Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Spinel”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,423 records · Page 79

Microwave-specific heating of crystalline species in nuclear waste glass

Here, the microwave heating of a crystal-free and a partially trevorite-crystallized nuclear waste glass simulant was evaluated. Our results show that a 500-mg monolith of partially crystallized waste glass can be heated from room temperature to above 1600°C within 2 min using a single-mode, highly focused, 2.45 GHz microwave, operating at 300 W. Using X-ray diffraction measurements, we show that trevorite is no longer detectable after irradiation and thermal quenching. When a crystal-free analog of the same waste glass simulant composition was exposed to the same microwave radiation, it could not be heated above 450°C regardless of the heating time. The reduction in crystalline content achieved by selectively heating spinels in the presence of glass suggests that microwave-specific heating should be further explored as a technique for remediating crystal accumulation in a glass melt.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Synthesis of BaTiO[subscript 3]-20wt%CoFe[subscript 2]O[subscript 4] Nanocomposites via Spark Plasma Sintering

Barium titanate-20wt% cobalt ferrite (BaTiO{sub 3}-20wt%CoFe{sub 2}O{sub 4}) nanocomposites were sintered from nanocrystalline BaTiO{sub 3} and CoFe{sub 2}O{sub 4} powders using spark plasma sintering (SPS) and pressureless sintering (PS) techniques. Using SPS, dense polycrystalline composites were obtained at a sintering temperature as low as 860 C and a time of 5 min whereas PS required a higher sintering temperature (1150 C) and time (120 min) to obtain similarly dense composites. Microstructural analysis of the composites showed that both the techniques retained nanocrystalline grain sizes after sintering. High resolution X-ray diffraction measurements revealed that the BaTiO{sub 3}-20wt%CoFe{sub 2}O{sub 4} composites sintered by the SPS technique did not exhibit formation of any new phase(s) due to reaction between the BaTiO{sub 3} and CoFe{sub 2}O{sub 4} phases during sintering. However, the PS technique resulted in the formation of additional phases (other than the BaTiO{sub 3} and CoFe{sub 2}O{sub 4} phases) in the composites. While the composites synthesized by SPS were of superior phase-purity, evidence of Fe diffusion from the spinel to the perovskite phase was found from X-ray diffraction and permittivity measurements.

36 MATERIALS SCIENCE↗

Melting temperature measurement of refractory oxide ceramics as a function of oxygen fugacity using containerless methods

An aerodynamic conical nozzle levitator (CNL) has been used to measure the melting temperatures of refractory ceramics. The well-established method of cooling traces has been adapted to allow measurements for air-sensitive samples using a controlled atmosphere, where the oxygen partial pressure can be adjusted and monitored in real time. In this study, we explain the details of a system that we developed for use at the Spallation Neutron Source (Oak Ridge National Laboratory). Measurements of the melting behavior of (Fe,Cr,Al) 3 O 4 spinels were made between log (PO 2 (atm)) of -0.7 and -5. The melting temperature of hercynite is found to be oxygen potential dependent, ranging between 1692 and 1767°C at log (PO 2 ) values from -4.42 to -0.70.

36 MATERIALS SCIENCE↗

Growth, intermixing, and surface phase formation for zinc tin oxide nanolaminates produced by atomic layer deposition

A broad and expanding range of materials can be produced by atomic layer deposition at relatively low temperatures, including both oxides and metals. For many applications of interest, however, it is desirable to grow more tailored and complex materials such as semiconductors with a certain doping, mixed oxides, and metallic alloys. How well such mixed materials can be accomplished with atomic layer deposition requires knowledge of the conditions under which the resulting films will be mixed, solid solutions, or laminated. The growth and lamination of zinc oxide and tin oxide is studied here by means of the extremely surface sensitive technique of low energy ion scattering, combined with bulk composition and thickness determination, and x-ray diffraction. At the low temperatures used for deposition (150 °C), there is little evidence for atomic scale mixing even with the smallest possible bilayer period, and instead a morphology with small ZnO inclusions in a SnO{sub x} matrix is deduced. Postannealing of such laminates above 400 °C however produces a stable surface phase with a 30% increased density. From the surface stoichiometry, this is likely the inverted spinel of zinc stannate, Zn{sub 2}SnO{sub 4}. Annealing to 800 °C results in films containing crystalline Zn{sub 2}SnO{sub 4}, or multilayered films of crystalline ZnO, Zn{sub 2}SnO{sub 4}, and SnO{sub 2} phases, depending on the bilayer period.

