Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Segregation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,423 records · Page 79

A review of irradiation effects on LWR core internal materials - IASCC susceptibility and crack growth rates of austenitic stainless steels.

Austenitic stainless steels (SSs) are used extensively as structural alloys in the internal components of light water reactor (LWR) pressure vessels because of their relatively high strength, ductility, and fracture toughness. However, exposure to neutron irradiation for extended periods changes the microstructure (radiation hardening) and microchemistry (radiation-induced segregation) of these steels, and degrades their fracture properties. Irradiation-assisted stress corrosion cracking (IASCC) is another degradation process that affects LWR internal components exposed to neutron radiation. The existing data on irradiated austenitic SSs were reviewed to evaluate the effects of key parameters such as material composition, irradiation dose, and water chemistry on IASCC susceptibility and crack growth rates of these materials in LWR environments. The significance of microstructural and microchemistry changes in the material on IASCC susceptibility is also discussed. The results are used to determine (a) the threshold fluence for IASCC and (b) the disposition curves for cyclic and IASCC growth rates for irradiated SSs in LWR environments.

36 MATERIALS SCIENCE↗

Atom probe tomography characterization of neutron irradiated surveillance samples from the R. E. Ginna reactor pressure vessel

Surveillance samples of a low copper (nominally 0.05 wt.% Cu) forging and a higher copper (0.23 wt.% Cu) submerged arc weld from the R. E. Ginna reactor pressure vessel have been characterized by atom probe tomography (APT) after exposure to three levels of neutron irradiation, i.e., fluences of 1.7, 3.6 and 5.8 × 10 23 n.m –2 (E > 1 MeV), and inlet temperatures of ~289 °C (~552 °F). As no copper-enriched precipitates were observed in the low copper forging, and the measured copper content in the ferrite matrix was 0.04± <0.01 at.% Cu, after neutron irradiation to a fluence of 1.7 × 10 23 n.m –3 , this copper level was below the solubility limit. A number density of 2 × 10 22 m –3 of Ni–, Mn– Si-enriched precipitates with an equivalent radius of gyration of 1.7 ± 0.4 nm were detected in the sample. However, Cu-, Ni-, Mn-enriched precipitates were observed in specimens cut from different surveillance specimens from the same forging material in which the overall measured copper level was 0.08± <0.01 at.% (fluence of 3.6 × 10 23 n.m –3 ) and 0.09± <0.01 at.% Cu (fluence of 5.8 × 10 23 n.m –3 ). Therefore, these slightly higher copper contents were above the solubility limit of Cu under these irradiation conditions. A best fit of all the composition data indicated that the size and number density of the Cu-enriched precipitates increased slightly in both size and number density by additional exposure to neutron irradiation. High number densities of Cu-enriched precipitates were observed in the higher Cu submerged arc weld for all irradiated conditions. The size and number density of the precipitates in the welds were higher than in the same fluence forgings. Some Cu-enriched precipitates were found to have Ni-, Mn- Si-, and P-enriched regions on their surfaces suggesting a preferential nucleation site. Furthermore, atom maps revealed P, Ni, and Mn segregation to, and preferential precipitation of, Cu-enriched precipitates over the surface of a grain boundary in the low fluence weld.

36 MATERIALS SCIENCE↗

Heavy ion irradiation response of an additively manufactured 316LN stainless steel

Additive manufacturing has become an appealing technique to fabricate three-dimensional metallic materials and components for nuclear reactors. However, response of additively manufactured alloys to high-dose heavy ion irradiations at elevated temperatures is still not well understood. Here, an additively manufactured 316LN austenitic stainless steel with high-density solidification cells was irradiated using 3.5 MeV Fe ion to a peak dose of 220 dpa at 450 °C. Microscopy studies show a lower Frank loop density and smaller size in the additively manufactured sample compared with its cold worked counterpart, and the cellular structures may largely suppress the formation of perfect loops and dislocation networks and reduce the magnitude of solute segregations comparing with high angle grain boundaries. In conclusion, the present work advances the understanding on the high-temperature irradiation response of additively manufactured steels for nuclear reactor applications.

