Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “attack surface”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,423 records · Page 79
All sourcesNASA NTRSDOE OSTI
NASA NTRS1989

Flow-field characteristics and normal-force correlations for delta wings from Mach 2.4 to 4.6

An experimental investigation has been conducted to determine the upper-surface flowfield types and the normal-force characteristics of a series of delta wing models at supersonic speeds. Flow-visualization data were used to classify the flowfields into seven primary types: shockless attached flow, separation bubble, classical vortex, vortex with shock, shock with no separation, shock-induced separation, and separation bubble with shock. The pressure distributions were integrated to obtain upper and lower surface normal-force loadings. A minimal effect of sweep was observed on the upper-surface normal force at constant Mach number and a minimal effect of Mach number was noted for the 75 deg delta wing lower-surface normal force. The normal-force coefficients for all test conditions were correlated, and a single empirical equation was formulated from which the normal-force coefficient could be calculated as a function of Mach number, angle of attack, and wing aspect ratio.

Covell, Peter F.↗
NASA NTRS1989

Low-speed, high-lift aerodynamic characteristics of slender, hypersonic accelerator-type configurations

Two investigations were conducted in the Langley 14 by 22 Foot Subsonic Tunnel to determine the low-speed aerodynamic characteristics of a generic hypersonic accelerator-type configuration. The model was a delta wing configuration incorporating a conical forebody, a simulated wrap-around engine package, and a truncated conical aftbody. Six-component force and moment data were obtained over a range of attack from -4 to 30 degrees and for a sideslip range of + or - 20 degrees. In addition to tests of the basic configuration, component build-up tests were conducted; and the effects of power, forebody nose geometry, canard surfaces, fuselage strakes, and engines on the lower surface alone were also determined. Control power available from deflections of wing flaps and aftbody flaps was also investigated and found to be significantly increased during power-on conditions. Large yawing moments resulted from asymmetric flow fields exhibited by the forebody as revealed by both surface pressure data and flow visualization. Increasing nose bluntness reduced the yawing-moment asymmetry, and the addition of a canard eliminated the yawing-moment asymmetry.

Gatlin, Gregory M.↗
NASA NTRS1987

CFD validation experiments at the Lockheed-Georgia Company

Information is given in viewgraph form on computational fluid dynamics (CFD) validation experiments at the Lockheed-Georgia Company. Topics covered include validation experiments on a generic fighter configuration, a transport configuration, and a generic hypersonic vehicle configuration; computational procedures; surface and pressure measurements on wings; laser velocimeter measurements of a multi-element airfoil system; the flowfield around a stiffened airfoil; laser velocimeter surveys of a circulation control wing; circulation control for high lift; and high angle of attack aerodynamic evaluations.

Malone, John B.↗
NASA NTRS1951

Effect of Fuselage and Tail Surfaces on Low-speed Yawing Characteristics of a Swept-wing Model as Determined in Curved-flow Test Section of Langley Stability Tunnel

Results are presented of a wind-tunnel investigation made to determine the influence of the fuselage and tail surfaces on the rotary derivatives in yawing flight of a transonic-airplane configuration having 45 degrees sweptback wing and tail surfaces. The tests were run in the curved-flow test section of the Langley stability tunnel at a Reynolds number of 1.07 X 10 to the sixth power and consisted of balance measurements throughout the angle-of-attack range for several flight-path radii of curvature. The results are compared with data from forced-oscillation and free-oscillation tests, and a description of testing techniques used is included.

WIND TUNNELS↗
NASA NTRS2016

Simulation of Sweep-Jet Flow Control, Single Jet and Full Vertical Tail

This work is a simulation technology demonstrator, of sweep jets used to suppress boundary layer separation and increase maximum achievable load coefficients. A sweep jet is a discrete Coanda jet that oscillates in the plane parallel to an aerodynamic surface. It injects mass and momentum in the approximate stream wise direction. It also generate turbulent eddies at the oscillation frequency, which are typically large relative to boundary layer turbulence, and which augmenting mixing across the boundary layer to attack flow separation. Simulations of a fluidic oscillator, the sweep jet emerging from the oscillator, and the suppression of boundary layer separation by an array of sweep jets are performed. Simulation results are compared to data from a dedicated CFD validation experiment of a single oscillator and its sweep jet, and from a study of a full-scale Boeing 757 vertical tail augmented with an array of sweep jets.2, 20 A critical step in the work is the development of realistic time-dependent sweep-jet in flow boundary conditions, derived from the results of the single-oscillator simulations, which create the sweep jets in the full-tail simulations. Simulations were performed using the Over flow CFD solver, with high-order spatial discretization and a range of turbulence modeling. Good results were obtained for all flows simulated, when suitable turbulence modeling was used.