36 MATERIALS SCIENCE↗

Preparation of Exfoliated Graphite Modified with Magnesium Ferrite

A magnetic sorbent based on exfoliated graphite modified with magnesium ferrite has been prepared by impregnating oxidized graphite in a mixed solution of FeCl{sub 3} and Mg(NO{sub 3}){sub 2}, followed by heat treatment of the impregnated oxidized graphite in air. X-ray diffraction and Mössbauer spectroscopy results demonstrate that the structure of the magnesium ferrite is an inverse spinel with a degree of inversion of 0.59. The saturation magnetization of the magnesium ferrite-containing exfoliated graphite is 16.1 emu/g, whereas its oil sorption capacity is as high as 54 g/g. Compaction of the exfoliated graphite to a density of 0.03 g/cm{sup 3} reduced its sorption capacity to 26 g/g. Further increasing the density of the material led to a considerable decrease in its sorption capacity.

36 MATERIALS SCIENCE↗

Synthesis of the Ti{sub 2}AlC MAX Phase with a Reduction Step via Combustion of a TiO{sub 2} + Mg + Al + C Mixture

Technologically viable principles have been developed for the preparation of the MAX phase Ti{sub 2}AlC by self-propagating high-temperature synthesis (SHS) with a reduction step, using titanium dioxide. We have studied the influence of synthesis conditions (starting-mixture composition and ratio of reactants) on the composition, structure, and particle size of Ti{sub 2}AlC powders. The results demonstrate that an excess of magnesium in the starting mixture leads to a decrease in the percentage of MgAl{sub 2}O{sub 4} (spinel), and carbon deficiency in the starting mixture reduces the percentage of titanium carbide in the final product. The Ti{sub 2}AlC powders prepared by SHS consist of agglomerates of layered particles differing in size: from coarse (several microns) to ultrafine and nanometer-sized particles. The composition of the powders was confirmed by chemical analysis, microstructural examination, and X-ray diffraction.

36 MATERIALS SCIENCE↗

Crystal structure of complex natural aluminum magnesium calcium iron oxide

The structure of a new natural oxide found near the Tashelga River (Eastern Siberia) was studied by X-ray diffraction. The pseudo-orthorhombic unit cell parameters are a = 5.6973(1) A, b = 17.1823(4) A, c = 23.5718(5) A, {beta} = 90{sup o}, sp. gr. Pc. The structure was refined to R = 0.0516 based on 4773 reflections with vertical bar F vertical bar > 7{sigma}(F) taking into account the twin plane perpendicular to the z axis (the twin components are 0.47 and 0.53). The crystal-chemical formula (Z = 4) is Ca{sub 2}Mg{sub 2}{sup IV}Fe{sub 2}{sup (2+)IV}[Al{sub 14}{sup VI}O{sub 31}(OH)][Al{sub 2}{sup IV}O][Al{sup IV}]AL{sup IV}(OH)], where the Roman numerals designate the coordination of the atoms. The structure of the mineral is based on wide ribbons of edge-sharing Al octahedra (an integral part of the spinel layer). The ribbons run along the shortest x axis and are inclined to the y and z axes. The adjacent ribbons are shifted with respect to each other along the y axis, resulting in the formation of step-like layers in which the two-ribbon thickness alternates with the three-ribbon thickness. Additional Al octahedra and Mg and Fe{sup 2+} tetrahedra are located between the ribbons. The layers are linked together to form a three-dimensional framework by Al tetrahedra, Ca polyhedra, and hydrogen bonds with the participation of OH groups.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Theory of the formation of the ordered LiZn{sub 0.5}Mn{sub 1.5}O{sub 4} phase

A theory of the structural phase transition in LiZn{sub 0.5}Mn{sub 1.5}O{sub 4} cathode material is proposed. The symmetry of the order parameter, thermodynamics, and mechanisms of formation of the atomic structure of low-symmetry ordered cubic lithium-zinc-manganese oxide spinel have been studied. The critical order parameter inducing the phase transition has been found. It is shown that the calculated LiZn{sub 0.5}Mn{sub 1.5}O{sub 4} structure is formed due to displacements and orderings of lithium, zinc, manganese, and oxygen atoms. Within the Landau theory of phase transitions, it is shown that the phase states may change from high-symmetry cubic disordered Fd3m phase to the low-symmetry ordered cubic P2{sub 1}3 phase as a result of first-order phase transitions.

36 MATERIALS SCIENCE↗

Magnetic resonance in a Cu-Cr-S structure

A layered Cu-Cr-S structure composed of single-crystal CuCrS{sub 2} layers and thin CuCr{sub 2}S{sub 4} plates embedded in them has been investigated by the magnetic resonance and scanning electron microscopy methods. The Curie temperature and saturation magnetization of the spinel phase of the investigated samples have been determined. The thickness of the CuCr{sub 2}S{sub 4} layers has been estimated. The dependence of the growncrystal topology on synthesis conditions has been established. An interpretation of the anomalous behavior of the magnetostatic oscillation intensity is offered.

