SEARCH · Engineering Papers
Results for “smoothing”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Investigation of Oxidation Mechanisms in HfS 2 and ZrS 2 via In Situ Electron Microscopy
Transition metal dichalcogenides (TMD) combine semiconducting properties with stability and are therefore widely studied for future microelectronic devices. However, applications require integration with a suitable dielectric at a planar, defect-free interface. For Hf- and Zr-based TMDs, the good dielectric properties of hafnia and zirconia imply that direct oxidation is a promising strategy, provided that a high-quality interface and suitable oxide morphology can be formed. Here, in this study, we investigate HfS 2 and ZrS 2 oxidation, aiming to understand pathways toward planar oxide layer formation and the mechanisms that determine the characteristics of the semiconductor/dielectric interface. We use conventional and environmental transmission electron microscopy to reveal changes in morphology and composition of the TMDs under different gaseous environments. We show that oxidation at ambient conditions causes compositional heterogeneities, with local replacement of S by O in both materials. Thermal oxidation causes desulfurization and formation of a smooth but defective oxide layer. In contrast, plasma oxidation appears the best-suited to forming a controlled TMD/dielectric interface with a smooth oxide layer and without major defects. These results provide insight into the opportunities available from HfS 2 and ZrS 2 through oxidation and suggest a materials processing strategy for electronic device fabrication.
Cold Seeded Epitaxy and Flexomagnetism in GdAuGe Membranes Exfoliated From Graphene/Ge(111)
Remote and van der Waals epitaxy are promising approaches for synthesizing single crystalline membranes for flexible electronics and discovery of new properties via extreme strain; however, a fundamental challenge is that most materials do not wet the graphene surface. We develop a cold seed approach for synthesizing smooth intermetallic films on graphene that can be exfoliated to form few nanometer thick single crystalline membranes. Our seeded GdAuGe films have narrow X-ray rocking curve widths of 9–24 arc seconds, which is 2 orders of magnitude lower than their counterparts grown by typical high temperature methods, and have atomically sharp interfaces observed by transmission electron microscopy. Upon exfoliation and rippling, strain gradients in GdAuGe membranes induce an antiferromagnetic to ferri/ferromagnetic transition. Finally, our smooth, ultrathin membranes provide a clean platform for discovering new flexomagnetic effects in quantum materials.
Thermal Transport in Silicon Nanowires at High Temperature up to 700 K
Thermal transport in silicon nanowires has captured the attention of scientists for understanding phonon transport at the nanoscale, and the thermoelectric figure-of-merit (ZT) reported in rough nanowires has inspired engineers to develop cost-effective waste heat recovery systems. Thermoelectric generators composed of silicon target high-temperature applications due to improved efficiency beyond 550 K. However, there have been no studies of thermal transport in silicon nanowires beyond room temperature. High-temperature measurements also enable studies of unanswered questions regarding the impact of surface boundaries and varying mode contributions as the highest vibrational modes are activated (Debye temperature of silicon is 645 K). Here, we develop a technique to investigate thermal transport in nanowires up to 700 K. Furthermore, our thermal conductivity measurements on smooth silicon nanowires show the classical diameter dependence from 40 to 120 nm. In conjunction with Boltzmann transport equation, we also probe an increasing contribution of high-frequency phonons (optical phonons) in smooth silicon nanowires as the diameter decreases and the temperature increases. Thermal conductivity of rough silicon nanowires is significantly reduced throughout the temperature range, demonstrating a potential for efficient thermoelectric generation (e.g., ZT = 1 at 700 K).
Homoepitaxy of Crystalline Rubrene Thin Films
The smooth surface of crystalline rubrene films formed through an abrupt heating process provides a valuable platform to study organic homoepitaxy. By varying growth rate and substrate temperature, we are able to manipulate the onset of a transition from layer-by-layer to island growth modes, while the crystalline thin films maintain a remarkably smooth surface (less than 2.3 nm root-mean-square roughness) even with thick (80 nm) adlayers. We also uncover evidence of point and line defect formation in these films, indicating that homoepitaxy under our conditions is not at equilibrium or strain-free. Point defects that are resolved as screw dislocations can be eliminated under closer-to-equilibrium conditions, whereas we are not able to eliminate the formation of line defects within our experimental constraints at adlayer thicknesses above ~25 nm. We are, however, able to eliminate these line defects by growing on a bulk single crystal of rubrene, indicating that the line defects are a result of strain built into the thin film template. We utilize electron backscatter diffraction, which is a first for organics, to investigate the origin of these line defects and find that they preferentially occur parallel to the (002) plane, which is in agreement with expectations based on calculated surface energies of various rubrene crystal facets. By combining the benefits of crystallinity, low surface roughness, and thickness-tunability, this system provides an important study of attributes valuable to high-performance organic electronic devices.
