Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Solar Development”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,423 records · Page 79
All sourcesNASA NTRSDOE OSTI
NASA NTRS1981

Development of processes for the production of solar grade silicon from halides and alkali metals, phase 1 and phase 2

High temperature reactions of silicon halides with alkali metals for the production of solar grade silicon are described. Product separation and collection processes were evaluated, measure heat release parameters for scaling purposes and effects of reactants and/or products on materials of reactor construction were determined, and preliminary engineering and economic analysis of a scaled up process were made. The feasibility of the basic process to make and collect silicon was demonstrated. The jet impaction/separation process was demonstrated to be a purification process. The rate at which gas phase species from silicon particle precursors, the time required for silane decomposition to produce particles, and the competing rate of growth of silicon seed particles injected into a decomposing silane environment were determined. The extent of silane decomposition as a function of residence time, temperature, and pressure was measured by infrared absorption spectroscopy. A simplistic model is presented to explain the growth of silicon in a decomposing silane enviroment.

Dickson, C. R.↗
NASA NTRS1980

Low cost Czochralski crystal growing technology. Near implementation of the flat plate photovoltaic cost reduction of the low cost solar array project

Equipment developed for the manufacture of over 100 kg of silicon ingot from one crucible by rechanging from another crucible is described. Attempts were made to eliminate the cost of raising the furnace temperature to 250 C above the melting point of silicon by using an RF coil to melt polycrystalline silicon rod as a means of rechanging the crucible. Microprocessor control of the straight growth process was developed and domonstrated for both 4 inch and 6 inch diameter. Both meltdown and melt stabilization processes were achieved using operator prompting through the microprocessor. The use of the RF work coil in poly rod melting as a heat sink in the accelerated growth process was unsuccessful. The total design concept for fabrication and interfacing of the total cold crucible system was completed.

Roberts, E. G.↗
NASA NTRS1983

Development of metallization process

Solar cells were produced using a Mo/Sn/TiH screen printed paste with a lead/borosilicate frit that are electrically comparable to control silver cells. The process is currently unsuccessful because the soldering of interconnects to these cells has proved difficult. Future work will investigate using CO instead of H2 as the reducing gas and putting an ITO coating on the cell prior to metallization.

Garcia, A., III↗
NASA NTRS1983

Development of a computational model for predicting solar wind flows past nonmagnetic terrestrial planets

A computational model for the determination of the detailed plasma and magnetic field properties of the global interaction of the solar wind with nonmagnetic terrestrial planetary obstacles is described. The theoretical method is based on an established single fluid, steady, dissipationless, magnetohydrodynamic continuum model, and is appropriate for the calculation of supersonic, super-Alfvenic solar wind flow past terrestrial ionospheres.

Stahara, S. S.↗
NASA NTRS1984

The flow of plasma in the solar terrestrial environment

The development of electric fields in an expanding plasma was studied. With regard to the polar wind, it was found that hot magnetospheric electrons have a pronounced effect on the polar wind. In addition, there is no O(+) charge exchange barrier and substantial fluxes of O(+) ions can escape with the polar wind. In the auroral plasma physics area, the excitation of electrostatic waves by field aligned auroral electron beams was examined. It was demonstrated that the auroral field aligned current density can be large enough to excite Buneman double layers. For situations that lead to strong double layers, it was shown that the temporal evolution of the potential profile is controlled by current fluctuations. Two dimensional particle in cell simulations were conducted, and the high frequency wave turbulence excited by an auroral electron beam of finite width perpendicular to an ambient magnetic field was investigated. The formation of V shaped auroral potential structures was studied, and numerical simulations of double layers and auroral electric fields were reviewed.

Schunk, R. W.↗
NASA NTRS1984

Advanced module development overview

Crystalline silicon solar power modules are examined for reliability and cost effectiveness. A goal of 12% solar energy conversion efficiency is considered feasible at a cost of 12/kWh, and a decision is made to limit consideration to float zone silicon wafer and dendritic web silicone modules. A preliminary module packaging configuration of glass/ethylene vinyl acetate/plastic film is selected. Anticipated module efficiency levels are 12.6% at 25 C and 11.5% at NOCT (Nominal Operating Cell Temperature).

