Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Unconventional”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,423 records · Page 79
All sourcesNASA NTRSDOE OSTI
NASA NTRS2020

Optimization of Low Reynolds Number Airfoils for Martian Rotor Applications Using an Evolutionary Algorithm

The Mars Helicopter (MH) will be flying on the NASA Mars 2020 rover mission scheduled to launch in July of 2020. Research is being performed at the Jet Propulsion Laboratory (JPL) and NASA Ames Research Center to extend the current capabilities and develop the Mars Science Helicopter (MSH) as the next possible step for Martian rotorcraft. The low atmospheric density and the relatively small-scale rotors result in very low chord-based Reynolds number flows over the rotor airfoils. The low Reynolds number regime results in rapid performance degradation for conventional airfoils due to laminar separation without reattachment. Unconventional airfoil shapes with sharp leading edges are explored and optimized for aerodynamic performance at representative Reynolds-Mach combinations for a concept rotor. Sharp leading edges initiate immediate flow separation, and the occurrence of large-scale vortex shedding is found to contribute to the relative performance increase of the optimized airfoils, compared to conventional airfoil shapes. The oscillations are shown to occur independent from laminar-turbulent transition and therefore result in sustainable performance at lower Reynolds numbers. Comparisons are presented to conventional airfoil shapes and peak lift-to-drag ratio increases between 17% and 41% are observed for similar section lift.

Koning, Witold J.↗
NASA NTRS2019

Citizen Science Twitter Data Management for Earth Science Applications

Social media data can provide useful real-time and historical information relating to the natural world, but managing this data poses challenges. Scientists at GES DISC are exploring the potential of Twitter data to augment precipitation data from the Global Precipitation Measurement (GPM) mission. However, the format of Twitter data is unconventional in the context of NASA data centers, resulting in frustration for scientists who need to work with the data. This study investigated procedures and standards needed to properly manage Twitter data to make them compatible with these data centers. After comparing databases, the study found that the MongoDB database was best suited for the storage of raw Twitter data due to its flexibility, ability to be accessed by multiple users, and querying functionality. The study used the Python package Zarr to transform processed Twitter data into a gridded format similar to that of satellite data. Each Tweet was mapped onto a time-space grid; each grid location contained information about Tweet attributes and precipitation. The study developed a pipeline for downloading, storing, and gridding Twitter data and transformed Twitter data into an understandable format for users of NASA satellite data.

Li, Rachel↗
NASA NTRS2020

Generation and Calibration of Linear Models of Aircraft with Highly Coupled Aeroelastic and Flight Dynamics

The lightweight structures and unconventional configurations being considered for the next generation of aircraft mean that any effort to predict or control the flight dynamics is impacted by the structural dynamics. One of the most severe forms of coupling between aeroelasticity and flight dynamics is an instability called body freedom flutter. The existing tools often assume a relatively weak effect of structural dynamics on the flight dynamics, and are therefore incapable of modeling strong interactions like body freedom flutter. A method of combining different sources of data traditionally used for aeroelasticity and flight dynamics is described by reconciling many of the differences between these models. By building upon past modeling efforts, a level of familiarity in the approach is achieved. Generally the differences from the traditional approaches are subtle but significant. The traditional frequency domain flutter model in a modal coordinate system is converted to a form consistent with a time domain flight dynamics model. The time domain rational function approximation about a non-inertial coordinate system and the unique constraints for the conversion between the inertial and non-inertial coordinate systems are discussed. A consistent transformation of the states of aeroelastic models to flight dynamics models is derived, which enables the integration of data from higher fidelity computational fluid dynamics models or wind-tunnel testing. The present method of integrating multidisciplinary data was used to create models that compare well with X-56A flight-test data, including conditions past the flutter speed.

