter data collected over forested areas as well as other surfaces, including land ice, sea ice and land surfaces.

Herzfeld, Ute C.↗
NASA NTRS1997

A New Approach to Extreme Value Estimation Applicable to a Wide Variety of Random Variables

Designing reliable structures requires an estimate of the maximum and minimum values (i.e., strength and load) that may be encountered in service. Yet designs based on very extreme values (to insure safety) can result in extra material usage and hence, uneconomic systems. In aerospace applications, severe over-design cannot be tolerated making it almost mandatory to design closer to the assumed limits of the design random variables. The issue then is predicting extreme values that are practical, i.e. neither too conservative or non-conservative. Obtaining design values by employing safety factors is well known to often result in overly conservative designs and. Safety factor values have historically been selected rather arbitrarily, often lacking a sound rational basis. To answer the question of how safe a design needs to be has lead design theorists to probabilistic and statistical methods. The so-called three-sigma approach is one such method and has been described as the first step in utilizing information about the data dispersion. However, this method is based on the assumption that the random variable is dispersed symmetrically about the mean and is essentially limited to normally distributed random variables. Use of this method can therefore result in unsafe or overly conservative design allowables if the common assumption of normality is incorrect.

Holland, Frederic A., Jr.↗
NASA NTRS1992

OSSE spectral analysis techniques

Analysis of the spectra from the Oriented Scintillation Spectrometer Experiment (OSSE) is complicated because of the typically low signal to noise (approx. 0.1 percent) and the large background variability. The OSSE instrument was designed to address these difficulties by periodically offset-pointing the detectors from the source to perform background measurements. These background measurements are used to estimate the background during each of the source observations. The resulting background-subtracted spectra can then be accumulated and fitted for spectral lines and/or continua. Data selection based on various environmental parameters can be performed at various stages during the analysis procedure. In order to achieve the instrument's statistical sensitivity, however, it will be necessary for investigators to develop a detailed understanding of the instrument operation, data collection, and the background spectrum and its variability. A brief description of the major steps in the OSSE spectral analysis process is described, including a discussion of the OSSE background spectrum and examples of several observational strategies.

Purcell, W. R.↗
NASA NTRS1994

Overview of the Oregon Transect Ecosystem Research Project

The Oregon Transect Ecosystem Research (OTTER) project is a study of ecosystem functions in coniferous forests using the methods of computer modeling, experimental and theoretical remote sensing, and ecological field and laboratory techniques. The study is focused on predicting the major fluxes of carbon, nitrogen, and water, and the factors that dynamically regulate them. The OTTER project was conceived to test two major questions: (1) Can a generalized ecosystem simulation model, designed to use mainly parameters available from remote sensing, predict the functioning of forests across an environmentally variable region? and (2) To what extent can the variables required by this model be derived from remotely sensed data? The scientific objectives and scope of the project demanded that a coordinated effort be made to link ground measurements with remote sensing and modeling requirements. OTTER was selected as a focus for a National Aeronautics and Space Administration (NASA)-sponsored Multi-sensor Aircraft Campaign (MAC; combining NASA aircraft and sensors with those of others) on the basis of experience gained in past ecosystem studies and remote-sensing projects, and the importance of the OTTER objectives to NASA's long-range science goals and plans. Having several independent approaches available, both on the ground and from various remote-sensing platforms, proved valuable in estimating and validating many of the critical variables. This experience and cross comparison should help simplify future studies of a similar nature. Edited data sets from the OTTER project are now available to the scientific community on optical disks or via on-line data banks at NASA (Washington, D.C., USA) and Oregon State University (Corvallis, Oregon, USA).

Peterson, David L.↗
NASA NTRS1999

Characterization of the Heat Extraction Capability of a Compliant, Sliding, Thermal Interface for Use in a High Temperature, Vacuum Microgravity Furnace

Much of the material science gained in microgravity research requires processing a sample in a high performance furnace. One such furnace currently being designed is the Quench Module Insert (QMI). The Principle Investigators, for whom the furnace is proposed, require high temperature gradients in their cylindrical samples to achieve the science objectives. One of the components critical to achieving high sample axial temperature gradients in the Quench Module Insert is a high performance cold zone to extract the heat from the sample. This cold zone employs a compliant, sliding thermal interface based on a Vel-Therm felt. This felt provides a conductive path between the Sample Cartridge Assembly (SCA) exterior surface and the interior surface of the water cooled chill block while allowing movement of the sample relative to the chill block. The Vel-Therm felt is composed of long polymer-based fibers affixed to a thin flexible substrate layer. The fibers are oriented perpendicular to this substrate giving the felt the appearance of a velvet fabric. The Vel-Therm felt heat extraction capability was quantified in earlier tests performed in an inert gas environment. The current activity, described in this paper, is intended to characterize the extraction capability of Vel-Therm felt in a vacuum environment similar to the QMI environment. This testing is necessary to quantify the thermal performance of the Vel-Therm felt and the sensitivity of that performance to key variables. The data derived from these tests will be incorporated into the current thermal models to improve the quality of the models and reduce uncertainty of the analytical results. In addition, the data will be used to help select the appropriate Vel-Therm felt and set proper operating limits as well as assess the performance range of the furnace. The objective of this test is to measure the heat extraction rate of the Vel-Therm felt as specified by the effective heat transfer coefficient. Therefore, the test setup was designed to force the bulk of the heat transfer through the area where the Vel-Therm felt was applied. A heat source, consisting of a ceramic heating element encased in a Copper (Cu) housing is mounted on four isolated support rods. A 6-layer molybdenum radiation shield is used to insulate against heat loss from the heater and prevent heat exchange between the hot and cold sides of the test apparatus. The Vel-Therm felt is affixed to the surface of the cold sink, a water-cooled Cu chill block. An adjustable plate supports and isolates the cold sink from above and is used to control the amount of the deflection of the Vel- Therm when in contact with the Cu heating element housing. The primary means of establishing the power being conducted through the felt is to measure the energy being transferred to the water passing through the chill block. Analysis was performed to support the assumption that the source and sink surfaces were approximately isothermal under the specific test conditions. As a check on the amount of power passing through the felt, the power supplied to the heater was also measured. Thermocouples were strategically located throughout the test apparatus for measurement purposes. A bell jar was lowered over the assembly to impose vacuum conditions. Currently, variables tested have been fiber compression and fiber type and surface temperatures (both the hot and cold side temperatures are hypothesized to be important to the performance of the Vel-Therm.) Selected runs were repeated to ensure consistency and repeatability. Results obtained thus far reveal that Vel-Therm performance is significantly degraded by fibers being exposed to high compression. It also shows that performance is somewhat negatively impacted by previous compression, thereby, raising the question of repeatability. In addition, early results show a significant dependence on temperature. A computer aided mathematical analysis of the test setup is ongoing. The results will be correlated to actual results. The correlation will examine such details as parasitic loses, conduction down the power leads and many other concerns.