flow control↗
NASA NTRS1988

Effects of surface perturbations on the asymmetric vortex flow over a slender body

An experimental investigation of the effects of surface perturbations on the asymmetric flow past a slender body has been conducted for laminar flow conditions. Beads with diameters ranging from 3/32 to 12/32 in. were attached near the apex of a cone/cylinder model having a base diameter of 3.5 in. and a cone semiapex angle of 9 deg at an angle of attack of 40 deg in an attempt to alter the sense of the asymmetric vortex flow pattern. Circumferential position as well as longitudinal location were varied to determine the most effective bead position. Whether or not the beads were effective in controlling the magnitude and direction of the vortex asymmetries was determined by 3 circumferential rows of pressure taps and by a helium-bubble flow visualization technique. The most effective circumferential position was found to be approximately 140 deg from the windward ray. While holding this circumferential position constant, the effect of bead size at three stations further along the body was also investigated. It was found that the size of the bead necessary to reverse the asymmetry increased more rapidly than the growth in cylinder radius. In general, these results indicate that discrete geometric imperfections on a body's surface can force asymmetry in a given direction if they are sufficiently large relative to the local radius.

Moskovitz, Cary A.↗
NASA NTRS1990

Unsteady aerodynamic loading of delta wings for low and high angles of attack

Experimental and theoretical investigations dealing with unsteady flow phenomena are surveyed, with the emphasis on the pattern of vortices which originate from flow separation at sharp leading edges. It is concluded that these vortices exhibit quasi-steady behavior when the alpha-vibrations are such that bursting instability does not occur above the wing surface. A selection of test results from Jarrah (1988) is presented and discussed. For sharp-edged delta models at low speeds, the aerodynamic loads which are plotted quantify the role of parameters AR and K for three ranges of alpha-variation. An extremely approximate and empirical 'theory' is offered, with data on crossflow drag and burst location, to reproduce the behavior of these airloads up to 90 deg. Recent attempts to apply the more sophisticated tools of computational fluid dynamics to the combination of unsteadiness and very high alpha are shown to be deficient.

Ashley, H.↗
NASA NTRS1998

Reduction and Analysis of Phosphor Thermography Data With the IHEAT Software Package

Detailed aeroheating information is critical to the successful design of a thermal protection system (TPS) for an aerospace vehicle. This report describes NASA Langley Research Center's (LaRC) two-color relative-intensity phosphor thermography method and the IHEAT software package which is used for the efficient data reduction and analysis of the phosphor image data. Development of theory is provided for a new weighted two-color relative-intensity fluorescence theory for quantitatively determining surface temperatures on hypersonic wind tunnel models; an improved application of the one-dimensional conduction theory for use in determining global heating mappings; and extrapolation of wind tunnel data to flight surface temperatures. The phosphor methodology at LaRC is presented including descriptions of phosphor model fabrication, test facilities and phosphor video acquisition systems. A discussion of the calibration procedures, data reduction and data analysis is given. Estimates of the total uncertainties (with a 95% confidence level) associated with the phosphor technique are shown to be approximately 8 to 10 percent in the Langley's 31-Inch Mach 10 Tunnel and 7 to 10 percent in the 20-Inch Mach 6 Tunnel. A comparison with thin-film measurements using two-inch radius hemispheres shows the phosphor data to be within 7 percent of thin-film measurements and to agree even better with predictions via a LATCH computational fluid dynamics solution (CFD). Good agreement between phosphor data and LAURA CFD computations on the forebody of a vertical takeoff/vertical lander configuration at four angles of attack is also shown. In addition, a comparison is given between Mach 6 phosphor data and laminar and turbulent solutions generated using the LAURA, GASP and LATCH CFD codes. Finally, the extrapolation method developed in this report is applied to the X-34 configuration with good agreement between the phosphor extrapolation and LAURA flight surface temperature predictions. The phosphor process outlined in the paper is believed to provide the aerothermodynamic community with a valuable capability for rapidly obtaining (4 to 5 weeks) detailed heating information needed in TPS design.

Merski, N. Ronald↗
NASA NTRS1990

Effect of tail size reductions on longitudinal aerodynamic characteristics of a three surface F-15 model with nonaxisymmetric nozzles

An investigation was conducted in the Langley 16-Foot Transonic Tunnel to determine the effects of horizontal and vertical tail size reductions on the longitudinal aerodynamic characteristics of a modified F-15 model with canards and 2-D convergent-divergent nozzles. Quantifying the drag decrease at low angles of attack produced by tail size reductions was the primary focus. The model was tested at Mach numbers of 0.40, 0.90, and 1.20 over an angle of attack of -2 degree to 10 degree. The nozzle exhaust flow was simulated using high pressure air at nozzle pressure ratios varying from 1.0 (jet off) to 7.5. Data were obtained on the baseline configuration with and without tails as well as with reduced horizontal and/or vertical tail sizes that were 75, 50, and 25 percent of the baseline tail areas.