Effect of Interfacial Alloying versus “Volume Scaling” on Auger Recombination in Compositionally Graded Semiconductor Quantum Dots
Auger recombination is a nonradiative three-particle process wherein the electron–hole recombination energy dissipates as a kinetic energy of a third carrier. Auger decay is enhanced in quantum-dot (QD) forms of semiconductor materials compared to their bulk counterparts. Because this process is detrimental to many prospective applications of the QDs, the development of effective approaches for suppressing Auger recombination has been an important goal in the QD field. One such approach involves “smoothing” of the confinement potential, which suppresses the intraband transition involved in the dissipation of the electron–hole recombination energy. Here, the present study evaluates the effect of increasing “smoothness” of the confinement potential on Auger decay employing a series of CdSe/CdS-based QDs wherein the core and the shell are separated by an intermediate layer of a CdSe x S 1–x alloy comprised of 1–5 sublayers with a radially tuned composition. As inferred from single-dot measurements, use of the five-step grading scheme allows for strong suppression of Auger decay for both biexcitons and charged excitons. Further, due to nearly identical emissivities of neutral and charged excitons, these QDs exhibit an interesting phenomenon of lifetime blinking for which random fluctuations of a photoluminescence lifetime occur for a nearly constant emission intensity.
Kinetic Growth Regimes of Hydrothermally Synthesized Potassium Tantalate Nanoparticles
A general mathematical kinetic growth model is proposed on the basis of observed growth regimes of hydrothermally synthesized KTaO 3 nanoparticles from electron microscopy studies on the surface morphology and surface chemistry. Secondary electron imaging demonstrated that there are two dominant growth mechanisms: terrace nucleation, where the surfaces are rough, and terrace growth, where surfaces are smooth. In the proposed model based upon standard step-flow growth, the rates of both mechanisms are established to be dependent on the chemical potential change of the growth environment-terrace nucleation dominates with larger negative chemical potential, and terrace growth dominates with smaller negative chemical potential. This analysis illustrates the importance of ending a synthesis in a regime of low negative chemical potential in order to achieve smooth well-faceted nanoparticles.
Magnetic Texture in Insulating Single Crystal High Entropy Oxide Spinel Films
Magnetic insulators are important materials for a range of next-generation memory and spintronic applications. Structural constraints in this class of devices generally require a clean heterointerface that allows effective magnetic coupling between the insulating layer and the conducting layer. However, there are relatively few examples of magnetic insulators that can be synthesized with surface qualities that would allow these smooth interfaces and precisely tuned interfacial magnetic exchange coupling, which might be applicable at room temperature. In this work, we demonstrate an example of how the configurational complexity in the magnetic insulator layer can be used to realize these properties. The entropy-assisted synthesis is used to create single-crystal (Mg 0.2 Ni 0.2 Fe 0.2 Co 0.2 Cu 0.2 )Fe 2 O 4 films on substrates spanning a range of strain states. These films show smooth surfaces, high resistivity, and strong magnetic responses at room temperature. Furthermore, local and global magnetic measurements further demonstrate how strain can be used to manipulate the magnetic texture and anisotropy. These findings provide insight into how precise magnetic responses can be designed using compositionally complex materials that may find application in next-generation magnetic devices.
Solvent-Free Melt-Processed Cathode Mitigates Li Anode Instability in Polymer-Based Solid-State Batteries
Solvent-free manufacturing of battery components is a promising alternative to traditional slurry processing for reducing the cost and environmental impact. In this work, we used twin-screw melt extrusion to fabricate a polymer-based high voltage composite cathode. The melt-processed cathode is dense (near zero porosity) and thick (65 μm) and has high active material loading (80 wt %). The active particles are distributed uniformly throughout the melt-processed cathode, unlike the traditional slurry-cast cathode, which exhibits inhomogeneous particle distribution. In the melt-processed cathode, polymer and carbon form separate phases, whereas in the slurry-cast cathode they blend into a single phase. Due to these structural differences, the melt-processed cathode shows smooth charge–discharge profiles, while the slurry-cast cathode shows noisy charging and soft-shorting behavior. In conclusion, this work highlights that twin-screw extrusion as a scalable, solvent-free manufacturing method is advantageous in producing uniform cathodes, which mitigates anode instability.
