Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “generative diffusion”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,423 records · Page 79

Ionization and chemiluminescence during the progressive aeration of methane flames

Saturation currents and chemiluminescence, especially at the CH{sup *} and C{sub 2}{sup *} wavelengths, are measured for a range of small, laminar methane flames during progressive addition of air, with the principal objective of distinguishing between pure diffusion flames, premixed flames of compositions falling between the upper and lower flammability limits, and the broad range of aerated flames lying in between these regimes. Flame areas defined by the loci of maximum luminosity and by schlieren contours were recorded, so that saturation current densities, CH{sup *} and C{sub 2}{sup *} emission per unit flame area, as well as burning velocities could be deduced. For admixtures of less than 70 vol.%, air appears to act, surprisingly, as an inert diluent as regards saturation currents, so that saturation currents are essentially proportional to fuel flow alone. Much the same applies to chemiluminescence. However, schlieren contours, which were recorded both to provide a basis for burning velocity measurements and to explore density changes in the reactants, indicated the presence of a burner - stabilised propagating reaction zone ahead of the luminous flame surface starting at around 50 vol.% and possibly even at lower air admixtures. This evidence of a steep change in refractive index is indicative of a premixed reaction zone involving the added oxygen, which however generates no chemi-ionization and emits no light. Even photographing the flame by radiation emitted at the CH{sup *} and C{sub 2}{sup *} wavelengths shows no sign of its existence. Its burning velocity is about 10 cm/s, when stabilized by the surrounding diffusion flame. The most plausible rationale for these observations is the formation of syngas by the partial oxidation of methane. The subsequent burning of CO and H{sub 2} is known to occur without chemi-ionization or appreciable light emission. (author)

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Metagenomic Evaluation of Bacterial and Fungal Assemblages Enriched within Diffusion Chambers and Microbial Traps Containing Uraniferous Soils

Despite significant technological advancements in the field of microbial ecology, cultivation and subsequent isolation of the vast majority of environmental microorganisms continues to pose challenges. Isolation of the environmental microbiomes is prerequisite to better understand a myriad of ecosystem services they provide, such as bioremediation of contaminants. Towards this end, in this culturomics study, we evaluated the colonization of soil bacterial and fungal communities within diffusion chambers (DC) and microbial traps (MT) established using uraniferous soils collected from a historically contaminated soil from Aiken, USA. Microbial assemblages were compared between the DC and MT relative to the native soils using amplicon based metagenomic and bioinformatic analysis. The overall rationale of this study is that DC and MT growth chambers provide the optimum conditions under which desired microbiota, identified in a previous study to serve as the “core” microbiomes, will proliferate, leading to their successful isolation. Specifically, the core microbiomes consisted of assemblages of bacteria (Burkholderia spp.) and fungi (Penicillium spp.), respectively. The findings from this study further supported previous data such that the abundance and diversity of the desired “core” microbiomes significantly increased as a function of enrichments over three consecutive generations of DC and MT, respectively. Metagenomic analysis of the DC/MT generations also revealed that enrichment and stable populations of the desired “core” bacterial and fungal microbiomes develop within the first 20 days of incubation and the practice of subsequent transfers for second and third generations, as is standard in previous studies, may be unnecessary. As a cost and time cutting measure, this study recommends running the DC/MT chambers for only a 20-day time period, as opposed to previous studies, which were run for months. In summation, it was concluded that, using the diffusion chamber-based enrichment techniques, growth of desired microbiota possessing environmentally relevant functions can be achieved in a much shorter time frame than has been previously shown.