Smokler, M. I.↗
NASA NTRS1984

The new space transportation system and the Solar Maximum Repair Mission

A development history, program management and performance capability assessment account is presented for the NASA Solar Maximum Repair Mission conducted by the Space Shuttle Orbiter, which incorporated extravehicular activity as an integral part of servicing efforts. It was determined soon after assessment of the Solar Maximum Mission satellite's hardware malfunction that such a repair mission could be undertaken by the Orbiter at substantially lower cost than the construction and launch of a comparable new spacecraft. A photographic account is given of the various stages of the Shuttle Orbiter-based repair procedure.

Turner, D. N.↗
NASA NTRS1987

Development of optical modulators for measurements of solar magnetic fields

The measurement of polarized light allows solar astronomers to infer the magnetic field on the Sun. The accuracy of these measurements is dependent on the stable retardation characteristics of the polarization modulators used to minimize the atmospheric effects seen in ground-based observations. This report describes the work by the Space Science Laboratory at Marshall Space Flight Center to improve two types of polarization modulators. As a result, the timing characteristics for both electrooptic crystals (KD*Ps) and liquid crystal devices (LCDs) have been studied and will be used to enhance the capabilities of the MSFC Vector Magnetograph.

West, E. A.↗
NASA NTRS1987

High power CW iodine laser pumped by solar simulator

An iodine photodissociation laser was pumped by a long Ar arc as the solar simulator to produce a 10-W CW output. Continuous lasing for 1 h was achieved with a flow of the laser material n-C3F7I. The 10-W CW output is the highest produced to date and establishes the feasibility of developing a solar-pumped laser for space power transmission.

Lee, Ja H.↗
NASA NTRS1993

Momentum accumulation due to solar radiation torque, and reaction wheel sizing, with configuration optimization

This paper has a two-fold objective: determination of yearly momentum accumulation due to solar radiation pressure, and optimum reaction wheel sizing. The first objective is confronted while determining propellant consumption by the attitude control system over a spacecraft's lifetime. This, however, cannot be obtained from the daily momentum accumulation and treating that constant throughout the year, because the orientation of the solar arrays relative to the spacecraft changes over a wide range in a year, particularly if the spacecraft has two arrays, one normal and the other off-normal to different extent at different times to the sun rays. The paper first develops commands for the arrays for tracking the sun, the arrays articulated to earth-pointing spacecraft with two rotational degrees of freedom, and spacecraft in an arbitrary circular orbit. After developing expressions for solar radiation torque due to one or both arrays, arranged symmetrically or asymmetrically relative to the spacecraft bus, momentum accumulation over an orbit and then over a year are determined. The remainder of the paper is concerned with designing reaction wheel configurations. Four-, six-, and three-wheel configurations are considered, and for given torque and momentum requirements, their cant angles with the roll/yaw plane are optimized for minimum power consumption. Finally, their momentum and torque capacities are determined for one-wheel failure scenario, and six configurations are compared and contrasted.

Hablani, Hari B.↗
NASA NTRS1991

Advanced design for orbital debris removal in support of solar system exploration

The development of an Autonomous Space Processor for Orbital Debris (ASPOD) is the ultimate goal. The craft will process, in situ, orbital debris using resources available in low Earth orbit (LEO). The serious problem of orbital debris is briefly described and the nature of the large debris population is outlined. This year, focus was on development of a versatile robotic manipulator to augment an existing robotic arm; incorporation of remote operation of robotic arms; and formulation of optimal (time and energy) trajectory planning algorithms for coordinating robotic arms. The mechanical design of the new arm is described in detail. The versatile work envelope is explained showing the flexibility of the new design. Several telemetry communication systems are described which will enable the remote operation of the robotic arms. The trajectory planning algorithms are fully developed for both the time-optimal and energy-optimal problem. The optimal problem is solved using phase plane techniques while the energy optimal problem is solved using dynamics programming.

