SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Motor tone predictions using a vibration analysis and input from design parameters for high power density motors show that the noise can be significantly higher or lower than the empirical correlations and exceeds the stated uncertainty.
Boundary Layer Ingestion (BLI) for aircraft applications was first proposed by Apollo Smith and Howard Roberts in a 1947 paper that studied the use of jet intakes embedded in the boundary layer as a means to maintain laminar flow and reduce aircraft drag. While the use of BLI in aviation didn't catch on it was heavily studied and utilized for marine applications. In 1993 interest in BLI applications to aircraft design was renewed when Leyroy Smith published novel work using a boundary layer analysis combined with basic propulsion modeling to show the potential for significant fuel burn reduction. Smith identified the tightly coupled aero-propulsive nature of BLI as a key challenge in the analysis and design of the concept.
In this paper we present ion thruster design concepts created using the new computer codes that model performance limiting and erosion mechanisms. Presently, the codes model extraction grid ion optics and both discharge and neutralizer hollow cathodes.
In support of the Exploration Vision for returning to the Moon and beyond, NASA and its partners are developing and testing critical cryogenic fluid propellant technologies that will meet the need for high performance propellants on long-term missions. Reliable knowledge of low-gravity cryogenic fluid management behavior is lacking and yet is critical in the areas of tank thermal and pressure control, fluid acquisition, mass gauging, and fluid transfer. Such knowledge can significantly reduce or even eliminate tank fluid boil-off losses for long term missions, reduce propellant launch mass and required on-orbit margins, and simplify vehicle operations. The Propulsion and Cryogenic Advanced Development (PCAD) Project is performing experimental and analytical evaluation of several areas within Cryogenic Fluid Management (CFM) to enable NASA's Exploration Vision. This paper discusses the status of the PCAD CFM technology focus areas relative to the anticipated CFM requirements to enable execution of the Vision for Space Exploration.
The benefits and costs associated with placing large space systems (LSS) in operational orbits were investigated, and a flexible computer model for analyzing these benefits and costs was developed. A mission model for LSS was identified that included both NASA/Commercial and DOD missions. This model included a total of 68 STS launches for the NASA/Commercial missions and 202 launches for the DOD missions. The mission catalog was of sufficient depth to define the structure type, mass and acceleration limits of each LSS. Conceptual primary propulsion stages (PPS) designs for orbital transfer were developed for three low thrust LO2/LH2 engines baselined for the study. The performance characteristics for each of these PPS was compared to the LSS mission catalog to create a mission capture. The costs involved in placing the LSS in their operational orbits were identified. The two primary costs were that of the PPS and of the STS launch. The cost of the LSS was not included as it is not a function of the PPS performance. The basic relationships and algorithms that could be used to describe the costs were established. The benefit criteria for the mission model were also defined. These included mission capture, reliability, technical risk, development time, and growth potential. Rating guidelines were established for each parameter. For flexibility, each parameter is assigned a weighting factor.
An assessment of model uncertainty via probabilistic methods is described. An important question that arises in conceptual design is how accurate do models have to be to be useful? That is to say, when do other uncertainties in higher fidelity model counteract its accuracy when compared to a lower fidelity model faced with these same uncertainties?.
Magneto-inertial fusion concepts often use a pulsed high current discharge in a cylindrical coil to generate a rapidly changing axial magnetic field, inducing a counter-propagating current in the conducting outer liner of a centrally aligned cylindrical fusion target. The Lorentz force arising from the axial field and azimuthal liner current rapidly implodes the target radially inward, compressing the fuel to reach fusion conditions.
A series of Mach 5 to 7 freejet tests of a Rocket Based Combined Cycle (RBCC) engine were cnducted at the NASA Lewis Research Center (LERC) Hypersonic Tunnel Facility (HTF). This paper describes the configuration and operation of the HTF and the RBCC engine during these tests. A number of facility support systems are described which were added or modified to enhance the HTF test capability for conducting this experiment. The unfueled aerodynamic perfor- mance of the RBCC engine flowpath is also presented and compared to sub-scale test results previously obtained in the NASA LERC I x I Supersonic Wind Tunnel (SWT) and to Computational Fluid Dynamic (CFD) analysis results. This test program demonstrated a successful configuration of the HTF for facility starting and operation with a generic RBCC type engine and an increased range of facility operating conditions. The ability of sub-scale testing and CFD analysis to predict flowpath performance was also shown. The HTF is a freejet, blowdown propulsion test facility that can simulate up to Mach 7 flight conditions with true air composition. Mach 5, 6, and 7 facility nozzles are available, each with an exit diameter of 42 in. This combination of clean air, large scale, and Mach 7 capabilities is unique to the HTF. This RBCC engine study is the first engine test program conducted at the HTF since 1974.