Jaswal, Rajneesh (ORCID:0000000217841805)↗

NONLINEAR EVOLUTION OF GLOBAL HYDRODYNAMIC SHALLOW-WATER INSTABILITY IN THE SOLAR TACHOCLINE

We present a fully nonlinear hydrodynamic 'shallow-water' model of the solar tachocline. The model consists of a global spherical shell of differentially rotating fluid, which has a deformable top, thus allowing motions in radial directions along with latitudinal and longitudinal directions. When the system is perturbed, in the course of its nonlinear evolution it can generate unstable low-frequency shallow-water shear modes from the differential rotation, high-frequency gravity waves, and their interactions. Radiative and overshoot tachoclines are characterized in this model by high and low effective gravity values, respectively. Building a semi-implicit spectral scheme containing very low numerical diffusion, we perform nonlinear evolution of shallow-water modes. Our first results show that (1) high-latitude jets or polar spin-up occurs due to nonlinear evolution of unstable hydrodynamic shallow-water disturbances and differential rotation, (2) Reynolds stresses in the disturbances together with changing shell thickness and meridional flow are responsible for the evolution of differential rotation, (3) disturbance energy primarily remains concentrated in the lowest longitudinal wavenumbers, (4) an oscillation in energy between perturbed and unperturbed states occurs due to evolution of these modes in a nearly dissipation-free system, and (5) disturbances are geostrophic, but occasional nonadjustment in geostrophic balance can occur, particularly in the case of high effective gravity, leading to generation of gravity waves. We also find that a linearly stable differential rotation profile remains nonlinearly stable.

79 ASTRONOMY AND ASTROPHYSICS↗

Glancing Angle Deposition in Gas Sensing: Bridging Morphological Innovations and Sensor Performances

Glancing Angle Deposition (GLAD) has emerged as a versatile and powerful nanofabrication technique for developing next-generation gas sensors by enabling precise control over nanostructure geometry, porosity, and material composition. Through dynamic substrate tilting and rotation, GLAD facilitates the fabrication of highly porous, anisotropic nanostructures, such as aligned, tilted, zigzag, helical, and multilayered nanorods, with tunable surface area and diffusion pathways optimized for gas detection. This review provides a comprehensive synthesis of recent advances in GLAD-based gas sensor design, focusing on how structural engineering and material integration converge to enhance sensor performance. Key materials strategies include the construction of heterojunctions and core–shell architectures, controlled doping, and nanoparticle decoration using noble metals or metal oxides to amplify charge transfer, catalytic activity, and redox responsiveness. GLAD-fabricated nanostructures have been effectively deployed across multiple gas sensing modalities, including resistive, capacitive, piezoelectric, and optical platforms, where their high aspect ratios, tailored porosity, and defect-rich surfaces facilitate enhanced gas adsorption kinetics and efficient signal transduction. These devices exhibit high sensitivity and selectivity toward a range of analytes, including NO2, CO, H2S, and volatile organic compounds (VOCs), with detection limits often reaching the parts-per-billion level. Emerging innovations, such as photo-assisted sensing and integration with artificial intelligence for data analysis and pattern recognition, further extend the capabilities of GLAD-based systems for multifunctional, real-time, and adaptive sensing. Finally, current challenges and future research directions are discussed, emphasizing the promise of GLAD as a scalable platform for next-generation gas sensing technologies.

Chemistry↗

An Electro-Assisted Powder Metallurgical Route for the Preparation of Porous Ti and NiTi in Molten CaCl{sub 2}

Molten salts can provide a high-temperature and oxygen-water-free environment, and the electrochemical polarization is able to reduce the oxide scale on the surface of Ti and Ni particles in molten salts and, thereby, enhance the sintering and accelerating atom diffusion between Ti and Ni. Thus, an electro-assisted powder metallurgical (EPM) approach was developed to prepare porous Ti and NiTi from metal powders in molten salts, where the porous pellet cathode made of the mixture of Ni and Ti powders is electrochemically polarized to facilitate the generation of the porous Ti and NiTi at a temperature lower than 1000 °C. The electrolytic product obtained under a cell voltage of 3 V for 12 hours is nearly pure NiTi with a tiny amount of undesired Ni{sub 3}Ti and NiTi{sub 2} phases. Overall, the EPM route could be a straightforward and general way to prepare porous Ti and Ti-alloys for implants and other applications.