36 MATERIALS SCIENCE↗

Mixed conductivity, oxygen permeability and redox behavior of K{sub 2}NiF{sub 4}-type La{sub 2}Ni{sub 0.9}Fe{sub 0.1}O{sub 4+{delta}}

The total conductivity and Seebeck coefficient of La{sub 2}Ni{sub 0.9}Fe{sub 0.1}O{sub 4+{delta}} with K{sub 2}NiF{sub 4}-type structure, studied in the oxygen partial pressure range from 10{sup -5} to 0.5 atm at 973-1223 K, were analyzed in combination with the steady-state oxygen permeability, oxygen non-stoichiometry and Moessbauer spectroscopy data in order to examine the electronic and ionic transport mechanisms. Doping of La{sub 2}NiO{sub 4+{delta}} with iron was found to promote hole localization on nickel cations due to the formation of stable Fe{sup 3+} states, although the electrical properties dominated by p-type electronic conduction under oxidizing conditions exhibit trends typical for both itinerant and localized behavior of the electronic sublattice. The segregation of metallic Ni on reduction, which occurs at oxygen chemical potentials close to the low-p(O{sub 2}) stability boundary of undoped lanthanum nickelate, is responsible for the high catalytic activity towards partial oxidation of methane by the lattice oxygen of La{sub 2}Ni{sub 0.9}Fe{sub 0.1}O{sub 4+{delta}} as revealed by thermogravimetry and temperature-programmed reduction in dry CH{sub 4}-He flow at 573-1173 K. A model for the oxygen permeation fluxes through dense La{sub 2}Ni{sub 0.9}Fe{sub 0.1}O{sub 4+{delta}} ceramics, limited by both bulk ionic conduction and surface exchange kinetics, was proposed and validated. - Graphical abstract: Oxygen permeation fluxes through iron-doped lanthanum nickelate ceramics.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

La{sup 3+} doping of the Sr{sub 2}CoWO{sub 6} double perovskite: A structural and magnetic study

La-doped Sr{sub 2}CoWO{sub 6} double perovskites have been prepared in air in polycrystalline form by solid-state reaction. These materials have been studied by X-ray powder diffraction (XRPD), neutron powder diffraction (NPD) and magnetic susceptibility. The structural refinement was performed from combined XRPD and NPD data (D2B instrument, {lambda}=1.594 A). At room temperature, the replacement of Sr{sup 2+} by La{sup 3+} induces a change of the tetragonal structure, space group I4/m of the undoped Sr{sub 2}CoWO{sub 6} into the distorted monoclinic crystal structure, space group P2{sub 1}/n, Z=2. The structure of La-doped phases contains alternating CoO{sub 6} and (Co/W)O{sub 6} octahedra, almost fully ordered. On the other hand, the replacement of Sr{sup 2+} by La{sup 3+} induces a partial replacement of W{sup 6+} by Co{sup 2+} into the B sites, i.e. Sr{sub 2-x}La{sub x}CoW{sub 1-y}Co{sub y}O{sub 6} (y=x/4) with segregation of SrWO{sub 4}. Magnetic and neutron diffraction measurements indicate an antiferromagnetic ordering below T{sub N}=24 K independently of the La-substitution. - Graphical abstract: La-doped Sr{sub 2}CoWO{sub 6} double perovskites have been prepared in polycrystalline form by solid-state reaction. The general formula of these compounds is Sr{sub 2-x}La{sub x}CoW{sub 1-y}Co{sub y}O{sub 6} (y=x/4). XRPD, NPD and magnetic susceptibility studies were performed. The structure of monoclinic La-doped phases contains alternating CoO{sub 6} and (Co/W)O{sub 6} octahedra, almost fully ordered. NPD and magnetic measurements indicate an antiferromagnetic ordering at low temperature.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

High temperature phase transition in SOFC anodes based on Sr{sub 2}MgMoO{sub 6-{delta}}

The double perovskite Sr{sub 2}MgMoO{sub 6-{delta}} has been recently reported as an efficient anode material for solid oxide fuel cells (SOFCs). In the present work, this material have been investigated by high temperature X-ray diffraction (XRD), differential scanning calorimetry (DSC) and impedance spectroscopy to further characterise its properties as SOFC anode. DSC and XRD measurements indicate that Sr{sub 2}MgMoO{sub 6-{delta}} exhibits a reversible phase transition around 275 deg. C from triclinic (I1-bar) with an octahedral tilting distortion to cubic (Fm3-barm) without octahedral distortion. This phase transition is continuous with increasing temperature without any sudden cell volume change during the phase transformation. The main effect of the phase transformation is observed in the electrical conductivity with a change in the activation energy at low temperature. La{sup 3+} and Fe-substituted Sr{sub 2}MgMoO{sub 6-{delta}} phases were also investigated, however these materials are unstable under oxidising conditions due to phase segregations above 600 deg. C. - Graphical abstract: The double perovskite Sr{sub 2}MgMoO{sub 6}, recently proposed as an efficient SOFC anode for direct hydrocarbon oxidation, exhibits a reversible structural phase transition from triclinic to cubic at 275 deg. C.

