SEARCH · Engineering Papers

Results for “furnaces”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,423 records · Page 79

All sources NASA NTRS DOE OSTI

NASA NTRS1986

Relation between microstructural heterogeneous surface layer and nitrogen pressure during sintering in Si3N4-Ml2O3 ceramics

The effects of N2 pressure (0.1 to 50 MPa) during sintering on the thickness of the microstructurally heterogeneous layer (MHL) formed near the surface of the compact, transverse-rupture strength, were investigated for Si3N4-(10 to 20) mol % MgO-5.5 mol % Al2O3 ceramics. The sintering temperature and time were 1973 K and 3.6 ks, respectively. The N2 gas was introduced into the furnace at about 1273 K. When the compacts were sintered under a certain N2 pressure, for example, about 20 and 7 MPa for 10 and 15 mol% MgO, respectively, the evolutions of N and Si were suppressed. The thickness of the MHL became very small and at the same time the strength of the surface layer of the compact (which was normally less than that of the inside in the case of 0.1 MPa) became nearly the same value as that of the inside. At higher pressure, the strength of both surface layer and the inside decreased considerably. Some discussion was made on these results.

Hayashi, K.↗

NASA NTRS1984

Characterization of sprays

It is pointed out that most practical power generation and propulsion systems involve the burning of different types of fuel sprays, taking into account aircraft propulsion, industrial furnaces, boilers, gas turbines, and diesel engines. There has been a lack of data which can serve as a basis for spray model development and validation. A major aim of the present investigation is to fill this gap. Experimental apparatus and techniques for studying the characteristics of fuel sprays are discussed, taking into account two-dimensional still photography, cinematography, holography, a laser diffraction particle sizer, and a laser anemometer. The considered instruments were used in a number of experiments, taking into account three different types of fuel spray. Attention is given to liquid fuel sprays, high pressure pulsed diesel sprays, and coal-water slurry sprays.

Chigier, N.↗

NASA NTRS1985

Preparation for microgravity science investigation of compound semiconductor crystal growth

Preparatory work on Bridgman directional solidification (BDS) of PbSnTe crystals prior to microgravity crystal growth experiments on Shuttle flights are reported. Gravitational effects become important in crystal growth when density gradients are present. The situation is critical in BDS of PbSnTe because of the necessity of obtaining homogeneous compositional distributions, which can be disturbed when convective processes occur. Numerical models have been defined which quantify the effects of convection in the crystal growth solution. The models were verified by earth-based crystal-growth tests in a two-zone furnace using equal concentrations of each of the elements. Data are provided to demonstrate the differences in composition among crystals grown at different orientations to the gravitational field vector.

Fripp, A. L.↗

NASA NTRS1985

Effects of supercooling in the initial solidification of PbTe-SnTe solid solutions

Deviations from compositions anticipated by the thermal equilibrium phase diagram have been observed in Bridgman-grown crystals of Pb(1-x)Sn(x)Te, in the first to freeze region of the boule. A set of experiments were conducted to determine the extent of thermal supercooling of Pb(1-x)Sn(x)Te in a Bridgman-like configuration. The results of the compositional profiles and the supercooling measurements are consistent with a diffusionless transformation occurring at the onset of solidification, and the length of uncontrolled growth is inversely related to the temperature gradient of the furnace.

Fripp, A. L.↗

NASA NTRS1986

Growth of crystals of several boron-carbon compositions by chemical vapor deposition

Boron-carbon compounds have been deposited by the flow of carbon tetrachloride and boron trichloride, in the presence of a large excess of hydrogen, over a graphite surface maintained at 1000-1300 C. Deposits were formed on either an RF-heated disc or a tube or insert heated by a resistance furnace. Crystalline materials ranging in composition from B2C to B17C have been obtained.

Kevill, D. N.↗

NASA NTRS1986

A procedure to visualize the melt-solid interface in Bridgman grown germanium and lead tin telluride

An X-ray and gamma-ray analysis technique has been developed which makes it possible to observe the melt solid interface during semiconductor crystal growth in a Bridgman furnace. Experiments have been carried out to observe the interface movement and shape in germanium as well as in lead tin telluride by means of the new method, and the results are discussed in detail. X-ray and gamma-ray radiographs of the melt-solid interfaces in the two semiconductor crystal specimens, are provided.