36 MATERIALS SCIENCE↗

Kinetic mix mechanisms in shock-driven inertial confinement fusion implosions

Shock-driven implosions of thin-shell capsules, or ''exploding pushers,'' generate low-density, high-temperature plasmas in which hydrodynamic instability growth is negligible and kinetic effects can play an important role. Data from implosions of thin deuterated-plastic shells with hydroequivalent D 3 He gas fills ranging from pure deuterium to pure 3 He [H. G. Rinderknecht et al., Phys. Rev. Lett. 112, 135001 (2014)] were obtained to evaluate non-hydrodynamic fuel-shell mix mechanisms. Simulations of the experiments including reduced ion kinetic models support ion diffusion as an explanation for these data. Several additional kinetic mechanisms are investigated and compared to the data to determine which are important in the experiments. Shock acceleration of shell deuterons is estimated to introduce mix less than or comparable to the amount required to explain the data. Beam-target mechanisms are found to produce yields at most an order of magnitude less than the observations

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Measurement of Passive Uptake Rates for Volatile Organic Compounds on Commercial Thermal Desorption Tubes and the Effect of Ozone on Sampling

Diffusive or passive sampling methods using commercially filled axial-sampling thermal desorption tubes are widely used for measuring volatile organic compounds (VOCs) in air. The passive sampling method provides a robust, cost effective way to measure air quality with time-averaged concentrations spanning up to a week or more. Sampling rates for VOCs can be calculated using tube geometry and Fick’s Law for ideal diffusion behavior or measured experimentally. There is evidence that uptake rates deviate from ideal and may not be constant over time. Therefore, experimentally measured sampling rates are preferred. In this project, a calibration chamber with a continuous stirred tank reactor design and constant VOC source was combined with active sampling to generate a controlled dynamic calibration environment for passive samplers. The chamber air was augmented with a continuous source of 45 VOCs ranging from pentane to diethyl phthalate representing a variety of chemical classes and physiochemical properties. Both passive and active samples were collected on commercially filled Tenax TA thermal desorption tubes over an 11-day period and used to calculate passive sampling rates. A second experiment was designed to determine the impact of ozone on passive sampling by using the calibration chamber to passively load five terpenes on a set of Tenax tubes and then exposing the tubes to different ozone environments with and without ozone scrubbers attached to the tube inlet. During the sampling rate experiment, the measured diffusive uptake was constant for up to seven days for most of the VOCs tested but deviated from linearity for some of the more volatile compounds between seven and eleven days. In the ozone experiment, both exposed and unexposed tubes showed a similar decline in terpene mass over time indicating back diffusion when uncapped tubes were transferred to a clean environment but there was no indication of significant loss by ozone reaction.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

Specific features of light current-voltage characteristics of p-i-n structures based on amorphous silicon in the case of the tunnel-drift mechanism of dark current transport

Current-voltage (I-V) characteristics of p-i-n structures based on amorphous silicon ({alpha}-Si:H) with small hole diffusion lengths (shorter than the thickness of the i-layer of a p-i-n structure) have been experimentally studied with and without illumination. It is shown that forward I-V characteristics of structures of this kind can be described by a dependence inherent in diodes, with a diode ideality factor two-three times the maximum value of 2, theoretically predicted for generation-recombination currents in p-n junctions. The dark current is always substantially lower than the photocurrent in a cell biased with a voltage approximately equal to the opencircuit voltage of the photocell. Dark currents cannot contribute to the I-V characteristic under illumination. The photocurrent decreases with increasing photovoltage at a bias lower than the open-circuit voltage because of a decrease in the collection coefficient and the increasingly important role of back diffusion of electrons into the p-contact, rather than as a result of the dark injection. In the case of biases exceeding the open-circuit voltage, back diffusion becomes the predominant component of the current.