Ouellette, Jeffrey↗
NASA NTRS2020

Aircraft Analysis Using the Layered and Extensible Aircraft Performance System (LEAPS)

The Layered and Extensible Aircraft Performance System (LEAPS) is a new air- craft analysis tool being developed by members of the Aeronautics Systems Analysis Branch (ASAB) and the Vehicle Analysis Branch (VAB) at NASA Langley Research Center. LEAPS will enable the analysis of advanced aircraft concepts and architec- tures that include electric and hybrid-electric propulsion systems. The development of LEAPS is motivated by the analysis gaps found in traditional aircraft analysis tools such as the Flight Optimization System (FLOPS). FLOPS has been the tool of choice of the ASAB for over 30 years and has proven to be a reliable analysis tool for conventional aircraft. However, FLOPS is not suitable to analyze the cur- rent unconventional vehicles that are of interest to industry, government agencies, and academia. In contrast, LEAPS is being developed with a flexible architecture that leverages new analysis methodologies that will enable the analysis of unconven- tional aircraft. This paper presents the first complete working version of LEAPS by showing the analysi at include fuel-based and hybrid-electric conceptual aircraft.

Capristan, Francisco M.↗
NASA NTRS2019

Flutter Prediction for Aircraft Conceptual Design

Flutter prediction is usually a knowledge-based analysis process that aims to reduce the cost of aeroelastic stability margin certification. However, early detection of flutter problems is beneficial in the development of unconventional aircraft. The recently developed automation tool ConceptFEA for structural sizing of aircraft concepts paves the way for rapid physics-based flutter prediction of aircraft concepts. A match-point iteration procedure using the p-k method is implemented for ConceptFEA with minimum user input requirements to generate flutter boundary points. A subsonic business jet concept and its high aspect-ratio wing variant are used to demonstrate how the newly developed flutter prediction capability can be used during aircraft conceptual design. Sized structures, flutter boundary curves, and flutter sensitivity analysis results are generated for these two concepts using ConceptFEA. The relevant equivalent plate theory is provided to show the quantitative relationships between a stiffened panel and its equivalent NASTRAN PSHELL panel. The rapid flutter prediction capability of ConceptFEA makes multidisciplinary collaborations between systems analysts and aeroelasticity experts feasible in practice.

Li, Wu↗
NASA NTRS2019

Far Term Noise Reduction Roadmap for the NASA D8 and Single-Aisle Tube-And-Wing Aircraft Concepts

A portfolio of noise reduction technologies is applied to two advanced single-aisle class vehicle concepts in order to evaluate the prospects for these aircraft to meet the NASA Far Term noise goals, beyond 2035. TheNASAD8 (ND8) aircraft is an unconventional configuration with boundary-layer ingesting engines mounted in the aft dorsal location. The 160-passenger tube-and-wing (TW160) aircraft is a conventional configuration with podded engines located under the wing, which represents an incremental evolution of current design philosophies. The noise reduction technologies were chosen to be compatible with each aircraft’s specific configuration requirements. The acoustic effects were predicted based on experimental and numerical studies, andwere incorporated into the prediction of total system noise usingNASA’s research-level Aircraft NOise Prediction Program (ANOPP-Research). Results suggest that the unfavorable Propulsion Airframe Aeroacoustic (PAA) effects of the two aircraft considered here significantly limit their prospects of meeting NASA’s Far Term noise goal, and that further development of the technology portfolio is key to ensuring future success in addressing the noise challenges for single-aisle class vehicles.

Clark, Ian A.↗
NASA NTRS2019

An Investigation of Bifurcation Acoustic Treatment Effects on Aft-Fan Engine Nacelle Noise

Increasing air traffic and more stringent aircraft noise regulations continue to expand requirements on aircraft noise reduction capabilities for conventional and unconventional aircraft configurations. A major component of the overall aircraft noise is the sound associated with the propulsion system mounted in the engine nacelle. Acoustic liners mounted in the aircraft engine nacelles provide a significant portion of the current fan noise reduction. However, they must be further optimized if challenging noise reduction goals are to be achieved. One area within the aft bypass duct that may be an excellent candidate for increased attention is the acoustic treatment on the engine bifurcations (i.e., engine pylon and lower bifurcation). This paper describes a fundamental study of the effects of bifurcation treatment on simulated aft fan noise, as well as the validation of numerical tools to predict such effects. Five bifurcation configurations (four treated and one hardwall) were fabricated and tested in the NASA Langley Curved Duct Test Rig. Results show that mode scattering may occur due to both the presence of the bifurcation, as well as variable impedance distributions on the bifurcation surface. Future work will also include optimization of bifurcation treatments for testing in the Curved Duct Test Rig. These initial results are promising and this work provides valuable information for further study and improvement of the performance of bifurcation acoustic treatments.