36 MATERIALS SCIENCE↗

Microstructure of the spray formed Vanadis 4 steel and its ultrafine structure

The as-sprayed microstructure of the Vanadis 4 steel was studied. It was observed that the as-sprayed microstructure consists of martensite, retained austenite and uniformly distributed spheroidal carbides. The Kurdiumov-Sachs crystallographic relation between martensite and retained austenite is confirmed by transmission electron microscope. No macro segregation or network carbides are found. This can be explained in terms of the rapid solidification of spray forming for microstructure refining. The steel obtained by the new processing has a uniform carbide distribution, and the average carbide size is even smaller than the equivalent in the powder metallurgical Vanadis 4 steel. It was proved that spray forming can be considered as a new and high-efficient way to replace powder metallurgy for the production of Vanadis 4 steel.

36 MATERIALS SCIENCE↗

Purification of Cu by hydrogen plasma-arc zone melting and characterization of trace impurities by secondary ion mass spectrometry

Purification of 4N (99.99%) and 6N (99.9999%) purity Cu rods by hydrogen plasma-arc zone melting was carried out. Weight loss in the 4N and 6N Cu rods as a function of number of zone refined passes revealed a higher rate of impurity removal by vaporization in 4N Cu when compared to 6N Cu. Purification effect was studied by analyzing major impurities like Mg, Si, Ca, Ti, Cr, Ni and Fe by O{sub 2}{sup +} ions and C, O, As, Cl, P and S by Cs{sup +} ion sources using secondary ion mass spectrometry. A remarkable decrease of Si, Ti and Fe impurity concentrations in Cu at x/L = 0.03 after 10 zone passes was observed, but no similar purification effect along the remaining length of the zone refined copper rod was observed. Mg, Se and Ca in the Cu rods were reduced faster by a high evaporation effect due to P{sub i}/P{sub Cu} > 10{sup 2}. On the other hand, removal of O, C, S and Se was expectedly dominated by vaporization in the form of H{sub 2}O, CH{sub 4,} H{sub 2}S, and H{sub 2}Se through thermodynamically favored reactions. The overall segregation rate of the individual impurity elements was decreased with an increase in the purity from 4N to 6N of Cu rods. SIMS analysis of trace impurities was successfully carried out on HPZM Cu for quantitative estimation.

36 MATERIALS SCIENCE↗

Sr effect on the microstructure and tensile properties of A357 aluminum alloy and Al{sub 2}O{sub 3}/SiC-A357 cast composites

The effect of strontium as a modifier on the microstructures and tensile properties of two castable particulate metal matrix composites has been studied. The particulate metal matrix composites had similar matrix alloy (A357) but different reinforcing fine particles (silicon carbide and alumina). Results showed that the addition of 0.03% strontium makes a modest improvement to the yield strength, ultimate tensile strength and elongation percentage values, and the scatter of these properties, but makes a significant improvement to minimum strength and elongation results. Microstructural examinations by scanning electron microscope and energy dispersive spectroscopy analysis of metal matrix composites showed segregation of strontium on both the silicon carbide and alumina particles. Further results showed that the addition of higher strontium levels contributes to the over-modification of the eutectic silicon and promotes the formation of an Al-Si-Sr intermetallic compound on the particle/matrix interface.

36 MATERIALS SCIENCE↗

Study of hot tearing of A206 aluminum alloy using Instrumented Constrained T-shaped Casting method

The hot tearing susceptibility of A206 aluminum alloy was investigated using Instrumented Constrained T-shaped Casting method and the effect of the casting temperature on hot tearing was studied. The Instrumented Constrained T-shaped Casting apparatus enabled real-time measurements of the contraction load developed in the casting and the temperature variations during solidification as a function of time. Critical temperatures and points during solidification of the castings were extracted from these data. The contraction load developed at the coalescence point of the castings was identified as a comparative criterion for predicting the hot tearing susceptibility of the alloys which could be utilized even when no visual tearing had occurred. The results showed that hot tearing susceptibility increased with the casting temperature. This was associated with reduced cooling rate, increased solute segregation and more localized hot spot formation at the T-junction area. Increase in the casting temperature also increased the grain size which may in turn have affected the initiation of the hot tears. The visual observations were further validated with radiographic tests.