36 MATERIALS SCIENCE↗

A Low-Temperature, Solution-Processable, Cu-Doped Nickel Oxide Hole-Transporting Layer via the Combustion Method for High-Performance Thin-Film Perovskite Solar Cells

The promising photophysical properties of the emerging organometallic halide perovskites, such as intense broadband absorption, high charge carrier mobility, and long charge diffusion length, have enabled the rapid development in solar cells reaching over 20% power conversion effi ciency (PCE) recently. Especially, the low material cost and facile solution processability of perovskites are very attractive as next-generation photovoltaic materials for sustainable energy.

14 SOLAR ENERGY↗

Elucidating the Irreversible Mechanism and Voltage Hysteresis in Conversion Reaction for High-Energy Sodium-Metal Sulfide Batteries

We present that irreversible electrochemical behavior and large voltage hysteresis are commonly observed in battery materials, in particular for materials reacting through conversion reaction, resulting in undesirable round-trip energy loss and low coulombic efficiency. Seeking solutions to these challenges relies on the understanding of the underlying mechanism and physical origins. Here, this study combines in operando 2D transmission X-ray microscopy with X-ray absorption near edge structure, 3D tomography, and galvanostatic intermittent titration techniques to uncover the conversion reaction in sodium–metal sulfide batteries, a promising high-energy battery system. This study shows a high irreversible electrochemistry process predominately occurs at first cycle, which can be largely linked to Na ion trapping during the first desodiation process and large interfacial ion mobility resistance. Subsequently, phase transformation evolution and electrochemical reaction show good reversibility at multiple discharge/charge cycles due to materials' microstructural change and equilibrium. The origin of large hysteresis between discharge and charge is investigated and it can be attributed to multiple factors including ion mobility resistance at the two-phase interface, intrinsic slow sodium ion diffusion kinetics, and irreversibility as well as ohmic voltage drop and overpotential. In conclusion, this study expects that such understandings will help pave the way for engineering design and optimization of materials microstructure for future-generation batteries.

25 ENERGY STORAGE↗

The Role of Kinetic Instabilities and Waves in Collisionless Magnetic Reconnection

Magnetic reconnection converts magnetic field energy into particle energy by breaking and reconnecting magnetic field lines. Magnetic reconnection is a kinetic process that generates a wide variety of kinetic waves via wave-particle interactions. Kinetic waves have been proposed to play an important role in magnetic reconnection in collisionless plasmas by, for example, contributing to anomalous resistivity and diffusion, particle heating, and transfer of energy between different particle populations. These waves range from below the ion cyclotron frequency to above the electron plasma frequency and from ion kinetic scales down to electron Debye length scales. This review aims to describe the progress made in understanding the relationship between magnetic reconnection and kinetic waves. We focus on the waves in different parts of the reconnection region, namely, the diffusion region, separatrices, outflow regions, and jet fronts. Particular emphasis is placed on the recent observations from the Magnetospheric Multiscale (MMS) spacecraft and numerical simulations, which have substantially increased the understanding of the interplay between kinetic waves and reconnection. Some of the ongoing questions related to waves and reconnection are discussed.

79 ASTRONOMY AND ASTROPHYSICS↗

Conserving asphalt resources: Rethinking rejuvenator performance evaluation through peptizing efficiency