Frassinelli, Mark C.↗
DOE OSTI2024

Intergranular corrosion of Ni-30Cr in high-temperature hydrogenated water after removing surface passivating film

Abstract High-resolution transmission electron microscopy and atom probe tomography are used to characterize the initial passivation and subsequent intergranular corrosion of degraded grain boundaries in a model Ni-30Cr alloy exposed to 360 °C hydrogenated water. Upon initial exposure for 1000 h, the alloy surface directly above the grain boundary forms a thin passivating film of Cr 2 O 3 , protecting the underlying grain boundary from intergranular corrosion. However, the metal grain boundary experiences severe Cr depletion and grain boundary migration during this initial exposure. To understand how Cr depletion affects further corrosion, the local protective film was sputtered away using a glancing angle focused ion beam. Upon further exposure, the surface fails to repassivate, and intergranular corrosion is observed through the Cr-depleted region. Through this combination of high-resolution microscopy and localized passive film removal, we show that, although high-Cr alloys are resistant to intergranular attack and stress corrosion cracking, degradation-induced changes in the underlying metal at grain boundaries make the material more susceptible once the initial passive film is breached.

(S)TEM↗
DOE OSTI2024

Convergent ab initio analysis of the multi-channel HOBr + H reaction

High-level potential energy surfaces for three reactions of hypobromous acid with atomic hydrogen were computed at the CCSDTQ/CBS//CCSDT(Q)/complete basis set level of theory. Focal point analysis was utilized to extrapolate energies and gradients for energetics and optimizations, respectively. The H attack at Br and subsequent Br–O cleavage were found to proceed barrierlessly. The slightly submerged transition state lies −0.2 kcal mol−1 lower in energy than the reactants and produces OH and HBr. The two other studied reaction paths are the radical substitution to produce H2O and Br with a 4.0 kcal mol−1 barrier and the abstraction at hydrogen to produce BrO and H2 with an 11.2 kcal mol−1 barrier. The final product energies lie −37.2, −67.9, and −7.3 kcal mol−1 lower in energy than reactants, HOBr + H, for the sets of products OH + HBr, H2O + Br, and H2 + BrO, respectively. Additive corrections computed for the final energetics, particularly the zero-point vibrational energies and spin–orbit corrections, significantly impacted the final stationary point energies, with corrections up to 6.2 kcal mol−1.

Chemistry↗
NASA NTRS1971

Dynamic upper atmospheric force model on stabilized vehicles for a high-precision trajectory computer program

The upper atmosphere model draws heavily on the behavior of the earth's upper atmosphere which exhibits cyclic as well as irregular variations in density profile, temperature, pressure, and composition in unison with solar activities as deduced from the more recent land-based and satellite observations. The lift and drag model is designed specifically for inertially stabilized vehicles of the Mariner class, with possible extension to gravity gradient stabilized vehicles of the GEOS class. The model considers operation in the free molecular flow regimes with large Knudsen numbers. The vehicle is considered a composite structure with basic components having well-defined shapes, each with its own surface characteristics in terms of temperature, reflectivity, and accommodation of free stream molecules. The model takes into account both the calculation of precise aerodynamic force coefficients in terms of expansion of modified Bessel functions in speed ratios and angle of attack, and approximate force coefficients when the speed ratios approach infinity. Other considerations include specular and diffused reflectivity, shielding, and shadow effects.

Khatib, A. R.↗
NASA NTRS1974

Results of tests OA63 and IA29 on an 0.015 scale model of the space shuttle configuration 140 A/B in the NASA/ARC 6- by 6-foot transonic wind tunnel, volume 1

Tests were conducted in the NASA/ARC 6- by 6-foot transonic wind tunnel from September 12 to September 28, 1973 on an 0.015-scale model of the space shuttle configuration 140 A/B. Surface pressure data were obtained for the orbiter for both launch and entry configuration at Mach numbers from 0.6 to 2.0. The surface pressures were obtained in the vicinity of the cargo bay door hinge and parting lines, the side of the fuselage at the crew compartment and below the OMS pods at the aft compartment. Data were obtained at angles of attack and sideslip consistent with the expected divergencies along the nominal trajectory. These tests were first in a series of tests supporting the orbiter venting analysis. The series will include tests in three facilities covering a total Mach number range from 0.6 to 10.4.