36 MATERIALS SCIENCE↗

Investigation on microstructure characterization and property of rapidly solidified Mg-Zn-Ca-Ce-La alloys

Rapidly solidified (RS) Mg-Zn-Ca-Ce-La (wt.%) alloys have been produced via atomizing the alloy melt and subsequent splat-quenching on the water-cooled copper twin-rollers in the form of flakes. Microstructure characterization, phase compositions and thermal stability of the alloys have been systematically investigated. The results showed that with addition of RE (Ce and La) to the Mg-6Zn-5Ca alloy, the stable intermetallic compounds i.e. the Mg{sub x}Zn{sub y}RE{sub z} phase with a few Ca (about 3 at.%), shortened as the T Prime phase, were formed at the expense of the binary Mg-Zn and Ca{sub 2}Mg{sub 6}Zn{sub 3} phases, which was possibly beneficial to the enhanced thermal stability of the alloy. In the Mg-6Zn-5Ca-3Ce-0.5La alloy, the composition of the T Prime phase in the grain interior was different from that at the grain boundaries, in which the segregation of the La elements was found, and the atomic percentage ratio of Zn to Ce in the T Prime phase within the grains was close to 2. Moreover, the stable Mg{sub 2}Ca phases were detected around the T Prime phases at the grain boundaries in the alloy. - Research Highlights: Black-Right-Pointing-Pointer The phase constitution of RS Mg-6Zn-5Ca alloy can be improved by RE additions. Black-Right-Pointing-Pointer In the Mg-Zn-Ca-Ce-La alloys, the Mg{sub x}Zn{sub y}RE{sub z} phase with a few Ca (T Prime phase) is formed. Black-Right-Pointing-Pointer The formation of the T Prime phase leads to the loss of the Mg-Zn and Ca{sub 2}Mg{sub 6}Zn{sub 3} phases. Black-Right-Pointing-Pointer The composition of the T Prime phase differs from the grain interior to the grain boundary.

36 MATERIALS SCIENCE↗

Increasing Ti-6Al-4V brazed joint strength equal to the base metal by Ti and Zr amorphous filler alloys

Microstructural features developed along with mechanical properties in furnace brazing of Ti-6Al-4V alloy using STEMET 1228 (Ti-26.8Zr-13Ni-13.9Cu, wt.%) and STEMET 1406 (Zr-9.7Ti-12.4Ni-11.2Cu, wt.%) amorphous filler alloys. Brazing temperatures employed were 900-950 Degree-Sign C for the titanium-based filler and 900-990 Degree-Sign C for the zirconium-based filler alloys, respectively. The brazing time durations were 600, 1200 and 1800 s. The brazed joints were evaluated by ultrasonic test, and their microstructures and phase constitutions analyzed by metallography, scanning electron microscopy and X-ray diffraction analysis. Since microstructural evolution across the furnace brazed joints primarily depends on their alloying elements such as Cu, Ni and Zr along the joint. Accordingly, existence of Zr{sub 2}Cu, Ti{sub 2}Cu and (Ti,Zr){sub 2}Ni intermetallic compounds was identified in the brazed joints. The chemical composition of segregation region in the center of brazed joints was identical to virgin filler alloy content which greatly deteriorated the shear strength of the joints. Adequate brazing time (1800 s) and/or temperature (950 Degree-Sign C for Ti-based and 990 Degree-Sign C for Zr-based) resulted in an acicular Widmanstaetten microstructure throughout the entire joint section due to eutectoid reaction. This microstructure increased the shear strength of the brazed joints up to the Ti-6Al-4V tensile strength level. Consequently, Ti-6Al-4V can be furnace brazed by Ti and Zr base foils produced excellent joint strengths. - Highlights: Black-Right-Pointing-Pointer Temperature or time was the main factors of controlling braze joint strength. Black-Right-Pointing-Pointer Developing a Widmanstaetten microstructure generates equal strength to base metal. Black-Right-Pointing-Pointer Brittle intermetallic compounds like (Ti,Zr){sub 2}Ni/Cu deteriorate shear strength. Black-Right-Pointing-Pointer Ti and Zr base filler alloys were the best choice for brazing Ti-6Al-4V.