Roll-to-Roll Printing of Perovskite Solar Cells
High efficiency combined with transformative roll-to-roll (R2R) printability makes metal halide perovskite-based solar cells the most promising solar technology to address the terawatt challenge of the future energy demand. However, translation from lab-scale deposition solution processing techniques to large-scale R2R methods has typically led to reduced photovoltaic performance. Here, we demonstrate large-scale, highly crystalline, uniaxially oriented, smooth perovskite films printed at room temperature and in the ambient environment. Confirmed with high speed in situ X-ray diffraction measurements, the perovskite films reach 98% of relative crystallinity at room temperature and display high texture within 1 s of the coating. We demonstrate an all-blade-coated metal halide perovskite cell with power conversion efficiency (PCE) up to 19.6%, a slot-die coated cell with a PCE of 17.3%, and a partially R2R slot-die coated flexible glass-based cell efficiency of 14.1%. As a result the developed printing method can be applied to diverse perovskite compositions, enabling a variety of bandgaps to pave the way for the future R2R printing of highly efficient perovskite–perovskite tandem cells.
Machine Learning-Assisted Recovery of Delicate Kinetic Information from Transient Reactor Experiments
Identifying active sites and their roles in chemical reaction steps remains a vital challenge in heterogeneous catalysis. Transient experiments offer a unique way to probe active sites and distinguish subtle kinetic features. Although physics-based analysis methods may be well-developed, they can be highly susceptible to experimental noise, and smoothing methods may erase or even distort important features; a smooth curve is not always the best curve. We demonstrate a new workflow for the direct interpretation of intrinsic kinetic information from exit flux curves measured in transient reactor experiments. This workflow contains three artificial neural networks (ANNs), including a noise reducer, a concentration predictor, and a rate predictor to analyze experimental data, followed by the virtual TAP (VTAP) physics-based reactor model and density functional theory (DFT) calculations of adsorption energies on specific sites. We use this workflow to analyze the data from experiments titrating Pt/Al 2 O 3 and Pt/SiO 2 catalysts with carbon monoxide (CO) in the temporal analysis of products (TAP) reactor. Our workflow separates the time-evolving chemical reaction and mass transfer information contained in the TAP pulse response. The existence of strong- and weak-binding sites on the Pt/Al 2 O 3 catalyst is observed in the catalyst titration experiment in the transient reactor. The structures of the strong- and weak-binding sites are then identified by using DFT calculations. We find that the Pt/SiO 2 catalyst has only strong-binding sites, which aligns with the inactive support effect of SiO 2 . We demonstrate how machine learning methods provide unique insights with high-resolution data analysis that cannot be achieved by using state-of-the-art physics-based methods.
Superposition Principle in Auger Recombination of Charged and Neutral Multicarrier States in Semiconductor Quantum Dots
Application of colloidal semiconductor quantum dots (QDs) in optical and optoelectronic devices is often complicated by unintentional generation of extra charges, which opens fast nonradiative Auger recombination pathways whereby the recombination energy of an exciton is quickly transferred to the extra carrier(s) and ultimately dissipated as heat. Previous studies of Auger recombination have primarily focused on neutral and, more recently, negatively charged multicarrier states. Auger dynamics of positively charged species remains more poorly explored due to difficulties in creating, stabilizing, and detecting excess holes in the QDs. Here we apply photochemical doping to prepare both negatively and positively charged CdSe/CdS QDs with two distinct core/shell interfacial profiles (“sharp” versus “smooth”). Using neutral and charged QD samples we evaluate Auger lifetimes of biexcitons, negative and positive trions (an exciton with an extra electron or a hole, respectively), and multiply negatively charged excitons. Using these measurements, we demonstrate that Auger decay of both neutral and charged multicarrier states can be presented as a superposition of independent elementary three-particle Auger events. As one of the manifestations of the superposition principle, we observe that the biexciton Auger decay rate can be presented as a sum of the Auger rates for independent negative and positive trion pathways. Furthermore, by comparing the measurements on the QDs with the “sharp” versus “smooth” interfaces, we also find that while affecting the absolute values of Auger lifetimes, manipulation of the shape of the confinement potential does not lead to violation of the superposition principle, which still allows us to accurately predict the biexciton Auger lifetimes based on the measured negative and positive trion dynamics. Our findings indicate considerable robustness of the superposition principle as applied to Auger decay of charged and neutral multicarrier states, suggesting its generality to quantum-confined nanocrystals of arbitrary compositions and complexities.