Nark, Douglas M.↗
NASA NTRSDate not supplied

TPSAS-NF1676L-14659-DND

Subsonic fixed wing aircraft dominant the world's air fleet and move people and goods on 24/7 basis. While air travel is an effective, efficient means of transportation providing an unmatched combination of speed and range, future subsonic aircraft must continue to improve substantially to meet energy efficiency and environmental compatibility goals. The NASA Fundamental Aeronautics Program via the Subsonic Fixed Wing (SFW) Project addresses the comprehensive challenge of enabling revolutionary energy-efficiency improvements in subsonic transport aircraft combined with dramatic reductions in harmful emissions and perceived noise to facilitate sustained growth of the air transportation system. Advanced technologies and the development of unconventional aircraft systems offer the potential to achieve these improvements. Multidisciplinary advances are required in aerodynamic efficiency to reduce drag, structural efficiency to reduce aircraft empty weight, and propulsive and thermal efficiency to reduce thrust-specific energy consumption (TSEC) for overall system benefit. Additionally, advances are required to reduce perceived noise without adversely affecting drag, weight, or TSEC and to reduce harmful emissions without adversely affecting energy efficiency or noise. The primary focus of SFW is on the "N+3" generation; that is, vehicles that are three generations beyond the current state of the art, requiring mature technology solutions in the 2025-30 timeframe. Success in overcoming these technical challenges will result in major changes to engine cycle and airframe configurations, which in turn will broaden the technology trade space for vehicles ranging from large transports to very light jets. This presentation provides an overview of SFW-sponsored research targeted at improved aerodynamic and structural efficiency for airframe and integrated vehicle systems.

Richard A Wahls↗
NASA NTRS2020

Antenna and Flight Control Software for Conformal Phased Array Antenna Design (CPAAD)

The National Aeronautics and Space Administration (NASA) is developing lightweight conformal phased array antenna designs (CPAAD) for beyond line of sight communications [1]. The CPAAD system is developed to address reliable and affordable autonomous next generation aviation systems. The technology takes advantage of newly assigned provisional Ku-bands for UAVs. The antenna design is unique to avoid interference with the ground and the unconventional substrate reduces weight. The surface mounted conformal design allows for reduced drag during flight. The software developed for the CPAAD system operates the antenna hardware and provides a graphic user interface (GUI) for ground testing and flight operations.

phased array antenna control software↗
NASA NTRS2021

Aircraft System Noise of the NASA D8 Subsonic Transport Concept

A vehicle-level noise assessment has been performed for the NASA D8 (ND8) concept aircraft in the NASA Advanced Air Transport Technology Project portfolio. The NASA research-level Aircraft Noise Prediction Program was used to predict the noise from each source component on the ND8 to build up a noise estimate for the full aircraft. The propulsion airframe aeroacoustic effects of the ND8 (namely, boundary-layer ingestion, with its influence on fan noise; and the noise shielding, reflection, and diffraction mechanisms of the unconventional airframe) were empirically modeled using experimental data. Far-term noise reduction technology concepts were modeled and added to the noise prediction to evaluate the low-noise potential of the ND8 in the far-term timeframe. Results indicate that the increase in fan noise due to boundary-layer ingestion, as well as the lack of aft shielding, prevents the aircraft from approaching NASA’s noise goals for either the midterm or far term. The aircraft achieves margins to Stage 4 of only 9.4 and 17.3 effective perceived noise in decibels (EPNdB) in the midterm and far-term configurations, respectively, compared with goals of 32–42 EPNdB in the midterm and 42-52 EPNdB in the far term.

aircraft system noise↗
NASA NTRSDate not supplied

Pterodactyl: Guidance and Control of a Symmetric Deployable Entry Vehicle using an Aerodynamic Control System