36 MATERIALS SCIENCE↗

Growth of the (In{sub 2}S{sub 3}){sub x}(FeIn{sub 2}S{sub 4}){sub 1-x} single crystals and properties of photoelectric structures on their basis

Complete mutual solubility in the (In{sub 2}S{sub 3}){sub x}(FeIn{sub 2}S{sub 4}){sub 1-x} system is established. The technology is developed, and single crystals of the continuous series of the (In{sub 2}S{sub 3}){sub x}(FeIn{sub 2}S{sub 4}){sub 1-x} solid solutions are grown for the first time. The linear dependence of the unit cell parameter of single crystals with a cubic spinel lattice on the solid solution composition is found. First, photosensitive Schottky barriers are fabricated, and then, based on studies of their photosensitivity, the character of band-to-band transition is discussed and the values of the band gap depending on the atomic composition are estimated. The possibility of using the obtained solid solutions as broadband photoconverters of optical radiation is revealed.

36 MATERIALS SCIENCE↗

Discovery of the (In{sub 2}S{sub 3}){sub x}(MnIn{sub 2}S{sub 4}){sub 1-x} solid solutions and fabrication of photosensitive structures based on them

A technology of growing single crystals of (In{sub 2}S{sub 3}){sub x}(MnIn{sub 2}S{sub 4}){sub 1-x} solid solutions that provides control over their atomic composition in the entire concentration range 0 {<=} x {<=} 1 is developed. It is shown that, in the range x = 0-1, the single crystals have the cubic spinel structure and the unit cell parameter a follows the linear dependence on x. The exponential character of the temperature dependence of resistivity of solid solutions, on which the first photosensitive Cu/(In{sub 2}S{sub 3})x(MnIn{sub 2}S{sub 4}){sub 1-x} structures are obtained, is revealed. The first photosensitivity spectra of these structures are obtained, and, based on these spectra, dependences of energy of the direct and indirect band-to-band transitions on the composition x are determined. The possibility of applying these structures in broad-band photoconverters of optical radiation is concluded.

36 MATERIALS SCIENCE↗

Quaternary (FeIn{sub 2}S{sub 4}){sub x}(MnIn{sub 2}S{sub 4}){sub 1-x} alloys and photosensitive structures on their basis

Using directional crystallization of the melt of the (FeIn{sub 2}S{sub 4}){sub x}(MnIn{sub 2}S{sub 4}){sub 1-x} alloy, homogeneous crystals of a similar atomic composition are grown over the entire range of compositions 1 {>=} x {>=} 0. It is established that the crystals of the continuous series of quaternary alloys in the range x = 0-1 crystallize in the spinel structure and lattice parameter a linearly depends on x. It is established that it is possible to obtain In(Al)/(FeIn{sub 2}S{sub 4}){sub x}(MnIn{sub 2}S{sub 4}){sub 1-x} photosensitive structures. Room-temperature spectra of relative quantum efficiency of photoconversion of the In(Al)/(FeIn{sub 2}S{sub 4}){sub x}(MnIn{sub 2}S{sub 4}){sub 1-x} structures fabricated for the first time are obtained. From the analysis of these spectra, activation energies of direct and indirect band-to-band transitions for the crystals of the (FeIn{sub 2}S{sub 4}){sub x}(MnIn{sub 2}S{sub 4}){sub 1-x} alloys are determined and the dependence of these parameters on the composition of the position-disordered phases of mentioned alloys is discussed. It is concluded that the crystals of the (FeIn{sub 2}S{sub 4}){sub x}(MnIn{sub 2}S{sub 4}){sub 1-x} alloys can be used in broadband photoconverters of optical radiation.

36 MATERIALS SCIENCE↗

Single crystals of (FeIn{sub 2}S{sub 4}){sub x} · (CuIn{sub 5}S{sub 8}){sub 1–x} alloys: Crystal structure, nuclear gamma resonance spectra, and thermal expansion

FeIn{sub 2}S{sub 4} and CuIn{sub 5}S{sub 8} compounds and (FeIn{sub 2}S{sub 4}){sub x} · (CuIn{sub 5}S{sub 8}){sub 1–x} alloy single crystals are grown by planar crystallization. It is shown that both of the initial FeIn{sub 2}S{sub 4} and CuIn{sub 5}S{sub 8} compounds and alloys on their basis crystallize with the formation of the cubic spinel structure. It is established that the unit-cell parameter a linearly varies with the composition parameter x. By means of nuclear gamma resonance spectroscopy in the transmission mode of measurements, the local states of iron ions in the alloys are studied. For the single crystals grown in the study, thermal expansion is explored using the dilatometry technique, the thermal-expansion coefficients are determined, and the Debye temperature and rms (root-mean-square) dynamic displacements are calculated.

