Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “thrust”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,423 records · Page 79

Centaur engine gimbal friction characteristics under simulated thrust load

An investigation was performed to determine the friction characteristics of the engine gimbal system of the Centaur upper stage rocket. Because the Centaur requires low-gain autopilots in order to meet all stability requirements for some configurations, control performance (response to transients and limit-cycle amplitudes) depends highly on these friction characteristics. Forces required to rotate the Centaur engine gimbal system were measured under a simulated thrust load of 66,723 N (15,000 lb) and in an altitude/thermal environment. A series of tests was performed at three test conditions; ambient temperature and pressure, ambient temperature and vacuum, and cryogenic temperature and vacuum. Gimbal rotation was controlled, and tests were performed in which rotation amplitude and frequency were varied by using triangular and sinusoidal waveforms. Test data revealed an elastic characteristic of the gimbal, independent of the input signal, which was evident prior to true gimbal sliding. The torque required to initiate gimbal sliding was found to decrease when both pressure and temperature decreased. Results from the low amplitude and low frequency data are currently being used in mathematically modeling the gimbal friction characteristics for Centaur autopilot performance studies.

Askew, J. W.↗

Thrust imbalance of solid rocket motor pairs on Space Shuttle flights

This analysis extends the investigation presented at the 17th Joint Propulsion Conference in 1981 to include fifteen sets of Space Shuttle flight data. The previous report dealt only with static test data and the first flight pair. The objective is to compare the authors' previous theoretical analysis of thrust imbalance with actual Space Shuttle performance. The theoretical prediction method, which involves a Monte Carlo technique, is reviewed briefly as are salient features of the flight instrumentation system and the statistical analysis. A scheme for smoothing flight data is discussed. The effects of changes in design parameters are discussed with special emphasis on the filament wound motor case being developed to replace the steel case. Good agreement between the predictions and the flight data is demonstrated.

Foster, W. A., Jr.↗

Liquid oxygen cooling of high pressure LOX/hydrocarbon rocket thrust chambers

An experimental program using liquid oxygen (LOX) and RP-1 as the propellants and supercritical LOX as the coolant was conducted at 4.14, 8.27, and 13.79 MN/sq m (600, 1200, and 2000 psia) chamber pressure. The objectives of this program were to evaluate the cooling characteristics of LOX with the LOX/RP-1 propellants, the buildup of the soot on the hot-gas-side chamber wall, and the effect of an internal LOX leak on the structural integrity of the combustor. Five thrust chambers with throat diameters of 6.6 cm (2.5 in.) were tested successfully. The first three were tested at 4.14 MN/sq m (600 psia) chamber pressure over a mixture ratio range of 2.25 to 2.92. One of these three was tested for over 22 cyclic tests after the first through crack from the coolant channel to the combustion zone was observed with no apparent metal burning or distress. The fourth chamber was tested at 8.27 MN/sq m (1200 psia) chamber pressure over a mixture range of 1.93 to 2.98. The fourth and fifth chambers were tested at 13.79 MN/sq m (2000 psia) chamber pressure over a mixture ratio range of 1.79 to 2.68.

Price, H. G.↗

STOL landing thrust: Reverser jet flowfields

Analysis tools and modeling concepts for jet flow fields encountered upon use of thrust reversers for high performance military aircraft are described. A semi-empirical model of the reverser ground wall jet interaction with the uniform cross flow due to aircraft forward velocity is described. This ground interaction model is used to demonstrate exhaust gas ingestion conditions. The effects of control of exhaust jet vector angle, lateral splay, and moving versus fixed ground simulation are discussed. The Adler/Baron jet-in-cross flow model is used in conjunction with three dimensional panel methods to investigate the upper surface jet induced flow field.

Kotansky, D. R.↗

Static internal performance of a two-dimensional convergent-divergent nozzle with thrust vectoring

A parametric investigation of the static internal performance of multifunction two-dimensional convergent-divergent nozzles has been made in the static test facility of the Langley 16-Foot Transonic Tunnel. All nozzles had a constant throat area and aspect ratio. The effects of upper and lower flap angles, divergent flap length, throat approach angle, sidewall containment, and throat geometry were determined. All nozzles were tested at a thrust vector angle that varied from 5.60 tp 23.00 deg. The nozzle pressure ratio was varied up to 10 for all configurations.