The NASA-funded Pterodactyl project seeks to advance the state-of-the-art for varying entry vehicle types by developing unconventional guidance and control technologies for Deployable Entry Vehicles (DEVs) that can be applied to different entry vehicle configurations. Prior work by the authors [1–5] involved developing both traditional and novel integrated guidance and control solutions for a Pterodactyl Baseline Vehicle (PBV), a variant of an asymmetric DEV called the Lifting Nano ADEPT (LNA) [6]. In the prior studies, two different guidance schemes were designed and implemented for the PBV: (i) traditional bank angle guidance developed using the Fully Numerical Predictor-Corrector Entry Guidance (FNPEG) and (ii) novel angle of attack and sideslip (α - β) guidance developed using FNPEG with Uncoupled Range Control [4]. Using Linear Quadratic Regulator (LQR) optimal control methods with state-feedback integral control designs, these guidance trajectories were designed to be tracked using (i) a conventional propulsive entry vehicle control hardware architecture - reaction control systems (RCS) and (ii) novel non-propulsive entry vehicle control systems - aerodynamic flap control system (FCS) and moving mass control system (MMCS) [1]. The novel FCS and MMCS architectures were designed to track α - β guidance commands while the RCS was designed to track bank angle commands. It was discovered that the asymmetric DEV, the PBV, experienced a non-zero induced roll moment due to sideslip that the FCS and MMCS architectures had limited capability to trim out. These two architectures were designed to provide independent angle of attack and sideslip commands with limited consideration for roll moment generation to trim. As a result, for the PBV, the FCS and MMCS configurations as designed, were limited in providing the control authority needed to track an α - β guidance trajectory [1]. These results form the motivation for the work presented in this paper - utilizing an aerodynamic control system to track α - β guidance commands for a symmetric DEV with the expectation that a symmetric entry vehicle will have zero or significantly reduced roll moment due to sideslip that the FCS can handle when tracking an α - β guidance trajectory. To demonstrate the feasibility of a novel guidance and control architecture on a DEV, we utilize a symmetric DEV, the PBV-II, for (i) the novel α - β guidance development using FNPEG with Uncoupled Range Control and (ii) LQR control design using eight aerodynamic control surfaces. This paper demonstrates that the novel uncoupled α - β guidance tracking can be achieved using aerodynamic control surfaces on a symmetric deployable entry vehicle configuration.

Wendy A Okolo↗
NASA NTRS2020

Measuring Large Amplitude Surface Figure Error using Coordinate Metrology

Advances in optical testing are as important as advances in optical fabrication, because one can make only what one can measure, particularly for unconventional prescriptions, like aspheric and freeform optics. A new, high-precision metrology capability is utilized to close the gap between interferometric testing and lower precision, contact-probe-based coordinate measuring machines or laser tracker/radar metrology to accurately measure surfaces with large figure error. This nearly universal optical testing method employs an ultra-precision coordinate measuring machine equipped with a non-contact probe. It was developed to characterize a broad spectrum of optical surfaces including ones with high slopes, impossible to measure using traditional interferometric testing. Optical components, covering a wide range of prescriptions, such as large convex conics, high-sloped aspherics, grazing-incidence x-ray optics, and highly deformed flats, were successfully measured. The resulting data were reduced using custom-developed routines to determine the optic’s alignment, surface departure from design, and the as-built optical prescription. This information guided the fabrication and modeling of these optical components

Manal Khreishi↗
NASA NTRS2021

Center for High-Efficiency Electrical Technologies for Aircraft (CHEETA)

The aeronautics industry has been challenged on many fronts to increase efficiency, reduce emissions, and decrease dependency on carbon-based fuels. With subsonic transports serving as the dominant contributor to the fuel consumption and carbon footprint of global aviation, the need for environmentally-responsible transportation has been met with a boom of research in the field of aircraft propulsion electrification across industry, government, and academic organizations. However, adoption of electrified propulsion systems for large commercial aircraft today is unattainable, due to the lack of motors and power electronics appropriately sized for these vehicles, high weight requirements of conventional electrical energy storage systems, and new principles required to design these classes of aircraft. The mission of the Center for High-Efficiency Electrical Technologies for Aircraft (CHEETA) program is to develop, mature, and design disruptive technologies for electric commercial aviation. The associated technologies being researched include distributed aero-propulsion system integration, high-efficiency electrochemical power conversion, flight-weight electric machines and power electronics, materials and systems for superconducting high-efficiency power transmission, and methods for complex system integration and optimization. Additionally, the current program is investigating the use of unconventional energy storage and power generation architectures, such as liquid hydrogen fuel and high-efficiency fuel cell systems. The research program provides a direct line-of-sight to not only achieving, but potentially even exceeding the aviation community goals for transition to alternative propulsion and energy through convergence of various novel technologies. The end result of maturation and integration of these technologies is an aircraft system with a quiet, efficient propulsion system that produces zero carbon dioxide, nitrogen oxides, and particulate matter emissions at the vehicle level.