Barber, P. G.↗

NASA NTRS1986

Optimization of the Ni-Cr-Al-Y/ZrO2-Y2O3 thermal barrier system

The effects of bond and thermal barrier coating compositions, thicknesses, and densities on air plasma spray deposited Ni-Cr-Al-Y/ZrO2-Y2O3 life were evaluated in cyclic furnace oxidation tests at temperatures from 1110 to 1220 C. An empirical relation was developed to give life as a function of the above parameters. The thermal barrier system tested which had the longest life consisted of Ni-35.0 wt pct Cr-5.9 wt pct Al-0.95 wt pct Y bond coating and ZrO2-6.1 wt pct Y2O3 thermal barrier coating.

Stecura, S.↗

NASA NTRS1986

Burner rig corrosion of SiC at 1000 C

Sintered alpha-SiC was examined in both oxidation and hot corrosion with a burner rig at 400 kPa (4 atm) and 1000 C with a flow velocity of 94 m/s. Oxidation tests for times to 46 h produced virtually no attack, whereas tests with 4 ppm Na produced extensive corrosion in 13.5 h. Thick glassy layers composed primarily of sodium silicate formed in the salt corrosion tests. This corrosion attack caused severe pitting on the silicon carbide substrate and led to a 32 percent decrease in strength, compared to the as-received material. Parallel furnace tests of Na2SO4/air-induced attack yielded basically similar results, with slight product composition differences. The differences are explained in terms of the continuous sulfate deposition which occurs in a burner rig.

Jacobson, N. S.↗

NASA NTRS1986

Evaluation of the importance of the relative velocity during evaporation of drops in sprays

The importance of relative velocity past individual drops composing a burning spray with an envelope flame is estimated by applying the Bellan and Cuffel (1983) spray evaporation model to an ambient flow going around the spray without penetrating it. The model assumes a spherical spray composed of monodisperse uniformly distributed droplets which all move at the same speed, and relative gas/spray velocities, and spray radii used were representative of boiler and furnace operations. Numerical calculations indicate that the spray is more prone to ambient flow penetration for leaner mixtures (particularly for n = 1/cu cm), lower initial temperatures of gas phase and droplet, and more dilute spray configurations.

Bellan, J.↗

NASA NTRS1986

The use of silver in self-lubricating coatings for extreme temperatures

The advantages and disadvantages of elemental silver as a tribological material are discussed. It is demonstrated that the relatively high melting point of 961 deg C, softness, marked plasticity, and thermochemical stability of silver combine to make this metal useful in thin film solid lubricant coatings over a wide temperature range. Disadvantages of silver during sliding, except when used as a thin film, are shown to be gross ploughing due to plastic deformation under load with associated high friction and excessive transfer to counterface surfaces. This transfer generates an irregular surface topography with consequent undesirable changes in bearing clearance distribution. Research to overcome these disadvantages of element silver is described. A comparison is made of the tribological behavior of pure silver with that of silver formulated with other metals and high-temperature solid lubricants. The composite materials are prepared by co-depositing the powdered components with an airbrush followed by furnace heat treatment or by plasma-spraying. Composite coatings were formulated which are shown to be self-lubricating over repeated, temperature cycles from low temperature to about 900 deg C.

Sliney, H. E.↗

NASA NTRS1986

Quenched-in defects in flashlamp-annealed silicon

Deep levels introduced in boron-doped silicon by heat-pulse annealing with a tungsten-halogen flashlamp are investigated using deep-level transient spectroscopy. Two majority-carrier trapping levels in the band gap, at Ev + 0.32 eV and at Ev + 0.45 eV, are observed. These results are compared to those obtained by furnace-quenching and laser-annealing studies. Both the position in the gap and the annealing kinetics of the hole trap at Ev + 0.45 eV suggest that this center is due to an interstitial iron impurity in the lattice. The deep levels are not consistently observed in all flashlamp-annealed Si crystals utilized.