Bare, E. Ann↗

A computational study of thrust augmenting ejectors based on a viscous-inviscid approach

A viscous-inviscid interaction technique is advocated as both an efficient and accurate means of predicting the performance of two-dimensional thrust augmenting ejectors. The flow field is subdivided into a viscous region that contains the turbulent jet and an inviscid region that contains the ambient fluid drawn into the device. The inviscid region is computed with a higher-order panel method, while an integral method is used for the description of the viscous part. The strong viscous-inviscid interaction present within the ejector is simulated in an iterative process where the two regions influence each other en route to a converged solution. The model is applied to a variety of parametric and optimization studies involving ejectors having either one or two primary jets. The effects of nozzle placement, inlet and diffuser shape, free stream speed, and ejector length are investigated. The inlet shape for single jet ejectors is optimized for various free stream speeds and Reynolds numbers. Optimal nozzle tilt and location are identified for various dual-ejector configurations.

Lund, Thomas S.↗

Scale model test results of a thrust reverser concept for advanced multi-functional exhaust systems

An evaluation is made of scale model test results for a 'block-and-turn' thrust reverser design consisting of an internal flow blocker, internal doors, two ports located on the top and bottom of the exhaust duct, cascade-turning vanes located at the port exit to turn the flow, and external doors which guide the exhaust flow. Numerous geometric variations were incorporated in order to obtain parametric aerodynamic design criteria. The baseline reverser configuration exceeded predicted levels of performance. Skewed vane cascade concepts can be as effective in turning the flow as the baseline vane concept.

Kuchar, A. P.↗

Static investigation of post-exit vanes for multiaxis thrust vectoring

Transonic wind tunnel tests are conducted to determine the flow-turning capabilities and nozzle internal performance of axisymmetric and nonaxisymmetric nozzles employing postexit vanes for multiaxis thrust-vectoring. The geometric parameters investigated for the axisymmetric nozzle installation were number of vanes, vane curvature, vane location relative to nozzle exit, and vane deflection angle; for the nonaxisymmetric cases, the parameters were vane planform and curvature, nozzle type, and nozzle exit aspect ratio. Nozzle pressure ratio was varied from 1.5 to 6.0, using high pressure air.

Berrier, Bobby L.↗

Comparison of theoretical and experimental thrust performance of a 1030:1 area ratio rocket nozzle at a chamber pressure of 2413 kN/sq m (350 psia)

The Joint Army, Navy, NASA, Air Force (JANNAF) rocket-engine performance-prediction procedure is based on the use of various reference computer programs. One of the reference programs for nozzle analysis is the Two-Dimensional Kinetics (TDK) Program. The purpose of this report is to calibrate the JANNAF procedure that has been incorporated into the December 1984 version of the TDK program for the high-area-ratio rocket-engine regime. The calibration was accomplished by modeling the performance of a 1030:1 rocket nozzle tested at NASA Lewis. A detailed description of the test conditions and TDK input parameters is given. The reuslts indicate that the computer code predicts delivered vacuum specific impulse to within 0.12 to 1.9 percent of the experimental data. Vacuum thrust coefficient predictions were within + or - 1.3 percent of experimental results. Predictions of wall static pressure were within approximately + or - 5 percent of the measured values.

Smith, Tamara A.↗

Orbital transfer vehicle 3000 LBF thrust chamber assembly hot fire test program

The Aerojet Orbital Transfer Vehicle (OTV) Thrust Chamber Assembly (TCA) concept consists of a hydrogen cooled chamber, and annular injector, and an oxygen cooled centerbody. The hot fire testing of a heat sink version of the chamber with only the throat section using hydrogen cooling is documented. Hydraulic performance of the injector and cooled throat were verified by water flow testing prior to TCA assembly. The cooled throat was proof tested to 3000 psia to verify the integrity of the codeposited EF nickel-cobalt closeout. The first set of hot fire tests were conducted with a heat sink throat to obtain heat flux information. After demonstration of acceptable heat fluxes, the heat sink throat was replaced with the LH2 cooled throat section. Fourteen tests were conducted with a heat sink chamber and throat at chamber pressures of 85 to 359 psia. The injector face was modified at this time to add more face coolant flow. Ten tests were then conducted at chamber pressures of 197 to 620 psia. Actual heat fluxes at the higher chamber pressure range were 23 percent higher than the average of 10 Btu/in 2 predicted.