Koushik Datta↗
NASA NTRSDate not supplied

Twinned magnetite in granitic samples from the Siljan impact structure, Sweden

Impact cratering is a ubiquitous process throughout the solar system and has played a key role for the geologic evolution of Earth and other planets [1]. Magnetic anomalies are common characteristics of impact craters [2], so understanding how magnetite (Fe23+Fe2+O42-), an important magnetic carrier in both terrestrial and extraterrestrial rocks, is affected by shock waves, especially structurally and magnetically, is crucial. Magnetic minerals have been studied to gain insight into the geologic evolution of Mars, with specific focus including understanding the Martian crustal structure and the oxidization state of Martian rocks (e.g., [3,4,5]). Shock waves permanently alter the intrinsic magnetic properties of rocks (e.g., [6]), as do twinning in natural environments with less extreme P/T conditions [7]. In fact, pressure conditions induced by impacts have been suggested to explain demagnetization signatures observed around Martian impact basins [8]. It is still poorly understood what effects shock has on the crystallographic structure of magnetite and thus it’s intrinsic magnetic properties, and , how that affects the bulk magnetic properties of rocks (e.g., [9]). Limited experimental studies have investigated the effects of shock compression on magnetite, especially with the aim of describing crystallographic deformation (e.g., [9] and references therein). In this work we report preliminary results of an investigation of microstructures in magnetite, an “unconventional” mineral in shock studies, in granitic samples from the ca. 380 Ma ~52 km-in-diameter Siljan impact structure, located in south-central Sweden.

shock metamorphism↗
NASA NTRS1996

Mars Pathfinder Cruise Stage/Entry Vehicle Separation Dynamics

Prior to atmospheric entry, Mars Pathfinder flight system will separate its entry vehicle from its cruise stage, and establish the entry conditions for a passive and unconventional entry, descent, and landing approach. This paper summarizes a separation dynamics analysis conducted to demonstrate that the cruise separation system design is viable and ensure that adequate design margins exist with the effects from parameter uncertainty included.

Pathfinder↗
NASA NTRSDate not supplied

Urban Air Mobility: A Control-Centric Approach to Addressing Technical Challenges

Urban Air Mobility (UAM) is an emerging aviation sector and is playing an integral part in the on-demand mobility revolution. UAM is powered by the convergence of advances in distributed electrical propulsion (DEP) and vehicle autonomy. The complexity of operations in the urban environment and the unconventional vehicle configurations designed to take advantage of new propulsion technologies, result in numerous challenges that benefit from a control-centric approach. In this talk we outline some of these challenges and present our current approach to addressing them. For example, in order to achieve full market potential and access to UAM, vehicle autonomous flight is required. A key barrier to autonomous flight in a large multi-agent system is dealing with off-nominal situations and contingencies in a safe and predictable manner. We present our approach to intelligent contingency management, and share recent results and open problems. Additionally, we discuss another major barrier to ubiquitous UAM – the noise signature produced by vehicles with multiple rotors. We present our approach to minimizing such noise within the framework of the acoustically-aware vehicle.