Spangler, R. H.↗
NASA NTRS1975

Airloads investigation of an 0.030-scale model of the space shuttle vehicle 140A/B launch configuration (model 47-OTS) in the arc 11-foot unitary plan wind tunnel for Mach range 0.6 to 1.4 (IA14A), Volume 2

Results of tests conducted on an 0.030-scale launch configuration model of the space shuttle vehicle 140A/B in the NASA/ARC 11-foot unitary plan wind tunnel are presented. Aerodynamic loads data were obtained at Mach numbers from 0.6 to 1.4. Surface pressure distributions were obtained simultaneously with six-component stability and control force data on the complete launch configuration. The configuration consisted of the orbiter, an external tank, two solid rocket boosters, and associated intercomponent attach hardware. Angles of attack and sideslip from -10 degrees to +10 degrees were investigated.

Gillins, R. L.↗
NASA NTRS1975

Airloads investigation of an 0.030-scale model of the space shuttle vehicle 140A/B launch configuration (model 47-OTS) in the arc 11-foot unitary plan wind tunnel for Mach range 0.6 to 1.4 (IA14A), volume 1

The results of the tests are presented along with aerodynamic loads data obtained at Mach numbers from 0.6 to 1.4. Surface pressure distributions were obtained simultaneously with six-component stability and control force data on the complete launch configuration. The configuration consisted of the orbiter, an external tank, two solid rocket boosters, and associated intercomponent attach hardware. Angles of attack and sideslip from -10 deg to +10 deg were investigated. The tests were conducted from 4 September 1973 through 13 September 1973.

Gillins, R. L.↗
NASA NTRS1977

Burner rig alkali salt corrosion of several high temperature alloys

The hot corrosion of five alloys was studied in cyclic tests in a Mach 0.3 burner rig into whose combustion chamber various aqueous salt solutions were injected. Three nickel-based alloys, a cobalt-base alloy, and an iron-base alloy were studied at temperatures of 700, 800, 900, and 1000 C with various salt concentrations and compositions. The relative resistance of the alloys to hot corrosion attack was found to vary with temperature and both concentration and composition of the injected salt solution. Results indicate that the corrosion of these alloys is a function of both the presence of salt condensed as a liquid on the surface and of the composition of the gas phases present.

Deadmore, D. L.↗
NASA NTRS1993

Subsonic aerodynamic characteristics of the HL-20 lifting-body configuration

The HL-20 is proposed as a possible future manned spacecraft. The configuration consists of a low-aspect-ratio body with a flat undersurface. Three fins (a small centerline fin and two outboard (tip) fins set at a dihedral angle of 50 deg) are mounted on the aft body. The control system consists of elevon surfaces on the outboard fins, a set of four body flaps on the upper and lower aft body, and an all-movable center fin. Both the elevons and body flaps were capable of trimming the model to angles of attack from -2 deg to above 20 deg. The maximum trimmed lift-drag ratio was 3.6. Replacing the flat-plate tip fins with airfoil tip fins increased the maximum trimmed lift-drag ratio to 4.2. The elevons were effective as a roll control, but they produced about as much yawing moment as rolling moment because of the tip-fin dihedral angle. The body flaps produced less rolling moment than the elevons and only small values of yawing moment. A limited investigation of the effect of varying tip-fin dihedral angle indicated that a dihedral angle of 50 deg was a reasonable compromise for longitudinal and lateral stability, longitudinal trim, and performance at subsonic speeds.

Ware, George M.↗
NASA NTRS1995

Numerical study to assess sulfur hexafluoride as a medium for testing multielement airfoils

A methodology is described for computing viscous flows of air and sulfur hexafluoride (SF6). The basis is an existing flow solver that calculates turbulent flows in two dimensions on unstructured triangular meshes. The solver has been modified to incorporate the thermodynamic model for SF6 and used to calculate the viscous flow over two multielement airfoils that have been tested in a wind tunnel with air as the test medium. Flows of both air and SF6 at a free-stream Mach number of 0.2 and a Reynolds number of 9 x 10(exp 6) are computed for a range of angles of attack corresponding to the wind-tunnel test. The computations are used to investigate the suitability of SF6 as a test medium in wind tunnels and are a follow-on to previous computations for single-element airfoils. Surface-pressure, lift, and drag coefficients are compared with experimental data. The effects of heavy gas on the details of the flow are investigated based on computed boundary-layer and skin-friction data. In general, the predictions in SF6 vary little from those in air. Within the limitations of the computational method, the results presented are sufficiently encouraging to warrant further experiments.

Bonhaus, Daryl L.↗