Understanding Multiscale Structural Changes During Dilute Acid Pretreatment of Switchgrass and Poplar
Biofuels produced from lignocellulosic biomass hold great promise as a renewable alternative energy and fuel source. To realize a cost and energy efficient approach, a fundamental understanding of the deconstruction process is critically necessary to reduce biomass recalcitrance. Here, the structural and morphological changes over multiple scales (5–6000 Å) in herbaceous (switchgrass) and woody (hybrid poplar) biomass during dilute sulfuric acid pretreatment were explored using neutron scattering and X-ray diffraction. Switchgrass undergoes a larger increase (20–84 Å) in the average diameter of the crystalline core of the elementary cellulose fibril than hybrid poplar (19–50 Å). Switchgrass initially forms lignin aggregates with an average size of 90 Å that coalesce to 200 Å, which is double that observed for hybrid poplar, 55–130 Å. Switchgrass shows a smooth-to-rough transition in the cell wall surface morphology unlike the diffuse-to-smooth transition of hybrid poplar. Yet, switchgrass and hybrid poplar pretreated under the same experimental conditions result in pretreated switchgrass producing higher glucose yields (~76 wt %) than pretreated hybrid poplar (~60 wt %). This observation shows that other aspects like cellulose allomorph transitions, cellulose accessibility, cellular biopolymer spatial distribution, and enzyme–substrate interactions may be more critical in governing the enzymatic hydrolysis efficiency.
Nematic director reorientation at solid and liquid interfaces under flow: SAXS studies in a microfluidic device
In this work we investigate the interplay between flow and boundary condition effects on the orientation field of a thermotropic nematic liquid crystal under flow and confinement in a microfluidic device. Two types of experiments were performed using synchrotron small-angle X-ray-scattering (SAXS). In the first, a nematic liquid crystal flows through a square-channel cross section at varying flow rates, while the nematic director orientation projected onto the velocity/velocity gradient plane is measured using a 2D detector. At moderate-to-high flow rates, the nematic director is predominantly aligned in the flow direction, but with a small tilt angle of ~±11° in the velocity gradient direction. The director tilt angle is constant throughout most of the channel width but switches sign when crossing the center of the channel, in agreement with the Ericksen–Leslie–Parodi (ELP) theory. At low flow rates, boundary conditions begin to dominate, and a flow profile resembling the escaped radial director configuration is observed, where the director is seen to vary more smoothly from the edges (with homeotropic alignment) to the center of the channel. In the second experiment, hydrodynamic focusing is employed to confine the nematic phase into a sheet of liquid sandwiched between two layers of Triton X-100 aqueous solutions. The average nematic director orientation shifts to some extent from the flow direction toward the liquid boundaries, although it remains unclear if one tilt angle is dominant through most of the nematic sheet (with abrupt jumps near the boundaries) or if the tilt angle varies smoothly between two extreme values (~90 and 0°). Lastly, the technique presented here could be applied to perform high-throughput measurements for assessing the influence of different surfactants on the orientation of nematic phases and may lead to further improvements in areas such as boundary lubrication and clarifying the nature of defect structures in LC displays.