Borenstein, J. T.↗

NASA NTRS1986

Advanced thermal barrier system bond coatings for use on nickel-, cobalt- and iron-base alloy substrates

New and improved Ni-, Co-, and Fe-base bond coatings have been identified for the ZrO2-Y2O3 thermal barrier coatings to be used on Ni-, Co-, and Fe-base alloy substrates. These bond coatings were evaluated in a cyclic furnace between 1120 and 1175 C. It was found that MCrAlYb (where M = Ni, Co, or Fe) bond coating thermal barrier systems have significantly longer lives than MCrAlY bond coating thermal barrier systems. The longest life was obtained with the FeCrAlYb thermal barrier system followed by NiCrAlYb and CoCrAlYb thermal barrier systems in that order.

Stecura, S.↗

NASA NTRS1987

Heat-Exchanger/Heat-Pipe Interface

Monolithic assembly reliable and light in weight. Heat exchanger and evaporator ends of heat pipes integrated in monolithic halves welded together. Interface assembly connects heat exchanger of furnace, reactor, or other power source with heat pipes carrying heat to radiator or power-consuming system. One of several concepts proposed for nuclear power supplies aboard spacecraft, interface useful on Earth in solar thermal power systems, heat engines, and lightweight cooling systems.

Snyder, H. J.↗

NASA NTRS1987

Water-Cooled Optical Thermometer

Water-cooled optical probe measures temperature of nearby radiating object. Intended primarily for use in silicon-growing furnace for measuring and controlling temperatures of silicon ribbon, meniscus, cartridge surfaces, heaters, or other parts. Cooling water and flushing gas cool fiber-optic probe and keep it clean. Fiber passes thermal radiation from observed surface to measuring instrument.

Menna, A. A.↗

NASA NTRS1987

Vacuum Hold-Down System for Heat-Treating Thin Films

In improved furnace concept for heat-treating thin films, vacuum ports in vacuum plate(s) hold films connected together in zones so vacuum applied separately to each zone. Allows material being held to shrink or expand while still being held in place. Unclamped zones expand or contract , relieving local stresses so entire sheet accommades thermally induced changes without cracking. Applications include manufacture of thin semiconductor films for solar cells and of membranes for electrolytic production of oxygen.

Collins, Earl R., Jr.↗

NASA NTRS1987

Thermal-Barrier Coatings Containing Ytterbia

Resistance to thermal cycling increased. New outer ceramic coating layer for two-layer or graded thermal-barrier coating developed. Ceramic overlay zirconia stabilized with ytterbia and used in conjunction with NiCrAlY or NiCrAlYb bond coats. Two-layer system evaluated in furnace testing at temperatures cycled between 2,025 degrees F and 575 degrees F.

Stecura, Stephan↗

NASA NTRS1987

Meteoritic basalts: The nakhlites, their parental magmas, cooling rates, and equivalents on Earth

Field study in northern Ontario was planned to compare cumulate rocks reported in the literature with the nakhlites in order to study the crystallization rates of the nakhlites and their possible geological settings. Experimental studies have progressed slowly because of the demands of the field work and teaching. The furnace is fully functional, and its thermocouple and oxygen sensor cells are functional and calibrated.

Treiman, Allan H.↗

NASA NTRS1986

Growth and characterization of Hg(1-x)Zn(x)Se

Hg sub 1-xZn sub xSe alloys of composition x=0.10 were grown in a Bridgman-Stockbarger growth furnace at translation rates of 0.3 and 0.1 micron sec. The axial and radial composition profiles were determined using precision density measurements and IR transmission-edge-mapping, respectively. A more radially homogeneous alloy was produced at the slower growth rate, while the faster growth rate produced more axially homogeneous alloys. A determination of the electrical properties of the Hg sub 1-xZn sub xSe samples in the temperature range 300K-20K was also made. Typical carrier concentrations were on the order of magnitude of 10 to the 18th power cu/cm, and remained fairly constant as a function of temperature. A study was also made of the temperature dependence of the resistivity and Hall mobility. The effect of annealing in a selenium vapor on both the IR transmission and the electrical properties was determined. Annealing was effective in reducing the number of native donor defects and at the resulting lower carrier concentrations, charge carrier concentration was shown to be a function of temperature. Annealing caused the mobility to increase, primarily at the lower temperature, and the room temperature resistivity to increase. Annealing was also observed to greatly enhance the % IR transmittance of the samples. This was due primarily to the effect of annealing on decreasing the charge carrier concentration.

Andrews, R. N.↗