Timely rejuvenation and restoration of asphalt are essential conservation practices that help preserve and extend the service life of roads, bridges, driveways, and parking lots. The performance of asphalt rejuvenators is often assessed based on their diffusion rates and softening power, yet these metrics alone fail to capture true rejuvenation potential. Here, this study integrates density functional theory (DFT) modeling with experimental analysis to show that rejuvenation effectiveness is primarily governed by molecular interactions with oxidized asphaltene nanoaggregates. DFT results revealed that amide- and unsaturated-chain compounds, such as hexadecanamide, oleic acid, and 9,17-octadecadienal, act cooperatively to disrupt π–π stacking and exfoliate asphaltene layers, reducing binding strength and enhancing dispersion. Unlike bulky, rigid molecules that remain trapped, these components remain mobile and repeatedly interact with multiple aggregation sites. Experimental validation using rheometry and FTIR confirmed that such molecularly compatible rejuvenators restore the binder flexibility and polydispersity, even when diffusion is relatively slow. Building on this mechanistic foundation, six rejuvenators (A2, A5, A7, A8, A9, and A10) were evaluated using a three-metric performance framework encompassing cracking resistance (Glover–Rowe parameter), UV stability, and surface hydrophobicity. Among the six rejuvenators evaluated, A9 exhibited the highest overall performance, reducing the Glover–Rowe cracking parameter by 85% (from 351 kPa to 53 kPa), demonstrating the greatest resistance to UV-induced aging with a stability index of 4.17 h·kPa⁻¹, and increasing surface hydrophobicity to a contact angle of 103.6°. Its superior performance is primarily attributed to its amide- and unsaturated-chain components, which act cooperatively to disrupt π–π stacking interactions and exfoliate asphaltene layers, thereby promoting molecular deagglomeration and enhancing long-term durability. These results shift the criteria for selecting rejuvenators: effective candidates must pair the electronic capability to unlock aged asphaltenes with sufficient structural stability to resist secondary aging and restore hydrophobicity. Restoring hydrophobicity is critical, as aging reduces the asphalt’s water repellency and increases water diffusion, which in turn accelerates moisture-related damage; consequently, a high-performing rejuvenator must effectively restore the binder’s hydrophobic characteristic. Collectively, these findings provide a framework for the rational design of next-generation of bio-based rejuvenators that enhance pavement longevity and promote long-term sustainability.

Aging↗

Atomic Structure and Dynamics of Self-Limiting Sub-Nanometer Pores in Monolayer WS 2

Here, we reveal a self-limiting mechanism during the formation of a specific type of circular nanopore in monolayer WS 2 that limits its diameter to sub-nm. A single W atom vacancy (triangular nanopore) is transformed into the self-limiting nanopore (SLNP) through the atomic restructuring of S atoms around the area, reducing the number of dangling bonds at the nanopore edge by shifting them further in-plane with W–W bonding instead. Bond rotations in WS 2 help accommodate the electron beam induced atomic loss and ensure the stability of the SLNP. The SLNP shows significant improvement in diameter stability during electron beam irradiation compared to other triangular nanopores in WS 2 that typically continue to expand in diameter during atom loss. The atomic structure of these SLNPs is studied using aberration-corrected scanning transmission electron microscopy with an in situ heating holder, revealing that the SLNPs are mostly formed at a temperature of ~500 °C, which is a balance between thermally activated S vacancy diffusion and sufficient S vacancy density to initiate local atomic reconstruction. At higher temperatures (i.e., 1000 °C), S vacancies quickly migrate away into long line vacancies, resulting in low S vacancy density and rapidly expanding holes generated at the edges of the line vacancies. At room temperature, S vacancy migration is low and vacancy density is very high, which limits atomic reconstruction, and instead many small holes open up. In conclusion, these results provide insights into the factors that lead to uniform sized nanopores in the sub-nm range in transition-metal dichalcogenides.

2D materials↗

The relation of local order to material properties in relaxor ferroelectrics

Correlating electromechanical and dielectric properties with nanometre-scale order is the defining challenge for the development of piezoelectric oxides. Current lead (Pb)-based relaxor ferroelectrics can serve as model systems with which to unravel these correlations, but the nature of the local order and its relation to material properties remains controversial. Here we employ recent advances in diffuse scattering instrumentation to investigate crystals that span the phase diagram of PbMg1/3Nb2/3O3-xPbTiO(3) (PMN-xPT) and identify four forms of local order. From the compositional dependence, we resolve the coupling of each form to the dielectric and electromechanical properties observed. We show that relaxor behaviour does not correlate simply with ferroic diffuse scattering; instead, it results from a competition between local antiferroelectric correlations, seeded by chemical short-range order, and local ferroic order. The ferroic diffuse scattering is strongest where piezoelectricity is maximal and displays previously unrecognized modulations caused by anion displacements. Our observations provide new guidelines for evaluating displacive models and hence the piezoelectric properties of environmentally friendly next-generation materials.