Bellomy-Ezell, Jenny↗
DOE OSTI2024

Relevant biochar characteristics influencing compressive strength of biochar-cement mortars

To counteract the contribution of CO 2 emissions by cement production and utilization, biochar is being harnessed as a carbon-negative additive in concrete. Increasing the cement replacement and biochar dosage will increase the carbon offset, but there is large variability in methods being used and many researchers report strength decreases at cement replacements beyond 5%. This work presents a reliable method to replace 10% of the cement mass with a vast selection of biochars without decreasing ultimate compressive strength, and in many cases significantly improving it. By carefully quantifying the physical and chemical properties of each biochar used, machine learning algorithms were used to elucidate the three most influential biochar characteristics that control mortar strength: initial saturation percentage, oxygen-to-carbon ratio, and soluble silicon. These results provide additional research avenues for utilizing several potential biomass waste streams to increase the biochar dosage in cement mixes without decreasing mechanical properties.

97 MATHEMATICS AND COMPUTING↗
NASA NTRS2003

Discoveries about Tropical Tropospheric Ozone from Satellite and SHADOZ (Southern Hemisphere Additional Ozonesondes) and a Future Perspective on NASA's Ozone Sensors

We have been producing near-real tropical tropospheric ozone ('TTO') data from TOMS since 1997 with Prof. Hudson and students at the University of Maryland. Maps for 1996-2000 for the operational Earth-Probe instrument reside at: . We also have archived 'TTO' data from the Nimbus 7/TOMS satellite (1979-1992). The tropics is a region strongly influenced by natural variability and anthropogenic activity and the satellite data have been used to track biomass burning pollution and to detect interannual variability and climate signals in ozone. We look forward to future ozone sensors from NASA; four will be launched in 2004 as part of the EOS AURA Mission. The satellite view of chemical-dynamical interactions in tropospheric ozone is not adequate to capture vertical variability. Thus, in 1998, NASA's Goddard Space Flight Center, NOAA's Climate Monitoring and Diagnostics Laboratory (CMDL) and a team of international sponsors established the SHADOZ (Southern Hemisphere ADditional OZonesondes) project to address the gap in tropical ozone soundings. SHADOZ augments launches at selected sites and provides a public archive of ozonesonde data from twelve tropical and subtropical stations at http://croc.nsfc.nasa.gov/shadoz. The stations are: Ascension Island; Nairobi, Kenya; Irene, South Africa; R,union Island; Watukosek, Java; Fiji; Tahiti; American Samoa; San Cristobal, Galapagos; Natal, Brazil, Malindi, Kenya; Paramaribo, Surinam. From the first 3-4 years of data (presently greater than 1700 sondes), the following features emerge: (a) highly variable tropospheric ozone; (b) a zonal wave-one pattern in tropospheric column ozone; (c) tropospheric ozone variability over the Indian and Pacific Ocean displays strong convective signatures.

Thompson, Anne↗
NASA NTRS2005

Role of Probabilistic Micromechanics Modeling in Establishing Design Allowables in Composites

One of the major challenges in designing with any new material, and particularly with advanced composite materials, is the fidelity of material design allowables. In the case of composite materials, the concern arises from the inherent nature of these materials, i.e., their heterogeneous make-up and the various factors that affect their properties in a specific design environment. Composites have various scales - micro, macro, laminate and structural, as well as numerous other fabrication related parameters. Many advanced composites in aerospace applications involve complex two- and three-dimensional fiber architectures and requires high-temperature processing. Since there are uncertainties associated with each of these, the observed behavior of composite materials shows scatter. Evaluating the effect of each of these variables on the observed scatter in composite properties solely by teSting is cost and time prohibitive. One alternative is to evaluate these effects by computational simulation. The authors have developed probabilistic composite micromechanics techniques by combining woven composite micromechanics and Fast Probability Integration (FPI) techniques to address these issues. In this paper these techniques will be described and demonstrated through selected examples. Results in the form of cumulative distribution functions (CDF) of the composite properties of a MI (melt-infiltrated) SiC/SiC (silicon carbide fiber in a silicon carbide matrix) Composite will be presented. A CDF is a relationship defined by the value of the property (the response variable) with respect to the cumulative probability of occurrence. Furthermore, input variables causing scatter are identified and ranked based upon their sensitivity magnitude. Sensitivity information is very valuable in quality control. How these results can be utilized to develop design allowables so that these materials may be used by structural analysts/designers will also be discussed.

Mital, Subodh K.↗