36 MATERIALS SCIENCE↗

Structure, Ferroelectric, and Magnetoelectric Properties of Bulk PZT–NiFe{sub 1.9}Co{sub 0.02}O{sub 4–δ} Composites

The phase composition, microstructure, and dielectric, ferroelectric, magnetic, and magnetoelectric properties of bulk ceramic (1 – x)PZT–xNiFe{sub 1.9}Co{sub 0.02}O{sub 4–δ} composites with 3–0 connectivity have been studied. Using X-ray diffraction and electron microscopy, it has been established that the ferrimagnetic (spinel- like) and ferroelectric (tetragonal perovskite-like) phases separately exist in the composites of all compositions. The simultaneous existence of ferroelectric and ferrimagnetic properties in the composites is confirmed by measuring their P(E) and σ(B) hysteresis loops and studying the temperature dependences of dielectric and magnetic properties. The synthesized composites have high magnetoelectric characteristics: their voltage coefficient at x = 0.4 is 215 mV/A at a frequency of 1 kHz and 130 V/A at an electromechanical resonance frequency of 380 kHz.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Properties of MgFe{sub 2}O{sub 4} Nanoparticles Synthesized by Ultrasonic Aerosol Pyrolysis for Biomedical Applications

We present the data of studies on the structure, phase states, and magnetic properties of magnetic nanoparticles (MNPs) of magnesium ferrite spinel (MgFe{sub 2}O{sub 4}), synthesized by ultrasonic aerosols pyrolysis. Primary single-phase MNPs with an average size of 9.6, 11.5, and 14.0 nm, synthesized from precursors at concentrations of 0.06, 0.12, and 0.24 M, respectively, agglomerate into tightly aggregated spherical particles (secondary particles) with sizes of 206, 300, and 340 nm, respectively. Primary particles inside the spheres do not interact with each other and are in a superparamagnetic state. There is a layer on the surface of the particles, the magnetic structure of which differs from the structure of the inner part of the MNP; this is explained by the formation of a canted spin structure or a spin glass state in the surface layer of the MNPs. MgFe{sub 2}O{sub 4} nanospheres obtained from a precursor at a concentration of 0.06 M are most promising as valid sources of heat in magnetic hyperthermia therapy.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Characterization of oxide scale on Alloy 446 by x-ray nano-beam analysis.

To understand the potential degradation of metallic interconnects, tubes of alloy 446 were exposed to air/hydrogen dual atmosphere at elevated temperatures for 1030 h. The scale developed on the air side consisted of two layers. Because the two sublayers in the oxide scale were too thin for evaluation by regular X-ray diffraction, nanobeam X-ray diffraction was used to study the phase compositions in the scales that formed on both the air and hydrogen sides of alloy 446. The results indicate that Mn{sub 1-x}Cr{sub 2-x}O{sub 4} spinel is the major phase in the oxide scale on alloy 446. The valence of manganese in the oxide scale was also evaluated by X-ray near-edge absorption.

08 HYDROGEN↗

A perspective on coatings to stabilize high-voltage cathodes: LiMn1.5Ni0.5O4 with subnanometer Lipon cycled with LiPF6 electrolyte

High voltage Li-ion cathodes push the limits of stability for both cathode and electrolyte. Here subnanometer coatings of an amorphous thin film electrolyte (Lipon) improved the room temperature and 60 C cycling stability of a LiMn1.5Ni0.5O4 spinel cathode when charged to 4.9V with a standard LiPF6 carbonate electrolyte. The cathodes delivered superior C-rate performances up to a 5C discharge, when compared to the uncoated cathodes. Enhanced performance extended for at least 100 cycles. Electrochemical impedance spectroscopy indicates that Lipon slows the increase of interface resistance. Thicker 1-3nm Lipon coatings are sufficiently insulating as to block electronic transport to the cathode particles. Thick coatings also slow Mn dissolution. Results suggest that Lipon may act to scavenge impurities or block active sites that promote electrolyte decomposition. While greatly improved by the Lipon coating, this cathode is not sufficiently stable for long cycle life applications. Further work is needed to assess if and what surface coatings will ultimately stabilize the high voltage cathodes. Comments include insight from other studies of Lipon coated cathodes and directions for future research.

Li-ion battery↗

Communication—Reactive Sintering of a CoFe 2 O 4 Coating on Ferritic Stainless Steels for SOFC Interconnect Application

A mixed Fe+CoO precursor was successfully utilized to synthesize a dense CoFe 2 O 4 spinel coating on the Crofer 22 APU interconnect via reactive sintering at 900°C for 2 h in air without the use of any reduction treatment. Both the uncoated and coated samples were subject to thermal oxidation at 850°C for 500 h in air. Phase constituents, microstructure, and area specific resistance (ASR) of the uncoated and coated samples before and after the oxidation testing were evaluated. The CoFe 2 O 4 layer effectively reduced the Cr 2 O 3 scale growth and lowered the scale ASR.

25 ENERGY STORAGE↗