36 MATERIALS SCIENCE↗

Construction of generalized quasilinear diffusion coefficient using neural networks with physical restrictions

The quasilinear diffusion coefficient (D QL ) derived from our machine learning framework shows comparable trends with the ground truth D QL obtained from GENRAY-CQL3D simulations. Additionally, for the strong absorption cases, the radial current drive profiles generated using the D QL from our model exhibit consistent behavior with those obtained from the original simulation. These findings indicate the potential of our surrogate modeling approach with physical restrictions to replicate key wave–plasma interaction characteristics while reducing computational costs. Traditionally, calculating D QL for wave–particle interactions relies on computationally intensive wave simulations coupled with Fokker–Planck solvers. To address this challenge, we developed a machine learning-based surrogate model with physical restrictions derived from cold plasma theory and bounce-averaged damping effects. First, we establish the propagation domain of Lower Hybrid Waves in the (N∥, ρ) space by identifying the accessibility limit and determining the upper and lower bounds of N∥ using the Potential Power Deposition (PPD) method. Subsequently, leveraging a database constructed using Latin hypercube sampling alongside the underlying physical restrictions (e.g. PPD), machine learning methods including U-Net and Recurrent Neural Networks are employed to design a physics-restricted machine learning framework capable of reconstructing D QL .

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Heat transport in the quasi-single-helicity islands of EXTRAP T2R

The heat transport inside the magnetic island generated in a quasi-single-helicity regime of a reversed-field pinch device is studied by using a numerical code that simulates the electron temperature and the soft x-ray emissivity. The heat diffusivity {chi}{sub e} inside the island is determined by matching the simulated signals with the experimental ones. Inside the island, {chi}{sub e} turns out to be from one to two orders of magnitude lower than the diffusivity in the surrounding plasma, where the magnetic field is stochastic. Furthermore, the heat transport properties inside the island are studied in correlation with the plasma current and with the amplitude of the magnetic fluctuations.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Molecular Dynamics Simulations of Displacement Cascades in Single and Polycrystalline Zirconia

Displacement cascades in zirconia have been studied using classical molecular dynamics simulations. Polycrystalline zirconia with nano-meter grains were created using Voronoi polyhedra construction and studied in comparison with single crystalline zirconia. The results show that displacement cascades with similar kinetic energy generated larger number of displaced atoms in polycrystalline than in the single crystal structure. The fraction of atoms with coordination number change was also higher in polycrystalline zirconia that was explained to be due to the diffusion of oxygen and relaxation at grain boundaries.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Analysis of toroidal phasing of resonant magnetic perturbation effects on edge transport in the DIII-D tokamak

Resonant Magnetic Perturbation (RMP) fields produced by external control coils are considered a viable option for the suppression of Edge Localized Modes in present and future tokamaks. In DIII-D, the RMPs are generated by six pairs of I-coils, each spanning 60° in toroidal angle, with the currents flowing in opposite directions in adjacent pairs of I-coils. Reversal of the currents in all I-coils, which produces a 60° toroidal shift in the RMP field configuration, generates uniquely different edge pedestal profiles of the density, temperature, and rotation velocities, implying different effects on the related edge transport phenomena caused by the difference in toroidal phase of the I-coil currents. The diffusive and non-diffusive transport effects of this RMP toroidal phase reversal are analyzed by comparing the ion and electron heat diffusivities, angular momentum transport frequencies, ion diffusion coefficients, and the particle pinch velocities interpreted from the measured profiles for the two phases of the I-coil currents.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