Schneider, Judy↗

Evaluation and application of VSAERO to a nonaxisymmetric afterbody with thrust vectoring

The incorporation of multifunction nozzles into fighter aircraft can enhance fighter maneuverability and performance. Development of computational methods will be vital for determining efficient methods of aerodynamic integration of these nozzles. This paper will discuss the utilization of a current technology subsonic panel method (VSAERO) for predicting the flow about a nonaxisymmetric nozzle afterbody with and without a thrust vectoring concept. Two modelings for the vectored exhaust are presented. Highly favorable comparisons were obtained with a rudimentary modeling of the vectored exhaust.

Carlson, John R.↗

Impact of bypass ratio on thrust-to-weight for V/STOL

Issues involved in the selection of a V/STOL propulsion system are discussed. The effect of bypass ratio on thrust-to-weight, fuel flow, and hover efficiency is investigated for the cases of four representative tilt propulsion system aircraft. The effect of fan pressure ratio on engine selection is shown to be very mission dependent. It is noted that the FAA requires reserves based on fixed wing or helicopter operations, neither of which is found to be entirely appropriate for STOVL aircraft.

Wilson, Samuel↗

Three dimensional thermal analysis of rocket thrust chambers

A numerical model for the three-dimensional thermal analysis of rocket thrust chambers and nozzles has been developed. The input to the model consists of the composition of the fuel/oxidant mixture and flow rates, chamber pressure, coolant entrance temperature and pressure, dimensions of the engine, materials and the number of nodes in different parts of the engine. The model allows for temperature variation in three dimensions: axial, radial and circumferential directions and by implementing an iterative scheme, it provides nodal temperature distribution, rates of heat transfer, hot gas and coolant thermal and transport properties.

Naraghi, M. H. N.↗

A static investigation of a simultaneous pitch and yaw thrust vectoring 2-D C-D nozzle

An investigation has been conducted in the static test facility of the Langley 16-Foot Transonic Tunnel to determine the internal performance and flow-turning capability of a two-dimensional convergent-divergent nozzle. Thrust vectoring in the pitch plane was provided by rotation of the divergent flaps. The exhaust stream was turned in the yaw direction by deflection of yaw flaps hinged at the end of the nozzle sidewalls. The yaw flap hinge location was varied along the divergent region of the nozzle at four locations including the exit plane and the throat plane. The three hinge locations upstream of the nozzle exit plane required the downstream corners of both upper and lower divergent flaps to be cut off to eliminate interference when the yaw flaps were deflected. Three different lengths of yaw flaps were tested at several angles of deflection. The nozzle simulated a dry power setting with an expansion ratio typical of subsonic cruise and was tested at nozzle pressure ratios from 2.0 to 7.0.

Taylor, John G.↗

Eigenstructure assignment for a thrust-vectored high angle-of-attack aircraft

Eigenstructure assignment is utilized to design flight control laws for a thrust-vectored aircraft at several different angles of attack. An interesting characteristic of the aircraft model is that the control distribution matrix is rank-deficient. Also, the effectiveness of the control inputs varies with the angle of attack. A pseudocontrol strategy is used to reduce the control space to two dimensions. After the eigenstructure assignment design is complete, the controller is mapped back to the original five-dimensional control space. The designs are shown to exhibit acceptable multivariable stability margins at the aircraft inputs.

Sobel, Kenneth M.↗

A control-volume method for analysis of unsteady thrust augmenting ejector flows

A method for predicting transient thrust augmenting ejector characteristics is presented. The analysis blends classic self-similar turbulent jet descriptions with a control volume mixing region discretization to solicit transient effects in a new way. Division of the ejector into an inlet, diffuser, and mixing region corresponds with the assumption of viscous-dominated phenomenon in the latter. Inlet and diffuser analyses are simplified by a quasi-steady analysis, justified by the assumptions that pressure is the forcing function in those regions. Details of the theoretical foundation, the solution algorithm, and sample calculations are given.

Drummond, Colin K.↗

CISLUNAR program manual: A low-thrust trajectory determination model

CISLUNAR is a stand-alone computer program designed to generate the trajectory of a low-thrust spacecraft travelling in Earth-Moon space. The program allows the creation of functional trajectories dependent on the supplied spacecraft characteristics. The trajectory generation is a user interactive process. The original intent was for the program user to modify the necessary control values until a staisfactory trajectory has been created.

Source record↗