Crust and Upper Mantle Structure Beneath the Eastern United States
Abstract The Eastern United States (EUS) has a complex geological history and hosts several seismic active regions. We investigate the subsurface structure beneath the broader EUS. To produce reliable images of the subsurface, we simultaneously invert smoothed P‐wave receiver functions, Rayleigh‐wave phase and group velocity measurements, and Bouguer gravity observations for the 3D shear‐wave speed. Using surface‐wave observations (3–250 s) and spatially smoothed receiver functions, our velocity models are robust, reliable, and rich in detail. The shear‐wave velocity models fit all three types of observations well. The resulting velocity model for the eastern U.S. shows thinner crust beneath New England, the east coast, and the Mississippi Embayment (ME). A relatively thicker crust was found beneath the stable North America craton. A relatively slower upper mantle was imaged beneath New England, the east coast, and western ME. A comparison of crust thickness derived from our model against four recent published models shows first‐order consistency. A relatively small upper mantle low‐speed region correlates with a published P‐wave analysis that has associated the anomaly with a 75 Ma kimberlite volcanic site in Kentucky. We also explored the relationship between the subsurface structure and seismicity in the eastern U.S. We found that earthquakes often locate near regions with seismic velocity variations, but not universally. Not all regions of significant subsurface wave speed changes are loci of seismicity. A weak correlation between upper mantle shear velocity and earthquake focal mechanism has been observed.
Spontaneous formation of nanoparticles on electrospun nanofibres
We report the spontaneous formation of nanoparticles on smooth nanofibres in a single-step electrospinning process, as an inexpensive and scalable method for producing high-surface-area composites. Layers of nanofibres, containing the proton conducting electrolyte, caesium dihydrogen phosphate, are deposited uniformly over large area substrates from clear solutions of the electrolyte mixed with polymers. Under certain conditions, the normally smooth nanofibres develop caesium dihydrogen phosphate nanoparticles in large numbers on their external surface. The nanoparticles appear to originate from the electrolyte within the fibres, which is transported to the outer surface after the fibres are deposited, as evidenced by cross-sectional imaging of the electrospun fibres. The presence of nanoparticles on the fibre surface yields composites with increased surface area of exposed electrolyte, which ultimately enhances electrocatalytic performance. Indeed, solid acid fuel cells fabricated with electrodes from processed nanofibre-nanoparticle composites, produced higher cell voltage as compared to fuel cells fabricated with state-of-the-art electrodes.
Mild-to-wild plastic transition is governed by athermal screw dislocation slip in bcc Nb
Plastic deformation in crystals is mediated by the motion of line defects known as dislocations. For decades, dislocation activity has been treated as a homogeneous, smooth continuous process. However, it is now recognized that plasticity can be determined by long-range correlated and intermittent collective dislocation processes, known as avalanches. Here we demonstrate in body-centered cubic Nb how the long-range and scale-free dynamics at room temperature are progressively quenched out with decreasing temperature, eventually revealing intermittency with a characteristic length scale that approaches the Burgers vector itself. Plasticity is shown to be bimodal across the studied temperature regime, with conventional thermally-activated smooth plastic flow (‘mild’) coexisting with sporadic bursts (‘wild’) controlled by athermal screw dislocation activity, thereby violating the classical notion of temperature-dependent screw dislocation motion at low temperatures. An abrupt increase of the athermal avalanche component is identified at the critical temperature of the material. Our results indicate that plasticity at any scale can be understood in terms of the coexistence of these mild and wild modes of deformation, which could help design better alloys by suppressing one of the two modes in desired temperature windows.
Electrochemical properties and structural evolution of O3-type layered sodium mixed transition metal oxides with trivalent nickel
The electrochemical properties of NaNi 0.5 Co 0.5 O 2 and NaNi 0.5 Fe 0.5 O 2 and their structural transitions as a function of Na extraction associated with redox reactions are investigated. Synthesized in the O3-type layered structure, both materials show reasonable electrochemical activities at room temperature, delivering approximately 0.5 Na per formula unit at C/10 discharge. More Na can be reversibly cycled in NaNi 0.5 Co 0.5 O 2 at elevated temperature and/or in an extended voltage window, while NaNi 0.5 Fe 0.5 O 2 shows significant capacity fading at a high voltage cutoff which is likely due to Fe 4+ migration. In situ X-ray diffraction shows that the structural changes in the two materials upon desodiation are very different. NaNi 0.5 Co 0.5 O 2 goes through many different two-phase reactions including three different O3-type and three different P3-type structures during cycling, producing a voltage profile with multiple plateau-like features. In contrast, NaNi 0.5 Fe 0.5 O 2 has a smooth voltage profile and shows the typical O3–P3 phase transition without lattice distortion seen in other materials. Finally, this different structural evolution upon desodiation and re-sodiation can be explained by the electronic structure of the mixed transition metals and how it perturbs the ordering between Na ions differently.