In this report, we present some results of problems investigated during joint research between the Hampton University (HU) Fluid Mechanics and Acoustics Laboratory (FM&AL), NASA Glenn Research Center (GRC) and the Hyper-X Program of the NASA Langley Research Center (LaRC). This work is supported by joint research between the NASA GRC/HU FM&AL and the Institute of Mechanics at Moscow State University (IM/MSU) in Russia under a Civilian Research and Development Foundation (CRDF) grant, #RE1-2068. The main areas of current scientific interest of the FM&AL include an investigation of the proposed and patented advanced methods for aircraft engine thrust and noise benefits. These methods are based on nontraditional 3D (three dimensional) corrugated and composite nozzle, inlet, propeller and screw designs such as the Bluebell and Telescope nozzles, Mobius-shaped screws, etc. These are the main subject of our other projects, of which one is the NASA MURED's (Minority University Research and Education Division) FAR (Faculty Awards for Research) Award, #NAG-3-2249. Working jointly with this project team, our team also analyzes additional methods for exhaust jet noise reduction. These methods are without essential thrust loss and even with thrust augmentation. The research is focused on a wide regime of problems in the propulsion field as well as in experimental testing and theoretical and numerical simulation analyses for advanced aircraft and rocket engines. The FM&AL Team uses analytical methods, numerical simulations and experimental tests at the Hampton University campus, NASA and IM/MSU. The main results obtained by FM&AL team were published in the papers and patents.
A wide-ranging series of tests have been completed that seek to map the effects of installation, including jet by jet interaction effects, on exhaust noise from various nozzles in forward flight. The primary data was far-field acoustic spectral directivity. The goals of the test series were (i) to generate enough data for empirical models of the different effects, and (ii) to provide data for advanced computational noise predictions methods applied to simplified yet realistic configurations. Data is presented that demonstrate several checks on data quality and that provide an overview of trends observed to date. Among the findings presented here: (i) Data was repeatable between jet rigs for single nozzles with and without surfaces to within +/- 0.5 dB. (ii) The presence of a second jet caused a strong reduction of the summed noise in the plane of the two plumes and an increase over the expected source doubling in most other azimuthal planes. (iii) The impact of the second jet was reduced when the jets were unheated. (iv) The impact of adding a second isolated rectangular jet was relatively independent of the nozzle aspect ratio up to aspect ratio 8:1. (v) Forward flight had similar impact on a high aspect ratio (8:1) jet as on an axisymmetric jet, except at the peak noise angle where the impact was less. (vi) The effect of adding a second round jet to a tightly integrated nozzle where the nozzle lip was less than a diameter from the surface was very dependent upon the length of the surface downstream of the nozzle. (vii) When the nozzles were rectangular and tightly integrated with the airframe surface the impact of a second jet was very dependent upon how close together the two jets were. This paper serves as an overview of the test; other papers presented in the same conference will give more detailed analysis of the results.
Not Available
In this paper, we investigate the trade-offs among the subsystems of a hybrid electric vehicle (HEV), e.g., the engine, motor, and the battery, and discuss the related im- plications for fuel consumption and battery capacity and lifetime. Addressing this problem can provide insights on how to prioritize these objectives based on consumers needs and preferences.
Explore the source record for details and available documents.
This report presents the results of a study to develop a procedure for evaluating liquid propellants in order (a) to select the most appropriate propellant (from among those under development) for each of several applications on each of the various missions in the NASA program, or (b) to select new propellants (from among those being proposed) for initiation or continuation of research and development. The analysis begins with a consideration of requirements--either for the specific application or for the various classes of applications. The known characteristics of the propellant or propellants to be evaluated are then put into a convenient form for evaluation. The next step is to determine whether or not there are requirements that simply cannot be met by the propellant. If the propellant passes this test, an optimum vehicle configuration using the propellant (and meeting all requirements) is estimated. (The configuration should be optimized with respect to the total resource consumption for all aspects of the mission, including R&D, production, logistics, and operation.) The total resource consumption for this configuration is then compared with that for similar configurations using other propellants (and meeting all requirements equally well). If all factors have been properly taken into account, this comparison of resource consumption will complete the evaluation. Such an evaluation may be performed several times, in increasing detail and with correspondingly increasing accuracy, as an R&D program proceeds, and the accuracy of the data as well as the cost of the next step in the program increase. The procedure is superior to those in common use in that it minimizes both the amount of analytical work and the number of points at which subjective value judgments are made.
Achieving noise suppression & high thrust performance with plug-type exhaust nozzles for supersonic transports
Plasma-acceleration system in which power is transferred from an rf electromagnetic field to a plasma by means of cyclotron-resonance coupling
Explore the source record for details and available documents.
Explore the source record for details and available documents.