36 MATERIALS SCIENCE↗

Solidification characterization of a new rapidly solidified Ni-Cr-Co based superalloy

The solidification characterization of a new rapidly solidified Ni-Cr-Co based superalloy prepared by plasma rotating electrode process was investigated by means of optical microscope, scanning electron microscope, and transmission electron microscope. The results show that the solidification microstructure changes from dendrites to cellular and microcrystal structures with decreasing powder size. The elements of Co, Cr, W and Ni are enriched in the dendrites, while Mo, Nb and Ti are higher in the interdendritic regions. The relationships between powder size with the average solid-liquid interface moving rate, the average interface temperature gradient and the average cooling rate are established. Microsegregation is increased with larger powder size. The geometric integrity of MC Prime type carbides in the powders changes from regular to diverse with decreasing powder size. The morphology and quantity of carbides depend on the thermal parameters and non-equilibrium solute partition coefficients during rapid solidification. - Highlights: Black-Right-Pointing-Pointer The relations of solidification thermal parameters with powder size are established. Black-Right-Pointing-Pointer The relation of non-equilibrium solute partition with powder size is investigated. Black-Right-Pointing-Pointer The solidification microstructure is related to thermal parameters. Black-Right-Pointing-Pointer The segregation behavior is linked to non-equilibrium partition coefficients. Black-Right-Pointing-Pointer The morphology and quantity of carbides depend on the above combined factors.

36 MATERIALS SCIENCE↗

Li-atoms-induced structure changes of Guinier–Preston–Bagaryatsky zones in AlCuLiMg alloys

Guinier–Preston–Bagaryatsky (GPB) zones are the well-known strengthening precipitates of AlCuMg alloys formed upon thermal ageing. Here we report that when formed in AlCuLiMg alloys the GPB zones can change significantly in morphology and structure. It is shown that though they do still consist of Al, Cu and Mg elements fundamentally, the GPB zones in AlCuLiMg alloys have a rather different structure due to a featured Li-segregation at their interfaces with the matrix and possible Li-replacement of partial Mg atoms in the structure. As such the Li-containing GPB zones often develop from one-dimensional to quasi-two-dimensional precipitates. - Highlights: • We observe Guinier–Preston–Bagaryatsky zone variants in AlCuLiMg alloys. • We obtain atomic-resolution images of the precipitates and model their structures. • Li-atoms play a key role in modifying the structure of these precipitate variants.

36 MATERIALS SCIENCE↗

Atomic scale characterization of white etching area and its adjacent matrix in a martensitic 100Cr6 bearing steel

Atom probe tomography was employed to characterize the microstructure and C distribution in the white etching area (WEA) of a martensitic 100Cr6 bearing steel subjected to rolling contact fatigue. Different from its surrounding matrix where a plate-like martensitic structure prevails, the WEA exhibits equiaxed grains with a uniform grain size of about 10 nm. Significant C grain boundary enrichment (>7.5at.%) and an overall higher C concentration than the nominal value are observed in the WEA. These results suggest that the formation of WEA results from severe local plastic deformation that causes dissolution of carbides and the redistribution of C. - Highlights: •APT has been applied to characterize the microstructure of white etching area (WEA). •Quantitative analyses of C distribution indicate that carbides are dissolved on the WEA. •WEA contains equiaxed grains with a uniform grain size of 10 nm. •C segregation at grain boundaries stabilizes the nanosized grain structure. •Formation of WEA is explained by severe local plastic deformation introduced by cyclic contact loading.

36 MATERIALS SCIENCE↗

Characterization of thin films prepared by co-sputtering iron and titanium precursors and thermal oxidation under air atmosphere

Highlights: • Thin films of mixed iron and titanium oxide were prepared by Ti-Fe annealing. • Segregation and phase separation of iron and titanium oxides are observed. • Formation of iron rich (Fe{sub x}O) nanoparticles at the surface region is revealed. • Formation of thin films with high refractive index can be obtained. - Abstract: Nanocomposites of metal oxides are useful materials for operation in many energy conversion systems. In this study, such nanocomposites were prepared by oxidation of mixtures of iron and titanium precursor metallic thin films at 520 °C under air atmosphere. The metallic films with different iron percentages were obtained by radio frequency (RF) magnetron sputtering on glass and silicon substrates. The films were characterized by means of X-ray Diffraction (XRD), Raman spectroscopy, UV–Vis spectroscopy, High Resolution Scanning Transmission Electron Microscopy (HRSTEM), Ellipsometry and X-ray Photo-electron Spectroscopy (XPS). The results show that these films present mainly two nanometric phases, namely Fe{sub 2}O{sub 3} and TiO{sub 2}. A phase separation was observed; the film surface was found to be iron rich oxide or clusters of iron rich oxide (Fe{sub x}O{sub y}, x > y), whereas titanium accumulated deeply in the bulk, forming TiO{sub 2} far below the film surface. A red shift of optical absorption as well as a relatively stable high refractive index (varying between 3.1 and 3.5) over a broad band of optical frequencies was observed for the films containing higher iron initial concentrations.

36 MATERIALS SCIENCE↗