Source record↗
NASA NTRS1979

Develop Silicone Encapsulation Systems for Terrestrial Silicon Solar Arrays

This work resulted in two basic accomplishments.The first was the identification of DOW CORNING Q1-2577 as a suitable encapsulation material for use in a cost effective encapsulation system. The second was the preparation of a silicon-acrylic cover material containing a durable ultraviolet screening agent for the protection of photo-oxidatively sensitive polymers.

Source record↗
NASA NTRS2006

Rapid Development of Gossamer Propulsion for NASA Inner Solar System Science Missions

Over a two and one-half year period dating from 2003 through 2005, NASA s In-Space Propulsion Program matured solar sail technology from laboratory components to full systems, demonstrated in as relevant a space environment as could feasibly be simulated on the ground. This paper describes the challenges identified; as well as the approaches taken toward solving a broad set of issues spanning material science, manufacturing technology, and interplanetary trajectory optimization. Revolutionary advances in system structural predictive analysis and characterization testing occurred. Also addressed are the remaining technology challenges that might be resolved with further ground technology research, geared toward reducing technical risks associated with future space validation and science missions.

Young, Roy M.↗
NASA NTRS2013

PV Reliability Development Lessons from JPL's Flat Plate Solar Array Project

Key reliability and engineering lessons learned from the 20-year history of the Jet Propulsion Laboratory's Flat-Plate Solar Array Project and thin film module reliability research activities are presented and analyzed. Particular emphasis is placed on lessons applicable to evolving new module technologies and the organizations involved with these technologies. The user-specific demand for reliability is a strong function of the application, its location, and its expected duration. Lessons relative to effective means of specifying reliability are described, and commonly used test requirements are assessed from the standpoint of which are the most troublesome to pass, and which correlate best with field experience. Module design lessons are also summarized, including the significance of the most frequently encountered failure mechanisms and the role of encapsulate and cell reliability in determining module reliability. Lessons pertaining to research, design, and test approaches include the historical role and usefulness of qualification tests and field tests.

photovoltaics↗
NASA NTRS2012

Large-Amplitude Longitudinal Oscillations in a Solar Filament

We have developed the first self-consistent model for the observed large-amplitude oscillations along filament axes that explains the restoring force and damping mechanism. We have investigated the oscillations of multiple threads formed in long, dipped flux tubes through the thermal nonequilibrium process, and found that the oscillation properties predicted by our simulations agree with the observed behavior. We then constructed a model for the large-amplitude longitudinal oscillations that demonstrates that the restoring force is the projected gravity in the tube where the threads oscillate. Although the period is independent of the tube length and the constantly growing mass, the motions are strongly damped by the steady accretion of mass onto the threads by thermal nonequilibrium. The observations and our model suggest that a nearby impulsive event drives the existing prominence threads along their supporting tubes, away from the heating deposition site, without destroying them. The subsequent oscillations occur because the displaced threads reside in magnetic concavities with large radii of curvature. Our model yields a powerful seismological method for constraining the coronal magnetic field and radius of curvature of dips. Furthermore, these results indicate that the magnetic structure is most consistent with the sheared-arcade model for filament channels.

lament axes↗
NASA NTRS2016

An Assessment of New Satellite Data Products for the Development of a Long-Term Global Solar Resource at 10-100 km

A project representing an effort to reprocess the NASA based solar resource data sets is reviewed. The effort represented a collaboration between NASA, NOAA, NREL and the SUNY-Albany and aimed to deliver a 10 km resolution, 3-hourly data set spanning from 1983 through near-present. Part of the project was to transition project capability to NREL for annual processing to extend data set. Due to delays in the key input project called ISCCP, we evaluate only Beta versions of this data set and also introduce the potential use of another NASA Langley based cloud data set for the CERES project. The CERES project uses these cloud properties to compute global top-of-atmosphere and surface fluxes at the 1x1 degree resolution. Here, we also briefly discuss these data sets in potential usage for solar resource benchmarking.

Stackhouse, Paul W., Jr.↗