UAM↗
NASA NTRSDate not supplied

Integrated Design Results for the MSR SRC Mars Ascent Vehicle

The primary mission of the NASA Mars Sample Return (MSR) Campaign is to return samples of the Martian surface to Earth for scientific study. As part of this campaign, NASA is developing a Mars Ascent Vehicle (MAV). This vehicle must survive an approximate two year journey to the Martian surface as a payload aboard a separate lander spacecraft. After residing on the surface for another year, the MAV will carry a payload of samples into orbit. From there, following ejection from the MAV, the samples will rendezvous with an Earth return spacecraft for capture, and ultimately, return to Earth.The design of the MAV represents a number of unique challenges, as no launch vehicle has ever left the surface of a planet other than Earth. Although conceptual designs for a MAV have been in various levels of development since the 1970s, none have achieved the level of fidelity and support that exists in the current MSR-MAV design. Early MSR-MAV concept studies examined multiple methods of propulsion, ultimately deciding that a Two Stage to Orbit (TSTO) solid propulsion vehicle would provide the most capable performance in a Martian environment. Following this key architecture decision, the vehicle design was further matured to a Solid-Solid Guided-Guided (SSGG) architecture for NASA Key Decision Point A (KDP-A). Although the SSGG design was able to meet all mission constraints, concerns were raised regarding limited mass margin on other elements of the MSR campaign at such an early phase. A design challenge was issued to reduce MAV total mass by as much as possible. It was ultimately determined that by moving a number of components of the vehicle second stage to the first stage, the overall vehicle mass could be reduced significantly. The new design featured a much smaller and completely unguided second stage. This paper describes the resultant Solid-Solid Guided-Unguided (SSGU) MAV design concept developed as part of the Systems Requirement Cycle (SRC). This design was developed primarily by NASA Marshall Space Flight Center (MSFC), in association with NASA Jet Propulsion Laboratory (JPL) and NASA Langley Research Center (LaRC). The TSTO vehicle includes one solid rocket motor per stage. As the vehicle second stage is unguided, it features spin-stabilization to maintain vehicle stability during flight. An electromechanically actuated Thrust Vector Control (TVC) and a monopropellant Reaction Control System (RCS) is employed for active guidance on the first stage. The vehicle is designed to deliver up to 0.47kg of Martian samples to a Mars circular orbit of 380km at 27° inclination. Due to the extremely unique design constraints of this mission, and a recent transition to a Risk Class A posture, the MAV team was compelled to devise unconventional solutions to the vehicle design. The detailed design and analysis of these subsystems and the vehicle as a whole are discussed in this paper relative to all of the engineering disciplines involved.

MSR↗
NASA NTRSDate not supplied

Integrated Design Results for the MSR SRC Mars Ascent Vehicle

The primary mission of the NASA Mars Sample Return (MSR) Campaign is to return samples of the Martian surface to Earth for scientific study. As part of this campaign, NASA is developing a Mars Ascent Vehicle (MAV). This vehicle must survive an approximate two-year journey to the Martian surface as a payload aboard a separate lander spacecraft. After residing on the surface for another year, the MAV will carry a payload of samples into orbit. From there, following ejection from the MAV, the samples will rendezvous with an Earth return spacecraft for capture, and ultimately, return to Earth. The design of the MAV represents a number of unique challenges, as no launch vehicle has ever left the surface of a planet other than Earth. Although conceptual designs for a MAV have been in various levels of development since the 1970s, none have achieved the level of fidelity and support that exists in the current MSR-MAV design. Early MSR-MAV concept studies examined multiple methods of propulsion, ultimately deciding that a Two-Stage-to-Orbit (TSTO) solid propulsion vehicle would provide the most capable performance in a Martian environment. Following this key architecture decision, the vehicle design was further matured to a Solid-Solid Guided-Guided (SSGG) architecture for NASA Key Decision Point A (KDP-A). Although the SSGG design was able to meet all mission constraints, concerns were raised regarding limited mass margin on other elements of the MSR campaign at such an early phase. A design challenge was issued to reduce MAV total mass by as much as possible. It was ultimately determined that by moving a number of components of the vehicle second stage to the first stage, the overall vehicle mass could be reduced significantly. The new design features a much smaller and completely unguided second stage. This paper describes the resultant Solid-Solid Guided-Unguided (SSGU) MAV design concept developed as part of the Systems Requirement Cycle (SRC). This design was developed primarily by NASA Marshall Space Flight Center (MSFC), in association with NASA Jet Propulsion Laboratory (JPL) and NASA Langley Research Center (LaRC). The TSTO vehicle includes one solid rocket motor per stage. As the vehicle second stage is unguided, it features spin-stabilization to maintain vehicle stability during flight. An electromechanically actuated Thrust Vector Control (TVC) system and a monopropellant Reaction Control System (RCS) are employed for active guidance on the first stage. The vehicle is designed to deliver up to 0.47kg of Martian samples to a Mars circular orbit of 380km at 27° inclination. Due to the extremely unique design constraints of this mission, and a recent transition to a Risk Class A posture, the MAV team was compelled to devise unconventional solutions to the vehicle design. The detailed design and analysis of these subsystems and the vehicle as a whole are discussed in this paper relative to all of the engineering disciplines involved.

MAV↗